Uniden DXI5586-4 User manual

[ 2 ] www.uniden.com
Contents
Welcome/Features 3
Controls and Functions 4
Terms Used in this Manual 6
Accessibility 6
Installing the Phone 7
A. Choose the Best Location 7
B. 
Install the Rechargeable Battery Packs into the Handsets
8
C. 
Connect the Main Base and Charging Cradle, and Charge the Handsets
9
D. Mount the Main Base on a Wall 11
Installing the Beltclip 12
Headset Installation 13
Register Handsets to the Main Base before Using!
13
When to Re-register Handsets 14
Basic Setup 15
Activating AutoTalk 15
Activating Caller ID on Call Waiting 15
Entering Your Area Code 16
Choosing the Dialing Mode 16
Setting the Language 17
Selecting the Ring Tone and Volume 17
Using Your Phone 18
Making and Receiving Calls 18
Transferring a Call 19
Redialing the Last Dialed Number 19
Adjusting the Earpiece Volume 20
Tone Dialing Switch-over 20
Traveling Out-of-Range 21
Selecting a Different Channel 21
Find Handset 21
Using Call Waiting 22
Voice Mail Waiting Indicator 22
Using the Speed Dial Memory 23
Storing Names and Numbers in Speed Dial Memory 23
Storing Caller ID Messages in Speed Dial Memory 26
Making Calls from Speed Dial Memory 27
Caller ID and CIDCW (Caller ID on Call Waiting)
28
Viewing the Caller ID Message List 29
Deleting Information from the Caller ID List 30
Making a Call from the Caller ID List 31
Caller ID on Call Waiting (CIDCW) 31
Changing the Digital Security Code 32
Note on Power Sources 33
General Information 35
Troubleshooting 36
Liquid Damage 39
Precautions & Warranty 40
I.C. Notice 42
Index 43
Memory List 46

WELCOME/FEATURES [ 3 ]www.uniden.com

Welcome

Congratulations on your purchase of the Uniden dual handset cordless telephone. This

cordless phone is designed and engineered to exacting standards for reliability, long life,

and outstanding performance.

Note: Illustrations in this manual are used for explanation purposes. Some

illustrations in this manual may differ from the actual unit. The color

of your cordless telephone may vary.

If you have any trouble with your phone, call our Customer Hotline at 1- 800-297-1023,

Mon-Fri 7 am to 7 pm, Sat/Sun 9 am to 5 pm, CST. (Phone support is closed on holidays.)

For more information on Uniden products and accessories, be sure to visit our web site:

www.uniden.com

Uniden

®

is a registered trademark of Uniden America Corporation.

AutoTalk, AutoStandby, UltraClear Plus, Random Code and AutoSecure are trademarks of

Uniden America Corporation.

Features

• 5.8GHz Extended Range Technology

• Dual Handset System

(Extra Handset & Charger Included)

• Call Transfer from Handset to Handset

• Caller ID/Caller ID on Call Waiting

• 3-Line Backlit LCD

• Trilingual Menu Displays

• 30 Caller ID Memory

• 10 Number Memory Dialing

• Last Number Redial

• Voice Mail Waiting Indicator

• Tone/Pulse Dialing

• Page/Find Handset Key

• Earpiece/Ringer Volume Controls

• Mute or Turn Ringer Off

• Hearing Aid Compatible

• 20 Channel Auto Scan

• Desk or Wall Mountable

CONTROLS AND FUNCTIONS[ 4 ] www.uniden.com

2

4

3

5

1

6

8

7

9

20

15

14

13

10

12

11

18

19

16

17

1. Handset antenna

2. Beltclip hole

3. Jack for optional headset

4. Handset ringer speaker

5. Handset battery compartment

6. Handset earpiece

7. LCD display

8.

▼ (volume & scroll down) key

9. Call id (Caller ID)/menu key

10. /tone/ (left cursor) key

11. Redial/pause key

12. Select/channel key

13.

