Hotpoint TCEM 80C 6G (UK) User guide

Brand: Hotpoint

Model: TCEM 80C 6G (UK)

Category: Tumble dryers

Type: User guide

This manual is also suitable for

Instruction booklet

TUMBLE DRYER

Contents

Important information, 2-3

Installation, 4

Where to put your dryer

Ventilation

Water drain

Electrical connection

Before you start using your dryer

Dryer description, 5

The features

Control panel

Start and programmes, 6

Choosing a programme

Laundry, 7-8

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 9

General safety

Saving energy and respecting the environment

Maintenance and Care, 10

Switching off the electricity

Cleaning the filter after each cycle

Check the drum after each cycle

Empty the water container after each cycle

Cleaning the condenser unit

Cleaning the dryer

Troubleshooting, 11

Service, 12

Disposal

Hotpoint Guarantee, 15

Hotpoint After Sales Service, 16

English

TCAM 80C Aquarius

TCEM 80C Experience

TCYM 80C Style

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the

dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.

! Read these instructions carefully; the following pages contain important information on installation and suggestions

on how the appliance works.

This symbol reminds you to read this booklet.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Important Information

! You MUST clean the fluff filter after EVERY drying

cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

! You MUST empty the water container after EVERY

drying cycle.

Water Container...

Priming the Water Collection System

When your dryer is new, the water container will not collect water until the system is primed... this will take 1 or 2

drying cycles. Once primed it will collect water during every drying cycle.

STEP 1.

Open the door of your

dryer.

STEP 2.

Remove the filter.

STEP 3.

Open the filter and clean

any fluff deposits from

the filter mesh.

STEP 4.

Refit the filter - NEVER

run the dryer without the

filter in position.

For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 1.

Pull the water container

towards you and remove

it fully from the dryer.

STEP 2.

Remove either the small or

large cap and empty the

water from the container.

! Failure to empty the water container will result in:

- The machine will stop heating (so the load may still be wet at the end of the drying cycle).

- The ‘Empty Water’ light will tell you that the water container is full.

STEP 3.

Refit the water container,

ensuring that it is pushed

fully back into position.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Important Information

Condenser Unit...

! You MUST clean the fluff from the condenser EVERY

month.

! Failure to clean the condenser could cause premature

failure of your dryer.

●

Check that:

- The positioning arrows are pointing upwards.

- The 3 clips are re-secured back into their ‘lock’ position.

STEP 3.

Flush the condenser, from

the rear with water, to

remove any fluff deposits.

STEP 4.

Refit the condenser unit

- ensure that the unit is

pushed in fully, all 3 clips

are re-secured and the

positiong arrows on the

front of the condenser are

pointing upwards.

Rotate 3 clips

STEP 1.

Open the condenser cover

- hold the handle and

pull towards you.

STEP 2.

Remove the condenser by

rotating the 3 clips then

pulling the condenser

towards you.

(There may be some water

in the tubes, this is normal).

Installation

Moulded plug

! The plug must not be used

without the fuse cover in place.

If a replacement fuse

holder/cover is required, it must

be of the same colour coding or

wording as shown on the base of

the plug.

Replacements are available from

authorised dealers.

Changing the plug

The wires in the power cord are coloured in

accordance with the following:

! If the plug being replaced is a non-rewirable type,

then the cut-off plug must be disposed of safely. DO

NOT leave it where it can be inserted into a socket and

create a shock hazard.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see Service).

New or longer power cords are supplied at an extra

charge by authorised dealers.

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a

qualified electrician.

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects

on or above the machine and

a 15mm space between the

sides and lateral furnishings

or walls.

This is to ensure proper air circulation.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation could be experienced.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. If the dryer is stacked onto or

installed next to a washing machine it can share the same

drain. The height of the drain must be less than 3' (1m)

from the bottom of the dryer.

Remove hose from position shown

(see diagram).

Fit a suitable length of hose to the

new location shown (see diagram).

! Make sure that the hose is not squashed or kinked when

the dryer is in its final location.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

Ensure your hands are dry.

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating label

(see Dryer Description).

●

Power voltage must be within the values indicated on

the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the socket.

! Do not use extension cords.

! The dryer must not be installed outdoors, even if the space is

sheltered. It can be very dangerous if it is exposed to rain or

storms.

! Once installed, the dryers electrical wire and plug must be

within easy reach.

! The power cord must not be bent or squashed.

! The power cord supplied is fitted with a BS1363 plug and a 13

amp BS1362 fuse. If you need to replace the fuse, use only

those rated at 13 amp (13A) and ASTA approved to BS1362.

Green and Yellow

(Earth) wire to terminal

marked ‘E’, symbol ,

or coloured green and

yellow.

13A ASTA approved

fuse to BS1362.

Brown (Live) wire to

terminal marked ‘L’ or

coloured red.

Blue (Neutral) wire to

terminal marked ‘N’ or

coloured black.

Cord clamp

Minimum gap 10mm

Minimum gaps

15mm

Remove hose from

here...

...fit new hose here.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Dryer Description

Control panel

TIMER

Knob

START

Button

Indicator

Empty Water

Light

The Empty Water indicator light signals that the water

container is full and must be emptied. The light will

take a few seconds to go out after replacing the

empty water container, the dryer must be running for

this to happen.

Note: If the water container fills the indicator lights,

the heat is turned off and your laundry will not dry.

The TIMER knob sets a drying time.

Rotate it clockwise, never counter-clockwise, until

the indicator is pointing to the drying time you want to

select (see Start and Programmes).

The START button begins drying a selected

programme (see Start and Programmes).

The HEAT button selects drying temperature (see

Start and Programmes).

OUT: LOW heat

IN: HIGH heat

HEAT

Button

The features

Water container

Filter

Condenser cover

Rating plate

Model & Serial numbers

Condenser cover handle

(Pull to open)

Air intake grille

Start and Programmes

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door make sure the filter is clean and

in place and the water container is empty and in

place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. Choose the drying time by checking the

Drying Guide table for the type of fabric you are

drying (see Laundry).

- Set the temperature with the HEAT button.

- Select a drying time by rotating the TIMER knob

clockwise*.

6. Press the START button to begin.

During the drying programme, you can check on

your laundry and take out items that are dry

while others continue drying. When you close

the door again, press the START button in order

to resume drying.

7. About 10 minutes before the programme is

completed, it enters the final COOL TUMBLE

phase (fabrics are cooled), which should always

be allowed to complete.

8. Open the door, take the laundry out, clean the

filter and replace it. Empty the water container

and replace it (see Maintenance).

9. Unplug the dryer.

Note: The COOL TUMBLE programme can be used to refresh fibres of clothing.

- Set the TIMER with the cool tumble symbol inline with the indicator at Step 5 above* if you need this feature.

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Laundry

Sorting your laundry

●

Check symbols on clothing labels to make sure

that the articles can be tumble dried.

●

Sort laundry by fabric type.

●

Empty pockets and check buttons.

●

Close zippers and hooks and tie loose belts and

strings.

●

Wring out each item in order to eliminate as much

excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity.

These numbers refer to dry weight:

Natural fibres: 8kg max (18lb)

Synthetic fibres: 3kg max (6.6lb)

! DO NOT overload the dryer as this could result in

reduced drying performance.

Typical weights

Note: 1kg = 1000g (1lb = 16oz)

Clothes

Blouse Cotton 150g (5oz)

Other 100g (3oz)

Dress Cotton 500g (1lb 2oz)

Other 350g (12oz)

Jeans 700g (1lb 6oz)

10 nappies 1000g (2lb 3oz)

Shirt Cotton 300g (10oz)

Other 200g (7oz)

T-Shirt 125g (4oz)

Household Items

Duvet cover Cotton 1500g (3lb 5oz)

(Double) Other 1000g (2lb 3oz)

Large Tablecloth 700g (1lb 6oz)

Small Tablecloth 250g (9oz)

Tea Towel 100g (3oz)

Bath Towel 700g (1lb 6oz)

Hand Towel 350g (12oz)

Double Sheet 500g (1lb 2oz)

Single Sheet 350g (12oz)

At the end of a drying cycle, cottons could still be

damp if you grouped cottons and synthetics together.

If this happens simply give them an additional short

period of drying.

●

Note: The last 10 minutes of any time set is the

Cool Tumble, so allow for this when setting the time,

as this period will not dry your laundry.

Wash Care Labels

Look at the labels on your garments, especially when

tumble drying for the first time. The following symbols

are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

Items not suitable for tumble drying

●

Articles that containing rubber or rubber-like

materials or plastic film (pillows, cushions, or PVC

rainwear), any other flammable articles or objects

that contain flammable substances (towels soiled

with hair spray).

●

Glass fibres (certain types of draperies)

●

Items which have been dry cleaned

●

Items with the ITCL Code (see Special

clothing items). These can be cleaned with special

at-home dry cleaning products. Follow instructions

carefully.

●

Large bulky items (quilts, sleeping bags, pillows,

cushions, large bedspreads etc). These expand

when drying and would prevent airflow through

the dryer.

Laundry

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan,

Courtelle, Orion, Dralon) must be dried with special

care on LOW heat setting. Avoid drying for a long

period of time.

Pleated or creased garments: read the manufacturer’s

drying instructions on the garment.

Starched articles: do not dry these with non-starched

items. Make sure that as much of the starch solution is

removed from the load as possible before placing it in

the dryer. Do not over-dry: the starch will become

powdery and leave your clothing limp, which defeats

the purpose of starch.

Drying times

The table (see below) presents APPROXIMATE drying

times in Minutes. Weights refer to dry garments.

Times are approximate and can vary depending

upon:

●

Amount of water retained in clothes after spin

cycle: towels and delicates retain a lot of water.

●

Fabrics: items that are the same type of fabric but

different textures and thicknesses may not have

the same drying time.

●

Quantity of laundry: single items or small loads

may take longer to dry.

●

Dryness: If you are going to iron some of your

clothes, they can be taken out while still a bit

damp. Others can be left longer if you need them

to be completely dry.

●

Heat setting.

●

Room temperature: if the room where the dryer is

located is cold, it will take longer for the dryer to

dry your clothes.

●

Bulk: some bulky items can be tumble dried with

care. We suggest that you remove these items

several times, shake them out, and return them to

the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which

keeps them soft and fluffy.

Cottons

High/Full

Heat

Synthetics

Gentle/Low

Heat

Acrylics

Gentle/Low

Heat

Drying times 800-1000 rpm in washing machine.

Drying times on reduced spin in washing machine.

1 kg

2 kg

4 kg

3 kg

1 kg

2 kg

1 kg

2 kg

3 kg

5 kg

6 kg

7 kg

30 - 40

40 - 55

70 - 80

55 - 70

80 - 90

95 - 120

120 - 140

40 - 50

40 - 60 55 - 75

50 - 70

70 - 90

8 kg

130 - 150

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Warnings and Suggestions

! The appliance has been designed and built according

to international safety standards.

These warnings are given for safety reasons and must

be followed carefully.

General safety

●

This tumble dryer is not intended for use by

persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

●

This tumble dryer has been designed for home,

and not professional use.

●

Do not touch the appliance while barefoot or with

wet hands or feet.

●

Unplug the machine by pulling on the plug, not

the cord.

●

Children must not be in proximity of the dryer

when in use. After using the dryer, turn it off and

unplug it. Keep the door closed to make sure that

children do not use it as a toy.

●

Children should be supervised to ensure that they

do not play with the dryer.

●

The appliance must be installed correctly and

have proper ventilation. The air intake at the front

of the dryer should never be obstructed (see

Installation).

●

Never use the dryer on carpeting where the pile

height would prevent air from entering the dryer

from the base.

●

Check to see if the dryer is empty before loading it.

●

The back of the dryer could become very

hot. Never touch it while in use.

●

Do not use the dryer unless the filter, water

container and condenser are securely in place

(see Maintenance).

●

Do not overload the dryer (see Laundry for

maximum loads).

●

Do not load items that are dripping wet.

●

Carefully check all instructions on clothing labels

(see Laundry).

●

Do not tumble dry large, very bulky items.

●

Do not tumble dry acrylic fibres at high temperatures.

●

Complete each programme with its Cool Tumble Phase.

●

Do not turn off the dryer when there are still warm

items inside.

●

Clean the filter after each use (see Maintenance).

●

Empty the water container after each use (see

Maintenance).

●

Clean the condenser unit at regular intervals

(see Maintenance).

●

Do not allow lint to collect around the dryer.

●

Never climb on top of the dryer. It could result in damage.

●

Always follow electrical standards and requirements

(see Installation).

●

Always buy original spare parts and accessories

(see Service).

To minimise the risk of fire in your tumble dryer, the

following should be observed:

●

Tumble dry items only if they have been washed with

detergent and water, rinsed and been through the spin

cycle. It is a fire hazard to dry items that HAVE NOT

been washed with water.

●

Do not dry garments that have been treated with

chemical products.

●

Do not tumble dry items that have been spotted or

soaked with vegetable or cooking oils, this constitutes a

fire hazard. Oil-affected items can ignite spontaneously,

especially when exposed to heat sources such as a tumble

dryer. The items become warm, causing an oxidisation

reaction with the oil, Oxidisation creates heat. If the heat

cannot escape, items can become hot enough to catch

fire. Piling, stacking or storing oil-effected items can prevent

heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics containing vegetable or

cooking oil or those that have been contaminated with

hair care products be placed in a tumble dryer they should

first be washed with extra detergent - this will reduce, but

not eliminate the hazard. The cool tumble phase should

be used to reduce the temperature of the items. They

should not be removed from the dryer and piled or

stacked while hot.

●

Do not tumble dry items that have previously been

cleaned in or washed in, soaked in or soiled with

petrol/gasoline, dry cleaning solvents or other flammable

or explosive substances. Highly flammable substances

commonly used in domestic environments including

cooking oil, acetone, denatured alcohol, kerosene, spot

removers, turpentine, waxes and wax removers. Ensure

these items have been washed in hot water with an extra

amount of detergent before being dried in the tumble dryer.

●

Do not tumble dry items containing foam rubber (also

known as latex foam), or similarly textured rubber like

materials. Foam rubber materials can, when heated,

produce fire by spontaneous combustion.

●

Fabric softener or similar products should not be used in

a tumble dryer to eliminate the effects of static electricity

unless the practice is specifically recommended by the

manufacturer of the fabric softener product.

●

Do not tumble dry undergarments that contain metal

reinforcements eg. bras with metal reinforcing wires.

Damage to the tumble dryer can result if the metal

reinforcements come loose during drying.

●

Do not tumble dry rubber, plastic articles such as shower

caps or babies waterproof covers, polythene or paper.

●

Do not tumble dry rubber backed articles, clothes fitted

with foam rubber pads, pillows, galoshes and rubber

coated tennis shoes.

●

Remove all objects from pockets, especially lighters

(risk of explosion).

! WARNING: Never stop the dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

Saving energy and respecting the environment

●

Wring out items to eliminate excess water before

tumble drying (if you use a washing machine first,

select a high spin cycle). Doing this will save time

and energy during drying.

●

Always dry full loads - you save energy: single

items or small loads take longer to dry.

●

Clean the filter after each use to contain energy

consumption costs (see Maintenance).

Maintenance and Care

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless

steel drum, this may be caused by a combination of

water and, or cleaning agents such as fabric conditioner

from the wash. This coloured film will not affect the

dryer performance.

Cleaning the condenser unit

Periodically (every month) remove the condenser unit

and clean any build up of fluff from between the plates

by rinsing it under the tap with cold water.

This should be done with cold water from the rear of

the condenser.

Removing the condenser:

1. Unplug the dryer and open the door.

2. Pull open the condenser cover (see diagram).

Release the three catches by turning 90˚ counter-

clockwise then pull on the grip and remove from

the dryer.

3. Clean the surface of the seals and replace, making

sure that the catches have been secured.

Cleaning the dryer

●

External parts in metal or plastic and rubber parts

can be cleaned with a damp cloth.

●

Periodically (every 6 months) vacuum the front air

intake grille, to remove any build up of fluff, lint or

dust. Also to remove accumulation of fluff from the

front of the condenser and filter areas, clean

occasionally with a vacuum cleaner.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which

do not need lubrication.

! Have your dryer checked regularly by authorised

technicians to ensure electrical and mechanical safety

(see Service).

Switching off the electricity

! Unplug your dryer when not using it, when cleaning

it and during all maintenance operations.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying.

When finished drying, clean the filter by rinsing it

under running water or with your vacuum cleaner.

Should the filter become clogged up, the airflow inside

the dryer will be seriously compromised: drying times

lengthen and you will consume more energy. It may

also damage your dryer.

The filter is found in front of the dryer trim (see diagram).

Removing the filter:

1. Pull the plastic grip of the filter upwards (see diagram).

2. Open the filter and clean the lint from

the inside.

3. Replace it correctly. Ensure the filter

is fully located flush into the tumble

dryer trim.

4. Remove any lint that has built up on the inside of the

door and around the door seal.

! Do not use the dryer without replacing the filter.

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Empty the water container after each

cycle

Pull the container out of the dryer and remove either

the small or large cap and empty it into a sink or other

suitable drain. Refit the cap and replace the container

securely.

! Always check and empty the container before you

start a new drying programme.

Water container

Condenser cover

Catches

Air intake

Filter

Tap

Rear

Front

Condenser unit

Important

Information

Installation Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care Service

Troubleshooting

Problem:

The tumble dryer won’t start.

Its taking a long time to dry.

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The TIMER knob has not been set properly (see Start and Programmes).

●

The START button has not been pressed (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The water container needs emptying? The empty water light is on? (see

Maintenance).

●

The condenser needs cleaning? (see Maintenance).

●

The temperature setting is not ideal for the type of fabric you are drying

(see Start and Programmes, and see Laundry).

●

The correct drying time has not been selected for the load (see Laundry).

●

The air intake grille is obstructed (see Installation, and see

Maintenance).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

Service

Spare Parts

This dryer is a complex machine. Repairing it yourself

or having a non-authorised person try to repair it could

cause harm to one or more persons, could damage

the machine and could invalidate the spare parts

warranty.

Call an authorised technician if you experience problems

while using the machine.

Before calling the Service Centre:

●

Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

●

If not, turn off the dryer and call the Service Centre

closest to you.

What to tell the Service Centre:

●

name, address and post code.

●

telephone number.

●

the type of problem.

●

the date of purchase.

●

the appliance model (Mod.).

●

the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials

they contain and reduce the impact on human health

and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that

when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

As part of our continued commitment to helping

the environment, we reserve the right to use

quality recycled components to keep down customer

costs and minimise material wastage.

●

Disposing of the packaging material: follow local

regulations, so the packaging can be recycled.

●

To minimise risk of injury to children, remove the

door and plug - then cut off mains cable, flush

with the appliance. Dispose of these parts separately

to ensure that the appliance can no longer be

plugged into a mains socket.

Recycling and Disposal Information

This appliance conforms to the following EC Directives:

- 2006/95/EC (Low Voltage Equipment)

- 89/336/EEC, 92/31/EEC and 93/68/EEC (Electromagnetic Compatibility)

Guarantee

12 months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of

breakdown repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be

defective because of either workmanship or materials, we will, at our discretion, either

repair or replace the appliance at no cost to you.

The guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

- The appliance is only used on the electricity or gas supply printed on the rating plate.

- The appliance has been used for normal domestic purposes only.

- The appliance has not been altered, serviced, maintained, dismantled or otherwise

interfered with by any person not authorised by us.

- Any repair work must be undertaken by us or our appointed agent.

- Any parts removed during repair work or any appliance that is replaced become our

property.

- The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

- Damage resulting from transportation, improper use, neglect or interference or as a

result of improper installation.

- Replacement of any consumable item or accessory. These include but are not limited to:

plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

- Replacement of any removable parts made of glass or plastic.

THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN

COMMERCIAL OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is

conditional on you registering your appliance with us and the parts being fitted by one

of our authorised engineers. There will be a charge for our engineer’s time.

To activate the extra parts warranty on your appliance, simply call our free phone registration line on

0800 519 2110 (Republic of Ireland 1800 844 347)

Extended Guarantees

We offer a selection of protection plans that enable you to fully cover yourself against the

expense of repair bills for the life of your policy. To find the ideal plan for you please call our

advice line on

08448 226 226 (Republic of Ireland 01 230 0233)

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if

you experience any technical difficulties within the first 90 days of ownership. Simply call our

Hotpoint Service Hotline on

08448 224 224 (Republic of Ireland 0818 313 413)

for telephone

assistance, or, where necessary, to arrange for an engineer to call.

195101074.00 W

04/2012 - LION fpg . Four Ashes, Wolverhampton

Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB

Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its

working life than us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in the country offering you access to 400 skilled

telephone advisors and 1100 fully qualified engineers on call to ensure you receive

fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number

Serial number

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that

protect and hygienically clean your appliance to keep it looking good and functioning

efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your FREE 5 year

parts guarantee you must register your appliance with us.

Free phone UK: 0800 519 2110

Republic of Ireland: 1800 844 347

www.hotpointservice.co.uk

Recycling and Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint

reserves the right to use quality, recycled components to keep down customer costs and

minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to

children, remove the door, plug, and cut the mains cable off flush with the appliance. Dispose

of these parts separately to ensure that the appliance can no longer be plugged into a mains

socket and the door cannot be locked shut.

Hotpoint TCEM 80C 6G (UK) User guide

Brand: Hotpoint

Model: TCEM 80C 6G (UK)

Category: Tumble dryers

Type: User guide

This manual is also suitable for

Download PDF

report

Hotpoint TCEM 80C 6G (UK) User guide

This manual is also suitable for

Hotpoint TCEM 80C 6G (UK) User guide

Related papers

Other documents