Extron IN2013HR User manual

Brand: Extron

Model: IN2013HR

Category: Video switches

Type: User manual

IN2013HR HIGH RESOLUTION VIDEO INTERFACE

FOR 13W3 WORKSTATIONS

IN2013HR

OPERAT ION MANUAL

Installation and Safety Instructions

For Models without a Power Switch:

The socket outlet shall be installed near the equipment and shall be accessible.

For all Models:

No serviceable parts inside the unit. Refer service to a qualified technician.

For Models with Internal or External Fuses:

For continued protection against fire hazard, replace only with same type and rating of fuse.

Instructions d’installation et de sécurité

Pour les modèles sans interrupteur de courant:

La prise de courant d’alimentation sera installé près de l’équipement et sera accessible.

Pour tout les modèles:

Pas de composants à entretenir à l’intérieur. Confiez toute réparation à un technicien qualifié.

Pour les modèles équipés de fusibles internes ou externes:

Afin d’éviter tout danger d’incendie, ne remplacer qu’avec le même type et la même valeur de fusible.

Installations- und Sicherheitshinweise

Für Geräte ohne Netzschalter:

Die Netzsteckdose soll in der Nähe des Gerätes installiert und frei zugänglich sein.

Für alle Geräte:

Keine Wartung innerhalb des Gerätes notwendig. Reparaturen nur durch einen Fachmann!

Für Geräte mit interner oder externer Sicherung:

Für dauernden Schutz gegen Feuergefahr darf die Sicherung nur gegen eine andere gleichen Typs und gleicher Nennleistung

ausgewechselt werden.

Instalacion E Instrucciones de Seguridad

Modelos Sin Interruptor:

La conexión debe ser instalada cerca del equipo y debe ser accesible.

Para Todos Los Modelos:

Dentro de la unidad , no hay partes para reparar. Llame un tecnico calificado.

Modelos con Fusibles Internos o Externos:

Para prevenir un incendio, reemplace solo con el mismo tipo de fusible.

CE COMPLIANCE

All products exported to Europe by Inline, Inc. after January 1, 1997 have been tested and found to

comply with EU Council Directive 89/336/EEC. These devices conform to the following

standards:

EN50081-1 (1991), EN55022 (1987)

EN50082-1 (1992 and 1994), EN60950-92

Shielded interconnect cables must be employed with this equipment to ensure compliance with

the pertinent Electromagnetic Interference (EMI) and Electromagnetic Compatibility (EMC)

standards governing this device.

FCC COMPLIANCE

This device has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide against harmful

interference when equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of

equipment in a residential area is likely to cause harmful interference, in which case the user will be

required to correct the interference at their own expense.

Product Overview

DESCRIPTION

The IN2013HR is a high performance dedicated computer video interface for Sun, SGI, IBM

PowerPC, NeXT, and other graphic workstations with 13W3 video ports. Like other INLINE

interfaces, the IN2013HR performs the following functions:

• Signal Splitting - allows the simultaneous connection and viewing of both the

computer’s local monitor and a second output device such as a large screen data projector

or presentation monitor.

• Physical Interfacing and Adaptation - Because computers employ many different

types of video output connectors, it is sometimes difficult to directly connect them to

data projection devices. The IN2013HR connects to workstations with special video

connectors (13W3) and provides an output signal on standard BNC connectors.

• Electronic Interfacing - The interface accepts video in a wide variety of sync formats

and converts the signal to RGsB, RGBS, RGBHV or Composite Monochrome as

required by the display device, cabling, and video routing system.

PRODUCT FEATURES

Universal Compatibility for Graphic Workstations with 13W3 Video Ports - Factory set for

automatic operation with Sun and SGI computers, the unit will accept other workstation signals

by adjusting one or two dipswitches.

Exceptional Video Performance - Featuring advanced video amplification circuitry, the

IN2013HR offers a video bandwidth of 230 MHz, ensuring that even the highest resolution

workstation video signals will be interfaced with complete signal clarity.

Local Monitor Output - provides a buffered signal for the local computer monitor.

Automatic Output Sync Format Selection - The IN2013HR senses the number of cables

connected to the outputs at power up and automatically sets the output sync format to RGsB,

RGBS, RGBHV or Composite Monochrome.

Dual Outputs - the IN2013HR can drive two display devices in addition to the local monitor.

Flexible Monitor Emulation - The interface automatically sets itself to the appropriate

resolution / refresh rate, or can be used without a local display device (dipswitches are provided

to emulate virtually any monitor).

Convenient Controls - The IN2013HR offers intuitive front panel controls for the most

important signal adjustments.

• Gain Control - adjusts the voltage level of the RGB components simultaneously

(ensuring that gray scale is maintained), and may be used to compensate for signal loss

due to long cable runs.

• Sharpness Control - provides effective image enhancement for high-resolution video

signals by increasing clarity and edge detail.

• Horizontal Position Control - allows the picture to be centered precisely on the data

display screen.

The IN2013HR is not a scan converter. The data projector, monitor or

other output device must be compatible with the horizontal scan rate,

vertical scan rate and resolution output by the computer video card.

Compatibility

INPUT

The IN2013HR will accept high-resolution video signals from Sun SPARC, Silicon Graphics,

IBM PowerPC, NeXT and virtually any other graphic workstation that outputs analog video

through a 13W3 female connector. Input signal compatibility parameters are:

Video Signal: Analog RGB Video

Connector: 13W3 female video port on computer

Signal format: RGsB, RGBS, RGBHV

Horizontal Frequency Range: 30 KHz to 130 KHz

Vertical Refresh Rates: 50 Hz to 120 Hz

OUTPUT

The IN2013HR outputs an analog RGsB, RGBS, RGBHV or Composite Monochrome signal on

female BNC connectors. This output signal is compatible with high-resolution data grade

monitors and data / graphics projectors. Graphic workstations operate in several video modes

encompassing a wide range of resolutions and scan rates. Many workstation video signals run as

high as 70 KHz or more, with the newest workstations offering output resolutions as high as

1920 x 1080. The data projector or monitor connected to the interface output must be compatible

with the horizontal scan rate and vertical refresh rate of the computer’s video signal. Check the

documentation for both the computer graphics card and the data display device to ensure

compatibility.

Installation

This section offers step-by-step instructions for installing the IN2013HR Computer Video

Interface. An Application Diagram is included on page 5.

1. Turn the Computer and Computer Monitor Off - Disconnect the computer monitor from

the computer’s video port.

2. Connect the Permanently Attached IN2013HR Input Cable - to the computer’s video output

port (see illustration on the right). For cable

runs that are longer than 3’, the IN8400

Series 13W3 Workstation Extension Cables

are available in lengths ranging from 6’ to

50’.

3. Check the Input Signal Configuration Settings - (SWITCH 1 - Dipswitches 8 / 9 / 10)

which are on the bottom of the IN2013HR. The factory default settings for dipswitches 8, 9

and 10 will work with Sun workstations and most SGI computers. For other computers,

carefully set dipswitches 8, 9 and 10 as indicated in the chart below:

Note: These settings only relate to the input signal from the computer and have no effect on the

output sync format.

Computer Input Selection Dipswitch Chart

Workstation Input Signal 8/9/10 Dipswitch Setting - Switch Bank 1

RGBS (most common) 000 - Composite Sync on pin 5

SUN

RGBHV 101 - Hor. sync on pin 6; Vert. sync on pin 2

RsGsBs (most common) 001 - Sync on green

RGBS 011 - Composite Sync on pin 3

SGI

RGBHV 100 - Hor. sync on pin 4; Vert. sync on pin 5

NeXT Color

RGsB 001 - Sync on green

IBM PowerPC

RGBHV 010 - Hor. sync on pin 5; Vert. sync on pin 9

4. Connect the IN2013HR Video Output - (5 BNC connectors) to the data display device's

RGB input, using three, four, or five high-resolution BNC cables or a multi-conductor

RGBHV, RGBS, or RGB "snake". The IN7000 Series, IN7200 Series, IN7300 Series and

IN7400P Series high-resolution cables are well suited for this purpose. Take care while

making connections to insure that the red output is connected to the red input, green output to

the green input, etc.

5. Select the Output Sync Format - The interface normally selects an output format

automatically according to the number of cables connected to the output. If you wish to

override the automatic output format feature and manually select a specific format, set the

dipswitches as necessary according to the chart on page 8 (see Output Sync Format -

Manual Mode).

6. Connect the Local Computer Monitor - (if present) to the IN2013HR local monitor output

port. Check the Monitor Emulation Dipswitch Settings on the bottom of the IN2013HR.

• When Using a Local Monitor - make sure that all dipswitches in the box labeled

MONITOR EMULATION are set to “0”.

