Hikvision UD19517B User guide

Brand: Hikvision

Model: UD19517B

Type: User guide

Hikvision UD19517B is a hybrid control panel that offers advanced security features for both wired and wireless applications. It supports up to 64 zones (8 on-board and 56 wired/wireless), providing comprehensive protection for residential and commercial properties. With built-in Wi-Fi connectivity, it allows for remote access and control via mobile devices or web browsers. The UD19517B also features alarm input/output wiring, RS-485 wiring for peripherals like wireless receivers and keypads, and power supply wiring for reliable operation.

7. Close and lock the case of the control panel.

Speciﬁcaon

23 24 2

Dry Contact

AUX+AUX- D- D+ AUX+

AUX-

DC- DC+

D- D+

N.C

N.O

N.C

N.O

N.C

N.O

N.C

N.O

N.C

N.O

N.C

N.O

N.C

N.O

N.C

N.O

Alarm

Lamp Alarm

Lamp Siren

RS-485

Lead-acid

Battery

14.3VDC

Power Adapter

Z1 C Z2 Z3 C Z4 Z5 C Z6 Z7 C Z8 C1 PGM1 AUX+ BELL+ D+ DC+ BAT+C2 PGM2 C3 PGM3 C4 PGM4 AUX BELL D BATDC

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

2K2

EOL

Only for device with

8 on-board zones

Only for device with

8 on-board zones

C1 PGM1

GPRS

Wi-Fi

3G/4G

CN1

MAIN

AUX

Telephone Module

Telephone Line Cut Off Indicator

Power Indicator

Telephone

Line

Telephone

Line

Telephone

2a2

c2d

2.2KΩ

Peripheral Security Detector

2.2KΩ

Security Control Panel

Peripheral Security Detector

UD19517B-C

2.2K Ω

TAMPER

Detector

2ef

2.2kΩ

Local Zone

Security

Control Panel

8.2kΩ

Local Expanding

Zone

NO C

2.2kΩ

8.2kΩ

14.3V

ENGLISH

Hybrid Control Panel

Quick Start Guide

Diagram References

Installaon and Wiring

Set Up

Set up via Web Client

Telephone Module Wiring

1. Alarm Input Wiring

2. Alarm Output Wiring

3. RS-485 Wiring: Wireless Receiver , keypad, etc,.

4. Power Supply Wiring

NC Detector

NO Detector

Unoccupied Zone

Tamper-proof

Note: Power down the control panel before wiring accessories and peripherals.

Dual-Zone Series Connecon

Dual-Zone Parallel Connecon

1-3. Install the device.

4. Fix the SIM card module (sold separately) and connect the antenna.

5. Fix the telephone module (sold separately).

6. Wire

Wi-Fi antenna.

Network Wiring

Peripherals/Power Supply Wiring

For more acvaon methods ,refer to the User Manual.

1. Enter the device IP address in the web browser.

2. Create a password for admin account to acvate the device.

Defacult IP Address:

Mobile broswer(AP mode):192.168.8.1

Network cable connecon: 192.0.0.64

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Direcve

2014/53/EU, the EMC Direcve 2014/30/EU, the LVD Direcve 2014/35/EU, the RoHS Direcve 2011/65/EU

2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to

your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collecon points. For more informaon see: www.recyclethis.info

2006/66/EC (baery direcve): This product contains a baery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentaon for speciﬁc

baery informaon. The baery is marked with this symbol, which may include leering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the baery to

your supplier or to a designated collecon point. For more informaon see:www.recyclethis.info

About this Manual

The Manual includes instrucons for using and managing the Product. Pictures, charts, images and all other informaon hereinaer are for descripon and explanaon only. The informaon

contained in the Manual is subject to change, without noce, due to ﬁrmware updates or other reasons. Please ﬁnd the latest version of this Manual at the Hikvision website

(hps://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals trained in supporng the Product.

and other Hikvision's trademarks and logos are the properes of Hikvision in various jurisdicons. Other trademarks and logos menoned are the properes of their respecve

owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND

“WITH ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR

A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR

INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF

DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT,

EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS,

AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS

INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH

ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS

PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA

PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS

DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR

FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

1. The addional force shall be equal to three mes the weight of the equipment but not less than 50N. The equipment and its associated mounng means shall remain secure during the

installaon. Aer the installaon, the equipment, including any associated mounng plate, shall not be damaged.

2. Install the equipment according to the instrucons in this manual.

3. To prevent injury, this equipment must be securely aached to the ﬂoor/wall in accordance with the installaon instrucons

INSTALLATION CAUTION

FCC Informaon

Please take aenon that changes or modiﬁcaon not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause

harmful interference to radio or television recepon, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separaon between the equipment and receiver.

—Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

FCC Condions

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operaon

● indicates hazardous live and the external wiring connected to the terminals requires installaon by an instructed person.

● This equipment is suitable for mounng on concrete or other non-combusble surface only.Coper or coper wire cannot be exposed at the electrical terminal.

● In the use of the product, you must be in strict compliance with the electrical safety regulaons of the naon and region.

● CAUTION: To reduce the risk of ﬁre, replace only with the same type and rang of fuse.

● A readily accessible disconnect device shall be incorporated external to the equipment, rated 6A.

● An all-pole mains switch shall be incorporated in the electrical installaon of the building.

● Ensure correct wiring of the terminals for connecon to an AC mains supply.

● The equipment has been designed, when required, modiﬁed for connecon to an IT power distribuon system.

● No naked ﬂame sources, such as lighted candles, should be placed on the equipment.

● The serial port of the equipment is used for debugging only.

● Keep downward when moving or using the equipment.

Baery Cauon

1. This equipment is not suitable for use in locaons where children are likely to be present.

2. CAUTION: Risk of explosion if the baery is replaced by an incorrect type.

3. Improper replacement of the baery with an incorrect type may defeat a safeguard (for example, in the case of some lithium baery types).

4. Do not dispose of the baery into ﬁre or a hot oven, or mechanically crush or cut the baery, which may result in an explosion.

5. Do not leave the baery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of ﬂammable liquid or gas.

6. Do not subject the baery to extremely low air pressure, which may result in an explosion or the leakage of ﬂammable liquid or gas.

7. Dispose of used baeries according to the instrucons.

CAUTION

Class II equipment

To idenfy equipment meeng the safety requirements speciﬁed for Class II equipment according to IEC 61140.

Note:

The Posion of the double-square symbol shall be such that it is obvious that the symbol is part of the technical informaon and can in no way be confused with the manufacturer’s name or

other idenﬁcaons.

User Manual Legal and Regulatory Informaon

Fuse Cutout: rated voltage 250 V, rated current 6 A.

Mains supply cables need to meet IEC 60332 or UL cerﬁcaon.

AUX+ output interface: DC12 V, 1000 mA.

BELL+ output interface: DC12 V, 500 mA.

Allowed baeries speciﬁcaons:

rated voltage 12 V, capacity 7Ah, Min. charging current ≥ 1 A,

ﬂame class of shell V-0.

Reset:

Aer the device is started, hold the reset buon for 10 seconds to reset the device.

DS-PHA64-P2 DS-PHA64-W4P2

Detector

Relay output

RS-485 wireless

receiver

Siren

Keyfob

Alarm input Paron

Noﬁcaon

Network camera N/A 4

Protocol Protocol

Wired network

Cellular network

Wi-Fi/AP Standard N/A 802.11b/g/n

User

Tag/Card

Operaon temperatue

Operaon humidity

Dimension (W × H × D)

Weight

Model

Device

connecon

UP to 64 (8 on-board, 56 wired/wireless)

Up to 64 (4 on-board, 60 wired/wireless)

1 wired sirens (on-board connecon)

2 wireless sirens

Up to 7

–10 °C to 55 °C (-4 °F to 122 °F)

10% to 90% (No condensing)

310 mm (12.2") × 225 mm (8.6") × 95 mm

(3.7")

ISAPI, DC09, ISUP

Network 10M/100M Ethernet

(with 3G/4G/GPRS module)

Others

User

Installer: 1; Administrator: 1;

Manufactuer:1

Operator: 45

Funcon SMS&Phone call with 3G 4G GPRS

AP STA AP STA

Note: Aer the user connects the power cord according to the ﬁgure, ﬁx it with a cable

e to avoid the cable falling oﬀ due to external force, causing a short circuit and other

dangers.

1.15 kg 1.17 kg

Security

Control Panel Local Zone

Local Expanding Zone

Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China

alternate

Hikvision UD19517B User guide

Hikvision UD19517B User guide

Hikvision UD19517B User guide

Related papers

Other documents