Hanna Instruments HI 4013 Owner's manual

Brand: Hanna Instruments

Model: HI 4013

Category: Faucets

Type: Owner's manual

This manual is also suitable for

Instruction Manual

SENSOR HANDLE

4000-50

HI 4113

NITRATE

COMBINATION

HI 4013HI 4013

HI 4013

HI 4113HI 4113

HI 4113

Nitrate Ion

Selective Electrode

Half-cell

Combination

HI 4013 Nitrate Half-cellHI 4013 Nitrate Half-cell

HI 4013 Nitrate Half-cell

HI 4113 Nitrate Combination ElectrodeHI 4113 Nitrate Combination Electrode

HI 4113 Nitrate Combination Electrode

I. I.

Introduction:Introduction:

Introduction:

The Hanna HI 4013 and HI 4113 are ion selective elec-

trodes designed for the measurement of nitrate ions in

aqueous solutions. They utilize a replaceable sensing mod-

ule that contains an organic polymer membrane that is

sensitive to nitrate ions. The HI 4013 is a half-cell electrode

that requires a separate reference. The HI 4113 is a combi-

nation ion selective electrode.

IIII

II.

SpecificationsSpecifications

Specifications

Type: PVC membrane with or-

ganic ion exchanger

Ion measured: Nitrate (NO

)

Measurement range: 0.1 M to 1X 10

-5

6200 to 0.62 ppm

Interference:

Organic solvents and cationic detergents must be absent.

Ratio of interfering ion to NO

must be less than the ratio

indicated below:

300 for F

fluoride

100 for Cl

chloride

4 for CO

carbonate

2 for NO

nitrite

0.01 for I

iodide

0.0045 for ClO

perchlorate

Operating Temperature: 0-40°C

Operating pH: 3 to 8 pH (see Section

XIII)

Dimensions: 12 mm (OD) X 120 mm

nominal insertion

(0.47” X 4.72”)

Connection: BNC

III. III.

III.

Theory of OperationTheory of Operation

Theory of Operation

The HI 4013 and HI 4113 nitrate electrodes are potentio-

metric devices used for the rapid determination of free ni-

trate ions in water, emulsified foods and plant samples.

The electrode functions as a sensor or ionic conductor. The

HI 4013 requires a separate reference electrode to complete

its electrolytic circuit. The HI 4113 is a combination elec-

trode with a Ag/AgCl reference electrode with gel stabilized

electrolyte in it’s inner chamber. The external reference

chamber is refillable. The PVC membrane used on the

sensor is impregnated with the organic ion exchanger. This

organic ion exchanger is considered a carrier ionophore in

that it is capable of shielding and carrying the charged

nitrate ion in it’s polar cage freely through the apolar

regions of the membrane. A charge imbalance developes

between the test solution and internal cell of the sensor.

This voltage changes in response to the sample’s ion activ-

ity. When the ionic strength of the sample is fixed, the

voltage is proportional to the concentration of nitrate ions in

solution. The sensor follows the Nernst Equation:

E = E

+ 2.3 RT/nF log A

ion

E = observed potential

= Reference and fixed internal voltages

R = gas constant (8.314 J/K Mol)

n = Charge on ion (-1)

ion

= ion activity in sample

T = absolute temperature in K

F = Faraday constant (9.648 x 10

C/equivalent)

IV. IV.

IV.

Design elements of the HI 4013 and HI 4113Design elements of the HI 4013 and HI 4113

Design elements of the HI 4013 and HI 4113

electrodeselectrodes

electrodes

Upper Cap

Spring

O-Ring

Ceramic Junction

on Inner Stem

Fill Hole

O-Ring and

Plug

Sensing Module

Outer Sleeve

Upper

Threads

Liquid junction

SENSO

HANDLE

4000-50

Cap

Sensing

module

Sensor

Handle

O-Ring

V. V.

Equipment required:Equipment required:

Equipment required:

• The HI 4013 requires the Hanna HI 5315 Double

junction reference electrode with HI 7078 as external

electrolyte.

• Hanna HI 4222 pH/ISE/mV meter or other suitable

ion or pH/mV meter (Note: log/linear graph paper is

useful if an ISE (ion) meter is not available).

• Hanna HI 180 magnetic stirrer or equivalent with

magnetic stirring bars (Note: Isolate beakers from stir-

rer motor heat by placing insulating material such as

foam or cork between them).

• Hanna HI 76404 electrode holder or equivalent.

• Plastic beakers (HI 740036P) or other suitable mea-

surement vessel.

VI. VI.

VI.

