Tripp Lite PDUMV30HVNET Owner's manual

1

Owner’s Manual

Monitored Rack PDU

Switched Rack PDU

Zero U (Vertical) Format

AGPD7897 (208/230V 16 Amp Models) • AGPD7898 (208V 24 Amp Models)

AG00CA (200-240V 32A models)

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Important Safety Instructions 2

Monitored Rack PDU Features 2

Switched Rack PDU Features 3

Installation 3

Features 8

Configuration and Operation 10

Warranty and Warranty Registration 11

Español 13

Français 25

Русский 37

Warranty

Registration

Register online today for a

chance to win a FREE Tripp Lite

product! www.tripplite.com/warranty

13-11-194-933093.indb 1 12/5/2013 5:21:52 PM

2

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed

during the installation, operation, and storage of this product. Failure to

heed these instructions and warnings will void the product warranty.

Important Safety Instructions

Monitored Rack PDU Features

• ThePDUprovidesconvenientmultipleoutlets,butitDOESNOTprovidesurgeorlinenoise

protection for connected equipment.

• ThePDUisdesignedforindooruseonlyinacontrolledenvironmentisolatedfromexcess

moisture,temperatureextremes,conductivecontaminants,dustordirectsunlight.

• DonotconnectthePDUtoanungroundedoutletortoextensioncordsoradaptersthat

eliminate the connection to ground.

• ThepowerrequirementforeachitemofequipmentconnectedtothePDUmustnotexceed

the individual outlet’s load rating.

• ThetotalpowerrequirementforequipmentconnectedtothePDUmustnotexceedthe

maximumloadratingforthePDU.

• DonotdrillintoorattempttoopenanypartofthePDUhousing.Therearenouser-

serviceablepartsinside.

• DonotattempttomodifythePDU,includingitsinputplugsandpowercables.

• DonotattempttousethePDUifanypartofitisdamaged.

• DonotattempttomountthePDUtoaninsecureorunstablesurface.

• Neverattempttoinstallelectricalequipmentduringathunderstorm.

• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcan

reasonablybeexpectedtocausethefailureofthelifesupportequipmentortosignificantly

affectitssafetyoreffectivenessisnotrecommended.Donotusethisequipmentinthe

presenceofaflammableanestheticmixturewithair,oxygenornitrousoxide.

•InstallinaccordancewithNationalElectricalCodes.Besuretousetheproperovercurrent

protectionfortheinstallation,inaccordancewiththeplugrating.

•Theelectricalsocketssupplyingpowertotheequipmentshallbeinstallednearthe

equipmentandbeeasilyaccessible.

•Networkinterfaceenablesremotepowermonitoringandeventnotification

•Digitalampmeterforon-siteloadmonitoring

•CentralizedmanagementofhundredsofPDUsandenvironmentalsensorswithTrippLite’s

freePowerAlertNetworkManagementSystem

•OptionalENVIROSENSEaccessoryallowsmonitoringofnetworkambienttemperature,

humidity and up to three dry contacts

•Toollessbutton-mountinstallationinTrippLiteSmartRack™andmanythird-partyenclosures

13-11-194-933093.indb 2 12/5/2013 5:21:53 PM

3

Switched Rack PDU Features

•Networkinterfaceenablesremotepowermonitoringandindividualoutletcontrol

•Individuallycontrollableoutletsallowremoterebootingoflocked-upnetworkdevices

•Digitalampmeterforon-siteloadmonitoring

•CentralizedmanagementofhundredsofPDUsandenvironmentalsensorswithTrippLite’s

freePowerAlertNetworkManagementSystem

•OptionalENVIROSENSEaccessoryallowsmonitoringofnetworkambienttemperature,

humidity and up to three dry contacts

•Toollessbutton-mountinstallationinTrippLiteSmartRackandmanythird-partyenclosures

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of configuration, the user must

determine the fitness of hardware and procedures before mounting. The PDU and included hardware are

designed for common rack and rack enclosure types and may not be appropriate for all applications. Exact

mounting configurations may vary. Screws for attaching the mounting brackets and cord retention shelf to the

PDU are included. Use only the screws supplied by the manufacturer, or their exact equivalent (#6-32, ¼"

flat head).

IfinstallingthePDUinarackthathasbutton-mountslots,youonlyneedtoperformstep

1-1

.

Ifyourrackenclosuredoesnothavebutton-mountslots,proceedtostep

1-2

.

Installation

1-1

ToinstallthePDUinarackequipped

withbutton-mountslots,insertthe

mountingbuttonsontherearofthe

PDUintothebutton-mountslotson

therackandslidethePDUdownuntil

themountingbuttonsengagethe

narrowsectionoftheofthebutton-

mount slots.

Note: To install the PDU with its outlets

facing the rear of the rack, use the

included PDUMVROTATEBRKT accessory.

This V-shaped bracket provides a mounting

button on one leg of the V and a button-

mount slot on the other, effectively

repositioning the mounting buttons. See

Features section for image.

1-2

Attachthemountingbracketstothe

PDU.

1-3

(Optional)Attachthecordretention

bracket(s)tothePDU.

1-4

AttachthePDUtoaverticalrailin

yourrackorrackenclosure.(Usethe

mounting hardware that came with

yourrackorrackenclosuretoattach

themountingbracketstotherail.)

1-2

1-1

1-3 1-4

13-11-194-933093.indb 3 12/5/2013 5:21:54 PM

4

Connecting the PDU

2-1

(ModelswithIECpowerinletor3-pole

IEC309plugonly.)Selectmodelshave

adetachablepowercord.Attachthe

includedpowercordtothePDUby

insertingtheIECconnector

A

of the

powercordintotheIECpowerinlet

B

locatedneartheendofthePDU.Use

theincludedbracket

C

to secure the

power cord connection.

Note: Optionally, a user-supplied power cord

can be attached to the PDU by connecting it

to the IEC inlet. Do not attempt to attach a

user-supplied power cord unless it is certified

to be compatible with the input power source

that will be used by the PDU.

2-2

(Optional-modelswithinputplug

adapteronly.)Selectmodelsincludean

input plug adapter that converts the

twist-lockinputplugtoastraight-blade

input plug. Attach the input plug adapter

A

to the input plug

B

if you wish to

plugthePDUintoacompatiblestraight-

bladeoutlet.

2-3

Connecttheinputplugtoacompatible

ACpoweroutlet.IfthePDUdoesnot

haveacircuitbreaker,itshouldbe

providedwithabranch-ratedover-

current protection device that matches

theratedamperageofthePDU.

Note: The AC power source should not share

a circuit with a heavy electrical load.

2-4

(Option1-selectmodelsonly.)Ifyou

attachedthecordretentionbracket(s),

tie each equipment power cord to the

retentionbracket.Attacheachcordto

theretentionshelfbyloopingthecord

and securing it with one of the included

cableties

A

.Makesurethateachcord

canbeunpluggedfromthePDUwithout

removingthecabletie.

  (Option2)UsetheincludedC14and

C20 plastic sleeves to secure plugs to

receptacles. Attach the sleeve to the

plug,makingsurethatthepulltabs

B

remain outside the plug and that the fit

issecure.Tounplugequipmentproperly,

usethepulltabstoremovetheplug

and sleeve from the receptacle.

Installation continued

2-1

2-2

2-3

A

C

B

A

B

2-4

B

A

13-11-194-933093.indb 4 12/5/2013 5:21:56 PM

5

Installation continued

2-5

Connect your equipment's input plugs

A

to the outlets

B

ofthePDU.TheLED

C

near each outlet (Switched Models

Only) illuminates when the outlet is

readytodistributeliveACpower.The

digital load meter

D

displays the total

connected equipment load in amps.

(Selectmodelsprovideadditionalload

data.SeetheFeatures section for

moreinformation.)

Note: In order to minimize interference among

connected devices, connect each device to

the nearest PDU outlet and coil excess power

cord length.

Networking the PDU

Note: The MAC address of the PDU (a 12-digit string in this format: 000667xxxxxx) is printed on a label

attached to the PDU enclosure.