▲ (volume & scroll up) key

14. End key

15. Talk/flash key

16. #/ (right cursor) key

17. Memory key

18. Delete/transfer key

19. Handset microphone

20. Handset charging contacts

Controls and Functions

CONTROLS AND FUNCTIONS [ 5 ]www.uniden.com

25

24

21

22

23

21. Main base charging contacts

22. Find hs key

23. Charge/in use and VMWI

(Voice Mail Waiting Indicator) LED

24. Telephone line jack

25. DC IN 9V jack

26. Charging contacts

27. Charge LED

28. DC IN 9V jack

Extra Charging Cradle (for Second Handset)

26

28

27

Main Base

TERMS USED IN THIS MANUAL / ACCESSIBILITY[ 6 ] www.uniden.com

Accessibility

Uniden provides a customer service hotline for accessibility questions. If you have a disability and need

customer service assistance or if you have any questions about how Uniden's products accommodate

persons with disabilities, please call the accessibility voice/TTY line:

1-800-874-9314

A representative is available to talk to you M-F, 8:00 am to 5:00 pm, CST. After hours, you can leave a

message, and we will call you back. Information is also available on our web site, www.uniden.com,

under the "Accessibility" link.

Terms Used in this Manual

• Standby Mode - The handset may be sitting in or off the cradle, but is NOT in use. The talk/flash key has

not been pressed and there is no dial tone.

• Talk Mode - The handset is off the cradle and the

talk/flash key has been pressed, enabling a dial tone.

• CID - Caller ID

• CIDCW - Caller ID on Call Waiting

INSTALLING THE PHONE [ 7 ]www.uniden.com

INSTALLING THE

PHONE

Installing the Phone

Do the following steps:

A. Choose the Best Location

B. Install the Rechargeable Battery Packs into the Handsets

C. Connect the Main Base and Charging Cradle, and Charge the Handsets

D. Mount the Main Base on a Wall

A. Choose the Best Location

Before choosing a location for your new phone, here are some important guidelines

you should consider:

• The location should be close to both a phone jack and a continuous power outlet

(one which is not connected to a switch).

• The main base and each handset should be kept away from sources of electrical

noise such as motors, microwave ovens, and fluorescent lighting.

• The cradle can be placed on a desk, tabletop, or mounted on a standard wall plate.

For better reception, place the main base as high as possible.

• The main base should be placed in an open area for optimum range and reception.

Avoid excessive moisture,

extremely low temperatures,

dust, mechanical vibration,

or shock

Avoid heat sources, such as radiators,

air ducts, and sunlight

Avoid television sets and other

electronic equipment

Avoid noise sources such as a window

by a street with heavy traffic

Avoid microwave ovens

Avoid personal computers

Avoid other cordless telephones

Choose a central location

If your home has

specially wired alarm

equipment connected to

the telephone line, be

sure that installing the

system does not disable

your alarm equipment.

If you have questions

about what will disable

your alarm equipment,

contact your telephone

company or a qualified

installer.

INSTALLING THE PHONE[ 8 ] www.uniden.com

B. Install the Rechargeable Battery Packs into the

Handsets

Both handsets are powered by rechargeable battery packs.

The battery recharges automatically when the handset is

placed in the main base or charging cradle.

1) Press down on the handset battery case cover (use the

finger indention for a better grip) and slide the cover

downward to remove.

2) Plug the battery pack connector (red & black wires) into

the small jack inside the battery compartment.

(The connector notches fit into the grooves of the jack only

one-way.) Match the wire colors to the polarity label in the

battery compartment, connect the battery, and listen for

a click to insure connection.

3) Make sure you have a good connection by slightly pulling

on the battery wires. If the connection is secure, the

battery jack will remain in place.

4) Place the battery case cover back in the handset by sliding

it upwards until it clicks into place.

Use only the Uniden

(BT-905) rechargeable

battery pack supplied

with your phone.

INSTALLING THE

PHONE

INSTALLING THE PHONE [ 9 ]www.uniden.com

• Connect the AC adapter to a continuous power supply.

