Osram LINEARlight Flex Diffuse User guide

LINEARlight Flex Diffuse
Osram
Brand
Osram
Model
LINEARlight Flex Diffuse
Type
User guide
Technical application guide
LINEARlight Flex Diffuse (LFD)
www.osram.com/flex
Light is OSRAM
LINEARlight Flex Diffuse (LFD) | Contents
2
Please note:
All information in this guide has been prepared with great care. OSRAM, however, does not accept liability for possible
errors, changes and/or omissions. Please check www.osram.com or contact your sales partner for an updated copy of
this guide. This technical application guide is for information purposes only and aims to support you in tackling the challenges
and taking full advantage of all opportunities the technology has to offer. Please note that this guide is based on own
measurements, tests, specific parameters and assumptions. Individual applications may not be covered and need different
handling. Responsibility and testing obligations remain with the luminaire manu facturer/OEM/application planner.
Contents
1 Product overview 03
1.1 General features 03
1.2 Application areas 03
1.3 LINEARlight Flex Diffuse White TOP 03
1.4 LINEARlight Flex Diffuse White SIDE 03
1.5 Nomenclature 04
1.6 Accessories 04
2 Installation 06
2.1 Precautionary measures 06
2.2 Connection with CONNECTsystem Diffuse 07
2.2.1 Basics 07
2.2.2 Mechanical dimensions 08
2.3 Assembly 08
2.3.1 Assembly with middle power feeder 08
2.3.2 Assembly with strip-to-strip middle jumper 09
2.4 Installation with LINEARlight Flex Diffuse mounting system 10
2.5 Custom versions 15
2.5.1 General description 15
2.5.2 Technical details 15
3 System connection 16
3.1 Basic steps of system planning 16
3.2 Standard connection 16
3.3 Parallel and series connection 16
3.4 Temperture 16
4 Flexessories 17
3
LINEARlight Flex Diffuse (LFD) | Product overview
1.1 General features
—Highly uniform flexible light
—Continuous light without shadows
—Excellent mechanical stability
—Extremely good optical stability over time,
no yellowing effect
—Fine white binning (3 SDCM)
—Dimmable (PWM)
—Lifetime of up to 60000 hours (L90B10) at 25 °C
—Flammability: glow wire test at 650 °C – EN 60598-1
—Mixed gas corrosion test – IEC 60068-2-60
—IP67 or IP66 protection with high-performance silicone
—Encapsulated electronics
—UV-resistant
—Salt-mist-proof
—Easy installation
—Adhesive tape for easy mounting
—Connectors and aluminum profiles available
—Scalable system
—Cuttable every 5 cm
— 24 V system with matching OPTOTRONIC
LED driver and light management system
—Top-emitting and side-emitting versions:
TOP (T) and SIDE (S)
1.2 Application areas
LINEARlight Flex Diffuse (LFD) are suitable for various
appli cations that require a nice-looking, uniform light line
with no dots, e.g. indoor and outdoor decoration. Together
with polished architectural materials, LFD can also be
effectively used for cove or high-class furniture lighting,
where the indirect light is reflected by the surfaces.