Ifyournetwork'sDHCPserverwillassignadynamicIPaddresstothePDUautomatically,goto

Step

3-1

.IfyouwillassignastaticIPaddresstothePDUmanually,gotoStep

4-1

.Ifyouare

uncertainwhichmethodtouse,contactyournetworkadministratorforassistancebefore

continuing the installation process.

Dynamic IP Address Assignment

3-1

Connect PDU to Network: While the

PDUispowered,connectastandard

EthernetpatchcabletotheRJ-45

Ethernet port

A

onthePDU.

Note: This port is not compatible with PoE

(Power over Ethernet) applications. The PDU

will attempt to obtain an IP address via DHCP.

This may take as long as several minutes,

depending on your network environment.

3-2

Discover IP Address:ContactyournetworkadministratortodeterminewhichdynamicIP

addresshasbeenassignedtothePDUbytheDHCPserver.ThePDUcanbeidentifiedon

theDHCPserverbyreferringtoitsMACaddress.(TheMACaddressisa12-digitstringin

thisformat:000667xxxxxx.RefertotheMACaddresslabelattachedtothePDU.)Youmay

wishtorequestalong-termleaseperiodfortheIPaddress,dependingonyourapplication.

AfteryouhavediscoveredtheIPaddress,skipSteps

4-1

through

4-6

and proceed

directlytoStep

5-1

.

Static IP Address Assignment

4-1

Determine IP Information:BeforeassigningastaticIPaddress,you'llneedtoknowthe

IPaddress,gatewayaddressandsubnetmask.Ifyoudonothavethisinformation,contact

yournetworkadministratorforassistance.

(Will vary by model.)

2-5

A

D

24 23 22 21

20

19 18 17 16 15

14

13

ENVIROSENSEENVIROSENSE

CONFIGCONFIGACCYACCY

RESETRESET

LINKLINK

STATUSSTATUS

12

11 10 9 8 7

6 5 4 3

2 1

INLET

3-1

A

B

C

13-11-194-933093.indb 5 12/5/2013 5:21:58 PM

6

Bitspersecond: 9600

Databits: 8

Parity: None

Stopbits: 1

Flowcontrol: None

Installation continued

4-2

Configure Terminal Emulation Program:OpenaVT100-compatibleterminalemulation

program(suchastheHyperTerminalprogrambundledwithMicrosoft

®

Windows

®

)ona

computerwithanavailableDB9serialport.(Anotebookcomputermaybethemost

convenientchoice.)SettheterminalemulationprogramtousetheCOMportthat

correspondstothecomputer’sDB9serialport.Specifytheparametersrequiredto

communicatewiththePDUterminalinterface:

  Iftheterminalemulationprogramsupportsmultipleemulationmodes,youmayalsoneed

tospecifyVT100emulation.

4-3

Connect PDU to Computer: Usethe

RJ-45toDB9serialcable(partnumber

73-1243)includedwiththePDUto

connectthePDUtothecomputer.The

RJ-45connector

A

at one end of the

cableattachestotheCONFIGport

B

onthePDU.TheDB9connector

C

at

theotherendofthecableconnectsto

the computer's serial port

D

.

4-4

Connect PDU to Network: While the

PDUispowered,connectastandard

EthernetpatchcabletotheRJ-45

Ethernet port

A

onthePDU.

Note: This port is not compatible with PoE

(Power over Ethernet) applications.

4-5

Configure PDU in Terminal Mode:

Afterabriefpause,aninitializationpage

should appear in the terminal emulation

program.Pressanykeyonthekeyboard

within10secondstochangethePDU

settings.(Ifthe10-secondperiodhas

elapsed,youcanrebootthePDUby

pressingtheSNMPresetswitch.)

  Followthesequenceofresponsesbelow

inordertoassignanIPaddresstothe

PDU.Thedefaultterminalmoderoot

password is TrippLite.SampleIPsettings

areshown-supplyyourownIP

information when you configure your

PDU.

