OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
JobMax
™
POWER BASE
BASE POUR ENTRAÎNEMENT
JobMax
™
BASE DE ALIMENTACIÓN
JobMax
™
R2851
To register your RIDGID
product, please visit:
http://register.RIDGID.com
Pour enregistrer votre
produit de RIDGID,
s’il vous plaît la visite:
http://register.RIDGID.com
Para registrar su producto
de RIDGID, por favor visita:
http://register.RIDGID.com
WARNING:
To reduce the risk of injury, the
user must read and understand
the operator’s manual before
using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
ADVERTENCIA:
Para reducir el riesgo de lesiones,
el usuario debe leer y comprender
el manual del operador antes de
usar este producto.
AVERTISSEMENT :
Pour réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation
avant d’employer ce produit.
TABLE OF CONTENTS
****************
General Power Tool
Safety Warnings ..............................2-3
Power Base Safety Warnings ............. 3
Symbols ..............................................4
Electrical ............................................. 5
Assembly ............................................ 6
Operation ............................................6
Maintenance ....................................... 7
Illustrations .........................................8
Parts Ordering and
Service ................................Back page
TABLE DES MATIÈRES
****************
Avertissements de sécurité générales
relatives aux outils électriques ........2-3
Avertissements de sécurité relatifs
base pour entraînement ..................... 3
Symboles ............................................4
Caractéristiques électriques ...............5
Assemblage ........................................6
Utilisation ........................................6-7
Entretien .............................................7
Illustrations .........................................8
Commande de pièces et
dépannage ........................Page arrière
ÍNDICE DE CONTENIDO
****************
Advertencias de seguridad
para herramientas eléctricas ......... 2-3
Advertencias de seguridad
de base de alimentación ...................3
Símbolos ............................................4
Aspectos eléctricos ............................ 5
Armado ..............................................6
Funcionamiento ............................. 6-7
Mantenimiento ...................................7
Illustraciones ......................................8
Pedidos de piezas y
servicio .........................Pág. posterior
2 - English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is un-
avoidable, use a ground fault circuit interrupter (GFCI)
protected supply. Use of a GFCI reduces the risk of
electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
3 - English
POWER BASE SAFETY WARNINGS
Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Always wear eye protection with side shields marked
to comply with ANSI Z87.1 when assembling parts,
operating the tool, or performing maintenance. Fol-
lowing this rule will reduce the risk of serious personal
injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest authorized service center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
Make sure your extension cord is in good condi-
tion. When using an extension cord, be sure to use
one heavy enough to carry the current your product
will draw. A wire gauge size (A.W.G.) of at least 16 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 100 feet is not recom-
mended. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
If the power supply cord is damaged, it must be re-
placed only by the manufacturer or by an authorized
service center to avoid risk.
Do not attempt to modify this product or create ac-
cessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
Do not attempt to use the handle without an accessory
head installed. Doing so could result in serious personal
injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this product. If
you loan someone this product, loan them these instruc-
tions also.
Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
When servicing a power tool, use only identical re-
placement parts. Follow instructions in the Mainte-
nance section of this manual. Use of unauthorized parts
or failure to follow Maintenance instructions may create
a risk of shock or injury.
GENERAL POWER TOOL SAFETY WARNINGS
4 - English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper in-
terpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand operator’s
manual before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply with
ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any hot
surface.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
Direct Current Type or a characteristic of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates important information not related to an injury hazard,
such as a situation that may result in property damage.
CALIFORNIA PROPOSITION 65
WARNING:
This product may contain chemicals, including lead, known to the State of California to cause cancer, birth defects
or other reproductive harm. Wash hands after handling.
5 - English
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protecting
insulation. Double insulated tools do not need to be
grounded.
WARNING:
The double insulated system is intended to protect
the user from shock resulting from a break in the
product’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, AC only
(normal household current), 60 Hz. Do not operate this
tool on direct current (DC). A substantial voltage drop will
cause a loss of power and the motor will overheat. If your
tool does not operate when plugged into an outlet, double-
check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
When working outdoors with a tool, use an extension
cord that is designed for outside use. This type of cord is
designated with “W-A” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
**Ampere rating (on tool data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 —
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use tool with
a damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
ELECTRICAL
6 - English
To turn the tool ON, depress the switch trigger. To turn it
OFF, release the switch trigger and allow the tool to come
to a complete stop. The trigger will not operate the power
base unless an accessory head is attached.