Applications at a glance:
—General and cove lighting
—Marine lighting, wall integration
—Path illumination, illuminated signs
—Spa lighting
—Outdoor facade decoration
1.4 LINEARlight Flex Diffuse White SIDE
Available versions: 400, 600, 1 000 lm/m
Luminous efficacy: up to 82 lm/W
Available CCT: 2 400 K, 2 700 K, 3 000 K,
3 500 K, 4 000 K, 6 500 K
Available CRI: 80, 90
Available lengths: LFD400T = 10 m,
LFD600S = 6 m, LFD1000S = 4 m
Bending direction:
1 Product overview
Allowed:
Allowed: Not allowed:
Not allowed:
1.3 LINEARlight Flex Diffuse White TOP
Available versions: 400, 800, 1 300 lm/m
Luminous efficacy: up to 82 lm/W
Available CCT: 2 400 K, 2 700 K, 3 000 K,
3 500 K, 4 000 K, 6 500 K
Available CRI : 80, 90
Available lengths: LFD400T = 10 m,
LFD800T = 6 m, LFD1300T = 4 m
Bending direction:
4
LINEARlight Flex Diffuse (LFD) | Product overview
1.5 Nomenclature
LFD 400 T-G2-824-10
LINEARlight Flex Diffuse
Lumen output [lm/m]
Generation
Color coding in this example:
CRI: 80, CCT: 2 400 K
Overall length [m]
Light-emitting surface
T = TOP
S = SIDE
1.6 Accessories
Connectors / End cap
Product type LINEARlight Flex Diffuse (LFD) TOP LINEARlight Flex Diffuse (LFD) SIDE
Middle power feeder
FX-DCS-G1-CM2PF-IP67-0500-X5 FX-DCS-G1-CM2PF-IP67-0500-X5
Strip-to-strip middle jumper
FX-DCS-G1-CM2PJ-IP67-0190-X5  FX-DCS-G1-CM2PJ-IP67-0190-X5 
Endcaps and glue
FX-DCS-G1-ECT-KIT20 FX-DCS-G1-ECS-KIT20
Double-sided endcaps and glue
FX-DCS-G1-EHT-KIT20 FX-DCS-G1-EHS-KIT20 
Silicone glue 25 g
FX-DCS-G1-GL-25 FX-DCS-G1-GL-25
5
LINEARlight Flex Diffuse (LFD) | Product overview
Mounting brackets
Product type LINEARlight Flex Diffuse (LFD) TOP LINEARlight Flex Diffuse (LFD) SIDE
Mounting bracket
FX-LFDM-G1-BT-17H11 FX-LFDM-G1-BS-12H13
Mounting bracket
with additional wing
FX-LFDM-G1-BTL-17H11E9 FX-LFDM-G1-BSL-12H13E9 
Aluminum profiles
Product type LINEARlight Flex Diffuse (LFD) TOP LINEARlight Flex Diffuse (LFD) SIDE
Standard aluminum profile
FX-LFDM -G1-TT-16H16-200 FX-LFDM-G1-TS-16H16-200
Alternative aluminum profile
FX-LFDM-G1-TTL-16H11W10-200 FX-LFDM-BEND-1000 
6
LINEARlight Flex Diffuse (LFD) | Installation
2 Installation
2.1 Precautionary measures
Before installing LINEARlight Flex Diffuse, attention should
always be paid to the following important issues:
ESD
Be aware that the products can be damaged by electro-
static discharge (ESD). Earthing is a very effective measure
to avoid damaging effects due to electrostatic discharge.
Therefore, use a personal earthing system (ESD field kit)
during mounting to prevent the build-up of static charge.
Cleaning
Depending on the surface, use a multi-purpose cleaner,
such as isopropyl alcohol, to provide a clean and dry
mounting surface, which is free of oils, silicone coatings
and dirt particles.
Mechanical forces
Avoid mechanical forces on the connector (feeder) and the
LEDs. A strain relief is recommended. In addition, mechani-
cal stress must not be applied to the LED module itself (e.g.
no twisting or bending in excess of the allowed radius as
shown in the next images from 1 to 3).
IP rating
The IP rating specifies the degree of protection against the
intrusion of solid objects (including body parts such as
hands and fingers), dust and water in electrical enclosures.
While the first digit of the IP rating indicates the protection
against foreign bodies, the second digit indicates the pro-
tection against water. For more details on IP rating, please
refer to “Technical application guide – IP codes in accor-
dance with IEC 60529 and external environment impacts”
in the following OSRAM DS website section:
https://www.osram.com/ds/app-guides/index.jsp
The following IP rating applies to LINEARlight Flex Diffuse:
IP66: [6]
Full protection against contact and penetration of dust
[6] Protection against ingress of water in case of
powerful water jets
IP67: [6]
Full protection against contact and penetration of dust
[7] Protection against ingress of water in case
of temporary flooding
Note: Permanent submersion is not allowed.
