Delta T14400-T2O Installation guide

Delta Faucet Company

Product Service

55 E. 111th Street

Indianapolis, IN 46280

MultiChoice

®

Valve Trim

Installation Instructions

Owners Manual

14 T20

Series

Write purchased model number here.

Table of Contents:

Warranty ............................................................................. Page 2

MultiChoice

®

Rough-In Installation Instructions ...................Pages 3 - 5

14 T20 Series Installation Instructions ................................ Pages 6 - 10

Maintenance ....................................................................... Page 11

To order replacement parts, visit www.deltafaucet.com

1

You May Need

T

E

F

L

O

N

10/2/15

79061 Rev. C

CAUTION: This system/device must be set by the

installer to ensure safe, maximum temperature.

Any change in the setting may raise the discharge

temperature above the limit considered safe and

may lead to hot water burns.

NOTICE TO INSTALLER: CAUTION!–As the

installer of this valve, it is your responsibility

to properly INSTALL and ADJUST this valve

per the instructions given. This valve does

not automatically adjust for inlet temperature

changes, therefore, someone must make the

necessary Rotational Limit Stop or temperature

knob adjustments at the time of installation

and further adjustments may be necessary

due to seasonal water temperature change.

YOU MUST inform the owner/user of this

requirement by following the instructions. If you

or the owner/user are unsure how to properly make

these adjustments, please refer to page 10, and if

still uncertain, call us at 1-800-345-DELTA.

After installation and adjustment, you must afﬁx

your name, company name and the date you

adjusted the Rotational Limit Stop or temperature

knob to the caution label provided and apply or

attach the label to the back side of the closest

cabinet door and the warning label to the water

heater. Leave this Instruction Sheet for the

owner’s/user’s reference.

WARNING: This pressure balanced or

thermostatic bath valve is designed

to minimize the effects of outlet water

temperature changes due to inlet pressure

changes, commonly caused by dishwashers,

washing machines, toilets and the like. It may

not provide protection from hot water burns

when there is a failure of other temperature

controlling devices elsewhere in the

plumbing system, if the rotational limit stop

or temperature knob is not properly set or if

the hot water temperature is changed after the

settings are made or if the water inlet changes

due to seasonal changes.

WARNING: Do not install a shut-off device on

either outlet of this valve. When this type of

device shuts off the water ﬂow, it can defeat

the ability of the valve to balance the hot and

cold water pressures.

79061

14 T20 Series14 T20 Series14 T20 Series

2

Parts and Finish

All parts (other than electronic parts and batteries) and finishes of this Delta

®

faucet are warranted to the original

consumer purchaser to be free from defects in material and workmanship for as long as the original consumer

purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the

date of purchase.

Electronic Parts and Batteries (if applicable)

Electronic parts (other than batteries), if any, of this Delta

®

faucet are warranted to the original consumer

purchaser to be free from defects in material and workmanship for 5 years from the date of purchase or, for

commercial users, for one year from the date of purchase. No warranty is provided on batteries.

Delta Faucet Company will replace, FREE OF CHARGE, during the applicable warranty period, any part or

finish that proves defective in material and/or workmanship under normal installation, use and service. If repair

or replacement is not practical, Delta Faucet Company may elect to refund the purchase price in exchange for

the return of the product. These are your exclusive remedies.

Delta Faucet Company recommends using a professional plumber for all installation and repair. We also

recommend that you use only genuine Delta

®

replacement parts.

Delta Faucet Company shall not be liable for any damage to the faucet resulting from misuse, abuse, neglect

or improper or incorrectly performed installation, maintenance or repair, including failure to follow the applicable

care and cleaning instructions.

Replacement parts may be obtained by calling the applicable number below or by writing to:

In the United States and Mexico: In Canada:

Delta Faucet Company Masco Canada Limited, Plumbing Group

Product Service Technical Service Centre

55 E. 111th Street 350 South Edgeware Road

Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1

1-800-345-DELTA (3358) 1-800-345-DELTA (3358)

[email protected] [email protected]

Proof of purchase (original sales receipt) from the original purchaser must be made available to Delta Faucet

Company for all warranty claims unless the purchaser has registered the product with Delta Faucet Company.

This warranty applies only to Delta

®

faucets manufactured after January 1, 1995 and installed in the United

States of America, Canada and Mexico.

DELTA FAUCET COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING LABOR CHARGES) FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY

ON THE FAUCET. Some states/provinces do not allow the exclusion or limitation of special, incidental or

consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you

special legal rights. You may also have other rights which vary from state/province to state/province.

This is Delta Faucet Company’s exclusive written warranty and the warranty is not transferable.

If you have any questions or concerns regarding our warranty, please view our Warranty FAQs at www.

deltafaucet.com, email us at [email protected] or call us at the applicable number above.