NOTE: A whistling or ringing noise coming from the switch
during use is a normal part of the switch function.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 1, page 8.
Set the direction of rotation selector in the OFF (center lock)
position to lock the switch trigger and help prevent accidental
starting when not in use.
Position the direction of rotation selector to the left of the
switch trigger for forward movement. Position the selector
to the right of the switch trigger for reverse movement.
NOTE: The tool will not run unless the direction of rotation
selector is pushed fully to the left or right.
NOTICE:
To prevent gear damage, always allow the tool
to come to a complete stop before changing the
direction of rotation.
INSTALLING/REMOVING ACCESSORY HEAD
See Figure 2, page 8.
Disconnect the power base from the power supply.
Depress the latches on both sides of the power base with
one hand while pulling the head away from the tool with
your other hand.
Place the desired accessory head on the power base and
push until the latches click into position. Pull on the head
to make sure it is securely installed before operation.
NOTE: The head can be installed at 90° angles to best
suit your application needs.
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes, resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Numerous applications are available depending upon the
accessory installed. Refer to the operator’s manual for
the accessory head to determine available applications
while using that head.
Avoid running the tool at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the tool to become overheated. If this occurs, cool the
tool by running it without a load and at full speed.
LED LIGHT
See Figure 1, page 8.
The LED light, located above the switch trigger, illuminates
when the switch trigger is depressed. This provides extra
light for increased visibility.
VARIABLE SPEED SWITCH TRIGGER
See Figure 1, page 8.
The variable speed switch trigger delivers higher speed with
increased trigger pressure and lower speed with decreased
trigger pressure.
OPERATION
ASSEMBLY
WARNING:
Do not use this product if it is not completely
assembled or if any parts appear to be missing or
damaged. Use of a product that is not properly and
completely assembled or with damaged or missing
parts could result in serious personal injury.
If any parts are damaged or missing, please call 1-866-539-1710 for assistance.
WARNING:
Do not attempt to modify this product or create
accessories or attachments not recommended
for use with this product. Any such alteration
or modification is misuse and could result in a
hazardous condition leading to possible serious
personal injury.
7 - English
WARNING:
Before inspecting, cleaning, or performing any
maintenance, make sure the direction of rotation
switch is in the center lock position, wait for all
moving parts to stop, and disconnect from the
power supply. Failure to follow these instructions
can result in death, serious personal injury, or
property damage.
WARNING:
When servicing use only identical replacement
parts. Use of any other parts may create a hazard
or cause product damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
MAINTENANCE
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
POWER SUPPLY CORD REPLACEMENT
If replacement of the power supply cord is necessary, this
must be done by an authorized service center in order to
avoid a safety hazard.
REPLACING THE DRIVE GEAR COVER
See Figure 3, page 8.
If over time you notice the noise of the tool getting louder
than usual, check the condition of the drive gear cover. If the
cap is excessively damaged so that the metal gear is clearly
visible, remove it and replace with the spare cap included.
NOTE: To reduce the noise level of the tool, do not operate
without the drive gear cover installed.
NOTE: ILLUSTRATIONS START ON PAGE 8
AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.
This product has a 90-Day Satisfaction Guarantee Policy, as well as a Three-year Limited Warranty.
For Warranty and Policy details, please go to www.RIDGID.com
or call (toll free) 1-866-539-1710.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
JobMax
™
POWER BASE
BASE POUR ENTRAÎNEMENT JobMax
™
BASE DE ALIMENTACIÓN JobMax
™
R2851
991000423
6-26-15 (REV:01)
ONE WORLD TECHNOLOGIES, INC.
P.O. Box 35, Hwy. 8
Pickens, SC 29671, USA
1-866-539-1710 www.RIDGID.com
RIDGID is a registered trademark of RIDGID, Inc., used under license.
Customer Service Information:
For parts or service, do not return this product to the store. Contact your nearest
RIDGID
®
authorized service center. Be sure to provide all relevant information when
you call or visit. For the location of the authorized service center nearest you, please
call 1-866-539-1710 or visit us online at www.RIDGID.com.