Cutting
Ensure that the LED strips are cut properly at an angle of
90° before attaching the connector!
3
Tc Tc Tc
IP67PROT LF06P2-W4F-8xx-P 27R-P n007H made in italy InQbl.745kaA4PROT
Tc Tc
SLIM
LF06A-W3F-8xx-P
LF06P2-W4F-8xx-P
90°
90°
90°
90°
LF06A-P: ≤70°C
LF06P2-P: ≤50°C
OSRAM GmbH
Steinerne Furt 62
86167 Augsburg, Germany
www.osram.com
G10466239C10449058
LF06A-P
LF06P2-P
#18222
black
score dimension 148 x 210 mm
2
LINEARlight FLEX DIFFUSE
LINEARlight FLEX DIFFUSE Monochrome
LINEARlight FLEX DIFFUSE White
G15010075_UI_LINEARlight_Flex_DIFFUSE_Top_Side_MiI_03.indd 2G15010075_UI_LINEARlight_Flex_DIFFUSE_Top_Side_MiI_03.indd 2 22.12.16 11:4522.12.16 11:45
#18222
black
score dimension 148 x 210 mm
LINEARlight FLEX DIFFUSE
3
≤ 65 °C
G15010075_UI_LINEARlight_Flex_DIFFUSE_Top_Side_MiI_03.indd 3G15010075_UI_LINEARlight_Flex_DIFFUSE_Top_Side_MiI_03.indd 3 22.12.16 11:4522.12.16 11:45
7
LINEARlight Flex Diffuse (LFD) | Installation
2.2 Connection with CONNECTsystem Diffuse
2.2.1 Basics
LINEARlight Flex Diffuse LED modules (TOP and SIDE) are
compatible with the connectors dedicated for this product
family. There are two components that can be used to
power these LED modules:
Middle power feeder
This is the connector that connects the Flex Diffuse product
to an LED driver. All LINEARlight Flex Diffuse LED modules
are sold with already one of these connectors installed on
the product. It consists of two parts:
—The transparent cage
—The white connector
Both parts are available either with the product FX-DCS-G1-
CM2PF-IP67-0500 or with the KIT FX-DCS-G1-CM2PF-IP67.
Strip-to-strip middle jumper
This is a connector that connects two Flex Diffuse products
when only one of these is powered by a 24 VDC LED driver.
It consists of three parts:
—Two transparent cages
—One white jumper with two heads
They are available either in the product FX-DCS-G1-CM2PJ-
IP67-0190 and in the KIT FX-DCS-G1-CM2PJ-IP67
LINEARlight Flex Diffuse LED modules are also available
with pre-mounted wires. This option is described in the
chapter "2.5 Custom versions"
Specially developed for LINEARlight Flex Diffuse LED
modules, these power feeders offer great advantages for
your installations because:
—The installation will be easy thanks to the low number
(only 2) of components (connector + cage)
—The LED modules can be cut as needed (min. segment
length that can be used with this connector is 10 cm)
—Highly reliable connection
—Thanks to the transparent cage and to the special de-
sign that allows the electrical connection at the bottom
of the LED module, this connector can be installed
along the entire
length of the LINEARlight Flex Diffuse
LED module. The bottom
side of each module is marked
with a “scissors” symbol every 5 cm. This indicates the
point where the LED module can be cut and where the
connector can be installed.
—For longer installations where several LED modules have
to be installed in series, the absence of a connector on
the end allows to have a continuous and homogenous
line of light without shadowing in between.
Middle power feeder
LINEARlight Flex Diffuse
Competitor
Competitor
8
LINEARlight Flex Diffuse (LFD) | Installation
2.2.2 Mechanical dimensions
2.3.1 Assembly with middle power feeder
To have a clear indication about the space that each type of
connector needs in the installation, please have a look at the
images below.
2.3 Assembly
1. Components for assembly:
— LINEARlight Flex Diffuse TOP or SIDE
(LFD600S)
— Connector: Middle power feeder
(transparent closing cage + white connector)
2. Use a box cutter to cut the LFD module at
one of the “scissors” symbols on the bottom
side.
3. The connector can be installed over any
“scissors” symbol along the whole module.
Once you have decided on the right point,
slightly incise the transparent liner over the
“scissors” symbol and remove 2 cm of the
liner material in both directions.
4. Insert the transparent cage as shown in
the picture. It has to be centered with the
“scissors” symbol.
5. Take the white connector and check that its
polarity is aligned with the polarity indicated
on the bottom side of LED module.
6. Hold the white connector above the trans-
parent cage and gently press it down until
you feel both sides close with a click.
6
LINEARlight FLEX DIFFUSE
TOP
FX-DCS-G1-CM2PF-IP67-0500-X5
EAN 4052899451971
FX-DCS-G1-CM2PJ-IP67-0190-X5
EAN 4052899452039
5x
5x
LINEARlight FLEX DIFFUSE TOP White
FX-DCS-G1-CM2PF-IP67-0500-X5
EAN 4052899451971
6
LINEARlight FLEX DIFFUSE
TOP
FX-DCS-G1-CM2PF-IP67-0500-X5
EAN 4052899451971
FX-DCS-G1-CM2PJ-IP67-0190-X5
EAN 4052899452039
5x
5x
LINEARlight FLEX DIFFUSE TOP White
FX-DCS-G1-CM2PJ-IP67-0190-X5
EAN 4052899452039
LINEARlight Flex Diffuse (LFD) | Installation
7. Ensure that the “hourglass” mark is still visible
but not completely visible.
2.3.2 Assembly with strip-to-strip middle jumper
1. Components for assembly:
— LINEARlight Flex Diffuse TOP or SIDE
(LFD600S)
— Strip-to-strip middle jumper (transparent
closing cages + white bridge connector)
2. Cut the LED module as described in
paragraph 2.3.1.
3. For each connector head of the jumper,
follow the same mounting steps as described
in paragraph 2.3.1, starting from point 3.
Please note: When connecting two LINEARlight
Flex Diffuse LED strips with the connector,
ensure that the same polarities are always properly
connected to each other.
Please note: When connecting multiple LINEARlight
Flex Diffuse LED strips in series, always consider the
allowed power per single LED driver.
9
#18222
black
score dimension 148 x 210 mm
6
LINEARlight FLEX DIFFUSE
1a
1b
234
“click”
“click”
“click”
“click”
TOP
G15010075_UI_LINEARlight_Flex_DIFFUSE_Top_Side_MiI_03.indd 6G15010075_UI_LINEARlight_Flex_DIFFUSE_Top_Side_MiI_03.indd 6 22.12.16 11:4522.12.16 11:45
8. To install the end cap, remove the protection
tape from the end of the LED module. Insert
the silicone glue into the end cap and then
insert the LED module. Wait 20 minutes for
the glue to dry before proceding with the
installation. In case of a double-sided end
cap, the process is the same for both parts
of the LED strip.
9. Connect the LED module to the LED driver.
Observe the correct polarity (red+/black-).
Perform a final operating test
10
FX-LFDM-G1-BTL-17H11E9
LINEARlight Flex Diffuse (LFD) | Installation
2.4 Installation with LINEARlight Flex Diffuse mounting system
The images below show the mechanical details of installations of LINEARlight
Flex Diffuse LED modules with the dedicated accessories developed for this
product family.