Solutions RequiredSolutions Required

Solutions Required

Standards for Nitrate Measurements

0.1 M sodium nitrate standard, 500 mL HI 4013-01

100 ppm nitrate standard, 500 mL HI 4013-02

1000 ppm nitrate standard, 500 mL HI 4013-03

Ionic Strength Adjuster

ISA, 500 mL HI 4013-00

ISISA, 500 mL HI 4013-06

Using volumetric pipettes and glassware make dilutions to

bracket the concentration of the samples. Store samples in

plastic bottles. Standards with concentrations < 10

-3

should be prepared daily.

Two mL of Hanna ISA HI 4013-00 should be added to 100

mL sample or standard.

HI 4013-06 ISISA is Interferent suppressent ISA. Prepare

by dissolving 17.32g Al

(S0

)

0, 3.43.g Ag

, 1.28g

, 2.52g H

NSO

H in approximately 800 mL deion-

ized water. Adjust pH to 3 with 0.1 N NaOH. Dilute to 1

liter. Store in a dark colored container.

For drinking water: 10 mL of ISISA should be added to each

50 mL sample or standard.

VIIVII

VII.

General GuidelinesGeneral Guidelines

General Guidelines

• Ensure the o-ring is installed on modules before screw-

ing into the sensor handle or inner stem.

• Due to shipping or storage the internal solution inside

the PVC modules may have developed an air pocket

near the membrane. Gently shaking the sensor down

(like the old style mercury thermometer) will place the

internal solution next to the membrane.

• Presoaking the Nitrate sensor in a 10

-2

M standard

without ISA for at least half-hour before calibration

will help to optimize the sensor response.

• Do not leave your sensors in standard or samples

with ISA or ISISA for long periods of time.

• Calibration standards and sample solutions should

have the same ionic strength. ISA should be added to

both samples and standards.

• Calibration standards and sample solutions should

be at same temperature.

• Thermally insulate solution vessel from magnetic stir-

rer.

• Calibration standards and sample solutions should

be stirred at the same rate using identical sized TFE

coated stir bars.

• Rinse electrodes with distilled or deionized water be-

tween samples and gently dab dry with lab wipe or

other soft disposable absorbent toweling. Do not rub

the sensing surface.

• Check for gas bubbles that may form near sensing

surface (due to solution temperature changes). Tap

off gently.

• Avoid large changes in temperature (thermal shock)

as it may damage the sensor.

O-Ring

Additional HI 4113 guidelines

• Remove the protective plastic wrap that covers the

ceramic junction before assembling sensor for the first

time.

• Add reference HI 7078 fill solution to bottom of fill

hole or empty and refill fill solution daily before us-

ing.

• During measurement always operate electrode with

the fill hole open.

• During normal use, fill solution will slowly drain out

of the tapered cone junction at the lower portion of the

electrode. Excessive loss (>4 cm drop within 24 hours)

is not normal. If this occurs verify cap is tightened and

the interface between the internal cone and outer

body is free of debris.

• Add filling solution daily to maintain a good head

pressure. For optimum response, this level should be

maintained and not be allowed to drop more than 2

-3 cm (1-inch) below fill hole.

• Do not use an electrode if crystallized salts are visible

inside the electrode. Drain electrode, disassemble and

rinse internal body with deionized water. Reassemble

and refill with fresh fill solution.

• If an erratic measurement occurs, check to see if for-

eign matter is seen trapped near the internal cone.

Drain by depressing the electrode cap then refill with

fresh fill solution.

VIII.VIII.

VIII.

Electrode PreparationElectrode Preparation

Electrode Preparation

HI 4013

The Hanna HI 4013 is a 2 piece design comprised of a

sensor handle (HI 4000-50) and a sensing module (HI

4013-51). The sensor is shipped with two HI 4013-51

modules.

1. Remove sensing module from shipping vial. Do not

touch the sensing membrane with the “H” hole pat-

tern on it.

2. Screw the module into the sensor handle finger tight.

Do not overtighten.

3. Holding the assembled electrode at the cable end,

shake the sensor to ensure internal fill solution that

may have separated during shipping is in contact

with inner membrane surface.

4. Prepare HI 5315 reference electrode by filling electro-

lyte reservoir with HI 7078 fill solution.

5. Place sensor and reference electrodes into electrode

holder and connect cable connectors to meter.

6. Soak the Nitrate electrodes membrane in a Nitrate

containing standard (0.001M) without ISA before

calibration.

HI 4113

The Hanna HI 4113 is shipped disassembled. The sensor is

shipped with two HI 4113-51 modules.

1. Unwrap Parafilm® seal found over ceramic junction

on inner stem and discard. This is only used for ship-

ping or long term storage.

2. Remove sensing cone from shipping vial. Do not touch

the sensing membrane with the “H” hole pattern on

it.

3. Screw the cone into the inner stem finger tight. Do not

over tighten.

4000-50

4. Rinse inner stem with deionized water making certain

to wet o-ring found on the inner stem.