MODEL NO. ____________________SERIAL NO._______________________________
Service après-vente :
Pour acheter des pièces ou pour un dépannage, ne pas retourner ce produit au
magasin. Contacter le centre de réparations RIDGID
®
agréé le plus proche. Veiller à
fournir toutes les informations pertinentes lors de tout appel téléphonique ou visite.
Pour obtenir l’adresse du centre de réparations agréé le plus proche, téléphoner au
1-866-539-1710 ou visiter notre site www.RIDGID.com.
NO. DE MODÈLE _______________ NO. DE SÉRIE _____________________________
Información sobre servicio al consumidor:
Para piezas de repuesto o servicio, no devuelva este producto a la tienda. Comuníquese
con el centro de servicio autorizado de productos RIDGID
®
de su preferencia.
Asegúrese de proporcionar todos los datos pertinentes al llamar o al presentarse
personalmente. Para obtener información sobre el centro de servicio autorizado más
cercano a usted, le suplicamos llamar al 1-866-539-1710 o visitar nuestro sitio en la
red mundial, en la dirección www.RIDGID.com.
NÚM. DE MODELO _____________ NÚM. DE SERIE ___________________________
JobMax
™
Multi-Tool Head
R8223406
Use only with base model Series A, B, C, D, E
• Series A includes models R8223400, R8223500
• Series B includes model R2850, R2851
• Series C includes model R9020PN
• Series D includes model P246
• Series E includes model R8620
To register your RIDGID product, please visit: http://register.RIDGID.com
WARNING:
To reduce the risk of injury, user must read and understand this operator’s
manual as well as the operator’s manual for the power base and, if applicable,
the battery pack and charger before use. Ensure compatibility and proper fit
of head and power base before using.
SPECIFIC SAFETY RULES
Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body leaves it unstable
and may lead to loss of control.
To reduce the risk of electrocution or electric shock, do not touch exposed
metal parts of multi-tool head or power base during operation. For proper hand
placement, refer to the operator’s manual included with your power base.
PRODUCT SPECIFICATIONS
Speed ............................................................................ 0-20,000 oscillations per min.
APPLICATIONS
Accessory Type Uses
Segment saw
blade
Flush cutting in wood, drywall, and
plastic.
Wood plunge
cutting blade
Straight cutting in wood, drywall, and
plastic.
Detail sanding
backing pad
Sanding in corners and other hard-to-
reach areas
Sanding sheets
Sanding sheets in 60 grit (1), 80 grit (3),
and 120 grit (1) are provided for sanding
in different applications
Adaptor
Install adaptor with either side out for use
with different brands of accessories.
INSTALLING HEAD
See Figure 1.
Remove the battery pack from the power base or disconnect from power supply.
Place the head on the power base and push until the latches click into position.
Pull on the head to make sure it is securely installed before proceeding.
NOTE: The head can be installed at 90° angles to best suit your application needs.
WARNING:
The accessory clamp on this tool may create a pinch point hazard, handle
with care. Keep fingers away from accessory clamp when rotating the sliding
lever into the “locked position”.
INSTALLING ACCESSORIES
See Figures 2 - 6.
Remove the battery pack from the power base or disconnect from power supply.
Pull the sliding lever up until the arrow on the sliding lever is aligned with the arrow
on the housing and then, pull it fully back so that it is resting on the back of the
housing to unlock the accessory clamp.
Pivot the accessory clamp until it is in line with the clamp shaft.
Place the desired accessory on the head so that the openings on the accessory fit
on the raised parts of the head. Pivot the accessory clamp until it is perpendicular
to the clamp shaft.
NOTE: Some other brands of accessories will also fit this head without the use of
adaptors. When using these accessories, always follow the instructions for that
accessory, in addition to all instructions for this product.
An adaptor is provided to allow use of some other brands of accessories with the
power base. When using these accessories, install the adaptor first, then install
the accessory. The adaptor has a different interface pattern on each side for use
with different brands of accessories. Only use the adaptor when using these
accessories.
NOTE: When using other brands of accessories that require the use of an adaptor,
always follow the instructions for these accessories, in addition to all instructions
for this product.