• If No Local Monitor is Required - using the IN9339 alignment tool (provided), gently

set the monitor emulation dipswitches according to the Monitor Emulation Dipswitch

Chart provided on page 9.

Check the Monitor Emulation chart and dipswitch settings carefully. Any

improper setting of the emulation dipswitches may lead to improper

operation and could even result in severe damage to the computer video

port or the monitor. If you are in doubt as to which monitor emulation to

choose, set all the Monitor Emulation dipswitches to “0” and connect the

local monitor.

6. Apply Power - to the IN2013HR using the IN9230 IEC power cable (included).

7. Turn On - the computer, the IN2013HR, the local monitor (if applicable) and the display

device. If necessary, adjust the gain, sharpness and / or horizontal position control as

detailed on pages 6 and 7.

Front Panel Controls

The IN2013HR features fully automatic operation, however, the interface offers several external

controls that allow users to optimize the unit’s performance to meet the needs of specialized

applications. Gain, sharpness and horizontal position control adjustments are located on the

front of the IN2013HR. Turning the adjustments clockwise will increase the value, and

counterclockwise will decrease it. Each control has an adjustment range of 15 turns.

GAIN CONTROL

The gain control is a small black knob located on the left side of the unit’s front panel. The gain

control adjusts the output voltage of the red, green, and blue outputs simultaneously (ensuring

that gray scale is maintained), and may be used to compensate for signal loss due to long cable

runs. The gain adjustment range is .7 in the minimum position (30% decrease) and 1.3 in the

maximum position (30% increase). The factory default setting is 1.0 (unity gain).

SHARPNESS CONTROL

The IN2013HR sharpness / peaking circuitry provides variable high frequency equalization that

can compensate for high frequency losses due to long output cable runs. The amount of high

frequency boost required will vary depending on the length and bandwidth performance of the

video output cables, and, to a lesser extent, the resolution and frequency of the input signal.

When using short output cables, the sharpness control should usually be placed at the minimum

setting to avoid over-peaking.

The sharpness control is located between the gain control knob and the local monitor output port.

Using the IN9339 Alignment Tool (included), turn the sharpness control clockwise to increase

the sharpness setting, and counterclockwise to decrease the sharpness setting. The factory

default setting is minimum (no sharpness / peaking enhancement). The following guidelines are

useful in selecting the optimal sharpness / peaking setting:

If the image is soft and / or fine details in the picture lack clarity:

The sharpness is probably set too low. Increase the sharpness control setting.

If a white, ghosted image appears to the right side of the lines / characters:

The sharpness is probably set too high (over-peaked). Decrease the sharpness control

setting.

HORIZONTAL POSITION CONTROL

The horizontal position control is a small black knob located adjacent to the front panel power

LED display. This adjustment allows users to shift the position of the image on the data display

device from left to right. The horizontal position control does not effect the local monitor.

If the horizontal position adjustment is set to an extreme position on either the display device or

the IN2013HR, the output image may appear dark and / or the colors may be displayed

improperly. To position the video image and achieve optimum picture quality:

1. Set the display device’s horizontal position control to the center of its adjustment range.

2. Adjust the horizontal position control on the IN2013HR until the picture is centered

properly on the display device.

Horizontal Position Control Enable / Disable

The factory default setting is horizontal position control enabled. In rare cases (depending on the

design of the display device sync circuitry), you may have to disable the horizontal position

control to achieve a solid image on the display device. The horizontal position control may be

enabled or disabled by setting the dipswitch 1 in SWITCH Bank 1 as indicated in the chart at the

bottom of the page.

Dipswitch Settings

Two dipswitch panels are easily accessed through windows on the bottom of the IN2013HR. The

SWITCH 1 panel regulates the output sync format (dipswitches 1-7) and controls the input signal

configuration (dipswitches 8-10). The SWITCH 2 panel determines the monitor emulation settings.

SWITCH 1

For most installations, the IN2013HR will be operated in the factory default mode and will not

require any changes to the dipswitch settings. The factory default settings are:

SWITCH 1 Dipswitches ON: 1, 3, 5, 6, 7 & 8

Output Signal Format: Auto Sense Enabled - Interface Selects Format

Horizontal Position Control: Enabled

H & V Sync Polarity: Mirror Input Polarities

Monitor Emulation (SWITCH 2): Disabled (all Dipswitches on SWITCH 2 panel are set to 0)

The following table lists the functions of the first 7 dipswitches in SWITCH 1:

Dipswitch Function Setting

Horizontal Position Control

1 = Enabled*

0 = Disabled

Output Sync Format:

Sync on Green

1 = Sync on Green

0 = RGBHV / RGBS*

Output Sync Format

RGBHV / RGBS

1 = RGBHV*

0 = RGBS

Output Sync Polarity

1 = Forced Negative

0 = Mirror Input*

Output Sync Format:

Auto Sense / Manual

1 = Auto Sense*

0 = Manual

Serration Pulses

1 = Serrations Present*

0 = No Serrations

Output Video Format:

Green / Monochrome Video

1 = Green*

0 = Monochrome on Green BNC

*Factory Default Settings

OUTPUT SIGNAL FORMAT SELECTION

Output Format: Automatic Sense Mode (Dipswitch 5 = 1)

In factory default configuration, the IN2013HR automatically senses the number of cables connected

to the output BNC connectors and selects an appropriate output signal format. LED indicators located

next to the V/Sync, H/Comp Sync and Green output BNCs (on the back of the interface) provide clear

visual confirmation of the current output sync format. In order for output format auto sense circuit to

operate, dipswitch 5 on Switch Bank 1 must be set to 1.

Number of Cables Connected to Output Output Format

(3) Cables connected to RGB BNCs RGsB

(4) Cables connected to RGBS BNCs RGBS

(5) Cables connected to RGBHV BNCs RGBHV

Output Sync Format : Manual Mode (Dipswitch 5=0)

For some applications, you may wish to force the interface to operate in a specific output format.

To set the output sync format manually, you must first disable the auto sense circuit by setting

dipswitch 5 on Switch Bank 1 to 0. Next, set dipswitches according to the table below to select

the desired output format.

Output Format Dipswitch Settings

(Switch Bank 1)

RGBHV (Factory Default) 2 = 0

3 = 1

5 = 0

RGBS 2 = 0

3 = 0

5 = 0

RGsB 2 = 1

3 = 1

5 = 0

7 = 1

Composite Monochrome on Green BNC 2 = 1

3 = 1

5 = 0

7 = 0

INPUT SIGNAL FORMAT SELECTION

The IN2013HR is set at the factory for automatic operation with SUN and most SGI computers

(*dipswitches 8 / 9 / 10 off). For other computers or signal formats, carefully set dipswitches 8, 9 and

10 as indicated in the chart below

INPUT SIGNAL CONFIGURATION - SWITCH BANK 1

DIPSWITCH SUN

RGBS*

SUN

RGBHV

SGI / NeXT

RsGsBs

SGI

RGBS

SGI

RGBHV

IBM

POWER

8 0 1 0 0 1 0

9 0 0 0 1 0 1

10 0 1 1 1 0 0

*Factory Default Settings

SWITCH 2 (MONITOR EMULATION)

The IN2013HR includes a bank of 10 dipswitches (SWITCH 2) on the bottom side of the interface for

monitor emulation. Setting the dipswitches to the appropriate positions allows the unit to emulate the

appropriate sense signals, thus setting the video card to the desired frequency, refresh rate and resolution,

even without a local monitor. When configured properly, the interface can emulate virtually any type of

monitor.

Using the IN2013HR with a Local Monitor

Many high-resolution graphic workstations use sense signals to set resolution, horizontal frequency and

vertical refresh rate. The IN2013HR passes all sense pins between the computer video port and the Local

Monitor, ensuring that the computer can sense the attached monitor and set itself to an appropriate

resolution and scan rate for that device. The Monitor Emulation dipswitches must all be set to “0”

when using a local monitor. This allows all sense pins to pass through, ensuring proper operation of

the graphics card and monitor.

Using the IN2013HR without a Local Monitor - The IN2013HR’s design makes it easy to use the

interface without a local monitor. Because the Local Monitor Output port is buffered, there is no need for a

termination plug to terminate the video signals when used without a local display device. If you are not

using a local monitor, but need to emulate a specific mode, locate your workstation type and desired mode

in the chart at the bottom of the page. If you are not sure of the exact mode to select for your computer,

select the setting shown in bold since it is the most common mode. Using the IN9339 Alignment Tool

(provided), gently set the dipswitches to the appropriate settings.

Check the Monitor Emulation chart and the IN2013HR dipswitch settings

carefully. An improper setting of the emulation dipswitches may lead to

improper operation and could even result in severe damage to the computer

video port or the monitor. Some modes listed on the following page may not be

supported by certain workstations / graphics cards.

Monitor Emulation Dipswitch Chart

Make / Model Dipswitch Settings

SUN

1152x900 / 66 Hz / 61.8 KHz

0011000000

1152x900 / 76 Hz / 71.7 KHz - 16” / 17” Monitor 1001000000

1152x900 / 76 Hz / 71.7 KHz - 19” Monitor 1001000100

1280x1024 / 76 KHz / 81 KHz 1011000000

1600x1280 / 76 Hz / 100.8 KHz 0011000100

SGI

Single Scan 15” (Indy) 1024x768 / 60 Hz / 48.48 KHz 0100000000 or

0100000010

Single Scan 19” (Personal Iris / 4D) 1280x1024 / 60 Hz / 63.9 KHz 0000000000

Hitachi 19” 1280x1024 / 60 Hz 0100011000

Dual Scan 16” (Original Indigo) 1280x1024 & 1024x768 / 60 Hz / 63.9 &

48.48 KHz

0000010000

Dual Scan 19” (Original Indigo) 1280x1024 & 1024x768 / 60 Hz / 63.9 &

48.48 KHz

0100010000

Multiscan 16” Up to 1280x1024 / 76 Hz / 30 - 82 KHz 0100001000 or

0100001010

Multiscan 19” Up to 1280x1024 / 76 Hz / 30 - 82 KHz

0000011000 or

0000011010

Multiscan 21” Up to 1280x1024 / 76 Hz / 30 - 82 KHz 0000001000

Specifications

IN2013HR Computer Video Interface

Input

Connector type (1) 13W3 male

RGB Video Signals Analog, 0.7 Vp-p Nominal

Input Impedance 75 Ohms

Sync Signals TTL compatible

Horizontal Scan Range 15 KHz - 135.0 KHz

Vertical Scan Range 50 Hz - 120 Hz

Local Monitor Output

Connector Type

(1) 13W3 female connector, buffered output,

sync format same as input

Data Display Outputs

Connector Type 2 Sets of (5) BNC female

Output Signal Formats RGsB, RGBS, RGBHV, Composite Monochrome

RGB Signals Analog Video, 75 ohm impedance

Bandwidth 230 MHz @ -3 dB

Rise and Fall Times 1.5 nano seconds

Video Gain (Terminated) Variable Control - Adjustable from .7 (30% voltage

decrease) to 1.3 (30% voltage increase)

Sync Signal

H, V and S: 5V unterminated and 2Vp-p 75 ohm terminated

Sync on Green: 0.3 Vp-p 75 Ohm terminated

Horizontal Pulse Width

30 KHz - 40 KHz: 1.5 µSec

> 40 KHz: 0.7 µSec

Vertical Pulse Width

Same as the input for H & V,

§µSec for Sync on Green or Composite Sync

Controls

External

Horizontal Position, Video Gain, Sharpness,

Output Sync, Input Computer Select, Monitor Emulation

Dimensions

Size 1.75" x 11.75" x 6.5" / 4.4cm x 29.9cm x 16.5cm

Product Weight 2 lb. / 1kg.

Shipping Weight 5 lb. / 2.5kg.

Power

Power Supply Internal Switch Mode: 90 - 260 VAC; 0.29A; 47 - 63 Hz

Power Consumption 14.5 Watts

Regulatory Compliance

Safety & EMI

UL 1950, CAN/CSA-22.2 No. 950 3

Ed.

FCC class A; CE: EN50022 (1987), EN50081-1 (1991),

EN50082-1 (1992 & 1994), EN60950-92

Parts Included

(1) IN2013HR: Interface

(1) IN9230: IEC Power Cable (U.S. only)

(1) IN9333: Alignment Tool

(1) Operation Manual

Optional Accessories

Extension Cables

IN8400 Series: 13W3 Workstation Extension Cable (available in lengths from 6’ to 50’)

RGB Installation Cables

Coaxial Cables 3-Conductor 4-Conductor 5-Conductor

Standard Resolution

IN7000-4 IN7000-5

Standard Resolution, Plenum

IN7000P-4 IN7000P-5

Super High Resolution

IN7300-3 IN7300-4 IN7300-5

Super High Resolution, Plenum

IN7400P-5

Ultra High Resolution

IN7200-3 IN7200-5 IN7200-6

All cable grades are available in lengths from 3’ to 250’ pre-terminated with high quality BNC connectors or as bulk cable.

Troubleshooting

Problem: There is no image on the display device.

 Solution 1: Make sure that the IN9230 IEC power cable is securely plugged into the

unit and the A/C source.

 Solution 2: Make sure the A/C source is live.

 Solution 3: Verify that the power switch is turned on for the video source, the

IN2013HR and the display device.

 Solution 4: Verify the connections to the video source and the output display device(s).

Problem: The power switch is turned on, but the front panel LED is dark.

 Solution 1: Make sure that the IN9230 IEC power cable is securely plugged into the

unit and the A/C source.

 Solution 2: Make sure the A/C source is live.

 Solution 3: The IN2013HR contains a 0.5A / 250V time delay fuse. To change the

fuse, first remove power from the unit and then slide out the fuse holder (located on the

rear panel between the power switch and the IEC cable receptacle) using the IN9339

Alignment Tool (included).

Problem: The display device connected to the IN2013HR output has a bad / scrambled

image.

 Solution 1: Check the dipswitch settings to make sure the unit is outputting a sync

format that is compatible with the display device. For most applications the default

dipswitch settings will work best (see page 7).

 Solution 2: The RGB cable may have a bad sync line. Try switching connections on the

output to verify that the bad color’s cable is OK (Example: If there is no red, try running

the green output through the red cable and see if green is displayed or not.)

 Solution 3: The display device connected to the IN2013HR may not be compatible with

the computer output. Adjust the output resolution of the computer video card

accordingly.

Problem: The output image is very dark.

 Solution: The horizontal position control may be set to an extreme position or may be

interacting poorly with the horizontal position control on the display device. Follow the

horizontal position adjustment procedure on page 6.

Problem: The output image is missing a color.

 Solution: The RGB cable may be damaged / defective. Try switching connections on

the output to verify that the bad color’s cable is OK (Example: If there is no red, try

running the green output through the red cable and see if green is displayed or not.)

Problem: The output image is very bright and appears “overdriven” with poor contrast.

 Solution 1: Verify the gain setting on the IN2013HR. If it is set to a very high level,

reduce the gain control setting as required.

 Solution 2: Check the contrast and brightness settings on the display device. Many

display devices look best with the contrast set toward the upper end of the adjustment

range (75 - 95%) and the brightness set towards the middle of the adjustment range (40 -

60%).

Problem: The output image is green.

 Solution: The dipswitches may be set for Sync on Green output. Not all data displays

operate well with an RGsB signal. Try changing the dipswitches to factory default so the

unit outputs an RGBHV signal (see page 7).

Problem: The output image is doubled, with two images displayed side-by-side.

 Solution: The display device may not be compatible with the horizontal scan rate of the

computer.

If problems persist, call INLINE Technical Services at (714) 921-4100 for further assistance.

Warranty

♦

INLINE warrants the equipment it manufactures to be free from defects in materials and

workmanship.

♦

If equipment fails because of such defects and INLINE is notified within two (2) years

from the date of shipment, INLINE will, at its option, repair or replace the equipment at

its plant, provided that the equipment has not been subjected to mechanical, electrical or

other abuse or modifications.

♦

Equipment that fails under conditions other than those covered will be repaired at the

current price of parts and labor in effect at the time of repair. Such repairs are warranted

for ninety (90) days from the day of re-shipment to the Buyer.

♦

This warranty is in lieu of all other warranties expressed or implied, including

without limitation, any implied warranty or merchantability or fitness for any

particular purpose, all of which are expressly disclaimed.

The information in this manual has been carefully checked and is believed to be accurate. However,

INLINE, Inc. assumes no responsibility for any inaccuracies that may be contained in this manual. In

no event will INLINE, Inc. be liable for direct, indirect, special, incidental, or consequential damages

resulting from any defect or omission in this manual, even if advised of the possibility of such

damages. The technical information contained herein regarding IN2013HR features and specifications

is subject to change without notice.

IBM PowerPC is a trademark of International Business Machines. Sun, Sun Microsystems, and the

Sun Logo are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and

other countries. SGI is a trademark of Silicon Graphics, Inc. All other trademarks and registered

trademarks are the property of their respective companies.

INLINE, INC.

♦

810 West Taft

♦

Orange, CA 92865

800-882-7117

♦

714-450-1800

♦

FAX 714-450-1850

♦

www.inlineinc.com

Extron IN2013HR User manual

Brand: Extron

Model: IN2013HR

Category: Video switches

Type: User manual

Download PDF

report

Extron IN2013HR User manual

Extron IN2013HR User manual

Related papers

Other documents