5. Reassemble electrode by gently pushing the inner

assembly into the outer body, sliding spring down

cable, and screwing cap into place.

6. Remove fill hole cover and o-ring on fill hole spout.

Using the dropper pipette provided, add a few drops

HI 7078 fill solution to the electrode. Invert the elec-

trode to wet the o-ring and rinse the fill solution cham-

ber.

Deionized

Water

Remove

Parafilm

Install

sensing

module

7. Holding the body of the electrode gently press upper

cap with your thumb. This permits the fill solution to

drain out of the body. Release cap and verify elec-

trode returns to its original position. (You may need to

gently assist for this to occur).

8. Tighten the electrode cap onto the body and fill elec-

trode body until fill solution volume is just below fill

hole.

9. Position electrode in a Hanna HI 76404 electrode

holder (or equivalent) and connect BNC connector to

meter.

IX. IX.

IX.

Quick Check of Electrode SlopeQuick Check of Electrode Slope

Quick Check of Electrode Slope

• Connect electrode(s) to pH/mV/ISE meter

• Place meter in mV mode.

• Place 100 mL of deionized water into a beaker with

stir bar.

• Place reference and measuring half-cell or combina-

tion electrode into prepared sample.

• Add 1 mL of a standard to beaker. Record the mV

value when stable.

• Add an additional 10 mL of standard to the

solution. Record the mV when reading has

HI 4113

NITRATE

COMBINATION

stabilized. This value should be less than the

previous value noted (more negative).

• Determine the difference between the two mV values.

An acceptable value for this slope is

56 ± 4 mV (20-25°C)

X. X.

Corrective actionCorrective action

Corrective action

• Verify module has been screwed into sensor handle or

inner stem.

• Verify Parafilm® seal has been removed from ce-

ramic junction (HI 4113 or HI 5315 reference).

• Verify fill solution has been added to reference cham-

ber.

• Verify electrodes are connected properly to meter and

meter is powered.

• Verify dilute standards are freshly made and stored.

Remake solutions if appropriate. Store in plastic

bottles.

• If the reading is jumpy or unstable, shake sensor

down (see section VII).

• If the sensor slope just misses the suggested slope

window, soaking the sensor in a standard solution

without ISA may solve the problem.

• If the membrane is damaged, the response becomes

extremely sluggish, or the slope of the electrode has

decreased significantly, and procedures above have

not helped, the module should be replaced.

For HI 4013

1. Dry off module and sensor handle.

2. Unscrew sensing module and replace with a new one.

(HI 4013-51).

3. Soak new module in nitrate solution to condition it

before calibration.

For HI 4113

1. Drain the fill solution by depressing cap. Rinse elec-

trode with distilled or deionized water. Drain.

2. Unscrew upper cap and slide down cable toward con-

nector.

3. Move spring and outer body down cable also.

4. Dry off inner stem and module with a soft tissue.

5. Hold inner stem and unscrew module and replace

with a new one. (HI 4113-51).

6. Reassemble electrode (see section VII), and refill with

electrolyte. Soak new membrane in nitrate solution

without ISA to condition before calibration.

XI. XI.

XI.

Direct Calibration and MeasurementDirect Calibration and Measurement

Direct Calibration and Measurement

This method is a simple procedure for measuring many

samples. A direct reading ISE meter (HI 4222 or equiva-

lent) determines concentration of the unknown by a direct

reading after calibrating the meter with the standards. Add

HI 4013-00 to adjust ionic strength at a dose of 2 mL per

100 mL sample or standard. ISISA* may also be used at a

dose of 10 mL for 50 mL of sample or standard. The meter

is calibrated using freshly made standards that are in the

measurement range of the unknowns. Unknowns are read

directly. In the region where the electrode calibration be-

comes less linear, more calibration points are needed, and

calibration will need to be repeated more frequently.

A pH/ mV meter in mV mode and semi log graph paper

may also be used. Two or more freshly prepared standards

that are in the measurement range of the unknowns are

measured in mV mode on the meter.

These values are plotted on the semi-log paper and the

points are connected to form a straight-line curve. When

samples are measured, their mV values are converted to

concentration by following the mV to the concentration axis

on the semi-log plot.

*Note: ISISA is the recommended ISA used for procedure

4500-NO

-D. published in Standard Methods for the Ex-

amination of Water and Wastewater and is a EPA accepted

method for drinking water analysis.

Procedure:

Follow sections VIII and IX to prepare electrodes for mea-

surement.

1) Follow section VI to prepare standards/ solution. Stan-

dards should bracket and fall within the range of

interest. Standards and solutions should be at the

same temperature.

• 2 mL of HI 4013-00 is added to 100 mL of both

samples and standards. OR

• 10 mL of ISISA are added to 50 mL both samples

or standards.

Add stir bar and mix before taking measurements.

2) Follow section VII; General Guidelines to optimize test

set-up.

3) During calibration it is best to start with lower concen-

tration samples first. Wait for a stable reading before

reading/ recording values. Permit longer equilibra-

tion times at these levels (3 or 4 minutes).

To prevent carry over and contamination of samples, rinse

sensors with deionized water and remove moisture with

absorbant tissue between samples.

Typical HI 4013 and HI 4113 Linearity

100

150

200

250

300

01234567

-Log of Molar Concentration

XII. XII.

XII.

Other Measurement TOther Measurement T

Other Measurement T

echniquesechniques

echniques

Known additionKnown addition

Known addition

An unknown concentration can be determined by adding a

known volume and concentration of NO

standard to the

sample. mV values are noted before and after the addition

of standard (∆E). An ideal sensor slope can be used in the

equation but actual determined slopes at the temperature

of measurement should be used if known (S). This method

is preprogrammed in the Hanna HI 4222 pH/ISE/mV meter,

which simplifies the method greatly.

Example:

Nitrate ion determination with known addition.

1. A 50 mL sample of unknown (V

SAMPLE

) is placed in a

clean plastic beaker with an electrode (s). Add 50 mL

of ISISA* to sample. Mix. mV 1 is recorded.

2. 5 mL (V

STANDARD

) of 10

-1

M (C

STANDARD

) standard is added

to the beaker and the mV value decreases. (Note: for

other concentration samples, add a known volume

and concentration of standard to produce approxi-

mately 30 mV change).

The unknown Nitrate concentration in the original

sample (C

SAMPLE

) can then be determined by using the

equation that follows.

3. The procedure can be repeated with second standard

addition to verify slope and operation of the method.

sample

)10

∆E/S

- (V

S’

)

standard

sample

S’

sample

standard

ISA

)= V

sample

ISA

)= V

S’

*Note: ISISA is Interferent suppressent ISA see Section IV.

XIIIXIII

XIII.

pH and Interferents pH and Interferents

pH and Interferents

HI 4013/ HI4113 Nitrate electrodes can operate over a pH

range of 3 to 8 but better results are found if pH is kept

constant throughout calibration and test. Sulfuric acid or

NaOH can be used for pH adjustment or use ISISA to surpress

interferences and buffer pH. Limiting the length of time of

exposure to samples containing interferences will prolong

useful life of your electrode. If sensor has been exposed to

ions above recommended levels, soaking in pure nitrate

solutions without ISA will aid recovery of function.

XIV.XIV.

XIV.

Storage and Care of the HI 4013 andStorage and Care of the HI 4013 and

Storage and Care of the HI 4013 and

HI 4113 electrodesHI 4113 electrodes

HI 4113 electrodes

The HI 4013 sensor can be stored in standards that do not

contain ISA for short time periods. For long term storage,

unscrew sensing module from sensor handle and store dry

in the shipping vial.

The model HI 4113 combination electrode can be left in

dilute standards that do not contain ISA for short time

periods. If the electrode will be used frequently and needs

to be ready for use, take measures to prevent evaporation of

fill solution. Top off fill solution, replace o-ring, fill hole

cover on the fill hole opening, and place sensor in dilute

nitrate solution that does not contain ISA. Store electrode

upright. Prior to use, drain electolyte chamber and refill

with fresh HI 7078 fill solution.

For long term storage, the electrode should be drained,

disassembled and washed of salts with deionized water.

Wrap the ceramic junction in Parafilm® or other sealing

wrap. Unscrew the module and store dry in the shipping

vial. Refrigeration of module will extend its life. Store dis-

assembled electrode in storage box provided with electrode.

XV. XV.

XV.

Conversion tablesConversion tables

Conversion tables

For NOFor NO

For NO

Multiply by Multiply by

Multiply by

Moles/L (M) NO

to ppm NO

(mg/L) 62000

ppm (mg/L) to M (moles/L) 1.61 X 10

-5

MAN4113 08/11

WARRANTY WARRANTY

WARRANTY

Hanna Instruments Ion Selective Electrodes are warranted

to be free of defects in material and workmanship for 6

months from date of purchase when used for their intended

purpose and maintained according to instructions. If they

fail to work when first used contact your dealer immediately.

Damage due to accidents, misuse, misapplication, tampering

or lack of prescribed maintenance is not covered.

Hanna Instruments reserves the right to modify the design,

construction or appearance of its products without advance

notice.

Hanna Instruments HI 4013 Owner's manual

Brand: Hanna Instruments

Model: HI 4013

Category: Faucets

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Hanna Instruments HI 4013 Owner's manual

This manual is also suitable for

Hanna Instruments HI 4013 Owner's manual

Related papers

Other documents