Front Runner KRDS001T Installation guide

Brand: Front Runner

Model: KRDS001T

Type: Installation guide

This manual is also suitable for

ENG

Flat Feet (pair) _ 65mm

FASS016

front runner

Thank you for purchasing a pair of Front Runner 65mm Flat Feet.

Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.

Refer to Page 2 for a list of all the components, quantities and tools required.

READ ME !

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD

RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT

RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND

DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO

INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY

FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

IN THE BOX

FIGURE 1.1

1 2 X Foot

2 2 X Stud Plate

3 8 X M8 Nut Cap

4 8 X M8 Nyloc Nut

5 8 X M8 x 16 x 1.6SS Flat Washer

6 4 X M8 x 20 Hex Bolt

IN THE BOX TOOLS NEEDED

IN THE BOX

13MM

1GET ORGANIZED

FIT AND SECURE

2.2

2.3

2.4

2.1

2.2

2.3

Before ﬁtting the Feet to the rack,

remove the Stud Plates (Item 2).

Refer to Figure 1.1.

Loosely ﬁt the Feet to the rack using

M8 x 16 x 1.6SS Flat Washers and M8

Nyloc Nuts (Items 4 & 5) as shown.

The fasteners will be fully tightened

after the rack has been ﬁtted to the

vehicle.

Make sure that the wind deﬂector is

installed before you proceed to the next

step.

See the Rack Fitment Guide (RRSTUNI)

for instructions.

Place your Front Runner Roof Rack onto

your vehicle and ﬁnd the best position for it.

NOTE: The rack should sit level to the

ground, not the vehicle's roof line. Or

slanting slightly down toward the front.

With the rack in place, ﬁnd the best position

for the Feet. It is advised to always use the

ﬁrst and last slat to install feet. Should your

rack be longer, and kit be supplied with

more feet, these feet should be positioned

with no more that three open slats

between them.

Flip the rack so that the bottom of the

rack faces up. Insert two M8 x 20 Hex Bolts

(Item 4) into the machined slots on the slats

that you have identiﬁed.

FIT AND SECURE

2.2

2.4

2.1

2.4

2.5

With the help of a friend, ﬂip the rack right

side up.

Lower the rack onto the tracks while

aligning the Feet with the Stud Plates in the

tracks.

Loosely secure the Feet to the track using

M8 x 16 x 1.6SS Flat Washers and M8 Nyloc

Nuts (Items 4 & 5).

13MM

Before placing the rack onto the vehicle,

slide the Stud Plates (Item 2) removed in

Step 2.3 into the tracks.

Track

Before tightening the Feet to the tracks,

move the rack so the it sits level to the

ground, not the vehicle's roof line, or slanting

slightly down toward the front.

After you have tightened the Feet to the

tracks, center the rack left to right and

fully tighten the fasteners from Step 2.3.

Place M8 Nut Caps on all the Nyloc Nuts.

COMPLETION

3.1

Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner Dealer in person or online.

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam

Share your adventures on:

IMPORTANT!

Front Runner rack kits often have a higher load rating than the vehicles they are mounted to. Please refer to your speciﬁc

vehicle manufacturer for a recommended roof load rating. Front Runner cannot be responsible for improper loading

beyond the vehicle manufacturer's stated load capacity.

Front Runner KRDS001T Installation guide

Brand: Front Runner

Model: KRDS001T

Type: Installation guide

This manual is also suitable for

Download PDF

report

Front Runner KRDS001T Installation guide

This manual is also suitable for

Front Runner KRDS001T Installation guide

Related papers

Other documents