2. Wallenstein
  3. T200 Ball Hitch

Wallenstein T200 Ball Hitch Installation guide

  • Hello! I've reviewed the Installation Instructions for the WALLENSTEIN T200 Ball Hitch. This document provides step-by-step guidance on installing the hitch on compatible firewood conveyors, with details on required tools, parts, and torque specifications. I'm ready to answer any specific questions you have about the installation process.
  • What tools are required for the installation?
    What is the correct torque for the bolts?
    What conveyors does this ball hitch fit?
Rev Mar-2019
INSTALLATION INSTRUCTIONS
Ball Hitch
T
200
Part No. 2280T267
T200
Ball Hitch
2
Safety
Safety
1. Safety Alert Symbol
This Safety Alert Symbol means:
ATTENTION! BE ALERT!
YOUR SAFETY IS INVOLVED!
The Safety Alert Symbol identies important safety
messages on the machine. This symbol means be alert
to the possibility of personal injury or death. Follow
instructions provided.
2. Equipment Operation
WARNING!
Avoid the risk of personal injury or machine
damage! Read the operator’s manual before
using this equipment. Carefully read all safety
messages in the manual and follow all safety
signs on the machine.
T200
Ball Hitch T200 Ball Hitch
3
T200 Ball Hitch
Fits on CT16, CT16B, CT24 and CT24B rewood conveyors.
3 1
2
4
2x
2x
2x
Item
Part No.
Description
Qty
1
Z71530
Hex Bolt, 1/2NC x 3"
2
2
Z72251
Hex Lock Nut, 1/2NC
2
3
Z91614
Hitch Coupler, 2" Ball x 2" x 3500lbs
1
4
Z92303
Safety Chain, 1/4" x 2 ft with Snap
2
Fig. 1 – Parts Breakdown
T200
Ball Hitch
4
Tools Required
Tools Required
• 3/4" spanner and socket wrenches
• Torque wrench
Procedure
1. Empty the conveyor and turn the drive system off.
2. Lower the conveyor fully until it is resting on the
stops.
3. Make sure the hitch is locked, with the pin fully
inserted.
00459
Fig. 2 – Hitch Lock Pin
4. Place the hitch coupler over the conveyor tongue,
then insert the bolts.
5. Place the front bolt through the ends of the safety
chains. Torque to 80 lbf•ft (110 N•m).
80 lbf•ft (110 N•m)
T200
Ball Hitch Tools Required
5
Checking Bolt Torque
The table shown gives correct torque values for
various bolts and capscrews. Tighten all bolts to
the torque values specied in the table, unless
indicated otherwise. Check tightness of bolts
periodically.
IMPORTANT! If replacing hardware, use
fasteners of the same grade.
IMPORTANT! Torqueguresindicatedinthe
table are for non-greased or non-oiled threads.
Do not grease or oil threads unless indicated
otherwise. When using a thread locker,
increase torque values by 5%.
NOTE: Bolt grades are identied by their
head markings.
ImperialBoltTorqueSpecications
Bolt
Diameter
Torque Value
SAE Gr. 2 SAE Gr. 5 SAE Gr. 8
lbf•ft N•m lbf•ft N•m lbf•ft N•m
1/4" 68912 12 17
5/16" 10 13 19 25 27 36
3/8" 20 27 33 45 45 63
7/16" 30 41 53 72 75 100
1/2" 45 61 80 110 115 155
9/16" 60 95 115 155 165 220
5/8" 95 128 160 215 220 305
3/4" 165 225 290 390 400 540
7/8" 170 230 420 570 650 880
1" 225 345 630 850 970 1320
/