With the accessory in place, push the sliding lever forward and then down to lock
the accessory clamp in place.
WARNING:
Do not wear loose clothing or jewelry when operating tool. They could get
caught in moving parts causing serious injury. Keep head away from tool and
work area. Hair could be drawn into tool causing serious injury.
WARNING:
Unsecured work could be thrown towards the operator causing injury.
CUTTING
See Figure 7.
Hold the tool firmly in front of and clearly away from you. Make sure blade is clear
of any foreign material.
Mark the line of cut clearly.
Depress the switch trigger to start the cutting action. Allow the blade to reach your
desired speed, then move the blade into the work.
To cut, keep the teeth of the blade in the work surface and move the back of the
tool slowly in a constant sideways motion.
NOTE: If the writing on the blade looks blurry when in use, you are using the correct
amount of pressure. If they become clear, you are using too much force.
NOTICE:
Do not force. Use only enough pressure to keep the tool cutting. Let the blade
and tool do the work. Use of excessive pressure will cause strong vibrations
to the tool, which may result in broken blades and cause premature wear to
the tool’s motor.
WARNING:
Keep hands away from blades. Do not reach underneath work or around or
over the blade while blade is moving. Do not attempt to remove cut material
when blade is moving.
SANDPAPER SELECTION
Selecting the correct size grit and type sandpaper is an extremely important step in
achieving a high quality sanded finish. Aluminum oxide, silicon carbide, and other
synthetic abrasives are best for power sanding. Natural abrasives, such as flint and
garnet are too soft for economical use in power sanding.
In general, coarse grit will remove the most material and finer grit will produce the
best finish in all sanding operations. The condition of the surface to be sanded will
determine which grit will do the job. If the surface is rough, start with a coarse grit and
sand until the surface is uniform. Medium grit may then be used to remove scratches
left by the coarser grit and finer grit used for finishing of the surface. Always continue
sanding with each grit until surface is uniform.
SANDING
See Figure 8.
Hold tool in front and away from you, keeping it clear of the workpiece. Start tool and
let the motor build to your desired speed, then gradually lower on the work with a slight
forward movement. Move the tool slowly over workpiece using forward and backward
or side to side strokes. Upon completion of sanding operation, always remove sander
from workpiece before turning it off.
D n frce The weight of the unit supplies adequate pressure, so let the sandpaper
and sander do the work. Applying additional pressure only slows the motor, rapidly
wears sandpaper, and greatly reduces sander speed. Excessive pressure will overload
the motor causing possible damage from motor overheating and can result in inferior
work. Any finish or resin on wood may soften from the frictional heat. Do not allow
sanding on one spot too long as sander’s rapid action may remove too much material,
making the surface uneven.
CALIFORNIA PROPOSITION 65
WARNING:
This product and some dust created by power sanding, sawing, grinding,
drilling, and other construction activities may contain chemicals, including
lead, known to the State of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products and,
• arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often
you do this type of work. To reduce your exposure, work in a well-ventilated
area and with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Fig. 1
Fig. 4
Fig. 2
Fig. 3
Fig. 6
Fig. 7
Fig. 8
Fig. 5
A - Multi-tool head (tête polyvalente, cabezal para
varias herramientas)
B - Latches (loquets, broche)
C - Power base (base pour entraînement, base de
alimentación)
A - Clamp (bride, prensa)
B - Adaptor (adaptateur, adaptador)
C - Generic accessory (accessoire générique,
accesorio genérico)
A - Detail sanding backing pad (plateau porte-
disque abrasif de finition, almohadilla de
respaldo para lijado detallado)
B - Wood plunge cutting blade (lame de coupe
plongeante pour bois, hoja para cortes de
penetración para madera)
C - Segment saw blade (lame de scie segmentaire,
hoja de sierra segmentada)
A - Sliding lever (levier de coulissant, palanca de
deslizable)
B - Arrow (flèche, flecha)
C - Accessory clamp (bride pour accessoire,
abrazadera de accesorios)
A - Accessory clamp (bride pour accessoire,
abrazadera de accesorios)
B - Clamp shaft (arbre de la bride, eje de la
abrazadera)
A - Sliding Lever (levier de coulissant,palanca de
deslizable)
B - Accessory clamp (bride pour accessoire,
abrazadera de accesorios)
FRANÇAIS
Tête polyvalente JobMax
™
R8223406
Compatible uniquement avec le base modèle de série A, B, C, D, E
• Série A inclut modèle R8223400, R8223500
• Série B inclut modèle R2850, R2851
• Série C inclut modèle R9020PN
• Série D inclut modèle P246
• Série E inclut modèle R8620
Pour enregistrer votre produit de RIDGID, s’il vous plaît la visite:
http://register.RIDGID.com
AVERTISSEMENT :
Pour réduire les risques de blessure, l’utilisateur doit lire et comprendre le
présent manuel d’utilisation ainsi que le manuel d’utilisation pour la base
pour entraînement et, si applicable, du bloc-piles et du chargeur avant de les
utiliser. S’assurer que la tête et la base pour entraînement sont compatibles
et qu’elles sont installées de la façon appropriée avant de les utiliser.