4-3

4-5

B

24 23 22 21

20

19 18 17 16 15

14

13

ENVIROSENSEENVIROSENSE

CONFIGCONFIGACCYACCY

RESETRESET

LINKLINK

STATUSSTATUS

12

11 10 9 8 7

6 5 4 3

2 1

INLET

4-4

A

C

D

13-11-194-933093.indb 6 12/5/2013 5:22:00 PM

7

Press A to Accept the settings, or M to Modify? M

Enter the root password: *********

Reset configuration to default values (Y/N)? N

For each of the following questions, you can press <Return> to select the value shown in

braces, or you can enter a new value.

NETWORK INTERFACE PARAMETERS:

Should this target obtain IP settings from the network?[N] N

Static IP address [192.168.1.19]? 192.168.0.123

Static IP address is 192.168.0.123

Subnet Mask IP address [255.255.0.0]? 255.255.255.0

Subnet Mask IP address is 255.255.255.0

Gateway address IP address [192.168.1.1]? 192.168.0.1

Gateway address IP address is 192.168.0.1

Youcanalsochangetherootpassword,real-timeclockandothersettings.(TrippLite

recommends against changing the default settings unless you are an advanced user with a

specificpurpose.)Afteryouhavefinishedenteringsettings,thePDUwillsavechangestomemory

andreboot(thismaytakeseveralminutes).AfterthePDUreboots,theinitializationpageshould

displaythenewstaticIPsettings.

4-6

Remove Serial Cable: RemovetheserialcablefromthePDUandproceedtoStep

5-1

.

Testing Network Connection

5-1

Access PDU with Web Browser:

AfteranIPaddresshasbeenassigned

tothePDU,attempttoaccessitwitha

Webbrowserthatsupportsframes,

formsandJava™.OpenaWebbrowser

onacomputerconnectedtotheLAN

andentertheIPaddressassignedto

thePDU.Youshouldbepromptedfora

password

A

. The user name is admin

and the default password is admin.

After you enter the user name and

password,thePowerAlertstatuspage

B

willappearinthebrowserwindow.

Formoreinformationabout

configurationandoperationofthePDU

viathePowerAlertinterface,refertothe

SNMPWEBCARDUser'sGuide,included

ontheCD-ROMbundledwiththePDU.

Note for Network Management System Users

Only: Two MIB files - Tripplite.mib and

RFC1628.mib - must be loaded on each

Network Management Station that will

monitor the PDU via SNMP. The files are

provided on the CD-ROM included in the

product package.

Installation continued

A

B

13-11-194-933093.indb 7 12/5/2013 5:22:00 PM

8

Input Plug Adapter (Select Models): ConvertsthePDU's

twist-lockinputplugtoastraight-bladeinputplug.

Power Inlet (Select Models): TheIECpowerinletconnectsto

theincludedpowercordoracompatibleuser-suppliedpower

cord.Theinletincludesabrackettosecurethecordconnection.

IEC 309 3-Pole Input Plug:Availableonselectmodels.

Outlets (Vary by Model): Duringnormaloperation,theoutlets

distributeACpowertoconnectedequipment.Selectmodels

featureanLEDthatindicatesoutletstatus.

Outlet LEDs: Onswitchedmodels,eachoutletLEDilluminates

whentheassociatedoutletisreadytodistributeliveACpower.

Digital Load Meter (Ammeter): The total connected

equipmentloadinamperesisdisplayedbythedigitalmeter

A

.

20-ampmodelsfeatureaScrollIP/RotateSwitch

B

.Pressthis

switchforonesecondtodisplaythePDU’sIPaddress(two

charactersatatime).PressfortwosecondstorotatetheLED

display for ease of reading in vertical installations with the input

cordatthetoporbottomofthePDU.30-ampmodelsfeaturea

Select/RotateSwitch

C

andadedicatedScrollIPSwitch

D

.

PresstheSelect/RotateSwitchoncetodisplaythetotalload(in

amps)onthePDU.PressagaintodisplaytheloadonBank1of

thePDUandagaintodisplaytheloadonBank2.TheLoadBank

LEDs

E

willindicatedisplaystatusasfollows.Bothoutletbank

LEDsilluminated:totalPDUloaddisplayed.Bank1orBank2

LEDilluminated:loadoncorrespondingloadbankdisplayed.