LINEARlight Flex Diffuse TOP
FX-LFDM-G1-BT-17H11
16.2
20
AA
11
2
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BT-17H11
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
AA
11
2
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BT-17H11
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
AA
11
2
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BT-17H11
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
12,8
1,8
4,7
19
200 200
16,2
18,3
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD TOP + CONN + CLIP BT_17H11
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
19
1 9
A
A
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BTL-17H11E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
19
1 9
A
A
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BTL-17H11E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
19
1 9
A
A
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BTL-17H11E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
1,8
20,8
5,7
19
200 200
18,3
16,2
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD TOP + CONN + CLIP BTL_17H11
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
19
1 9
A
A
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BTL-17H11E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
16.2
20
19
1 9
A
A
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BTL-17H11E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
18.3
16.2
16.2
18.3
11
LINEARlight Flex Diffuse (LFD) | Installation
FX-LFDM-G1-TT-16H16-200
23,1
1,8
300
21,4
18,3
6,2
17
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD TOP + CONN + TRACK TT + CLIP BMZI
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
FX-LFDM-G1-TTL-16H11W10-200
19
1,8
17,3
18,3
16,2
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD TOP + CONN + TRACK TT
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
2000
15.5
16.2
10.2
8.2
3.5
350 125
A
A
6.3
3.4
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TT-16H16-200
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
2000
15.5
16.2
10.2
8.2
3.5
350 125
A
A
6.3
3.4
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TT-16H16-200
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
2000
15.5
16.2
10.2
8.2
3.5
350 125
A
A
6.3
3.4
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TT-16H16-200
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
20
A
A
9.5
1.6
17
5.7
01
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-QMS-G1-BMZI-DIV1
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
20
A
A
9.5
1.6
17
5.7
01
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-QMS-G1-BMZI-DIV1
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
24
4,9
22,3
1,8
18,3
16,2
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD TOP + CONN + TRACK TTL
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
125 350
5
A
A
20.5
16.2
10
2000
3.4
6.3
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TTL-16H11W10
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
2000
15.5
16.2
10.2
8.2
3.5
350 125
A
A
6.3
3.4
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TT-16H16-200
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
FX-LFDM-G1-TT-16H16-200 + clip BMZI
125 350
5
A
A
20.5
16.2
10
2000
3.4
6.3
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TTL-16H11W10
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
18.3
6.2
17
18.3
16.2
18.3
16.2
12
LINEARlight Flex Diffuse (LFD) | Installation
LINEARlight Flex Diffuse SIDE
FX-LFDM-G1-BS-12H13
FX-LFDM-G1-BSL-12H13E9
200 200
19
13
16
18.3
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + CLIP BS
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
20
AA
6.3
3.4
SECTION
A-A
11.5
1.50
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BS-12H13
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
20
AA
6.3
3.4
SECTION
A-A
11.5
1.50
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BS-12H13
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
20
AA
6.3
3.4
SECTION
A-A
11.5
1.50
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BS-12H13
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
200 200
19
13
16
18.3
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + CLIP BS
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
200 200
13
19
6
23.10
18.3 6.9
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + CLIP BSL
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
200 200
13
19
6
23.10
18.3 6.9
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + CLIP BSL
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
20
AA
20
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BSL-12H13E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
20
AA
20
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BSL-12H13E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
20
AA
20
6.3
3.4
SECTION
A-A
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-LFDM-G1-BSL-12H13E9
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
13
LINEARlight Flex Diffuse (LFD) | Installation
FX-LFDM-G1-TS-16H16-200
FX-LFDM-G1-TS-16H16-200 + BMZI
FX-LFDM-BEND-1000
19
17.3
16.2
18.3
4.5
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + TRACK TS
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
23.1
21.4
300
18.3
6.2
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + TRACK TS + BMZI
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
23.1
21.4
300
18.3
6.2
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + TRACK TS + BMZI
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
20
A
A
9.5
1.6
17
5.7
01
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-QMS-G1-BMZI-DIV1
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
20
A
A
9.5
1.6
17
5.7
01
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-QMS-G1-BMZI-DIV1
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
20
A
A
9.5
1.6
17
5.7
01
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 2:1
FX-QMS-G1-BMZI-DIV1
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
19
12.3
5.7
16.3
18.3
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
1.1m LFD SIDE + CONN + BENDABLE TRACK
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
12.3
11.4
8.2 2.2
998
10.3
12.3
3.4
5
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
BENDABLE TRACK.STEP
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
12.3
11.4
8.2 2.2
998
10.3
12.3
3.4
5
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
BENDABLE TRACK.STEP
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
19
12.3
5.7
16.3
18.3
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
1.1m LFD SIDE + CONN + BENDABLE TRACK
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
125 350
2000
A
A
14.2
16.2
B
B
6.3
3.4
6.3
3.4
SECTION
B-B
SCALE
1 : 1
16.5
16.2
10
4.5
SECTION
A-A
SCALE
1 : 1
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:20
FX-LFDM-G1-TS-16H16-200 4052899544925.STEP
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
19
17.3
16.2
18.3
4.5
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
0.5m LFD SIDE + CONN + TRACK TS
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
14
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:10
BENDABLE + SCREW
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
Notes for FX-LFDM-BEND-1000 installation
—To install this bendable profile correctly, it is recommended
to use at least 10 screws per meter.
—The installation of this bendable profile must not be done with countersunk screws. The thickness of the screw head has
to be less than 1.8 mm.
—Do not remove the liner from the adhesive tape on the bottom of LINEARlight Flex Diffuse SIDE.
—During the design of the installation, please consider that the light output of LINEARlight Flex Diffuse SIDE can only have
an orthogonal direction to the installation surface.
LINEARlight Flex Diffuse (LFD) | Installation
15
2.5 Custom versions
2.5.1 General description
The LINEARlight Diffuse product family is also available with some customizations that can be defined by using the Speaking
Code Generator available via the following link:
https://www.osram.com/ds/flexible-lighting-systems/tools-and-support/ds_speakingcodegenerator_diffuse.jsp
Using a reference code as a basis, the following is a description of each field that makes up the Speaking Code:
LFD-400T-924-10-C-T-L1-50-F-G2.1
Product family. This is a fixed field. LFD = LINEARlight Flex Diffuse
Lumen output [lm/m] and light-emitting surface
T = TOP
S = SIDE
Color coding in this example: CRI = 90, CCT = 2400 K
Product length in cm (from 10 up to 1000 cm)
Connection system (standard connector or soldered cable). In this example: C = connector
Adhesive tape or not. In this example: T = adhesive tape availble
Number of connection system applied on each length (on one end or on both).
In this example: L1 = One end with soldered cable
Wire length [cm]
Wire ends (flying leads or with connector). In this example: F = flying leads
Generation (e.g.: 2.1)
2.5.2 Technical details
If a system connection based on soldered cables is defined in the Speaking Code, the section of LINEARlight Flex Diffuse
close to the connection area is different from that defined in the previous paragraph. More details are shown in the
images below.
The drawing above shows the cable applied on a LINEARlight Flex Diffuse TOP. The same concept with the same
dimensions is also available for LINEARlight Flex Diffuse SIDE.
Cable on the bottom
16,5
5,7
12
3,1 5,6
12
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:2
LFD CUSTOM_CAVO BOTTOM
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
11,5
10
3,1
8,1
14,1
5,6
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:5
LFD CUSTOM_CAVO ON THE END
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
11,5
10
3,1
8,1
14,1
5,6
UNLESS OTHERWISE SPECIFIED:
CHECKED
SIZE
APPLICATION
TITLE:
PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC
TOLERANCING PER:
Q.A.
FINISH
DWG. NO.
DATE
USED ON
A
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH
BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
NEXT ASSY
MATERIAL
NAME
REV
DO NOT SCALE DRAWING
SCALE: 1:5
LFD CUSTOM_CAVO ON THE END
ENG APPR.
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
COMMENTS:
DRAWN
MFG APPR.
SHEET 1 OF 1
2 1
A
B
A
B
12
<COMPANY NAME>
Cable at the end
The drawing above shows the cable applied on a LINEARlight Flex Diffuse TOP. The same concept with the same
dimensions is also available for LINEARlight Flex Diffuse SIDE.
