Astonica 50105605 User manual

Brand: Astonica

Model: 50105605

Type: User manual

Astonica 50105605 is a Hi Back Dining Chair that can be assembled easily by following the instructions provided in the manual. It comes with a Limited Warranty of one (1) year from the date of purchase, which covers defects in material and workmanship. The chair is intended for residential, non-commercial use and not intended for heavy use cases. For any problems or questions, users are advised to contact customer service at 1-888-424-3354 instead of returning the product to the retailer.

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER, CONTACT CUSTOMER SERVICE AT

1-888-424-3354

100107rev1

Read the instructions and precautions before use of this product

Please keep this instruction manual for future reference

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER, CONTACT CONSUMER SUPPORT AT

1-888-424-3354

IF YOU ARE A STORE MANAGER OR EMPLOYEE IN NEED OF ASSISTANCE CALL

1-888-851-5569

PLEASE HAVE YOUR STORE NUMBER READY

Limited Warranty

World Factory, Inc. Products for Home Use

World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE

SELLER WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY

FROM REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service

center. Call 1-888-424-3354 for the location of the nearest authorized service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY

INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR

LOSS OF PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

Made in China

Distributed by:

World Factory, Inc.

Coppell, TX 75019

Model No: 50105605

Samoa Cushion Cast Curl Design

Hi Back Dining Chair

Instruction Manual

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

ASSEMBLY INSTRUCTIONS

Carefully remove the contents from the package. If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed.

Figure 1

Figure 2

IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,

DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT

1-888-424-3354.

PARTS & HARDWARE LIST

PART # DESCRIPTION QUANTITY

A Chair Back 1

B Seat 1

C Left Leg/Arm  1

D Right Leg/Arm  1

E M8 Studs 4

F M8 Bolts 4

G Flat Washer 8

H Lock Washers 8

I Hex Nuts 4

Parts Detail

NOTE: This product is intended for residential, non-commercial use.

Install Studs to Left and Right Leg/Arms

(See Figure 1)

1.Install 2 threaded M8 Studs (E) into Left

 Leg/Arm (C) with slotted end of stud

 pointing outwards.

2.Repeat Step 1 with the Right Leg/Arm (D).

Attach Seat to Right and Left Leg/Arm

of Chair

(See Figure 2)

1.Slide the Seat (B) onto studs in the Right

 Leg/Arm through the bolt holes in mounting

 tabs located on the side of the Seat (B).

 Secure the Seat to the studs using Flat

 Washer (G) first, then Lock washer (H) and

 Hex Nut (I). Finger tighten the Hex Nuts (I).

 Do not over tighten.

2.Repeat Step 1 with the Left Leg/Arm (C).

Attach Back to Seat and Leg/Arm Assembly

(See Figure 3)

1.Position the Chair Back (A) between the

 Left (C) and Right (D) Leg/Arms at the rear

 of the seat. Place Lock Washers (H) onto

 the M8 Bolts (F) first, and then place Flat

 Washers (G) onto the M8 Bolts. Thread the

 M8 Bolts through the 4 holes located inside

 of the Chair Back near the bottom and into

 the 4 holes inside the Leg/Arm assembly.

 Tighten the M8 Bolts until the bolt is seated

 securely in the Leg/Arms with an open end

 wrench. Do not force the bolts to turn . This

 will strip the threads.



2.Tighten the Hex Nuts (I) on the studs under

 the seat.

Figure 3

Astonica 50105605 User manual

Astonica 50105605 User manual

Astonica 50105605 User manual

Related papers

Other documents