PresstheSelect/RotateSwitchfortwosecondstorotatetheLED

display for ease of reading in vertical installations with the input

cordatthetoporbottomofthePDU.

Features

IEC-60320-C132-PositionIEC-60320-C13 IEC-60320-C19

.8.8

Scroll I

P

/

Rota

t

e

LOAD (AMPS)LOAD (AMPS)

Bank1

Bank2

Scroll

IP

LOAD (AMPS)

Select /

Rotate

30 Amp 20 Amp

A

C

A

D

E

B

13-11-194-933093.indb 8 12/5/2013 5:22:03 PM

9

Features continued

Circuit Breakers (Select Models):Iftheconnected

equipmentloadonaloadbankexceedstheMaximumLoad

Ratingoftheloadbank,thecircuitbreakerwilltrip.Disconnect

excessequipmentandswitchbreakertotheonpositiontoreset

thebreaker.Modelswithmultipleoutletbankshaveacircuit

breakerforeachbank.Circuitbreakersareonlyusedtoprotect

outputloadbanks.

Cord Retention Bracket (Select Models):Providessecure

attachment points for connected equipment cords.

C14 Plug Sleeve: (Optional)UsetheincludedC14plastic

sleeves to secure plugs to C13 receptacles. Attach the sleeve to

theplugmakingsurethatthepulltabsremainoutsidetheplug

andthatthefitissecure.Tounplugequipmentproperly,usethe

pulltabstoremovetheplugandsleevefromthereceptacle.

C20 Plug Sleeve: (Optional)UsetheincludedC20plastic

sleevestosecureplugstoC19receptacles.Attachthesleeveto

theplugmakingsurethatthepulltabsremainoutsidetheplug

andthatthefitissecure.Tounplugequipmentproperly,usethe

pulltabstoremovetheplugandsleevefromthereceptacle.

Mounting Brackets:UsethesebracketstomountthePDU.

PDUMVROTATEBRKT Mounting Accessory: Usethese

V-shapedbracketstomountthePDUwithitsoutletsfacingthe

rearoftherack.

SNMP Reset Button: Presstheresetbutton

A

for 3 seconds

torebootthePDU'snetworkcard.Rebootingthenetworkcard

willnoterasenetworksettingsorinterruptACpower.Thereset

buttonisrecessed;useasuitabletooltopressit.

ACCY Port: Theportisreservedforfutureexpansion.

24 23 22 21

20

19 18 17 16 15

14

13

ENVIROSENSEENVIROSENSE

CONFIGCONFIGACCYACCY

RESETRESET

LINKLINK

STATUSSTATUS

12

11 10 9 8 7

6 5 4 3

2 1

INLET

A

13-11-194-933093.indb 9 12/5/2013 5:22:05 PM

10

Configuration and Operation

Remote Monitoring and Control

ThePDUprovidesremotemonitoring

A

,

outlet control

B

andmoreviaWebbrowser,

telnetandSNMP-basedNetwork

ManagementSystems.Formoreinformation

aboutconfigurationandoperationofthe

PDUviathePowerAlertWebbrowser

interface,refertotheSNMPWEBCARDUser's

Guide,includedontheCD-ROMbundled

withthePDU.

Features continued

PS/2 Port: UsethisporttoconnectaTrippLiteENVIROSENSE

environmental sensor to provide remote temperature/humidity

monitoring and a dry contact interface to control and monitor

alarm,securityandtelecomdevices.Visitwww.tripplite.comfor

orderinginformation.Note:Donotconnectakeyboardormouse

to this port.

RJ-45 Configuration Port: Usethisporttoprovideadirect

terminal connection to a computer with a terminal emulation

program.AnRJ-45cableisincludedwiththePDU.Ifyouneeda

replacementcable,visitwww.tripplite.comforordering

information.