Limited Warranty on Delta

®

Faucets

SHUT OFF WATER SUPPLIES.

Consider the type and thickness of your

finished wall before placing your stringer

back plate. Install the body (1) so the

surface of the finished wall is flush with the

front of the plasterguard (2) ± 3/8". Note:

For models with stops (3), plasterguard

MultiChoice

®

Rough-In Installation

1

A.

B.

Distance (1) from the stringer (2) to the

front of the plasterguard is 2.8" (71 mm).

Distance (3) from the stringer (2) to the

front of the bonnet is 3.9" (99 mm).

must be flush or subflush 3/8" to

finished wall. Mount body using the two

stringer mounting holes (4) on the bracket.

Note: Remove cover (5) to access

mounting holes. Make sure the word

“UP” (6) is on top of the valve body when

installing.

If a thin wall is used, be sure to have the

plasterguard behind the wall, otherwise

the wall should always be flush with the

front of the plasterguard. See instruction

on the bag for thin wall mounting.

1

2

6

5

4

1

3

2

3

Connect valve body to water supplies using

the proper fittings for your valve body type

(copper tubing, iron pipe or Pex). Note: (1) is

the cold inlet port and (2) is the hot inlet

port. If either of the two outlet ports is to be

unused, seal the port with a pipe plug.

Remove bonnet (1). Warning: Avoid

soldering at high temperatures.

Be sure stops (2) are removed from the

w/stops version before soldering. (Do not

install stops before soldering.)

If you are making a back to back or

reverse installation (hot on right and

cold on left) install the valve body as

described, but the water supply lines will

be reversed. Note: (1) is the hot inlet

port and (2) is the cold inlet port.

Copper Tubing Iron Pipe

Pex

C.

1

2

1

2

1

2

MultiChoice

®

Rough-In Installation

4

D.

1

2

Connect top outlet (1) to shower pipe with

proper fittings. Connect bottom outlet (2) to tub

spout pipe with proper fittings. Pipe (3) between

valve body and tub spout must be a minimum of

1/2" (13 mm) copper pipe or 1/2" (13 mm) iron

pipe in a straight drop no less than 8" (203 mm)

but no more than 18" (457 mm) long with only

one iron pipe or copper 90 degree elbow to the

tub spout nipple. Do not use PEX tubing for

tub spout drop.

Prior to testing, remove cover (1) and bonnet

nut (2). Insert cartridge and tighten bonnet nut.

Turn cartridge stem counter clockwise until it will

no longer rotate. Plug both outlets with proper

fittings. Check for leaks. After testing, remove

cartridge, shower and/or tub spout plug and

flush system by slowly turning on water supply

to purge valve system of debris. After flushing,

reinstall cartridge (see page 6), bonnet nut

and cover. Install stops (3 & 4) in the models

with stops and set to full open. Note: Install

stops as follows: Thread nut (3) onto stem

(4) as shown. Then press stem and nut

assembly into body and tighten using a 3/8",

6 point, deep well socket. With a flat head

screwdriver, adjust stem clockwise to close

and counterclockwise to open.

E.

F.

MultiChoice

®

Rough-In Installation

1

2

3

PRESSURE TESTING & FLUSHING THE INSTALLATION

1

2

1

2

4

3

5

3

4

14 T20 Series Installation

2

Cartridge Installation

C.

Turn off water supplies. Remove

cover (1) and bonnet nut (2) from the

body, if necessary. If this is not a thin

wall mounting, the entire plasterguard (3)

may be removed.

For back to back or reverse installations

(hot on right and cold on left) insert the

cartridge with the ‘C’ on the left. If you

are not making a reverse or back to back

installation skip this step and continue

with step 2C.

Slide bonnet nut (1) over the wire and car-

tridge (2) and thread onto the body. Hand

tighten securely. Note: After bonnet nut

is installed, verify the valve is in the off

position. Rotate stem clockwise.

B.

Back to back Installation

Normal Installation (changes not required)

Reverse

Installation

Cold

Hot

1

4

3

1

6

A.

1

2

3

Rotate the cartridge (1) so the letter ‘C’

(2) appears on the right. Insert cartridge

into valve body as shown. Make sure

the cartridge tubes and O-rings (3) are

properly seated in holes at the base of the

body. Ensure the keys on the body are fully

engaged with the slots in the body (4).

2

14 T20 Series Installation

A.

B.

If your model requires a spacer (1), insert

it into the sleeve (2) and push it to the

front. Slide the sleeve over the cartridge,

body and O-ring. Caution: Do not

damage the wire during installation

of the sleeve.

1

2

1

2

Slide O-ring (1) over cartridge, wire and

the bonnet nut (2). The O-ring, which acts

as a spacer to steady the sleeve, should

rest behind the bonnet nut.

