OWNER’S MANUAL
LPB11NM Rev 1.0 10/2018
HEAD
TV
1 2
Z-G
SNORE
FOOT
HEAD BOARD
HEAD BOARD
HEAD
TV
1 2
Z-G
SNORE
FOOT
×1
2
Take out all the accessories from the packaging and put them aside.
ACCESSORIES BOX:
×1
AC Power Cord
×6
Adjustable
Legs
×6
4
Remove the bed from the box
with a flipping motion, let the
bed stand on the 4 legs.
5
Flip the foot end of the bed
from the box and lay it on top
of the head end.
Setup the power foundation without the bed frame.
×1
Remote
Control
×1
Power Supply
×1
Slat/ Platform
Legs
Slat/ Platform
Legs
Sync Cord
TXL Only
×3
AAA
Batteries
1
Open the box lid.
HEAD BOARD
3
Install 4 legs.
HEAD BOARD
×4
Stabilizer
Brackets
×1
Socket Wrench
×1
Mattress Retainer Bar
×1
Accessories Box
×8
Screws
ST4.2×16
×8
Washers
×8
Bolts
M8*16
6
7
HEAD BOARD
DC Power Cord
Control Box
Install the remaining 2 legs on
the foot end of the bed.
Uncoil the DC power cord
(connected to the control box)
and put it to the side of the bed.
Make the bed completely flat.
8
one side after another.
Install the mattress retainer bar
2
1
Insert the batteries into
the remote control.
HEAD
TV
1 2
Z-G
SNORE
FOOT
HEAD BOARD
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
HEAD BOARD
9
Uncoil the AC power cord, connect
the DC power cord to the power
supply and then connect the
power supply to the AC
power source.
HEAD
TV
1 2
Z-G
SNORE
FOOT
Insert the batteries into
the remote control.
1
HEAD BOARD
DC Power Cord
2
Make the bed completely flat
with a flipping motion
.
3
Install the mattress retainer bar one side after another.
HEAD BOARD
DC Power Cord
2
1
HEAD BOARD
DC Power Cord
HEAD BOARD
4
Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply to the AC
power source.
Setup the power foundation with the bed frame and slat base.
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
Take the bed out of the box, put it on the slat base
, do not
install
any legs. Uncoil the DC power cord (connected to the control box)
pull the DC power cord towards the direction of the AC power source
through either the bottom or the side of the bed frame.
HEAD
TV
1 2
Z-G
SNORE
FOOT
HEAD
TV
1 2
Z-G
SNORE
FOOT
5
Lift the head and foot end of
the bed by remote control.
Install the four stabilizer
brackets as shown.
Parts List
INCLUDED WITH POWER FOUNDATION
HEAD BOARD
DONE!
Add Additional Leg Supports For Slat/Platform Bed Frames.
Leg
Configuration
Bed Height
Adjustable Range
Leg Configuration Table
7”—7.5” 11”—11.5” 15”—15.5” 18.5”—19”
Support leg may be needed on some slat/platform bed frames, refer to the
leg configuration table for height adjustment.
Slat/ Platform
Legs
(1)
AC Power Cord
(1)
Remote Control
(3)AAA Batteries
(1)
Sync Cord
(TXL Only)
Stabilizer
Brackets
(4)
(1)
Socket Wrench
Screws
ST4.2×16
M8*16 Bolts
Washers
(8)
Screws
ST4.2×16
(6)(8)M8*16 Bolts (8)Washers
9V
9V
(optional)
9V
Synchronizing Two Foundations
Electronics Quick Reference Guide
STEP 1Unplug foundations from the power source.
STEP 2Connect the male ends of the sync cord to the female sync plugs of the
control boxes (Refer to below illustration).
STEP 3Plug foundations back into the power source.
STEP 4Check to ensure all cords are securely attached.Either remote will
operate both foundations simultaneously.
Sync Plug
Sync Plug
Control Box 1 Control Box 2
Sync Cord
Control Box 1
HD Motor
LED APP SYN
FT Motor USB Power
HD Motor
LED APP SYN
FT Motor USB Power
USB
Charger
Power Supply
LED
Sync Cord
Head Motor Foot Motor
HD Motor
LED APP SYN
FT Motor USB Power
HEAD
TV
1 2
Z-G
SNORE
FOOT
Lifts and
Lowers Head
Lifts and
Lowers Foot
Under Bed
LED on/off
Home Position
Programmable
Positions
Zero G Preset
Position
Anti-Snore
Preset Position
TV Position
UNDERNEATH LED LIGHTING
ONE TOUCH BUTTON
ADJUST
This button lifts the head/foot section of
the foundation.
One touch ANTI-SNORE preset position.
SNORE
One touch TV preset position.
TV
One touch ZERO G preset position.
ZERO G adjusts your legs to a higher
level than your heart, helping to relieve
pressure of the lower back and promote
circulation.
Z-G
One touch programmable positions.
2
1
One touch underneath LED lighting
on/off.
This button lowers the head/foot section
of the foundation.
HEAD
TV
1 2
Z-G
SNORE
FOOT
One touch flat position.
DC
Power Cord
AC
Power Cord
WIRELESS RECEIVER
CB11B
Control Box
Remote Control
Pairing Remote
Setting Programmable Position
Adjust the head and foot to your desired position.
To adjust a saved position, repeat step 1 and 2 and the new position
will be saved.
Press and hold the LED on/off button first, then press and hold one
of the picture programmable buttons for 5 seconds until you hear
a beep sound. The position is then saved.
1 2
STEP 1
STEP 2
STEP 3
HEAD
TV
1 2
Z-G
SNORE
FOOT
Make sure the batteries are good. Replace
them when needed.
Unplug the power cord from the power source. If 9V backup batteries
were installed in the power supply, remove them.
Press and hold and simultaneously until the blue backlights
of the remote control are off.
STEP 1
STEP 2
STEP 3
STEP 4
Plug the power cord back into the power source. You will hear an activation
sound in 2 seconds, indicating the remote is paired to the power foundation.
1
2
2
1
a)Align the slot hole of the headboard bracket to the sleeve into
which the leg threads. DO NOT OVERTIGHTEN. Too much force
may damage the thread.
b)The headboard bracket has 2 adjustable slots to accommodate
any frame type. Use the bolts and Washers to secure the bracket.
Make sure the bolts are tight.
Headboard Bracket Installation Guide(Optional)
Headboard brackets are optional and not included. A 1/2” (13 mm)
socket and 1/2” (13 mm) wrench are required to complete the installation.
a)To put the T-Bracket and Headboard Bracket together, you will
need (2) M8×16 bolts and (2) nuts. Slip the bolts through the holes
from T-Bracket to Headboard Bracket with the head of bolt facing
outward. Use the 1/2” (13 mm) socket and 1/2” (13mm) wrench to
tighten the bolts.
You may now connect your headboard to the attachment plates using the remaining short bolts
and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2” (13mm)
socket and 1/2” (13mm) wrench to tighten the bolts.
(2) Headboard Brackets
(2) T-Brackets (8) M8*16 (4) Nuts (4) Washers
* Remote interface varies in between different Bedgear Power Foundation models. If you wish
to disconnect from the current paired Power Foundation, Enter the Settings Page and tap the
Disconnect button.
Bedgear Mobile APPOptional
GET INSTALL
REMOTE CONTROL
SNORE
TV
Z-G
2
1
1
2
8
3 5
4 6
7 9
1110 12
1
12
11
10
9
8
7
5
4
3
2
6
Enter the Settings Page
Head Lifting function
Head Lowering function
Foot Lifting function
Foot Lowering function
One touch flat Position
Anti-Snore Preset Position
TV Position
Zero G Preset Position
Programmable Position 1
Programmable Position 2
Under Bed Lighting
Customer Service Toll Free:1-844-696-6886
The Bedgear Mobile APP uses the latest technology to communicate with your Bedgear
Power Foundation. Make sure your mobile devices needs to have the pairing function for the
APP to work correctly.
Before you start. Switch on the pairing function on your mobile device. Make sure your
Bedgear Power Foundation is correctly connected and is power-on.
The
Bedgear
APP will automatically pair your
Bedgear
Power Foundation once you start
the APP and does not require additional settings.
www.bedgear.com
REMOTE CONTROL
REMOTE CONTROL
HEAD FOOT
REMOTE CONTROL
REMOTE CONTROL
1
STOP
2
REMOTE CONTROL
1 2
TV
Z-G
SNORE
REMOTE CONTROL
2
1
STOP
REMOTE CONTROL
SNORE
TV
Z-G
2
1
REMOTE CONTROL
1
STOP
2
TV
Z-G
SNORE
OWNER’S MANUAL
Four-button Remote Control
Three-button Remote Control
Five-button Remote Control
Eleven-button Remote Control
Eleven-button Remote Control
Ten-button Remote Control
Ten-button Remote Control
Thirteen-button Remote Control
Thank you for purchasing a Bedgear
Power Foundation.
* The effective connection range is ± 10m
8
7
6
5
4
3
2
1
List of Bedgear Products within
the connection range*
Tap the Refresh Button to refresh
the Bedgear Products List
Enter the Settings Page
Back to the Home Screen
9
Serial Number of the control box
Owner’s Manual Page
Troubleshooting
Disconnect from the paired
Bedgear Product
Rename your Bedgear Power
Foundation of your choice
Home Screen
Settings Page
9
SELECT DEVICE
BED
Refresh
3
1
2
SETTINGS
DISCONNECT
Serial Number
5
4
RENAME
OWNER’S MANUAL
6
7
TROUBLESHOOTING
8
Bedgear Bedgear
Bedgear
Bedgear APP Home Screen
Bedgear APP Remote Control
bedgear
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Bedgear 701115050 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Furniture of America IDF-4456E Installation guide
-
Rize Contemporary III Owner's manual
-
Natures Sleep GhostBed Adjustable Power Base User manual
-
Regal CB500REG Owner's manual
-
Noble House 296012 Operating instructions
-
Noble House 8276 Operating instructions
-
Leggett & Platt U-232 Owner's manual
-
Serta 500828319-7550 User guide
-
Richmat Smart Home User manual
-
DAWN HOUSE 89004774 User guide
