Philips 170B2M User manual

Category
TVs & monitors
Type
User manual
Philips 170B2M Electronic User's Manual
file:///D|/Grace/K1/english/170b2m/index.htm [11/22/2001 1:34:34 PM]
Safety and Troubleshooting Information
Safety Precautions and MaintenanceInstallation Locations FAQsTroubleshooting
Regulatory InformationOther Related Information
Safety precautions and maintenance
WARNING: Use of controls, adjustments, or procedures other than those
specified in this documentation may result in exposure to shock, electrical
hazards, and/or mechanical hazards.
Read and follow these instructions when connecting and using your computer monitor:
Unplug the monitor, if you are not going to use it for an extensive period of time.
Unplug the monitor, if you need to clean it with a slightly damp cloth. Wiping the screen with a dry
cloth is possible when the power is off. However, never use alcohol, solvents, or ammonia-based
liquids.
Consult a service technician if the monitor does not operate normally when following the instructions
in this manual.
The casing cover should be opened only by qualified service personnel.
Keep the monitor out of direct sunlight and away from stoves or any other heat source.
Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.
Do not block the ventilation holes on the cabinet.
Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.
When positioning the monitor, make sure the power plug and outlet are easily accessible.
If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds, then attach
the power cable or DC power cord for normal operation.
To avoid the risk of shock or permanent damage to the set, do not expose the monitor to rain or
excessive moisture.
When positioning the monitor, make sure the power plug and outlet are easily accessible.
IMPORTANT: Always activate a screen saver program during your application . If a still image in high
contrast remains on the screen for an extended period of time, it may leave a so called "after-image"
or "ghost image" in front of the screen. This is a well-known phenomenon that is caused by the
shortcomings inherent in the LCD technology. Most of the time the after-image will disappear
gradually over a period of time after switching off the power. Be aware that the after-image symptom
can not be repaired and is not covered under warranty.
Consult a service technician if the monitor does not operate normally when operating instructions of this
manual are followed.
RETURN TO TOP OF THE PAGE
Safety & Troubleshooting
file:///D|/Grace/K1/english/170b2m/safety/safety.htm (1 of 2) [11/22/2001 1:34:36 PM]
Installation Locations
Avoid Heat and Extreme Cold
Do not store or use the LCD monitor in locations exposed to heat, direct sunlight, or extreme cold.
Avoid moving the LCD monitor between locations with large temperature differences. Choose a site
falling within the following temperature and humidity ranges.
Temperature: 5-35°C 41-95°F
Humidity: 20-80% RH
Do not subject the LCD monitor to severe vibration or high impact conditions. Do not place the LCD
monitor inside a car trunk.
Take care not to mishandle this product by either knocking or dropping during operation or
transportation.
Do not store or use the LCD monitor in locations exposed to high humidity or a dusty environment.
Also do not allow water or other liquids to spill on or into the LCD monitor.
RETURN TO TOP OF THE PAGE
Safety & Troubleshooting
file:///D|/Grace/K1/english/170b2m/safety/safety.htm (2 of 2) [11/22/2001 1:34:36 PM]
About This Manual
About This GuideNotational Descriptions
About This Guide
This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD
monitor's features, setup, operation and other pertinent information. Its contents are identical to the
information in our printed version.
Sections are as follows:
Safety and Troubleshooting Information provides tips and solutions for common problems as well as
other related information you may need.
About This Electronic User's Manual gives an overview of information included, along with notation
icon descriptions and other documentation for your reference.
Product Information gives an overview of the monitor's features and as well as the technical
specifications for this monitor.
Installing Your Monitor describes the initial setup process and gives an overview of how to use the
monitor.
On Screen Display provides information on adjusting the settings on your monitor.
Customer Care and Warranty contains a list of worldwide Philips Consumer Information Centers
along with help desk phone numbers and information on the warranty applicable to your product.
Glossary defines technical terms.
Download and Print Option transfers this entire manual to your hard drive for easy reference.
RETURN TO TOP OF THE PAGE
Notational Descriptions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type.
These blocks contain notes, cautions, or warnings. They are used as follows:
NOTE: This icon indicates important information and tips that help you make better
use of your computer system.
About This Electronic User's Manual
file:///D|/Grace/K1/english/170b2m/about/about.htm (1 of 2) [11/22/2001 1:34:38 PM]
CAUTION: This icon indicates information that tells you how to avoid either potential
damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you how to
avoid the problem.
Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the
specific presentation of the warning is mandated by regulatory authority.
RETURN TO TOP OF THE PAGE
©2001 Koninklijke Philips Electronics N.V.
All rights reserved. Reproduction, copying, usage, modifying, hiring, renting, public performance, transmission and/or broadcasting in whole or in
part is prohibited without written consent of Philips Electronics N.V.
About This Electronic User's Manual
file:///D|/Grace/K1/english/170b2m/about/about.htm (2 of 2) [11/22/2001 1:34:38 PM]
Product Information
Product FeaturesTechnical SpecificationsResolution & Preset ModesPhilips Pixel
Defect PolicyAutomatic Power SavingPhysical SpecificationPin Assignment
Product ViewsPhysical Function
Product Features
170B2M
17-inch color LCD monitor with excellent display performance
Triple input featuring two connectors - accepts DVI-I digital/analog and VGA analog inputs
Embedded AC power supply
Front firing speakers with 48W PMPO stereo sound output
Advanced AUTO adjustment optimizes picture quality
Rotation for both portrait and landscape display
Liner height adjustment for best viewing position
Adjustable tilt and swivel function
User installable bezel for optional protective cover choice
Optional self-powered USB hub
RETURN TO TOP OF THE PAGE
Technical Specifications*
LCD PANEL
• Type TFT LCD
• Screen size 17" / 43.2cm diagonal
• Pixel Pitch 0.264 x 0.264mm
• LCD Panel type
1280 x 1024 pixels
R.G.B. vertical stripe
Anti-glare polarizer, hard coated
• Effective viewing area 337.9 x 270.3 mm
• Display Colors 8 bits interface (16M colors)
SCANNING
Vertical refresh rate 56Hz-76Hz
Horizontal Frequency 30KHz-82KHz
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (1 of 9) [11/22/2001 1:34:40 PM]
VIDEO
• Video dot rate 135MHz
• Input impedance
- Video 75 Ohm
- Sync 2K Ohm
• Input signal levels 0.7 Vpp
• Sync input signal
Separate sync
Composite sync
Sync on green
• Sync polarities Positive and negative
• Video interface
Triple input (two connectors): D-Sub (analog) and DVI-I (accepts
both digital and analog) are available and user selectable
AUDIO
• Input signal level 0.7 Vpp
• Headphone out signal level 32 Ohm 20+20mW
• Input signal connector 3.5mm mini jack
• Loudspeaker 2+2W RMS stereo front firing (PMPO: 48W)
MICROPHONE
• Sensitivity -55dB re 1V/ubar at 1KHz
• Output impedance 2.2K Ohm max.
• Directivity -5dB at 180°
• Frequency range 300Hz-3KHz
Optical characteristics
• Contrast ratio: 400 (typ.)
• Brightness:
250 cd/m
2
(typ.)
• Peak contrast angle 6 o'clock
• White Chromatcity:
x: 0.281 y: 0.311 (at 9300°K)
x: 0.312 y: 0.338 (at 6500°K)
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (2 of 9) [11/22/2001 1:34:40 PM]
• Viewing Angle:
(C/R>5)
Upper >80° (typ.)
Lower >80° (typ.)
Left >80 ° (typ.)
Right >80 ° (typ.)
• Response time <40ms (typ.)
* These information are subject to change without notice.
