LG LG M2262DP-PZ User manual

www.lg.com

OWNER’S MANUAL

MONITOR TV

MONITOR TV MODELS

M1962DP

M2062DP

M2262DP

M2362DP

M2762DP

Please read this manual carefully before operating

your set and retain it for future reference.

ENGLISH

CONTENTS

2

PREPARATION

FRONT PANEL CONTROLS ..............................4

BACK PANEL INFORMATION ............................5

STAND INSTALLATION ......................................6

DETACHING STAND ..........................................8

DETACHING STAND BODY .............................10

WALL MOUNT : HORIZONTAL INSTALLATION .......11

DESKTOP PEDESTAL INSTALLATION ...........12

POSITIONING YOUR DISPLAY .......................12

SWIVEL STAND(Only M2762DP) .....................13

LOCATION ........................................................13

SECURING THE SET TO THE WALL TO

PREVENT FALLING WHEN THE SET IS USED

ON A STAND (Only M2762DP) .........................14

ATTACHING THE TV TO A DESK (Only

M2762DP) .........................................................15

KENSINGTON SECURITY SYSTEM ...............16

EXTERNAL EQUIPMENT SETUP

ANTENNA CONNECTION ................................17

HD RECEIVER SETUP ....................................18

DVD SETUP ......................................................21

VCR SETUP ......................................................24

INSERTION OF CI MODULE ...........................26

DIGITAL AUDIO OUT SETUP...........................27

USB SETUP ......................................................28

HEADPHONE SETUP ......................................29

PC SETUP ........................................................30

BACK COVER FOR WIRE ARRANGEMENT ..33

SUPPORTED DISPALY RESOLUTION ...........34

WATCHING TV / PROGRAMME

CONTROL

REMOTE CONTROL KEY FUNCTIONS ..........36

TURNING ON THE TV .....................................38

PROGRAMME SELECTION .............................38

VOLUME ADJUSTMENT ..................................38

QUICK MENU ...................................................39

ON SCREEN MENUS SELECTION AND

ADJUSTMENT ..................................................40

AUTO PROGRAMME TUNING ........................41

CABLE DTV SETTING (IN CABLE MODE ONLY) ....46

MANUAL PROGRAMME TUNING

(IN DIGITAL MODE) .................................47

MANUAL PROGRAMME TUNING

(IN ANALOGUE MODE) ...........................49

PROGRAMME EDIT .........................................51

IN DTV/RADIO MODE ......................................52

IN TV MODE .....................................................52

SOFTWARE UPDATE ......................................54

DIAGNOSTICS .................................................56

CI [COMMON INTERFACE] INFORMATION ...57

SELECTING THE PROGRAMME LIST ............58

FAVOURITE PROGRAMME SETUP ................59

INPUT LIST .......................................................60

EPG (ELECTRONIC PROGRAMME

GUIDE)(IN DIGITAL MODE)

Switch on/off EPG .............................................61

Select a programme ..........................................61

Button Function in NOW/NEXT Guide Mode ...62

Button Function in 8 Day Guide Mode .............62

Button Function in Date Change Mode ............63

Button Function in Extended Description Box ..63

Button Function in Record/Remind Setting Mode ........64

Button Function in Schedule List Mode ............64

PICTURE CONTROL

PICTURE SIZE (ASPECT RATIO) CONTROL .......65

PICTURE WIZARD ...........................................67

ꕊ ENERGY SAVING .......................................68

PRESET PICTURE SETTINGS ........................69

MANUAL PICTURE ADJUSTMENT .................70

PICTURE IMPROVEMENT TECHNOLOGY ....71

EXPERT PICTURE CONTROL ........................72

PICTURE RESET .............................................75

SCREEN SETUP FOR PC MODE ...................76

SOUND CONTROL

AUTO VOLUME LEVELER ...............................81

CLEAR VOICE II ...............................................82

BALANCE ..........................................................83

CONTENTS

3

PRESET SOUND SETTINGS-SOUND MODE ......84

PRESET SOUND SETTINGS-USER MODE ...85

Surround X ........................................................85

AUDIO RESET ..................................................86

DIGITAL AUDIO OUT ........................................87

TV SPEAKERS ON / OFF SETUP ...................88

DTV AUDIO SETTING

(IN DIGITAL MODE ONLY) ......................89

I/II

Stereo/Dual Reception

(In Analogue Mode Only) ...................90

NICAM Reception

(In Analogue Mode Only) ...................91

Speaker Sound Output Selection .............91

TIME SETTING

CLOCK SETUP .................................................92

AUTO ON/OFF TIME SETTING .......................93

SLEEP TIMER SETTING ..................................94

AUTOMATIC STNADBY SETTING ..................94

OPTION SETTING

ON-SCREEN MENU LANGUAGE / COUNTRY

SELECTION ......................................................95

LANGUAGE SELECTION

(IN DIGITAL MODE ONLY) ......................96

AUDIO DESCRIPTION

(IN DIGITAL MODE ONLY) ......................97

DATA SERVICE .................................................98

INPUT LABEL ...................................................99

POWER INDICATOR ......................................100

DEMO MODE ..................................................101

MODE SETTING .............................................102

INITIALIZING(RESET TO ORIGINAL FACTORY

SETTINGS) .........................................................103

PARENTAL CONTROL / RATINGS

SET PASSWORD & LOCK SYSTEM .............104

BLOCK PROGRAMME ...................................105

PARENTAL CONTROL (IN DIGITAL MODE

ONLY) ..............................................................106

INPUT BLOCK ................................................107

KEY LOCK ......................................................108

TO USE A USB DEVICE

WHEN CONNECTING A USB DEVICE..........109

PHOTO LIST ................................................... 111

MUSIC LIST ....................................................117

MOVIE LIST ....................................................121

DIVX REGISTRATION CODE ........................128

DEACTIVATION ..............................................129

TELETEXT

SWITCH ON/OFF ...........................................130

SIMPLE TEXT .................................................130

TOP TEXT .......................................................130

FASTEXT ........................................................131

SPECIAL TELETEXT FUNCTION ..................131

DIGITAL TELETEXT

TELETEXT WITHIN DIGITAL SERVICE ........132

TELETEXT IN DIGITAL SERVICE ..................132

APPENDIX

TROUBLESHOOTING ....................................133

MAINTENANCE ..............................................137

PRODUCT SPECIFICATIONS .......................138

IR CODES .......................................................143

EXTERNAL CONTROL DEVICE SETUP

RS-232C Setup .......................................144

Type of Connector; D-Sub 9-Pin Male ....144

RS-232C Configurations .........................144

Set ID .......................................................145

Communication Parameters ....................146

4

PREPARATION

FRONT PANEL CONTROLS

■ This is a simplified representation of the front panel. The image shown may be somewhat different

from your set.

Headphone Jack

IR receiver (Remote controller receiver)

INPUT Button

MENU Button

OK Button

VOLUME Button

PROGRAMME Button

Power Button

Power Indicator

Illuminates blue when the set is switched on.

Note: You can adjust Power indicator in the OPTION menu.

1

5

3

7

2

6

4

8

9

2

3 4 5 6 7 8

9

5

PREPARATION

■ This is a simplified representation of the front panel. The image shown may be somewhat different from your

set.

BACK PANEL INFORMATION

PCMCIA (PERSONAL COMPUTER MEMORY CARD

INTERNATIONAL ASSOCIATION) CARD SLOT

Insert the CI Module to PCMCIA CARD SLOT.

(This feature is not available in all countries.)

HDMI/DVI INPUT

Connect a HDMI signal to HDMI IN.

Or DVI (VIDEO) signal to HDMI IN with DVI to HDMI

cable.

RGB/DVI AUDIO INPUT

Connect the audio from a PC.

OPTICAL DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.

Connect to a Digital Audio Component.

Use an Optical audio cable.

USB Input

Euro Scart Socket (AV IN)

Connect scart socket input or output from an external

device to these jacks.

Power Cord Socket

This set operates on AC power. The voltage is indi-

cated on the Specifications page. Never attempt to

operate the set on DC power.

RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC.

This port is used for Service or Hotel mode.

COMPONENT INPUT

Connect a component video/audio device to these

jacks.

RGB INPUT (PC)

Connect the output from a PC.

ANTENNA / CABLE INPUT

Connect over-the-air signals to this jack.

1

5

6

7

8

9

10

11

2

3

4

1

2

3 4 5 6

7 9

1110

8

6

PREPARATION

STAND INSTALLATION

■ The image shown may be somewhat different from your set.

Carefully place the product screen side down

on a cushioned surface that will protect prod-

uct and screen from damage.

Insert the Stand Base into the product.

Turn the Stand Base Lock through 90° to fix the Stand Base to the Stand Body.

1 2

3

4 5

Stand Base

Base Lock

7

PREPARATION

STAND INSTALLATION

■ The image shown may be somewhat different from your set.

Carefully place the product screen side down on a

cushioned surface that will protect product and

screen from damage.

Insert the stand base into the product.

Use a Coin on the bottom of the stand base

and turn the screw clockwise to tighten.

1

2

3

Stand Base

Coin

8

PREPARATION

DETACHING STAND

■ The image shown may be somewhat different from your set.

Place the set screen side down on a cushion

or soft cloth.

Detach the monitor to the Stand Base by

turning the screw to the left.

Turn the Stand Base Lock through 90° to separate the Stand Base from the Stand Body.

Pushing Latch inside, Take the stand base from stand body.

1 2

3

4

Latch

9

PREPARATION

DETACHING STAND

■ The image shown may be somewhat different from your set.

1

2

3

Place the set screen side down on a cushion or soft

cloth.

Pull the stand base.

Detach the monitor to the Stand Base by turning the

screw to the left.

Turn the screw by using a Coin.

Coin

10

PREPARATION

DETACHING STAND BODY

■ The image shown may be somewhat different from your set.

■ Remove the Stand Body in the same way as the following when using it as a Wall Hook.

1. Remove the screw 2 point.

2. Pull the stand body.

1. Remove the screw 4 point.

2. Pull the stand body.

11

PREPARATION

WALL MOUNT : HORIZONTAL INSTALLATION

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation

instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and

Setup Guide.

If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.

When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.

1. Be sure to use screws and a wall mount that meet VESA standards.

2. Using screws longer than those recommended might damage the product.

3. Using screws that do not meet VESA standards might either damage the product or result in it coming

away from the wall. We will not be held responsible for any damage resulting from failure to follow these

instructions.

4. VESA compatible only with respect to screw mounting interface dimensions and mounting screw speci-

fications

5. Please use VESA standard as below.

5-1) 784.8 mm (30.9 inch) and under

* Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm

5-2) 787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad and screws.

10 cm

10 cm 10 cm

10 cm

Wall Mount Pad

< Screw Mounting Interface Dimensions >

Model

M1962DP

M2062DP

M2262DP

M2362DP

M2762DP

VESA ( A x B) 100 x 100 200 x 100

Wall mount

bracket(optional)

RW120 RW240

12

PREPARATION

DESKTOP PEDESTAL INSTALLATION

POSITIONING YOUR DISPLAY

For proper ventilation, allow a clearance of 10 cm on each side and from the wall.

■ The image shown may be somewhat different from your set.

Adjust the position of the panel in various ways for maximum comfort.

* Tilt range

-5°

15°

10 cm

10 cm 10 cm

13

PREPARATION

LOCATION

■ When adjusting the angle of the screen, do not put your

finger(s) in between the head of the monitor and the stand

body.

You can hurt your finger(s).

Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to

expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a

position to allow a free flow of air. Do not cover the ventilation openings on the back cover.

WARNING

SWIVEL STAND(Only M2762DP)

■ The image shown may be somewhat different from your set.

After installing the set, you can adjust the set manually to the left or right direction by 179 degrees to

suit your viewing position.

14

PREPARATION

SECURING THE SET TO THE WALL TO PREVENT FALLING

WHEN THE SET IS USED ON A STAND (Only M2762DP)

■ The image shown may be somewhat different from your set.

■ Use a sturdy rope or cord (sold separately) to tie the product. It is

safer to tie the rope so it becomes horizontal between the wall and

the product.

We recommend that you set up the set close to a wall so it cannot fall over if pushed backwards.

Additionally, we recommend that the set be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.

Caution: Please make sure that children don’t climb on or hang from the set.

■ Insert the eye-bolts (or set brackets and bolts) to tighten the product to the wall as shown in the picture.

* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

* Insert the eye-bolts or set brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is

mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

NOTE

►When moving the set, undo the cords first.

► Use a platform or cabinet strong enough and large enough to support the size and weight of the set.

► To use the set safely make sure that the height of the bracket on the wall and the one on the set are the

same.

!

15

PREPARATION

WARNING

■ The image shown may be somewhat different from your set.

The SET must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing

injury or damaging the product. Use only an attached screw.

1-Screw

(provided as parts of the product)

Stand

Desk

►To prevent SET from falling over the SET should be securely attached to the floor/wall per installation

instructions. Tipping,shaking, or rocking the machine may cause injury.

ATTACHING THE TV TO A DESK (Only M2762DP)

16

PREPARATION

KENSINGTON SECURITY SYSTEM

- The product is equipped with a Kensington Security System connector on the back panel. Connect the

Kensington Security System cable as shown below.

- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided

with the Kensington Security System.

For further information, contact http://www.kensington.com, the internet homepage of the Kensington

company. Kensington sells security systems for expensive electronic equipment such as notebook

PCs and LCD projectors.

NOTE

- The Kensington Security System is an optional accessory.

NOTES

a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on.

This is normal, there is nothing wrong with product.

b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.

However, they have no adverse effect on the monitor’s performance.

c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.

Doing so may produce some temporary distortion effects on the screen.

17

EXTERNAL EQUIPMENT SETUP

ANTENNA CONNECTION

■ To prevent damage do not connect to the mains outlet until all connections are made between the devices.

■ For optimum picture quality, adjust antenna direction.

■ An antenna cable and converter are not supplied.

Multi-family Dwellings / Apartments

(Connect to wall antenna socket)

Wall

Antenna

Socket

Outdoor

Antenna

Single-family Dwellings / Houses

(Connect to wall jack for outdoor antenna)

RF Coaxial Wire (75 Ω)

■ In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.

■ If signal needs to be split for two sets, use an antenna signal splitter for connection.

EXTERNAL EQUIPMENT SETUP

Antenna

Signal

Amplifier

UHF

VHF

18

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

Connecting with a component cable

■ To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.

■ The image shown may be somewhat different from your set.

► HDMI Audio Supported format : Dolby Digital, PCM

► DTS Audio format is not supported.

Signal Component HDMI

480i / 576i YES No

480p / 576p YES YES

720p / 1080i YES YES

1080p

YES

(50 Hz / 60Hz only)

YES

(24 Hz / 30 Hz / 50Hz / 60Hz)

Connect the video outputs (Y, PB, PR) of the digital

set-top box to the COMPONENT IN VIDEO jacks on

the SET.

Connect the audio output of the digital set-top box

to the COMPONENT IN AUDIO jacks on the SET.

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top

box.)

Select COMPONENT input source using the INPUT

button on the remote control

1

2

3

4

1

2

19

EXTERNAL EQUIPMENT SETUP

Connecting a set-top box with a HDMI cable

Connect the digital set-top box to HDMI/DVI IN jack

on the SET

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

Select HDMI input source using the INPUT button on

the remote control.

1

2

3

NOTE

►Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed

HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable.

!

1

20

EXTERNAL EQUIPMENT SETUP

Connect the digital set-top box to HDMI/DVI IN jack on the SET.

Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the SET.

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

Select HDMI input source using the INPUT button on the remote control.

Connecting with an HDMI to DVI cable

1

2

3

4

1

2

Page is loading ...

LG LG M2262DP-PZ User manual

LG LG M2262DP-PZ User manual

Related papers

Other documents