LINEARlight Flex Diffuse (LFD) | Installation
16
3 System connection
3.1 Basic steps of system planning
1. Select the suitable LINEARlight Flex Diffuse LED module
with regard to your application and its requirements
(level of light output, bending direction, etc.).
2. Determine the required level of control for the application
(dimming, control interface, etc.).
3. Determine the number of LINEARlight Flex Diffuse LED
modules and total wattage to be installed.
4. Consider all possible limitations of the setup: Cable
lengths (for this, please have a look at the application
guide for OPTOTRONIC constant-voltage LED drivers
and at the technical documentation available for each
OT CV device), thermal load, mechanical forces, ambient
conditions and all other factors that may occur in a
certain application.
3.2 Standard connection
The electrical connection between the secondary side of the
OPTOTRONIC LED driver and the LINEARlight Flex Diffuse
LED module must be IP-rated. Therefore, a clamp with an
appropriate IP rating has to be applied.
Note:
For further information, please see the datasheets of the
OPTOTRONIC LED drivers.
3.3 Parallel and series connection
If multiple LINEARlight Flex Diffuse LED modules are
connected to one LED driver, they must be connected
in parallel as shown in the image below.
Series connection, made possible by using FX-DCS-G1-
CM2PJ-IP67-0190-X5, is allowed. However, the connection
of different LED modules to the ECG must be done carefully,
without exceeding the maximum operable length of LED
modules (the product length is a technical information available
on each technical datasheet or specification sheet of each
LFD product).
However, more sections cannot be connected in series if
the sum of their lengths is longer than the maximum operable
length of the standard product.
3.4 Temperature
For final application, it is important to check if the case
temperature tc of the product is lower than the maximum
declared value. An ambient temperature change during
the day (due to, for example, a different sun exposure or
the turning on of a heating system) can in fact influence
the tc value when the LED module is on. For this reason, it is
required to measure the case temperature at the tc point in
the worst possible conditions of the installation. Where to
measure the case temperature tc and the respective maximum
temperature values are shown below:
OPTOTRONIC
~230 V
LINEARlight
Flex Diffuse
+
-
+
-
Apply a clamp with
appropriate IP rating
OPTOTRONIC
~230 V +
--24 V
+
-
+
-
+
-
Example:
LFD400S-G2-xxxx-10 is a 10-m product. A section of
3 m can be connected with another one of 7 m (10 m in total),
as shown below:
7 m 5 m
230 V OT
230 V OT
10 m 1 m
230 V OT
7 m 3 m
tc
≤ 75 °C
LINEARlight Flex Diffuse (LFD) | System connection
17
Product type Product description Product code (EAN 10) Package content (EAN 10)
Middle power feeder FX-DCS-G1-CM2PF-IP67-0500-X5 4052899451971 5 x feeder
Strip-to-strip middle jumper FX-DCS-G1-CM2PJ-IP67-0190-X5 4052899452039 5 x jumper
Feeder kit with end caps and glue FX-DCS-G1-CM2PF-IP67-TOPKIT5 4052899451995 5 x feeder, 10 x endcap, 1 x glue (5g)
Jumper kit with end caps and glue FX-DCS-G1-CM2PJ-IP67-TOPKIT5 4052899452053 5 x jumper, 10 x endcap, 1 x glue (5g)
End caps and glue FX-DCS-G1-ECT-KIT20 4052899452107 20 x endcap, 2 x glue (5g)
Double-sided end caps and glue FX-DCS-G1-EHT-KIT20 4052899452176 20 x endcap, 1 x glue (25g)
Silicone glue 25 g FX-DCS-G1-GL-25 4052899452244 1 x glue (25g)