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
• Maximum 1280 x 1024 at 75Hz
• Recommended 1280 x 1024 at 60Hz
32 user definable modes
15 factory preset modes:
H. freq (KHz) Resolution V. freq (Hz)
31.5 640*350 70 (IBM VGA 10h)
31.5 720*400 70
31.5 640*480 60
35.0 640*480 67
37.5 640*480 75
35.2 800*600 56
37.9 800*600 60
46.9 800*600 75
49.7 832*624 75
48.4 1024*768 60
60.0 1024*768 75
69.0 1152*870 75
71.8 1152*900 76 (SUN Mode II)
63.9 1280*1024 60
80 1280*1024 75
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (3 of 9) [11/22/2001 1:34:40 PM]
RETURN TO TOP OF THE PAGE
Automatic Power Saving
If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can
automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or
other input device is detected, the monitor will automatically "wake up". The following table shows the
power consumption and signaling of this automatic power saving features:
Power Management Definition
VESA Mode Video H-sync V-sync Power Used LED color
ON Active Yes Yes < 50W Green
Stand-by Blanked No Yes < 2W Amber
Suspend Blanked Yes No < 2W Amber
OFF Blanked No No < 2W Amber
This monitor is ENERGY STAR
®
compliant. As an ENERGY STAR
®
Partner, PHILIPS has
determined that this product meets the
ENERGY STAR
®
guidelines for energy efficiency.
RETURN TO TOP OF THE PAGE
Physical Specifications
• Dimension (WxHxD) 414 x 428 x 184 mm (incl. Pedestal)
• Weight 7.7 Kg
• Tilt / Swivel 0° ~ 35° / + - 175°
• Height adjustment rang 50mm
• Portrait display 90° rotation counter clockwise
• Power supply 100 — 240 VAC, 50/60 Hz
• Power consumption 40 W (typ.)
• Temperature
5° C to 35° C (operating)
-20° C to 60° C (storage)
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (4 of 9) [11/22/2001 1:34:40 PM]
• Relative humidity 20% to 80%
• System MTBF 50K hrs (including CCFL 50K hrs)
* These information are subject to change without notice.
* Resolution 1280x1024, standard size, contrast max., brightness 50%, 9300° K, full white pattern,
without audio/USB.
RETURN TO TOP OF THE PAGE
Pin Assignment
1. The digital/analog DVI-I onnector contains 29 signal contacts organized in three rows of eight contacts.
Signal pin assignments are listed in the following table:
Pin
No.
Signal
Assignment
Pin
No.
Signal
Assignment
Pin
No.
Signal
Assignment
Pin
No.
Signal
Assignment
1 TMDS Data 2- 9 TMDS Data 1- 17
TMDS Data
0-
C1
Analog Red Video
Out
2 TMDS Data 2+ 10 TMDS Data 1+ 18
TMDS Data
0+
C2
Analog Green
Video Out
3
TMDS Data 2/4
Shield
11
TMDS Data 1/3
Shield
19
TMDS Data
0/5 Shield
C3
Analog Blue Video
Out
4 TMDS Data 4- 12 TMDS Data 3- 20
TMDS Data
5-
C4
Analog Horizontal
Sync
5 TMDS Data 4+ 13 TMDS Data 3+ 21
TMDS Data
5+
C5
Analog Common
Ground Return
(Red, Green, Blue
Video Out)
6 DDC Clock 14 +5V Power 22
TMDS Clock
Shield
7 DDC Data 15
Ground (+5V,
Analog H/V Sync)
23
TMDS
Clock+
8
Analog Vertical
Sync
16 Hot Plug Detect 24 TMDS Clock-
2. The 15-pin D-sub connector (male) of the signal cable:
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (5 of 9) [11/22/2001 1:34:40 PM]
Pin
No.
Assignment
Pin
No.
Assignment
1 Red video input 9 +5V
2 Green video input/SOG 10 Logic ground
3 Blue video input 11
Identical output - connected
to pin 10
4 Sense (GND) 12 Serial data line (SDA)
5 Not connected 13 H. Sync / H+V
6 Red video ground 14 V. Sync (VCLK for DDC)
7 Green video ground 15 Data clock line (SCL)
8 Blue video ground
RETURN TO TOP OF THE PAGE
Product Views
Follow the links to see various views of the monitor and its components.
Front View Product Description
RETURN TO TOP OF THE PAGE
Physical Function
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (6 of 9) [11/22/2001 1:34:40 PM]
1) Tilt
2) Swivel
3) Height adjustment
4) Portrait display
Turn monitor from landscape view to portrait view
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (7 of 9) [11/22/2001 1:34:40 PM]
4.1) Tilt the monitor body at an angle
4.2) Rotate the monitor body 90 degrees counter clockwise.
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (8 of 9) [11/22/2001 1:34:40 PM]
RETURN TO TOP OF THE PAGE
170B2M Product Information
file:///D|/Grace/K1/english/170b2m/product/product.htm (9 of 9) [11/22/2001 1:34:40 PM]
Installing your LCD Monitor
Your LCD Monitor : Front View Product DescriptionConnecting to Your PCRemove and
re-install the baseGetting Started Optimizing PerformanceAccessories (optional)
Front View Product Description
UP and DOWN buttons are used when adjusting the OSD of your monitor
LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used
in adjusting the OSD of your monitor.
BRIGHTNESS hotkey. When the UP and DOWN arrow buttons are
pressed, the adjustment controls for the BRIGHTNESS will show up.
OK button which when pressed will take you to the OSD controls
POWER button switches your monitor on
Automatically adjust the horizontal position, vertical position, phase and
clock setting.
Installing your LCD Monitor
file:///D|/Grace/K1/english/170b2m/install/install.htm (1 of 6) [11/22/2001 1:37:33 PM]
Signal inputs selective hotkeys. Allows user to switch between two video
connectors (D-Sub & DVI-I), e.g. D-Sub <-> DVI-D digital inputs or D-Sub
<-> DVI-A analog inputs.
Audio power on/off and volulme adjustment1.
Audio power LED2.
BASS on/off3.
Built-in Mic4.
Mute on/off5.
RETURN TO TOP OF THE PAGE
Side View
Installing your LCD Monitor
file:///D|/Grace/K1/english/170b2m/install/install.htm (2 of 6) [11/22/2001 1:37:33 PM]
Headphone Jack1.
Microphone Jack2.
RETURN TO TOP OF THE PAGE
Rear View
Installing your LCD Monitor
file:///D|/Grace/K1/english/170b2m/install/install.htm (3 of 6) [11/22/2001 1:37:33 PM]
Audio in1.
Mic out2.
DC 12V in3.
Installing your LCD Monitor
file:///D|/Grace/K1/english/170b2m/install/install.htm (4 of 6) [11/22/2001 1:37:33 PM]
AC power in1.
DC 12V out for Philips Multimedia Base only2.
DVI-I Connector3.
D-SUB Connector4.
RETURN TO TOP OF THE PAGE
Optimizing Performance
For best performance, ensure that your display settings are set at 1024x768@60Hz (for 14"/15") or
1280x1024, 60Hz (for 17"/18").
Note: You can check the current display settings by pressing the "OK" button once.
Go into the Product Information. The current display mode is shown on the item
called RESOLUTION.
You can also install the Flat Panel Adjust (FP Adjust) program, a program for getting the best
performance out of your monitor, included in this CD. A step-by-step instructions is provided to guide
you through the installtion process. Click on the link to know more about this program.
More about
FP_setup01.exe
Installing your LCD Monitor
file:///D|/Grace/K1/english/170b2m/install/install.htm (5 of 6) [11/22/2001 1:37:33 PM]
RETURN TO TOP OF THE PAGE
Installing your LCD Monitor
file:///D|/Grace/K1/english/170b2m/install/install.htm (6 of 6) [11/22/2001 1:37:33 PM]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90

Philips 170B2M User manual

Category
TVs & monitors
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI