ML Accessories 12DC25D User manual

ML Accessories
Brand
ML Accessories
Model
12DC25D
Type
User manual

This manual is also suitable for

ML Accessories 12DC25D is a dimmable LED driver designed for indoor use. It offers a compact and efficient solution for powering LED lighting fixtures. With a wide input voltage range of 12-24V DC, it can adapt to various power sources. The driver provides a constant current output, ensuring stable operation for connected LED loads. Its IP20 rating makes it suitable for dry indoor environments. Installation involves connecting the driver to the mains supply and then connecting suitable LED loads to its secondary side.

ML Accessories 12DC25D is a dimmable LED driver designed for indoor use. It offers a compact and efficient solution for powering LED lighting fixtures. With a wide input voltage range of 12-24V DC, it can adapt to various power sources. The driver provides a constant current output, ensuring stable operation for connected LED loads. Its IP20 rating makes it suitable for dry indoor environments. Installation involves connecting the driver to the mains supply and then connecting suitable LED loads to its secondary side.

INSTALLATION & MAINTENANCE MANUAL
12DC25D / 24DC25D
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
12DC25D / 24DC25D
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this product is fitted) does not exceed the rating of the
circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• Do not overload this accessory or subject it to conditions outside its rating
• This product is for indoor use only
• This product is Class II double insulated
• This product is IP20 rated
SAFETY
INSTALLATION
• Provide power to the required point of installation
• Connect the LED driver to the mains supply ensuring the correct polarity is observed (see Fig 1).
Live (brown), Neutral (blue)
GENERAL
WARNING
This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
The maximum constant ambient temperature at the point of installation should not exceed 50 degrees
centigrade.
This product is dimmable with trailing edge dimmers, please check compatibility before installation.
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
• Connect a suitable LED load to the secondary side of the driver + (red) – (black)
• Ensure cable strain relief is securing the cables effectively
• Switch on power supply and check for correct operation
Dimmable LED Drivers
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
12DC25D / 24DC25D
SAFETY
• Installation of this driver should only be carried out by a qualified electrician or competent person to the
latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this driver and LED load is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation
• This unit is rated at IP20
• This product is Class II and does not require an earth
• This product should be placed in a suitable enclosure
• This product is dimmable with most trailing edge dimmers (check compatibility with dimmer manufacturer)
INSTALLATION
• Provide power to the required point of installation
• Connect the LED driver to the mains supply ensuring the correct polarity is observed (see Fig 1). Live (brown),
Neutral (blue)
Fig 1
• Connect a suitable LED load to the secondary side of the driver + (red) – (black)
• Ensure cable strain relief is securing the cables effectively
• Switch on power supply and check for correct operation
WARNING
This product must be disconnected from the circuit if it subjected to any high voltage or insulation resistance testing.
Irreparable damage will occur if this instruction is not followed.
+
-
N
L
Primary
Secondary
Fig 1
AVSEP21_v2
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
59
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the
warranty. If this product should fail within its warranty, period it should be returned to the place of purchase for
a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated
with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter
product specification without prior notice.
-20~
50°C
TA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ML Accessories 12DC25D User manual

ML Accessories
Brand
ML Accessories
Model
12DC25D
Type
User manual
This manual is also suitable for

ML Accessories 12DC25D is a dimmable LED driver designed for indoor use. It offers a compact and efficient solution for powering LED lighting fixtures. With a wide input voltage range of 12-24V DC, it can adapt to various power sources. The driver provides a constant current output, ensuring stable operation for connected LED loads. Its IP20 rating makes it suitable for dry indoor environments. Installation involves connecting the driver to the mains supply and then connecting suitable LED loads to its secondary side.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents