GB
Brief instructions for washing machines with LCD display
Your washing machine is ready to use
5019 301 05598
Whirlpool is a registered trademark of Whirlpool USA
First use
Please always follow the installation instructions enclosed with the
appliance.
Turn the programme selector knob with the marking to
highlight
“Settings”
.
Select the language and time by pressing
“Up/Down”
.
Confirm your selection by pressing
“OK”
; press
“Up/Down”
to
change the language or time; confirm the language and time with
“OK”
.
If you have accidentally made an incorrect
choice of language...
...you can reset as follows:
- turn the programme selector knob to
“Settings”
;
- press the
“Reset”
button;
- turn the selector switch marking to the top and then back to
Settings.
The desired language can now be selected.
UPDPOGJSN
4FUDMPDL
4FUDPOUSBTU
4FUMBOHVBHF
Up
Down
Please follow
the instructions
on the LCD display
Set language
Set time
In the same way, you can adjust contrast and brightness as well as
switching the buzzer and child safety on and off.
Important Note
Please refer to the installation instructions enclosed in the
appliance.
*UBMJBOP
%FVUTDI
UPDPOGJSN
&OHMJTI
-BOHVBHFDPOGJSNFE
UPDPOGJSN
4FUMBOHVBHF
4FUDPOUSBTU
4FUDMPDL
5PTFUUJNF
5PDPOGJSN
"55&/5*0/
EJEZPVSFNPWF
USBOTQPSUCSBDFT
5PDPOGJSN
Set Child safety
Turn the programme selector knob to
“Settings”
.
Select
“Set Child safety”
and confirm with
“OK”
.
With the child safety activated, you can select a wash programme
and run it, but you cannot change or cancel it while it is running.
If you want to cancel or change a running programme, you can
temporarily release the child safety by pressing simultaneously.
You can then select or run a new programme. While this
programme is running, the child safety device is re-activated in
order to prevent accidental programme changes.
For fault messages, please read through the enclosed “Instructions
for Use” (“Troubleshooting Guide”).
To deactivate Child safety:
- turn the programme selector knob to
“Settings”
;
-select
“Set Child safety”
by pressing
“Up/Down”
, confirm
selection by pressing
“OK”
;
-on the LCD display
“Off”
is flashing - confirm deactivation of
child safety by pressing
“OK”
.
,
5PDPOGJSN
4FU#SJHIUOFTT
4FU#V[[FS
4FU$IJMETBGFUZ
and
3gb05598.fm Page 1 Friday, April 30, 2004 6:19 PM
Black process 45.0° 100.0 LPI
GB
5019 301 05598
Whirlpool is a registered trademark of Whirlpool USA
Select and start
wash programme
Turn the programme selector knob with the marking to highlight
the desired programme.
It will appear on LCD display with the preset speed and
temperature. You can now start the wash programme, or change
the temperature and spin speed and, if required, select additional
options.
Press the “Menu” button to select additional functions (please follow
the instructions on the LCD display). The additional options you can
choose are displayed as symbols on the LCD display:
As soon as you have selected the desired additional options, you
can start the wash programme, by pressing the flashing Start
symbol on the programme selector knob. For that, you must not
go to the end of the selection displayed on the LCD display.
End of cycle
&BTZDBSF
1VTI PS
xD
Pre-
Intensive
Rinse
Rinse hold
Extra care
Easy
Iron
Wash
&/%0'$:$-&
xD
Button functions
Press the
“Menu”
button to call up the next screen.
Activate or deactivate additional options and set the spin speed
and/or temperature with the
“Up/Down”
arrow buttons.
Confirm with
“OK”
.
Press the
“Back”
button
to return to the previous screen.
Press the
“Info”
button to obtain additional information
.
Press the
“Reset”
button:
- to cancel a running wash program;
- to cancel changes to a selected programme (e.g. change of
temperature, selected options) before the programme has been
started;
- to cancel a wash programme stored under
“Memory”
.
Storing frequently used wash
programmes
Turn the programme selector knob to
“Memory”
.
With the arrow buttons, select a free storage space (from M1 to
M10) and confirm with “OK”.
Select the required programme from the list of wash programmes
displayed and confirm with
“OK”
. As already described, you can
change the wash temperature and spin speed and select additional
options as desired.
Confirm with
“OK”
at the end of the displayed selection.
The wash programme will then be stored in the selected storage
space and can be selected again at any time.
Cancelling stored wash programmes
- Turn the programme selector knob to
“Memory”
;
- With the arrow buttons, select the stored wash programme to
be cancelled;
-Press the
“Reset”
button and hold the button down for a few
seconds, until
“Empty”
appears next to the storage space in
question.
,
5PTFMFDU
.FNQUZ
.FNQUZ
.FNQUZ
,
5PTFMFDU
&BTZDBSF
%BJMZMPBE
$PUUPO
,
5PTFMFDU
.FNQUZ
.FNQUZ
.&BTZDBSF x$
3gb05598.fm Page 2 Friday, April 30, 2004 6:19 PM
Black process 45.0° 100.0 LPI
/