2. Axxess
  3. INSTGMOS-LAN-012

Axxess INSTGMOS-LAN-012 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Axxess INSTGMOS-LAN-012 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTGMOS-LAN-012INSTGMOS-LAN-012INSTGMOS-LAN-012
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS
APPLICATIONS
READ IMPORTANT WARNING ON PAGE 1
BEFORE ATTEMPTING ANY INSTALLATION
NOTE: If vehicle does not have factory installed
Steering wheel controls you will not be able to
control factory satellite.
The GMOS-LAN-012 is designed to retain Onstar, OE
satellite, and retain the warning chimes that are nor-
mally lost when the OEM radio is removed. Provides a
12 volt accessory output for aftermarket radio opera-
tion. The GMOS-LAN-012 also provides a mute, park-
ing brake, vss or speed sense, and a reverse output to
make installing an aftermarket navigation radio simple
and less time consuming.
BUICK
Enclave 2007-11
Lucerne 2006-10
CADILLAC
Escalade 2007-11
DTS 2006-2010
SRX 2007-09
CHEVROLET
Avalanche 2007-11
Equinox 2007-09
Express 2008-11
Impala 2006-2010
Monte Carlo 2006-2007
Silverado (new body) 2007-11
Suburban 2007-10
Tahoe 2007-11
Traverse 2009-11
GMC
Acadia 2007-2011
Savanna 2008-11
Sierra 2007-2011
Yukon 2007-11
HUMMER
H2 2008-09
PONTIAC
Torrent 2007-09
Vibe 2009
SATURN
Outlook 2007-09
Vue 2008-09
SUZUKI
XL-7 2007-09
4
5
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certifi ed technicians
Track down – Changes track on radio/satellite station
Volume up - Enter
Chime Volume Adjustment
To adjust the chime volume, use a small screwdriver to
rotate the potentiometer, located on the 16 pin har-
ness side of the interface, clockwise to make the chime
louder and counterclockwise to make the chime softer.
Onstar Level Adjustment
ToadjusttheOnstarvolumelevelfindtheBlack/Yel-
low wire on the 22 pin harness. Push the blue Onstar
button,whilethevoiceisspeakingtaptheBlack/Yellow
wire to ground. There are 4 volume settings for Onstar;
oncethe4thsettingisreachedandtheBlack/Yellow
wire is tapped to ground it will automatically go back to
thefirstvolumesetting.Oncethevolumeissetitwill
stayatthatvolumeuntiltheBlack/Yellowwireistapped
to ground again.
This can be set during installation and then left alone.
If user adjustment is desired, the customer may also
tap volume up or down to adjust the Onstar level.
12 Pin Harness
The 12 pin harness that is attached to the GMOS-
LAN-012 harness is for use with the ASWC (sold
separately). Please refer to the ASWC instructions for
programming and operation.
INSTALLING THE GMOS-LAN-012
1. With all the connections completed, plug the 22
and 16 pin harnesses into the GMOS-LAN-012.
2. Reconnect the negative battery terminal.
3. Plug the 30 pin GM harness into the vehicle side
harness, and plug the aftermarket radio harness
into the aftermarket radio.
4. Cycle the key by turning the ignition on then back
off, then back on again to test the radio.
TESTING THE GMOS-LAN-012
Turn the ignition on, and then turn the aftermarket
radio on.
Push the Onstar button, the radio should turn off and
you should hear Onstar. Push the Onstar cancel button
and the radio should come back on.
INSTGMOS-LAN-012
A. GMOS-LAN-012 Interface
B. GMOS-LAN-012 Harness
A. Cutting Tool
B. Tape
C. Crimping Tool
D. Connectors (I.E. butt-connectors, bell caps, ECT…)
E. Female Spade Connectors (Optional)
*Important:Beforebeginninganyofthefollowing,
disconnect the negative battery terminal to prevent an
accidental short circuit.
INSTALLATION COMPONENTS
REQUIRED TOOLS
INSTALLING THE INTERFACE
• Connect the red wire to the ignition/accessory wire
of the aftermarket radio
• Connect the Orange/White wire to the illumination
wire of the aftermarket radio. If the aftermarket
radio has no illumination wire just tape off the Or-
ange/White wire.
• Connect the blue/white wire to the amp turn on wire
of the aftermarket radio.
• Connect the white wire to the left front positive
1
2
3
A
B
speaker output of the aftermarket radio
• Connect the white/black wire to the left front nega-
tive speaker output of the aftermarket radio
• Connect the gray wire to the right front positive
speaker output of the aftermarket radio
• Connect the gray/black wire to the right front nega-
tive speaker output of the aftermarket radio
• Connect the green wire to the left rear positive
speaker output of the aftermarket radio
• Connect the green/black wire to the left rear nega-
tive speaker output of the aftermarket radio
• Connect the purple wire to the right rear positive
speaker output of the aftermarket radio
• Connect the purple/black wire to the right rear
negative speaker output of the aftermarket radio
• ConnecttheBrownwiretothemutewireofthe
aftermarket radio. If the aftermarket radio does not
haveaMutewire,tapeuptheBrownwire.
Connect the following wires for aftermarket radios
that have navigation built in:
• Connect the Light Green wire to the parking brake
wire of the aftermarket navigation radio.
• ConnecttheBlue/PinkwiretotheVSSorspeed
sense wire of the aftermarket navigation radio.
• Connect the Green/Purple wire to the reverse wire
of the aftermarket navigation radio.
• Connect the Yellow wire to the 12 volt constant/bat-
tery wire of the aftermarket radio
• ConnecttheBlackwiretothegroundwireofthe
aftermarket radio
• ConnecttheBlackwirewiththeringterminaltothe
radio chassis using ISO screws that are supplied
with the radio
TheBlack/Yellowwireandadditional12pinharness
will be discussed later in this manual
• Connect the RCA’s to the AUX input of your after-
market radio (if equipped)
OE Satellite (if equipped)
NOTE: If vehicle does not have factory installed Steer-
ing wheel controls you will not be able to control factory
satellite.
To listen to the factory satellite, change the source of
the radio to AUX.
1. Press and hold the SOURCE button for three
seconds
2. The drivers information center (located in the cen-
ter of your instrument cluster) will now display your
satellite information.
3. To exit Satellite mode press and hold SOURCE for
three seconds.
Listed below are the functions of the Steering wheel
controls
Source – Changes source of the radio/ enters and exits
Satellite mode
Track up - Changes track on radio/satellite station
/