AGFEO S0-Modul 110
The AGFEO S0-Modul 110 is a device that adds an internal S0 bus to the AS 140, AS 140 plus, AS 190 and the AS 190 plus. The connections for this internal S0 bus are already provided.
Possible use cases:
- Connecting an ISDN telephone to the internal S0 bus
- Connecting a fax machine to the internal S0 bus
- Connecting a PC to the internal S0 bus for data communication
Benefits:
- Provides an internal S0 bus for connecting ISDN devices
- Easy to install
- No additional wiring required
Features:
- Adds an internal S0 bus to the AS 140, AS 140 plus, AS 190 and the AS 190 plus
AGFEO S0-Modul 110
The AGFEO S0-Modul 110 is a device that adds an internal S0 bus to the AS 140, AS 140 plus, AS 190 and the AS 190 plus. The connections for this internal S0 bus are already provided.
Possible use cases:
- Connecting an ISDN telephone to the internal S0 bus
- Connecting a fax machine to the internal S0 bus
- Connecting a PC to the internal S0 bus for data communication
Benefits:
- Provides an internal S0 bus for connecting ISDN devices
- Easy to install
- No additional wiring required
Features:
- Adds an internal S0 bus to the AS 140, AS 140 plus, AS 190 and the AS 190 plus
S0 Module 110
Safety Instructions ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
Before opening the housing of the AS 140, AS 140 plus, AS
190, AS 190 plus, pull out the 230 V mains plug of the
telecommunications system from the socket.
The S0 module 110 may only be installed by a technician
qualified under DIN 57105/VDE.
Do not give these instructions to the end user!
Telekommunikation
Installation Instructions
S0 Module 110 ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
The module adds an internal S0 bus to the
AS 140, AS 140 plus, AS 190 and the AS
190 plus. The connections for this internal
S0 bus are already provided.
!
Opening the housing ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
Upper shell
S
D
D
Housing cover
- Remove the cover from the housing.
Reach behind the cover of the telecom-
munications system housing on the bot-
tom.
- Pull the edge of the cover down slightly so
that it snaps out.
- Remove the cover from the housing from
the front.
- Loosen the securing screw S. You need
this screw again for reassembly.
- Press the bottom shell together lightly on
the left and right (see drawing point ‘D’).
The housing springs open.
- Tip the top shell up to the left and release
the snap catches.
Removing the module from the packaging - Safety measures ¢¢¢¢¢¢¢¢¢¢¢¢¢¢
. You have the safety packaging of the
module in your other hand.
This discharges any static which may have
built up and protects the electrostatically
sensitive components of the AS 140
(plus), AS 190 (plus) and the module.
Before removing the module from the
ESD safety packaging and before inserting
the module in the AS 140 (plus) or AS
190 (plus), touch the metal shield of the
PC/printer socket of the telephone system
briefly with your finger.
2
AGFEO GmbH & Co. KG
Gaswerkstr. 8
D-33647 Bielefeld
Internet: http://www.agfeo.de
ID No. 524 522
Subject to modifications and errors.
Printed in Germany
0999
- Plug the S0 module 110 with the connec-
tor strip to the socket strip of the AS 140
(plus) or AS 190 (plus).
Installation of the module¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
- Fix the S0 module with screws MS1 and
MS2 using one spring washer each on the
circuit board.
MS1
MS2
S0 module 110
Socket strip
Connector strip
Closing the housing¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
- Position the hooks in the upper shell in re-
cesses of the lower shell.
- Tip the upper shell down to the right.
- With a slight pressure, the upper shell
snaps into the lower shell.
- Fix the upper shell to the lower shell with
the securing screw S.
- Hang the cover for the connecting panel
to the top of the housing first. The three
lugs grip behind the edge of the housing.
- Press the cover until it snaps into the bot-
tom of the housing.
Startup ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
- Switch on the telecommunications sys-
tem by plugging in the 230 V- mains
plug
Make sure that the housing is closed all round and all hooks
have snapped in.
It should not be possible to open the upper shell by lifting it.
There may be a risk of touching fatal voltages through open-
ings between the upper and lower shells!
!
Circuit board AS 140 (plus),
AS 190 (plus)
-
1
-
2
AGFEO S0-Modul 110 Installation guide
- Type
- Installation guide
- This manual is also suitable for
AGFEO S0-Modul 110
The AGFEO S0-Modul 110 is a device that adds an internal S0 bus to the AS 140, AS 140 plus, AS 190 and the AS 190 plus. The connections for this internal S0 bus are already provided.
Possible use cases:
- Connecting an ISDN telephone to the internal S0 bus
- Connecting a fax machine to the internal S0 bus
- Connecting a PC to the internal S0 bus for data communication
Benefits:
- Provides an internal S0 bus for connecting ISDN devices
- Easy to install
- No additional wiring required
Features:
- Adds an internal S0 bus to the AS 140, AS 140 plus, AS 190 and the AS 190 plus
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Intermec EasyCoder PF4i User manual
-
Intermec EasyCoder PX6i User manual
-
HP sx2000 User manual
-
Invacare Twister User manual
-
Unical TRIOPREX N Installation guide
-
AEG KSE792220B User manual
-
-
-
-