Ethernet Port: UsethisRJ-45jacktoconnectthePDUtothe

networkwithastandardEthernetpatchcable.TheLinkLED

A

andStatusLED

B

indicateseveraloperatingconditions,as

showninthetablebelow.This port is not compatible with PoE

(Power Over Ethernet) applications.

Network Operating Conditions

A

Link LED Color

Off NoNetworkConnection

FlashingAmber 100MbpsNetworkConnection

FlashingGreen 10MbpsNetworkConnection

B

Status LED Color

Off CardNotInitialized

SteadyGreen CardInitializedandOperational

FlashingAmber Error-CardNotInitialized

A

B

A

B

13-11-194-933093.indb 10 12/5/2013 5:22:06 PM

11

Warranty and Warranty Registration

LIMITED WARRANTY

Sellerwarrantsthisproduct,ifusedinaccordancewithallapplicableinstructions,tobefreefromoriginaldefects

inmaterialandworkmanshipforaperiodof2years(exceptinternalUPSsystembatteriesoutsideUSAand

Canada, 1 year) from the date of initial purchase. If the product should prove defective in material or

workmanshipwithinthatperiod,Sellerwillrepairorreplacetheproduct,initssolediscretion.Serviceunderthis

Warrantycanonlybeobtainedbyyourdeliveringorshippingtheproduct(withallshippingordeliverycharges

prepaid)to:TrippLite,1111W.35thStreet,Chicago,IL60609USA.Sellerwillpayreturnshippingcharges.

Visitwww.tripplite.com/supportbeforesendinganyequipmentbackforrepair.

THISWARRANTYDOESNOTAPPLYTONORMALWEARORTODAMAGERESULTINGFROMACCIDENT,MISUSE,

ABUSEORNEGLECT.SELLERMAKESNOEXPRESSWARRANTIESOTHERTHANTHEWARRANTYEXPRESSLYSET

FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,

INCLUDINGALLWARRANTIESOFMERCHANTABILITYORFITNESS,ARELIMITEDINDURATIONTOTHEWARRANTY

PERIODSETFORTHABOVE;ANDTHISWARRANTYEXPRESSLYEXCLUDESALLINCIDENTALANDCONSEQUENTIAL

DAMAGES.(Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,andsomestatesdonot

allowtheexclusionorlimitationofincidentalorconsequentialdamages,sotheabovelimitationsorexclusions

maynotapplytoyou.ThisWarrantygivesyouspecificlegalrights,andyoumayhaveotherrightswhichvary

fromjurisdictiontojurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable,

adequate or safe for the use intended. Since individual applications are subject to great variation, the

manufacturermakesnorepresentationorwarrantyastothesuitabilityorfitnessofthesedevicesforanyspecific

application.

WARRANTY REGISTRATION

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be

automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

*Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.Seewebsitefordetails.

FCC Notice

Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)This

devicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,including

interference that may cause undesired operation.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,pursuanttopart

15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterference

whentheequipmentisoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiate

radiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructionmanual,maycause

harmfulinterferencetoradiocommunications.Operationofthisequipmentinaresidentialareaislikelytocause

harmfulinterferenceinwhichcasetheuserwillberequiredtocorrecttheinterferenceathisownexpense.The

usermustuseshieldedcablesandconnectorswiththisproduct.Anychangesormodificationstothisproduct

notexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthoritytooperatethe

equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been

assignedauniqueseriesnumber.Theseriesnumbercanbefoundontheproductnameplatelabel,alongwith

allrequiredapprovalmarkingsandinformation.Whenrequestingcomplianceinformationforthisproduct,always

refertotheseriesnumber.Theseriesnumbershouldnotbeconfusedwiththemarkingnameormodelnumber

of the product.

TrippLitefollowsapolicyofcontinuousimprovement.Specificationsaresubjecttochangewithoutnotice.

13-11-194-933093.indb 11 12/5/2013 5:22:06 PM

12

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

13-11-194-933093.indb 12 12/5/2013 5:22:06 PM

Page is loading ...

Tripp Lite PDUMV30HVNET Owner's manual

This manual is also suitable for

Tripp Lite PDUMV30HVNET Owner's manual

in other languages

Related papers

Other documents