TALOS ITR-CS15D User manual

User’s Manual

ITR-CS15D

Copyrights i

Copyrights

in this document is subject to change without prior

notice in order to improve reliability, design and

function and does not represent a commitment on the

part of the manufacturer.

This document contains proprietary information

protected by copyright. All rights are reserved.

No part of this manual may be reproduced by any

mechanical, electronic, or other means in any

form without prior written permission of the

manufacturer.

All trademarks are property of their respective

owners

Liability Disclaimer

In no event will the manufacturer be liable for

direct, indirect, special, incidental, or

consequential damages arising out of the use or

inability to use the product or documentation,

even if advised of the possibility of such damages.

Regulatory Information

FCC Notices

Safety Statement for

Lithium Battery

CAUTION

RISK OF EXPLOSION IF BATTERY IS

REPLACED BY AN INCOORECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS

TALOS INTEGRATED TECHNOLOGIES

411 BRADWICK DR. UNIT# 11

VAUGHAN, ONTARIO L4K 2P4

ITR-CS15D

Contents

ii

Contents

Copyrights .................................................................................................i

Liability Disclaimer ...................................................................................i

Regulatory Information.............................................................................i

FCC Notices.......................................................................................................... i

Safety Statement for Lithium Battery......................................................i

Contents....................................................................................................ii

1. Hardware Setup....................................................................................4

1.1. Packing Contents......................................................................................... 4

1.2. Quick Tour .................................................................................................... 5

Front View and Side View .............................................................................. 5

Back Panel I/O ............................................................................................... 6

1.3. HDD Replacement ........................................................................................ 6

1.4. Basic Peripherals Installation ..................................................................... 8

Power Adapter ............................................................................................... 8

USB Mouse, USB Keyboard and USB ODD.................................................. 9

LAN Cable...................................................................................................... 9

Cash Drawer .................................................................................................. 9

Customer Display......................................................................................... 10

MSR............................................................................................................. 14

1.5. Adjust Angle ............................................................................................... 15

1.6. Turn on the device...................................................................................... 15

2. Basic Driver Installation ....................................................................16

2.1. Before the installation................................................................................ 16

2.2. Chipset Software Installation .................................................................... 16

2.3. VGA Driver Installation .............................................................................. 17

2.4. Touch Screen Driver and Software Utility installation ............................ 18

2.5. LAN Driver Installation............................................................................... 20

3. Touchscreen Control Panel Quick Guide ........................................23

3.1. Launch TouchKit Utility ............................................................................. 23

3.2. General........................................................................................................ 24

3.3. Settings....................................................................................................... 25

3.4. Tools............................................................................................................ 28

3.5. Display ........................................................................................................ 30

3.6. Edge Compensation .................................................................................. 32

4. I/O Definition.......................................................................................35

4.1. Power Connector ....................................................................................... 35

ITR-CS15D

Contents iii

4.2. Serial Port COM1/3..................................................................................... 35

4.3. COM 2 (10-Pin RJ50) .................................................................................. 35

4.4. Cash Drawer ............................................................................................... 36

5 Specification........................................................................................37

ITR-CS15D

Chapter 1

4

1.

1. Hardware Setup

1.1. Packing Contents

1. ITR-CS15D X 1 4. RJ50 to DB9 COM port adapter cable X 1

2. Power Adapter X 1 5. IO/Cable Cover X 1

3. Power Cord X 1 6. Drive and Utility DVD X 1

ITR-CS15D

Chapter 1 5

1.2. Quick Tour

Front View and Side View

A. The LED indicator will glow green when power is on.

The LED indicator will blink red when the HDD is accessed.

A. Customer Display mounting

hole cover D. Power switch

B. HDD tray E. I/O cover

C. MSR cover

ITR-CS15D

Chapter 1

6

Back Panel I/O

A. DC in G. CD/DIO (for cash drawer)

B. COM 2 (10-pin RJ -50)* H. CF card slot

C. USB 1/2 I. USB 3/4

D. LAN 1 J. COM3

E. LAN 2 K. VGA

F. COM1

CAUTION

* Note: Please use 10-pin RJ50 connector, 8-pin RJ45 is incompatible.

1.3. HDD Replacement

1. Loosen and remove the screws fixing the HDD tray.

2. Pull out the HDD tray slightly and softly.

ITR-CS15D

Chapter 1 7

3. Disconnect the SATA cable connector and the SATA power cable connector.

4. Loosen and remove the four screws fixing the HDD, and then remove the HDD

from the HDD tray.

5. Install the new HDD onto the device in reverse order.

ITR-CS15D

Chapter 1

8

1.4. Basic Peripherals Installation

1. Remove the IO panel cover from the device.

2. All cables and wires from peripherals to the POS device are recommended to

be fed through the base in the direction as shown below.

WARNING

Before the cable cover is removed, please make sure the power is off.

Power Adapter

Connect the DC cable to the DC in jack.

ITR-CS15D

Chapter 1 9

USB Mouse, USB Keyboard and USB ODD

Connect your USB Mouse, USB Keyboard USB ODD or other USB devices to

USB 1/2 or UBS 3/4 ports on the back panel of the device.

LAN Cable

Connect one end of RJ-45 LAN cable to the LAN 1 or LAN 2 port on the back

panel of the device, another end to your internet device.

Cash Drawer

Connect one end of RJ-11 cable to the Cash Drawer port on the back panel of the

device, another end to your cash drawer.

ITR-CS15D

Chapter 1

10

3. Install the IO panel cove.

Customer Display

A. Hardware Installation

1. Remove the two screws and the VFD mounting hole cover from the device,

and then pull out the connector from the device.

2. Adjust the hinge of the VFD, and then connect to the device as shown below.

ITR-CS15D

Chapter 1 11

3. Mount the VFD to the device and tighten the

two M3 screws as shown below.

5. Finished.

B. Power Supply Configuration

1. Power up the ITR-CS15D and hit the DEL key to enter the BIOS. When

the BIOS screen appears use the or key on your external computer keyboard

to select Advanced. Use the arrow keys of the external keyboard to select IO

Configuration, and then press the ENTER key.

WARNING

Never enable the 12V power without the customer display attached and

be sure to disable the 12V power before removing the customer display.

ITR-CS15D

Chapter 1

12

2. The screen below will appear. Use the or key to scroll the screen and

highlight the COM6 RI/12V/15V, and then press the Enter key.

3. Highlight 12V, and then press the Enter key.

ITR-CS15D

Chapter 1 13

4. Press the ESC key to return to the BIOS SETUP UTILITY screen of step 1, use the

or key on your external computer keyboard to select the EXIT.

Use the or key to highlight Save Changes and Exit.

5. Press the Enter key, use the or key to highlight the [Ok], press the Enter

key again to save your voltage configuration and exit BIOS.

ITR-CS15D

Chapter 1

14

MSR

1. Remove the two screws fixing the MSR cover.

2. Remove the MSR cover from the device.

3. Connect the connectors of the MSR assembly to the device.

ITR-CS15D

Chapter 1 15

4. Tighten the two M3 screws to fix the MSR

assembly as shown below.

5. Finished.

1.5. Adjust Angle

1.6. Turn on the device

1. Make sure all peripherals and cables are connected properly.

2. Press and hold the power switch until the power indicator on the front panel

glows green.

ITR-CS15D

Chapter 2

16

2.

2. Basic Driver Installation

2.1. Before the installation

1. Connect an external USB CDROM to the USB power and insert the driver

CD and turn on the device. The program autoruns and displays the Talos

Integrated Technologies main screen.

2.2. Chipset Software Installation

1. On the main screen, click INTEL Chipset Driver.

2. Click Next.

3. Read the License Agreement carefully and cli

c

Yes.

ITR-CS15D

Chapter 2 17

4. Click Next.

5. Click Finish.

2.3. VGA Driver Installation

1. On the main screen, click VGA Driver.

2. Click the operation system according to your

application.

3. Click Next.

4. Read the License Agreement carefully and click Yes.

ITR-CS15D

Chapter 2

18

5. Click Next.

6. Click Next.

7. Select restart your computer right now or later, and then lick Finish.

2.4. Touch Screen Driver and Software Utility installation

1. On the main screen, click Touch Panel

Driver.

2. Click the operation system according to your

application.

ITR-CS15D

Chapter 2 19

3. The procedure starts.

4. Click Next.

5. Check the Install PS/2 interface driver box

and click Next.

6. Select an item according to your needs, and

then click Next.

7. Click OK.

8. If you want to use Multi-Monitor, check the

box and click Next.

9. Click Next.

Page is loading ...

TALOS ITR-CS15D User manual

TALOS ITR-CS15D User manual

Other documents