MULTISPAN UTR-413 Owner's manual

Brand: MULTISPAN

Model: UTR-413

Type: Owner's manual

www.multispanindia.com

Page - 1UTR-413

Technical Specification

Connection Diagram

OPERATING MANUAL

UNIVERSAL TIMER

UTR-413

Output

Power Supply

Reset

Protection Level

Operating

Relative

(As per request)

Temperature

Humidity

1 relay, 2 C/O contact, 230V AC, 5A

100 to 250V AC, 50 / 60 Hz, Approx 4VA

Front key & Back Reset

IP-65(Front side) AS per IS/IEC 60529:2001

0°C To 55°C

Up to 95% RH Non Condensing

Model

Display

Size(HXWXD)

Panel Cutout

Input

45 X 45 mm

48 X 48 X 95 mm

3 Digit, 56”, 7 Segment LED

UTR 413

NPN Proximity & Micro Switch

Notes:

1). POWER ON : Timer starts counting as soon as it gets power supply.

2). By default Cycle ON Mode is provided. Please refer programming guide to change to Cycle OFF

Delay ON/ Delay OFF Mode.

3). Instrument can be Start and hold by front key, when it is in trigger pulse mode.

4). If we set cycle parameter 000 then the cycle timer will continue the cycle infinitely.

5). In enable pulse mode, if the memory parameter is selected YES and If the enable pulse is gone

& receive again before the set point, the timer will resume from the old value.

6). In enable pulse mode, if the memory parameter is selected NO and If the enable pulse is gone

& receive again before the set point, the timer will start 000.

1 2 3

UTR 413

SET ENT

RESET

Time

START HOLD

100

250V AC

50/60 HZ

4VA

RELAY

RESET

M/S PROXI NPN

I/P

+12V

GND

UTR 413

Made in India

www.multispanindia.com

Page - 2UTR-413

Parameter Menu

Press key 10 Sec

2 5

F U N

P A S

SELECT BY

key

SELECT BY

key

SELECT BY

key

SELECT BY

SELECT BY SELECT BY

SELECT BY + Key

SELECT BY

key

key key

key

SELECT BY

key

SELECT BY

key

Select:

Cycling Mode

delayed ON or

delayed OFF or

999 SEC 999 SEC

999 SEC

999 miN 999 miN

999 miN

999 hr 999 hr

999 hr

9.59 min 9.59 min

9.59 min

9.59 hr 9.59 hr

9.59 hr

99.9 hr 99.9 hr

99.9 hr

9.99 SEC 9.99 SEC

9.99 SEC

99.9 SEC 99.9 SEC

99.9 SEC

99.9 Min 99.9 Min

99.9 Min

U N 1

p L s

U N 2

M I N

T R G

M I N

M I N M I N

M I N

H R

E n B

H R H R

H R

S E C

P O N

S E C

R N G R G 1

R G 2

S E C

Time-1 select:

Time-2 select: Sec, Min, Hr

Sec, Min, Hour

d I r

U P D n

Memory Retain (yes / no)

Set Pulse

(Trigger,Enable, Power ON)

Set Pulse

(Trigger,Enable, Power ON)

d I r

M E M

U P

Y E S

D n

N O

SELECTED BY

KEY

SELECTED BY

KEY

SELECTED BY

KEY

SELECTED BY

KEY

SELECTED BY

KEY

If Delayed ON/ Delayed OFF is selected

If Cycling Mode is selected

Password

Time Count : UP/Down

Set Range

d o f d o n C O N C O F C Y L

9 9 9

Function will change when display

start blinking

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key

SET

Press key to save & exit

RESET

ENT

DESCRIPTION

Time - 1

Delayed OFF

Unit - 2 for Time - 2

Cycling time

Minute set for Time - 1 or 2

Up counting

Memory Retain : Yes / No

Enable Trigger Power ON

DISPLAY

SR.

Time - 2

Password

Unit - 1 for Time - 1

Delayed function

Seconds set for Time - 1 or 2

Direction of time counting

Delayed ON

Hour set for Time - 1 or 2

Down counting

T M 1

T M 2

p a s

F U N

C Y L

D O N

D O F

U N 1

U N 2

S E C

M I n

H R

d I r

U P

m E M

P L S

D N

Page - 3 www.multispanindia.com

UTR-413

1). Turn ON instrument. SET time according to your requirement.

2). In running mode, upper display indicates current TIME value and lower display shows SET

time value. Relay ON or OFF controls depends on set time.

3). Relay operation is according to selection of Delay ON or Delay OFF in programming menu.

4). In cycling mode, relay will turn on for ON time (time-1) & relay will turn off for OFF time

(time-2) and this ON-OFF process will continue.

5). To reset the time, press Reset Key.

Working

Set time mode

Display Message And Their Meaning

T I m

1 2 3

T M 1

1 2 3

Cycle OFF time (time-2)

press key to

set cycle ON time

press key to

set cycle OFF time

press key to

set time T M 2

1 2 3

If Delayed ON/ Delayed OFF is selected If Cycling Mode is selected

Press key

SET

Press key

SET

Press key

SET

Press key to save & exit

RESET

ENT

MODEL A

48mm 48mm 44mm 44mm 3mm 95mm

D E

DIMENSIONS

Product improvement and upgrade is a constant procedure. So for more updated operating information and support,

Please contact our helpline : +91-9978991474/76/82 or Email at ser[email protected] Ver: 2001

All safety related codifications, symbols and instructions that appear in this operating manual

or on the equipment must be strictly followed to ensure the safety of the operating personnel as

well as the instrument.

If all the equipment is not handled in a manner specified by the manufacturer, it might impair the

protection provided by the equipment .

=> Read complete instructions prior to installation and operation of the unit.

WARNING : Risk of electric shock.

3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires

should have insulations capacity made of at least 1.5kV.

2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of equal size shall

be made with shortest connection.

1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the wiring

arrangement. Do not touch the terminals while power is being supplied.

4) A better anti-noise effect can be expected by using standard power supply cable for the instrument.

1) This equipment, being built-in-type, normally becomes a part of main control panel and such in case the

terminals do not remain accessible to the end user after installation and internal wiring.

2) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product

or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator.

3) Circuit breaker or mains switch must be installed between power source and supply terminal to

facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be

installed at convenient place normally accessible to the operator.

4) Use and store the instrument within the specified ambient temperature and humidity ranges as

mentioned in this manual.

Warning Guidelines

Safety Precautions

Installation Guidelines

Mechanical Installation

Maintenance

1) Prepare the panel cutout with proper dimensions as show above.

2) Fit the unit into the panel with the help of clamp given.

3) The equipment in its installed state must not come in close proximity to any heating source,

caustic vapors, oils steam, or other unwanted process by products.

4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the

screws on the terminal block using the tightening torque of the range of 1.2 N.m.

5) Do not connect anything to unused terminals.

1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.

2) Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any other cleaning agent.

3) Fusible resistor must not be replaced by operator.

Page - 4 www.multispanindia.com

UTR-413

1 2 3

UTR 413

SET ENT

RESET

Time

START HOLD

MULTISPAN UTR-413 Owner's manual

MULTISPAN UTR-413 Owner's manual

MULTISPAN UTR-413 Owner's manual

Related papers

Other documents