CONNECTsystem Diffuse for LINEARlight Flex Diffuse TOP
Product type Product description Product code (EAN 10) Package content (EAN 10)
Middle power feeder FX-DCS-G1-CM2PF-IP67-0500-X5 4052899451971 5 x feeder
Strip-to-strip middle jumper FX-DCS-G1-CM2PJ-IP67-0190-X5 4052899452039 5 x jumper
Feeder kit with end caps and glue FX-DCS-G1-CM2PF-IP67-SIDEKIT5 4052899452015 5 x feeder, 10 x endcap, 1 x glue (5g)
Jumper kit with end caps and glue FX-DCS-G1-CM2PJ-IP67-SIDEKIT5 4052899452077 5 x jumper, 10 x endcap, 1 x glue (5g)
End caps and glue FX-DCS-G1-ECS-KIT20 4052899452121 20 x endcap, 2 x glue (5g)
Double-sided end caps and glue FX-DCS-G1-EHS-KIT20 4052899452206 20 x endcap, 1 x glue (25g)
Silicone glue 25 g FX-DCS-G1-GL-25 4052899452244 1 x glue (25g)
CONNECTsystem Diffuse for LINEARlight Flex Diffuse SIDE
Product type Product description Product code (EAN 10) Package content (EAN 10)
Mounting bracket for aluminum profile FX-QMS-G1-BMZI-DIV1 4052899446861 40 x mounting bracket
Mounting bracket FX-LFDM-G1-BT-17H11 4052899452480 50 x mounting bracket
Mounting bracket with additional wing FX-LFDM-G1-BTL-17H11E9 4052899452510 50 x mounting bracket
Aluminum profile TOP FX-LFDM -G1-TT-16H16-200 4052899544949 5 x profile
Aluminum profile TOP wings FX-LFDM -G1-TTL-16H11W10-200 4052899544963 5 x profile
Diffuse mounting system: Brackets and aluminum profiles for LINEARlight Flex Diffuse TOP
Product type Product description Product code (EAN 10) Package content (EAN 10)
Mounting bracket for aluminum profile FX-QMS-G1-BMZI-DIV1 4052899446861 40 x mounting bracket
Mounting bracket FX-LFDM-G1-BS-12H13 4052899452541 50 x mounting bracket
Mounting bracket with additional wing FX-LFDM-G1-BSL-12H13E9 4052899452572 50 x mounting bracket
Aluminum profile SIDE FX-LFDM-G1-TS-16H16-200 4052899544925 5 x profile
Steel profile bendable SIDE FX-LFDM-BEND-1000 KIT 3 PCS 4062172192583 3 x profile
Diffuse mounting system: Brackets and aluminum/steel profiles for LINEARlight Flex Diffuse SIDE
4 Flexessories
To support the installation of Flex LED strips, a whole range of Flexessories – dedicated accessories for
Flex LED strips – is available. Our new extended range of Flexessories facilitates a quick and easy installation.
LINEARlight Flex Diffuse (LFD) | Flexessories
www.osram.com/flex
OSRAM GmbH
Head office:
Marcel-Breuer-Strasse 6
80807 Munich, Germany
Phone +49 89 6213-0
Fax +49 89 6213-2020
www.osram.com
Symbols
Color temperature in K
Voltage in V
Color
Wavelength
Nominal wattage per meter in W
Luminous flux per meter
Energy efficiency class
Luminous efficacy
No. of LEDs per meter
Length l in mm
Minimal length l in mm
Width w in mm
Heigth h in mm
10/22 Subject to change without notice. Errors and omissions excepted.
Disclaimer
All information contained in this document has been collected,
analyzed and verified with great care by OSRAM. However,
OSRAM GmbH is not responsible for the correctness and
completeness of the information contained in this document
and OSRAM GmbH cannot be made liable for any damage
that occurs in connection with the use of and/or reliance on
the content of this document. The information contained in
this document reflects the current state of knowledge on
the date of issue.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Osram LINEARlight Flex Diffuse User guide

LINEARlight Flex Diffuse
Osram
Brand
Osram
Model
LINEARlight Flex Diffuse
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents