Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • inf[email protected] DocID: 460576_30.11.2020
Safety instructions
Intended use
This device is intended for lighting temporarily racks by means of LED technology.
Any other use or use under other operating conditions is considered to be improper
and may result in personal injury or property damage. No liability will be assumed
for damages resulting from improper use.
Extend the operating life of the device by regular breaks and by avoiding
frequent switching on and o. The device is not suitable for continuous
operation.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure
that children do not detach any small parts from the product. They could
swallow the pieces and choke! Never let children unattended use electri-
cal devices.
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never re-
move any covers. There are no user-serviceable parts inside. Do not use the device
when covers, safety equipment or optical components are missing or damaged.
Electric shock caused by short-circuit
Always use proper ready-made insulated two-wire mains cabling (power cord).
Do not modify the mains cable or the plug. Failure to do so could result in electric
shock/death or re. If in doubt, seek advice from a registered electrician.
Quick Start Guide
This quick start guide contains important information on the safe operation of the
device. Read and follow the safety advice and instructions given. Retain the manual for
future reference. If you pass the device on to others please include this manual.
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual current
circuit breaker. Failure to do so could result in damage to the device and possibly the
user. Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or re.
Where to use the product
Never use the product
• in direct sunlight
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
General handling
• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use
liquid cleaners such as benzene, thinners or ammable cleaning agents.
• For technological reasons, the light output of LEDs decreases over their lifetime. This
eect increases with higher operating temperature. You can extend the service life of
the illuminants by providing adequate ventilation and operating the LEDs with the
lowest possible brightness.
Features
• Multicolour rack light an even illumination of the rack
• Suitable for 19" racks (1 RU)
• 15 selectable macros with dierent hues
• Three selectable brightness levels
• Memory function
• Incl. power adapter
• Strain relief for the power adapter
Controls and connections
Technical specications
Light source: 30 × multicolour RGBW 4in1 LEDs
Colour temperature: 3200K, 5600K, 7200K
Light output: 150 lumen
Power supply: 12 V
EN
For the transport and protective packaging, environmentally friendly materi-
als have been chosen that can be supplied to normal recycling. Ensure that
plastic bags, packaging, etc. are properly disposed of. Do not just dispose of
these materials with your normal household waste, but make sure that they are
collected for recycling. Please follow the notes and markings on the packaging.
SRL Solid Rack Light
Material: metal
Colour: black
Dimensions (W × H × D): 485 mm × 44 mm × 60 mm
Weight: 0.9kg
ö
Dimmer/Switch: Button to turn the unit on and o and set the
brightness of the LEDs
#
POWER IN: Connection socket for the power adapter
$
Color: Button to set the colours of the LEDs
Operating
1. Turn the unit on and o
Keep the button [Dimmer/Switch] pressed until the unit switches on or o.
2. Brightness setting
Repeatedly press the button [Dimmer/Switch] to select one of the three brightness levels of the LEDs.
3. Macros setting
Repeatedly press the button [Colors] to select one of the 15 hues of the LEDs.
4. Memory function
All settings of brightness and macros are retained, even if the unit is disconnected from the mains.
ö
# $
This product is subject to the European Waste Electrical and Electronic Equip-
ment Directive (WEEE) in its currently valid version. Do not dispose of your old
device with your normal household waste. Dispose of this product through an
approved waste disposal rm or through your local waste facility. Comply with
the rules and regulations that apply in your country. If in doubt, consult your
local waste disposal facility.
/