1

3

F

C

C.

D.

Mount the backplate onto body using

screws (1) provided. Do not over

tighten screws.

1

2

Connect wire from cartridge (1) to back

side of backplate (2). Note: Switch (3) is

used to change the temperature from

Celsius to Fahrenheit.

F

C

3

7

Backplate and Trim Installation

14 T20 Series Installation

G.

H.

Secure the escutcheon (1) by aligning the

4 tabs (2) with the 4 slots (3) in the back-

plate. Engage all 4 tabs fully into the slots

and rotate clockwise to lock.

Using an Allen wrench to secure the set

screw, install the handle onto the stem.

Note: If no set screw hole - handle may

have cap with screw.

1

2

3

Backplate and Trim Installation

E.

Remove battery cover (1) by pushing in the

direction of the arrow. Insert 3 “AAA”

batteries (2) making sure to orient in

proper direction.

1

2

8

F.

If shower wall is uneven, please seal back-

plate to the wall with silicone to prevent

moisture access to the electronics.

14 T20 Series Installation

4

Showerhead and Tub Spout Installation

FOR SHOWERHEAD INSTALLATION:

Connect top outlet (1) to shower arm (2)

with proper ﬁttings. To prevent damage

to ﬁnish on shower arm, insert wall end

of shower arm into shower ﬂange (3)

before screwing arm into riser connection.

Thread showerhead (4) onto shower

arm. Apply plumber tape to pipe threads

on both ends. Do not overtighten

showerhead.

A.

3

2

1

Slip-On Installation

The copper tube (1) must be 1/2” nominal

copper. Important: If it is necessary to cut

the copper tube, the end must be cham-

fered free of burrs to prevent cutting or

nicking O-ring inside the spout. Slide spout

over copper tube ﬂush with the ﬁnished tub

or wall surface. Tighten set screw (2), but

do not overtighten.

4

1

9

FOR TUB SPOUT INSTALLATION:

Refer to the installation instructions supplied with your spout. Do not connect deck mount

spouts to in-wall valves. Do not use hand showers connected in lieu of a tub spout to a

tub/shower valve. Do not use PEX tubing for tub spout drop.

B-1

B-2

B-3

Iron Pipe Installation

Install threaded pipe nipple (1) to extend

past ﬁnished wall. Apply plumber tape to

threads on pipe nipple and screw on

tub spout.

Copper Sweat Installation

Remove O-ring (1) from adapter (2). Solder

adapter to tube taking care to keep solder

away from O-ring groove. CAUTION: NO

SOLDER PERMITTED ON OUTSIDE

DIAMETER OF ADAPTER ADJACENT

TO O-RING GROOVE. Cut off tube (3) and

replace O-ring on groove of brass adapter.

Thread tub/spout onto adapter, taking care

not to damage O-ring, and hand tighten until

spout is ﬁrmly against ﬁnished wall and all

slack is taken up behind wall.

2

1

2

3

13 / 14 Series Installation

10

14 T20 Series Installation

5

Adjusting the Rotational Limit Stop

IMPORTANT:

The Rotational Limit Stop is used to limit the

amount of hot water available such that, if set

properly, the user will not be scalded if the han-

dle accidentally is rotated all the way to “hot”

when a person is showering or ﬁlling a tub. The

ﬁrst position allows the LEAST amount of hot

water to mix with the cold water in the system.

In the ﬁrst position the water will be the coldest

possible when the handle is turned all the way

to hot. As you move the Rotational Limit Stop

clockwise, you progressively add more and

more hot water in the mix. The last position will

result in the greatest amount of hot water to

the mix, and the greatest risk of scald injury if

someone accidentally turns the valve handle

all the way to the hot side while showering or

ﬁlling a tub.

WARNING: In some instances, setting the

Rotational Limit Stop in the hottest position

(full clockwise) could result in scald injury.

It is necessary to adjust the Rotational

Limit Stop so that the water coming out

of the valve will not scald the user when

the handle of the valve is rotated to the

hot side.

• According to the majority of industry stan-

dards, the maximum allowable temperature of

the water exiting the valve is 120°F (Your local

plumbing codes may require a water tempera-

ture less than 120°F).

• The Rotational Limit Stop may need to be re-

adjusted seasonally if the inlet water tempera-

ture changes. For example, during the winter,

the cold water temperature is colder than it is

during the summer which could result in vary-

ing outlet temperatures. A water temperature

for a comfortable bath or shower is typically

between 90°F - 110°F.

• Use a thermometer to set the rotational limit

stop. Do not rely on the digital display tempera-

ture. There may be up to a 7° F difference in

temperature of the water coming out of the

spout or showerhead as compared to the

reading on the display.

• Run the water so that the cold water is as

cold as it will get and hot water is as hot as

it will get. Place the handle on the stem and

rotate the handle counterclockwise until the

handle stops.