• Place each cradle close to the AC outlet to avoid long extension cords.

C. Connect the Main Base and Charging Cradle, and Charge the Handsets

1) Connect each AC adapter to the DC IN 9V

jack and to each standard 120V AC wall

outlet.

2) Place one handset in the main base and

the other in the charging cradle with the

keypad facing forward.

3) Make sure that the

charge/in use LED and

charge LED illuminate. If the LED does not

illuminate, check to see that the AC

adapter is plugged in and that the handset makes good

contact with the cradle's charging contacts.

• Use only the supplied

AD-314 AC adapter

for the main base and

AD-310 or AD-1010

for the charging

cradle.

Do not use any other

AC adapter.

• Do not place the power

cord where it creates a

trip hazard or where it

could become chafed

and create a fire or

electrical hazard.

4) Charge your handsets at least 15-20 hours before

plugging the phone line.

INSTALLING THE PHONE[ 10 ] www.uniden.com

5) Once the handset battery packs are fully

charged, connect the telephone line cord to

the

TEL LINE jack and a telephone outlet.

If your telephone outlet isn't modular,

contact your telephone company for

assistance.

Modular

INSTALLING THE

PHONE

INSTALLING THE PHONE [ 11 ]www.uniden.com

Standard wall plate mounting

This phone can be mounted on any standard wall

plate.

1) Plug the AC adapter to the

DC IN 9V jack.

2) Route the AC adapter cord through the molded

wiring channel as shown.

3) Plug the AC adapter into a standard 120V AC

wall outlet.

4) Plug the telephone line cord into the

TEL

LINE

jack.

5) Plug the telephone line cord into the

telephone outlet.

6) Align the mounting slots on the main base

with the mounting posts on the wall. Then

push in and down until the phone is firmly

seated.

D. Mount the Main Base on a Wall

INSTALLING THE PHONE[ 12 ] www.uniden.com

Direct wall mounting

If you don't have a standard wall plate, you can mount your phone

directly to the wall. Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the

mounting location that could cause a hazard when inserting

screws into the wall.

• Try to mount your phone within 5 feet of a working phone jack

to avoid excessive lengths.

• Make sure the wall material is capable of supporting the weight

of the main base and handset.

• Use #10 screws (minimum length of 1-3/8 inches) with anchoring

devices suitable for the wall material where the main base will

be placed.

1) Insert two mounting screws into the wall (with their appropriate anchoring

device), 3-15/16 inches apart.

Allow about 1/8 of an inch between the wall and screw heads for mounting the

phone.

2) Refer to steps 1 through 6 on page 11 to mount the telephone.

Installing the Beltclip

To attach the beltclip

Insert the beltclip into the holes on each side of the handset. Press down until it clicks.

To remove the beltclip

Pull both sides of the beltclip to release the tabs from the holes.

INSTALLING THE

PHONE

INSTALLING THE PHONE [ 13 ]www.uniden.com

Headset Installation

Your phone may be used with an optional headset. To use this feature,

insert the headset plug into the headset jack.

Your phone is ready for hands-free conversations.

(Headsets may be purchased by visiting our website at www.uniden.com

or by calling our Parts Department. See page 35.)

Register Handsets to the Main Base before Using!

Whichever handset you choose to charge in the main base will automatically register

to the main base.

The second handset (charging in the extra charging cradle) MUST also be registered

to the main base before use. Follow the steps below to register the second handset.

1) Be sure both handsets are fully charged.

2) Remove the handset from the charging cradle, and place it in the main base. The

charge/in use LED light on the main base will begin to flash, indicating that the

registration is taking place.

3) Wait for at least 5 seconds, then remove the handset from the main base.

4) Press the

find hs key on the main base. If both handsets beep, registration is

complete. If one handset does not beep, re-register that handset.

5) Once both handsets are registered, it doesn’t matter which handset is placed in

the main base or the charging cradle.

• When you charge the

handsets, Caller ID

summary screen and

the name of the

handset, HS1 appears.

If HS2 appears, you

are charging the

handset No. 2.

• The charging cradle

can be used to charge

either handset.

WHEN TO RE-REGISTER HANDSETS[ 14 ] www.uniden.com

Make sure to return the

handsets to the cradles

after each phone call.

When to Re-register Handsets

1) You’ll need to re-register the second handset (follow steps on page 13) each time

the digital security code is changed. Refer to page 32 for details regarding the

Digital Security Code.

2) When there is a power failure for more than one hour:

If power failure occurs (e.g. due to electrical storm or if the unit is unplugged

during a move), both handsets will need to be re-registered. To re-register, follow

the same registration process on page 13.

3) If the second handset’s battery becomes very low, the handset must be recharged

for 15-20 hours and re-registered to the main base unit.

BASIC SETUP

BASIC SETUP [ 15 ]www.uniden.com

Basic Setup

There are five basic options that you will need to set up: AutoTalk, CIDCW (Caller ID

on Call Waiting), Area Code, Dial Mode and Language.

CIDCW and Dial Mode options can only be set by using Handset

1. If you try to set by using Handset 2, you will not see these

options listed on the LCD screen. (Headset 1 shows

HS1 in the

display while the phone is charging.) AutoTalk, Area Code and

Language options can be set by using either Handset 1 or Handset 2.

Activating AutoTalk

AutoTalk allows you to answer the phone simply by removing the handset from the

cradle. You do not have to press any keys.

1) When the phone is in standby mode, press and hold the

call id/menu key. The following screen appears.

2) Press the

select/channel key to turn AutoTalk on.

3) Press the

end key to complete the setting. The handset returns to standby mode.

Activating Caller ID on Call Waiting

Caller ID allows you to see the name and number of the calling party before you

answer the phone. Caller ID on Call Waiting (CIDCW) lets you see the name and

number of a call that comes in when you are on the line.

You must subscribe to Caller ID service through your local

telephone provider to use this feature.

1) When the phone is in standby mode, press and hold the

call id/menu key. The following screen appears.

2) Press the

▼ key to select CIDCW.

BASIC SETUP[ 16 ] www.uniden.com

1) When the phone is in standby mode, press and hold the

call id/menu key. The following screen appears.

2) Press the

▼ key twice to select Area Code.

3) Press the

select/channel key. If an area code was already

stored, the phone will display it.

4) Use the number keys (

0 - 9) to enter the 3-digit area code.

If you make an error, use the

delete/transfer key to back-

space.

5) Press the

select/channel key. A confirmation tone sounds.

6) Press the

end key to complete the setting. The handset returns to standby mode.

Choosing the Dialing Mode

Your phone can communicate with the telephone network in two different ways: tone

dialing and pulse dialing. These days, most phone networks use a method called tone

dialing, so your phone comes programmed for tone dialing.

If your phone company uses pulse dialing, you'll need to change your phone's dial

mode. There's an easy way to tell: try making a call. If your call connects, your

phone's setting is fine. If not, follow the steps below:

3) Press the select/channel key to toggle and turn on Caller ID on Call Waiting.

4) Press the

end key and return the handset to the main base to complete the

setting. The handset returns to standby mode.

Entering Your Area Code

If you can make a call by dialing only 7 digits (instead of 10), you can program your

local area code in your phone. If you get a call from within your area code, you'll

only see the 7-digit phone number. If you get a call from outside your area code,

you'll see all 10 digits.

If your phone system

requires pulse dialing

and you need to send

the DTMF tones during a

call, you can temporarily

switch over to tone

dialing. (Refer to "Tone

Dialing Switch-over" on

page 20.)

BASIC SETUP

BASIC SETUP [ 17 ]www.uniden.com

1) When the phone is in standby mode, press and hold the

call id/menu key. The following screen appears.

2) Press the

▼ key three times to select Dial.