RÈGLES DE SÉCURITÉ PARTICULIÈRES
Lorsque l’outil est utilisé pour un travail risquant de le mettre en contact avec
des fils électriques cachés ou son propre cordon d’alimentation, le tenir par
les surfaces de prise isolées. Le fait de couper un fil sous tension « électrifie »
les pièces métalliques exposées de l’outil et pourrait donner l’opérateur de choc
électrique.
Utiliser des serre-joints ou un autre système approprié pour maintenir
fermement la pièce sur une surface stable. Une pièce tenue à la main ou contre
son corps est instable et peut causer une perte de contrôle.
Pour réduire le risque d’électrocution ou choc électrique, ne pas toucher les
pièces métalliques exposées de tête polyvalente ou base pour entraînement
pendant le fonctionnement. Consulter le manuel d’utilisation du base afin de
connaître l’emplacement de la main adéquat.
FICHE TECHNIQUE
Vitesse .....................................................................0 à 20 000 oscillations par minute
APPLICATIONS
Type d’accessoire Utilisations
Lame de scie
segmentaire
Pour les applications de coupe à ras dans
le bois, la cloison sèche et le plastique
Lame de coupe
plongeante pour
bois
Pour effectuer des coupes droites dans le
bois, la cloison sèche et le plastique
Plateau porte-
disque abrasif de
finition
Pour le ponçage dans les coins et les
autres endroits difficiles d’accès
Feuilles de papier
abrasif
Une (1) feuille de papier abrasif (grain
de 60), trois (3) feuilles de papier abrasif
(grain de 80) et une (1) feuille de papier
abrasif (grain de 120) sont fournies pour
différentes applications de ponçage
Adaptateur
Installer l’adaptateur à l’une des sorties
afin de pouvoir utiliser différentes marques
d’accessoires.
INSTALLATION DE LA TÊTE
Voir la figure 1.
Retirer le bloc-piles de la base pour entraînement ou débrancher la base pour
entraînement de l’alimentation électrique.
Placer la tête sur la base pour entraînement et appuyer jusqu’à ce que les loquets
s’enclenchent en place. Tirer sur la tête pour s’assurer qu’elle est fixée solidement
avant de commencer l’opération.
NOTE : La tête peut être installée à des angles de 90° afin de s’adapter à l’application
visée.
AVERTISSEMENT :
La bride pour accessoire sur cet outil représente un risque possible de
pincement et doit être manipulée avec soin. Garder les doigts éloignés de la
bride pour accessoire lors de la rotation du levier coulissant vers la position
de blocage.
INSTALLATION DES ACCESSOIRES
Voir les figures 2 à 6.
Retirer le bloc-piles de la base pour entraînement ou débrancher la base pour
entraînement de l’alimentation électrique.
A
B
C
A
A
A
A
A
B
B
B
C
C
A
B
C
B
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
RIDGID R28602-AC24J14 User manual
- Category
- Power tools
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: RIDGID R28602-AC24J14 Manuel utilisateur
- español: RIDGID R28602-AC24J14 Manual de usuario
Related papers
-
RIDGID R822350002 User guide
-
-
-
-
-
-
-
-
-