• Place a thermometer in a plastic tumbler

and hold in the water stream. If the water

temperature is above 120°F, the Rotational

Limit Stop must be repositioned

counterclockwise to decrease valve outlet

water temperature to be less than 120°F

or to meet the requirements of your local

plumbing codes.

• To adjust the temperature of the water

coming out of the valve, remove the o-ring

and pull the disc back to a position where it is

possible to remove the Rotational Limit Stop

and readjust the teeth engagement position to

the desired temperature. Counterclockwise will

decrease the outlet temperature, clockwise will

increase the outlet temperature. Temperature

change per tooth (notch) could be 4° - 16°F

based on inlet water conditions. Repeat as

necessary. Push disc until fully seated and

replace o-ring.

WARNING: Failure to re-install disc and

o-ring after setting Rotational Limit Stop

could result in scald injury.

• MAKE SURE COLD WATER FLOWS

FROM THE VALVE FIRST. MAKE SURE

WATER FLOWING FROM THE VALVE

AT THE HOTTEST FLOW POSSIBLE

DOES NOT EXCEED 120°F OR THE

MAXIMUM ALLOWED BY YOUR LOCAL

PLUMBING CODE.

Rotational Limit Stop

Stem

Disc

Faucet leaks from tub spout/showerhead:

SHUT OFF WATER SUPPLIES.

Replace valve cartridge EP78407. Check condition

of lower O-rings and replace if necessary RP14414.

See Helpful Hints 1, 2, & 3.

If leak persists:

SHUT OFF WATER SUPPLIES.

Replace valve cartridge EP78407.

See Helpful Hints 1, 2, 3 & 5.

Unable to maintain constant water temperature:

Replace valve cartridge EP78407 or follow

instructions in Helpful Hints 1, 2, 4 & 5.

Helpful Hints:

1. Before removing valve cartridge assembly for any

maintenance, be sure to note the position of the

rotational limit stop on the cap. The valve cartridge

assembly must always be put back in the same

position. BE SAFE! After you have ﬁnished the

installation, turn on valve to make sure COLD WATER

FLOWS FIRST.

2. To remove valve cartridge from body, shut off

water supplies and remove handle and bonnet

nut. Do not pry the valve cartridge out of the body

with a screwdriver. Place handle on stem and rotate

counterclockwise approximately 1/4 turn after the stop

has been contacted. Lift valve cartridge out of body.

3. To remove seats and springs, remove valve

cartridge. Separate cap assembly from the

housing assembly by rotating the cap assembly

counterclockwise 90

o

(degrees). Separate cap and

housing assemblies. Remove seats and springs and

replace. Place the largest diameter of the spring

into the seat pocket ﬁrst and then press the tapered

end of the seal over the spring. Reassemble valve

cartridge and replace in body following instructions

given in 1 above.

4. If the water in your area has lime, rust, sand or

other contaminants in it, your pressure balance

valve will require periodic inspection. The frequency

of the inspection will depend on the amount of

contaminants in the water. To inspect valve cartridge

remove it and follow the steps in note 1 above.

Turn the valve to the full mix position and shake the

cartridge vigorously. If there is a rattling sound, the

unit is functional and can be reinstalled following

instructions given in note 1 above. If there is no rattle,

replace valve cartridge EP78407.

5. Push disc until fully seated. See page 10 for

more details.

To order replacement parts, visit

www.deltafaucet.com or call

1-800-345-DELTA (3358)

14 T20 Series Maintenance

11

Cleaning and Care

Care should be given to the cleaning of this prod-

uct. Although its ﬁnish is extremely durable, it can

be damaged by harsh abrasives or polish. To clean,

simply wipe gently with a damp cloth and blot dry

with a soft towel.

Warning: Scrubbing Bubbles

®

Bathroom Cleaner

and Lysol

®

Basin Tub and Tile Cleaner must not be

used on the clear knob handles and levers. Use of

these cleaners can result in cracked or severely

damaged handles. If overspray gets onto the

handles, immediately wipe them dry with a soft

cotton cloth

Remove the escutcheon (1) by rotating it

counterclockwise until it can be pulled from the

backplate. Carefully, slide the escutcheon over the

sleeve and remove.

Remove battery cover (1) by pushing in the direc-

tion of the arrow. Remove old batteries and insert

3 new “AAA” batteries (2) making sure to orient in

proper direction. Reinstall parts in reverse order.

B.

C.

1

2

To change batteries:

Using an Allen wrench to loosen the set screw (1),

remove the handle from the stem. Note: If no set

screw hole - handle may have cap with screw.

A.

1

Page is loading ...

Delta T14400-T2O Installation guide

Delta T14400-T2O Installation guide

in other languages

Related papers

Other documents