3) Press the

select/channel key to set the phone to pulse

dialing.

4) Press the

end key and return the handset to the main base to complete the

setting. The handset returns to standby mode.

Setting the Language

You can change the language the menu display uses. Choose from English, French, or

Spanish.

1) When the phone is in standby mode, Press and hold the

call id/menu key. The following screen appears.

2) Press the

▼ key four times to select Language.

3) Press the

select/channel key to select Eng, Fr. or Esp.

4) Press the

end key to complete the setting.

The handset returns to standby mode.

Selecting the Ring Tone and Volume

Your phone has five different ringer tone/volume combinations you can choose from.

1) With the phone in standby mode, press the

▲ or ▼ key.

2) The phone will sound the different ring tones at different volumes. To turn the

ringer off, select

Ringer Off.

3) When the phone sounds the ring tone and volume you wish to use, press the

end key.

USING YOUR PHONE[ 18 ] www.uniden.com

Using Your Phone

Making and Receiving Calls

Making a call

1) Remove the handset from the cradle.

2) Press the

talk/flash key.

3) Listen for the dial tone.

4) Dial the number.

OR

1) Remove the handset from the cradle.

2) Dial the number.

3) Press the

talk/flash key.

Receiving a call

1) Remove the handset from the cradle. (If AutoTalk is on, the phone will

automatically answer the call when you pick it up.)

2) Press the

talk/flash key.

OR

1) If the handset is off the cradle, press the

talk/flash, /tone/ , #/ or any

number key. (AutoTalk is on.)

Hanging up

Press the end key or return the handset to the cradle.

To turn on the AutoTalk

feature, see "Activating

AutoTalk" on page 15.

USING YOUR PHONE

USING YOUR PHONE [ 19 ]www.uniden.com

Transferring a Call

Your cordless phone allows you to transfer outside calls from handset to handset,

only one handset at a time can talk with an outside caller. The second handset

cannot go off hook to listen to conversations or make an outgoing call while the

other handset is in use.

To transfer a call

1) During a call, press the delete/transfer key. The call will

automatically be placed on hold and the transfer tone sounds.

2) When the other handset receives the call, the transfer tone stops.

To cancel the transfer and return to the caller, press the

delete/transfer or talk/flash

key on the handset.

To receive a transfer call (from the second handset)

Pick up the handset from the cradle (when AutoTalk is set to

on), or pick up the handset and press the

talk/flash key to

answer the transferred call. Additionally, you can answer the transferred call by

pressing any number key, the

/tone/ or #/ key (when AutoTalk is set to on).

Redialing the Last Dialed Number

1) Remove the handset from the cradle.

2) Press the

talk/flash key.

3) Listen for the dial tone.

4) Press the

redial/pause key.

OR

1) Remove the handset from the cradle.

2) Press the

redial/pause key.

3) Press the

talk/flash key.

If you transfer a call

and it is not picked up

after 5 minutes, the call

will be disconnected.

USING YOUR PHONE[ 20 ] www.uniden.com

Adjusting the Earpiece Volume

To change the earpiece volume, press the ▲ or ▼ key during a

call.

Temporarily Mute Ringer

If the handset is off the cradle while an incoming call is

ringing, simply press the

end key to mute the incoming ring.

The ringer will sound with the next incoming call.

You can only mute the

handset ringer if the

handset is off the cradle

when the phone starts

ringing.

Tone Dialing Switch-over

If your telephone company requires pulse dialing, you can

switch over to tone dialing after the call connects.

This feature is useful when you need tone dialing to use

automated such as telephone bank tellers, telephone

prescription refills, customer support menus,etc.

If your phone is set to pulse dialing mode, make your call normally. Once your call

connects, press the

/tone/ key. Any digits you enter from then on will be sent

as tone digits. When this particular call ends, the phone automatically returns to

pulse dialing mode.

Page is loading ...

Uniden DXI5586-4 User manual

This manual is also suitable for

Uniden DXI5586-4 User manual

Related papers

Other documents