Sparky Group HD Professional HeavyDuty SMA 18Li HD User manual

DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product, described under “Technical specications”, fulls all the relevant provisions

of the following directives and the harmonized standards:

2006/42/EU, 2014/30/EU, 2011/65/ЕU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Technical le is stored at SPARKY ELTOS AD, Kubrat Str. 9, 5500 Lovech, Bulgaria.

KONFORMITÄTSERKLÄRUNG

Hiermit versichern wir unsere persönliche Haftung, dass Produkt im Abschnitt “Technische Daten“ beschrieben“ allen einschlägigen

Bestimmungen folgender Richtlinien und entsprechender harmonisierten Standards entspricht:

2006/42/EU, 2014/30/EU, 2011/65/ЕU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Die technischen Unterlagen werden bei SPARKY ELTOS AD, Kubrat Str.9, 5500 Lovech, Bulgarien, aufbewahrt.

DECLARATION DE CONFORMITE

Nous déclarons sous notre responsabilité que le produit décrit dans la rubrique “Données techniques” satisfait à l’ensemble des

dispositions pertinentes des présentes directives, respectivement aux normes harmonisées:

2006/42/UE, 2014/30/UE, 2011/65/UE, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Le dossier technique est conservé par SPARKY ELTOS AD, 9, rue Kubrat, 5500 Lovech, Bulgarie.

DICHIARAZIONE DI CONFORMITÀ

Noi dichiariamo sotto la nostra personale responsabilità, che il prodotto, descritto nella sezione “Dati tecnici” è in conformità a tutte le

disposizioni pertinenti della presente direttive e norme armonizzate:

2006/42/UE, 2014/30/UE, 2011/65/UE, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Il fascicolo tecnico viene custodito presso la SPARKY ELTOS AD, 5500 Lovech, via Kubrat n. 9, Bulgaria.

DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que el producto, descrito en los “Datos técnicos”, está conforme con todas las

disposiciones aplicables de la presente directrices aplicables y las correspondientes normas armonizadas:

2006/42/UE, 2014/30/UE, 2011/65/UE, 2011/65/EU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

El expediente técnico está archivado en SPARKY ELTOS SA, C/ Kubrat, 9, 5500 Lovech, Bulgaria.

DECLA RAÇÃO DE CONFORMIDADE

Declaramos assumindo a nossa responsabilidade pessoal que el producto, descrito en los “Dados técnicos”, está conforme com todas

as disposições relevantes da presente directrizes aplicáveis e respectivos estandartes harmonizados:

2014/35/UE, 2014/30/UE, 2011/65/UE, 2011/65/EU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

A documentação técnica guarda-se no SPARKY ELTOS AD, rua Kubrat 9, 5500, Lovech, Bulgária.

DEKLARACJA ZGODNOŚCI

Niniejszym deklarujemy naszą osobistą odpowiedzialnością, że produkt, przedstawiony w rozdziale „Dane techniczne“, pełnia wszystkie

odpowiednie postanowienia następujących dyrektyw i harmonizowanych standardów:

2006/42/WE, 2014/30/UE, 2011/65/UE, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Teczka techniczna przechowywana jest w SPARKY ELTOS AD, Kubrat Str.9, 5500 Lovech, Bułgaria.

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ

Мы заявляем со всей ответственностью, что продукт, описанный в разделе “Технические данные“, полностью соответствует

всем соответствующим требованиям действующих директив и гармонизированных стандартов:

2006/42/EU, 2014/30/EU, 2011/65/ЕU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Техническое досье хранится в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, Болгария.

ДЕКЛАРАЦІЯ ПРО ВІДПОВІДНІСТЬ

Ми заявляємо під свою власну відповідальність, що продукт, описаний у розділі “Teхнічні дані“ відповідає всім діючим вимогам

директив і гармонізованих стандартів:

2006/42/EU, 2014/30/EU, 2011/65/ЕU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Технічне досьє зберігається в СПАРКИ ЕЛТОС АД, ул. Кубрат № 9, 5500 Ловеч, Болгарія.

ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ

Ние декларираме на своя лична отговорност, че изделието, описано в раздел “Технически данни”, отговаря на всички

приложими изисквания на следните директиви и хармонизирани стандарти:

2006/42/EU, 2014/30/EU, 2011/65/ЕU, EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN 50581.

Техническото досие се съхранява в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, България.

6 March 2017

Manufacturer

SPARKY Power Tools GmbH

Leipziger Str. 20

10117 Berlin, GERMANY

Signature of authorized person

A. Ivanov

Technical director of SPARKY ELTOS AD

18 V Lithium-Ion

SMA 18Li HD

149315 1803R01

1 – 9

CORDLESS FLAT HEAD SANDER

Original instructions

20 – 29

PONCEUSE À BATTERIE À TÊTE PLATE

Notice originale

70 – 80

АККУМУЛЯТОРНАЯ ШЛИФМАШИНА С ПЛОСКОЙ ГОЛОВКОЙ

Оригинальная инструкция по эксплуатации

81 – 90

АКУМУЛЯТОРНА ШЛIФМАШИНА З ПЛОСКОЮ ГОЛОВКОЮ

Оригінальна інструкція з експлуатації

91 – 101

АКУМУЛАТОРНА ШЛИФОВЪЧНА МАШИНА С ПЛОСКА ГЛАВА

Оригинална инструкция за използване

10 – 19

AKKU-FLACHKOPFSCHLEIFER

Originalbetriebsanleitung

60 – 69

BEZPRZEWODOWA SZLIFIERKA Z PŁASKĄ GŁOWICĄ

Instrukcja oryginalna

30 – 39

LEVIGATRICE A BATTERIA RICARICABILE A TESTA PIANA

Istruzioni originali

50 – 59

LIXADEIRA SEM FIO DE CABEÇA CHATA

Instrução original para o uso

40 – 49

AMOLADORA INALAMBRICA DE CABEZAL PLANO

Instrucciones de uso originales

www.sparky.eu

BLACK PANTONE185

Page is loading ...

1

Original instructions

EN

UNPACKING

Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is missing. If you nd

anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectied. Failure to do

so could result in serious personal injury.

ASSEMBLY

The cordless at head sander is packed fully assembled.

Contents

Introduction ..........................................................................................................................................................................1

Technical specications ......................................................................................................................................................3

General power tool safety warnings ..................................................................................................................................4

Additional safety rules for at head sanders .....................................................................................................................5

Know your product ..............................................................................................................................................................6

Operation..............................................................................................................................................................................7

Maintenance .......................................................................................................................................................................8

Warranty ...............................................................................................................................................................................9

Introduction

Your new SPARKY power tool will more than satisfy your expectations. It has been manufactured under stringent

SPARKY Quality Standards to meet superior performance criteria. You will nd your new tool easy and safe to operate,

and, with proper care, it will give you many years of dependable service.

WARNING:

Carefully read through this entire Instruction Manual before using your new SPARKY power tool. Take special

care to heed the Warnings. Your SPARKY power tool has many features that will make your job faster and

easier. Safety, performance, and dependability have been given top priority in the development of this tool,

making it easy to maintain and operate.

Do not dispose of electrical products together with household waste!

Waste electrical products should not be disposed of with household waste. Please recycle where facilities

exist. Check with your local authority or retailer for recycling advice.

ENVIRONMENTAL PROTECTION

The machine, accessories and packaging should be sorted for environmental-friendly recycling.

The plastic components are labelled for categorised recycling.

pages_SMA 18LiHD-2016.indd 1 6.3.2018 г. 8:35:26

2

EN

SMA 18Li HD

DESCRIPTION OF SYMBOLS

The rating plate on your tool may show symbols. These represent important information about the product or instruc-

tions on its use.

There are symbols on the battery pack. These represent important information about the product or instructions on its

use.

Recycle Li-Ion battery packs!

Do not heat, protect from direct exposure to sun and re!

Do not wet, protect from rain and water!

Admissible charging temperature range 0-45

о

С

Hoop-and-loop fastening.

Always wear eye protection

Conforms to the relevant European Directives

Conforms to the requirements of Russian standards

Refer to original instructions.

YYYY-Www

Production period, where the variable symbols are:

YYYY - year of manufacture, ww - calendar week number

SMA CORDLESS FLAT HEAD SANDER

pages_SMA 18LiHD-2016.indd 2 6.3.2018 г. 8:35:26

3

Original instructions

EN

The vibration emission level given in this information sheet has been measured in accordance with a standardised test

given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of

exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for dif-

ferent applications, with different accessories or poorly maintained, the vibration emission may differ. This may signi-

cantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched

off or when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total

working period.

Maintain the power tool and the accessories and keep your hands warm during operation to reduce the harmful effect

of vibrations.

Other applications such as cutting-off or wire brushing may have different vibration emission values.

Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful. Contact

with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders.

Certain kinds of dust are classied as carcinogenic such as oak and beech dust especially in conjunction with additives

for wood conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists.

▪ Where the use of a dust extraction device is possible it shall be used.

▪ The work place must be well ventilated.

▪ The use of a dust mask of lter class P2 is recommended.

Follow national requirements for the materials you want to work with.

Technical specications

Model SMA 18Li HD

▪ Rated voltage V 18

▪ Rated speed min

-1

2800

▪ Sanding head diameter mm 150

▪ Max. operating tool diameter mm 150

▪ Sanding head height mm 15

▪ Rated output W 400

▪ Battery capacity (Li-ion) Ah 4

▪ LED charge indicator ●

▪ Soft start ●

▪ Non-self starting safety (NVR) ●

▪ Overload protection ●

▪ Weight (EPTA Procedure 01/2014) kg 3.1

NOISE AND VIBRATION INFORMATION (Measured values determined according to EN 60745.)

▪ Noise emission

A-weighted sound pressure level L

pA

dB(A) 79

Uncertainty К

pA

dB 3

A-weighted sound power level LwA dB(A) 90

Uncertainty К

wA

dB 3

Wear hearing protection!

▪ Vibration emission (The vibration emission values are determined according to 6.2.7 EN 60745)

Total vibration values (vector sum in the three axes) determined according to EN 60745:

Sanding

Vibration emission value a

h,AG

m/s

2

10.4

Uncertainty К

AG

m/s

2

1.5

pages_SMA 18LiHD-2016.indd 3 6.3.2018 г. 8:35:26

4

EN

SMA 18Li HD

General power tool

safety warnings

WARNING! Read all safety warnings and

all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or

serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1. WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while op-

erating a power tool. Distractions can cause you

to lose control.

2. ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Un-

modified plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords in-

crease the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

3. PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such as

dust mask, non-skid safety shoes, hard hat, or hear-

ing protection used for appropriate conditions will

reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, en-

sure these are connected and properly used.

Use of dust collection can reduce dust-related haz-

ards.

4. POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that can-

not be controlled with the switch is dangerous and

must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing ac-

cessories, or storing power tools. Such preven-

tive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

pages_SMA 18LiHD-2016.indd 4 6.3.2018 г. 8:35:26

5

Original instructions

EN

5. BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire

when used with another battery pack.

b) Use power tools only with specifically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a fire.

d) Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

6. SERVICE

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

Additional safety rules for at

head sanders

Safety Warnings Common for Sanding or Pol-

ishing Operations:

a) This power tool is intended to function as a

sander or polisher. Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow

all instructions listed below may result in electric

shock, fire and/or serious injury.

b) This power tool is not recommended for Grind-

ing, Wire Brushing or Abrasive Cutting-Off

Operations. Operations for which the power tool

was not designed may create a hazard and cause

personal injury.

c) Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) The arbour size of wheels, flanges, backing

pads or any other accessory must properly

fit the spindle of the power tool. Accessories

with arbour holes that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

g) Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting

and installing an accessory, position yourself

and bystanders away from the plane of the

rotating accessory and run the power tool at

maximum no-load speed for one minute. Dam-

aged accessories will normally break apart during

this test time.

h) Wear personal protective equipment. Depend-

ing on application, use face shield, safety gog-

gles or safety glasses. As appropriate, wear

dust mask, hearing protectors, gloves and

workshop apron capable of stopping small

abrasive or workpiece fragments. The eye pro-

tection must be capable of stopping flying debris

generated by various operations. The dust mask

or respirator must be capable of filtrating particles

generated by your operation. Prolonged exposure

to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

j) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact hid-

den wiring. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power

tool “live” and could give the operator an electric

shock.

k) Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

l) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the ac-

cessory into your body.

m) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

n) Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

o) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

▪ Thetoolmustbeusedonlyforitsprescribed

purpose. Any use other use than those men-

tioned in this Instruction will be considered a

case of misuse. The user and not the manufac-

turer shall be liable for any damage or injury result-

ing from such cases of misuse.

▪ The manufacturer shall not be liable for any

changes made to the tool nor for any damage

resulting from such changes.

pages_SMA 18LiHD-2016.indd 5 6.3.2018 г. 8:35:26

6

EN

SMA 18Li HD

▪ Whenoperatingindustyenvironment,theven-

tilation slots must be kept clean. If it should be-

come necessary to clear dust, first disconnect

the tool from the mains supply (remove the

battery) use non metallic objects to clean the

dust and avoid damaging internal parts. The

power tool will overheat under deteriorated

cooling due to the clogged with dust ventila-

tion slots.

Further safety instructions for all operations

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is enter-

ing into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or in-

correct operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and posi-

tion your body and arm to allow you to resist

kickback forces. Always use auxiliary handle,

if provided, for maximum control over kick-

back or torque reaction during start-up. The

operator can control torque reactions or kickback

forces, if proper precautions are taken.

b) Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

c) Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control.

▪ Fixthemachinedpieceinviceorinanotherap-

propriate way.

SafetyWarningsSpecicforSandingOpera-

tions:

a) Do not use excessively oversized sanding disc

paper. Follow manufacturer’s recommenda-

tions, when selecting sanding paper. Larger

sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snag-

ging, tearing of the disc or kickback.

SafetyWarningsSpecicforPolishingOpera-

tions:

a) Do not allow any loose portion of the polish-

ing bonnet or its attachment strings to spin

freely. Tuck away or trim any loose attach-

ment strings. Loose and spinning attachment

strings can entangle your fingers or snag on

the workpiece.

Additional Safety Warnings

▪ Before removing the battery release the ON/OFF

switch and place it in OFF position. This prevents

uncontrolled startup of the machine upon inserting the

battery and avoids activation of the built-in non-self

starting safety (NVR).

▪ When working stone, use dust extraction. The

vacuum cleaner must be approved for the extrac-

tion of stone dust. Using this equipment reduces

dust-related hazards.

▪ While operating the machine, always hold it firmly

with both hands and provide for a secure stance.

The power tool is guided more securely with both

hands.

▪ Use clamps or a vice to secure your work when-

ever possible.

▪ Keep work area clean. Blends of materials are par-

ticularly dangerous. Dust from light alloys can burn or

explode.

▪ Always use correct SPARKY battery pack (the

one supplied with tool or a replacement pack ex-

actly like it). Never install any other battery pack.

It will ruin your tool and may create a hazardous con-

dition.

Know your product

Before using the power tool, familiarize yourself with all

the operating features and safety requirements.

Use the tool and accessories only for the applications

intended. All other applications are expressly ruled out.

1. Pad

2. Spindle lock button

3. ON/OFF switch

4. Battery

5. Battery release button

6. Filter*

7. Auxiliary handle

8. Sanding head

9. Tooth belt

10. Tightening screw

11. Screw

12. LED battery state indicator button

13. LED battery state indicator

14. LED overload indicator

15. Charger

16. Screw

17. Screw

18. Adjusting screw

19. Washer

20. Driven pulley

21. Cap

22. Screw

23. Driving pulley

24. Washer

pages_SMA 18LiHD-2016.indd 6 6.3.2018 г. 8:35:26

7

Original instructions

EN

ACCESSORIES TO BE USED WITH THIS

POWER TOOL

25. Hook-and-loop sandpaper (Velcro type)*

26. Hook-and-loop foam pad (Velcro type)*

* The additional accessories shown in the illustrations or

described in the text are not included in the delivery.

Operation

This power tool is designed for rough and ne dry sand-

ing and polishing difcult to access metal or wood sur-

faces by means of sandpaper, felt wheels or foam pads

(Velcro type), for example for sanding window shutters,

gaps or radiator ns.

WARNING: Operating this power tool with

accessories, different from the described herewith,

may cause accident during operation. The possibility

to attach an accessory to the machine does not imply

that the machine is designed to be operated with it!

Any use of this tool with accessories, different from the

described herewith, and the resulting danger for your

health are entirely AT YOUR OWN RISK.

PRIOR TO INITIAL OPERATION

▪ Check the position of ON/OFF switch. The battery

shall be connected and disconnected to the pow-

er tool only when the switch is in OFF position. If

the battery is connected to the power tool with the

switch in ON position, the machine will not start, be-

cause the non-self starting safety (NVR) will be ac-

tuated. To start the power tool you must first switch

it off and then on again.

WARNING: Always switch off the power tool

and remove the battery prior to any adjustment, servic-

ing or maintenance.

▪ Check if the operating tool diameter does not exceed

the size stated in the specifications.

▪ Check that the auxiliary handle is properly mounted

and reliably tightened.

▪ Check that the fixing screws (10) are firmly fastened

and tighten them if necessary.

FITTING AND REMOVING THE

BATTERY PACK (Fig. 1)

To remove the battery: Press release button (5) in the

indicated direction and pull the battery out of the ma-

chine body.

To insert the battery: Place the battery into the base of

the machine and slide it until it locks with an audible click.

BATTERY STATE INDICATOR (Fig.2)

Battery state can be checked on the LED display (13).

To activate the indicator, press button (12).

Battery capacity: 60 - 100%

Battery capacity: 30 - 60%

Battery capacity: < 30%

Blinking light

Battery capacity: < 20%. The battery

must be recharged.

Blinking light

Problems with battery. The display is

activated upon pressing the trigger of

the switch. It may show one of the fol-

lowing battery states:

▪ Low battery► Battery has to be

recharged;

▪ Temperature protection has been

actuated ► Battery must be cooled

down prior to resuming operation;

▪ Damaged or unrecognized battery

► Battery has to be replaced

Blinking light

Current overload: The display is

active during operation with the ma-

chine. Upon current overload the pro-

tection switches off the machine. To

restore normal operation rst switch

off and then on switch (3).

Non-self starting safety (NVR).

Indication is activated upon connect-

ing battery to machine with its switch

in ON position. To run the machine

you must rst switch off and then on

switch (3).

SWITCHING ON - SWITCHING OFF

Switching on: Push the back end of the ON/OFF switch

(3) down and then forward in the direction of the arrow

until its front end will sag, thus xing itself.

Switching off: press the back, lifted end of switch (3)

and release it to return in its initial position.

SELECTING THE ACCESSORY AND

PREPARATION FOR OPERATION

The choice of the accessory depends on the intended

operation. Generally the operations you are allowed to

perform are:

- Sanding with sandpaper;

- Sanding with felt wheel;

- Polishing with a foam pad.

USING THE OPERATING TOOL

The selection of sandpaper depends on the desired

surface quality. For rough operations use sandpaper

with larger grit size, and for ne and nishing operations

use sandpaper with smaller grit size to achieve surface

smoothness.

Use only hook-and-loop sanding accessories (Velcro

type).

Do not use sanding accessories with diameter exceed-

ing the maximum diameter permitted for this power tool.

pages_SMA 18LiHD-2016.indd 7 6.3.2018 г. 8:35:26

8

EN

SMA 18Li HD

MOUNTING THE OPERATING TOOL

The precise and accurate performance of the below

described procedures guarantees the reliable and safe

operation with the power tool.

1. Ensure the battery is removed from the power tool.

2. Turn the machine in a way ensuring access to the

operating tool. We recommend xing the machine

in stationary position. Thus it would be possible to

use both hands for convenient and safe assembly.

3. Mount the selected operating tool ensuring its co-

axial positioning.

4. Press frontally the selected operating tool to the pad

(1) to ensure maximum cohesion of the hook-and-

loop surfaces (Velcro type).

5. Turn the machine with the sandpaper facing down-

ward.

6. Insert the battery into the power tool.

7. Slide the ON/OFF switch (3) forward to start the ma-

chine.

8. Let the machine operate at no load for approximate-

ly one minute not allowing the sanding head (8) to

contact any surface.

9. At the event of increased vibrations or other symp-

toms not typical for operation, stop the machine im-

mediately and search for the reason. If you cannot

detect the reason yourself - contact the nearest au-

thorised SPARKY service centre. Operating with a

faulty machine may cause an accident!

10. If no trouble is detected then you can start opera-

tion.

REPLACING THE OPERATING TOOL

1. Ensure the battery is removed from the power tool.

2. Turn the machine in a way ensuring access to the

operating tool. We recommend xing the machine

in stationary position. Thus it would be possible to

use both hands for convenient and safe assembly.

3. Remove the clogged operating tool.

4. Follow steps 3 - 10 described in section “Mounting

the operating tool”.

REPLACING THE TOOTH BELT

1. Ensure the battery is removed from the power tool.

2. Unwind the four screws (11) in order to remove the

pad (1) together with the driven belt pulley (20).

3. Unwind both end screws (17) and remove the cap

(21).

4. Remove the tooth belt (9) from the driving belt pulley

(23).

5. Take the worn-out tooth belt (9) out from the housing

and mount the new tooth belt into the housing.

6. Mount the pad (1) together with the driven belt pulley

(20) and x it by the four screws (11).

7. Slightly loosen the three screws (22) and unwind

screw (18), so that the sanding head (8) be able to

move back.

8. Mount the tooth belt (9) to the driven belt pulley (20)

by engaging the belt teeth to the belt pulley teeth.

9. Adjust the tensioning of the tooth belt by turning

screw (18); upon tightening the screw, the sanding

head (8) will move forward and the belt will stretch;

upon loosening the screw, the tooth belt will loos-

en. The proper tensioning is achieved when the

distance from the ange back side to the surface

supported by screw (18) is 5,3 mm. When you have

already tensioned the belt, fasten screws (22) until

the sanding head is xed rmly.

10. Mount the cap (21) and x it by both end screws (17).

11. Turn the machine with the exible pad facing down-

ward

12. Insert the battery into the power tool.

13. Slide the ON/OFF switch (3) forward to start the ma-

chine.

14. Let the machine operate at no load for approximate-

ly one minute not allowing the sanding head (8) to

contact any surface.

15. At the event of increased vibrations or other symp-

toms not typical for operation, stop the machine im-

mediately and search for the reason. If you cannot

detect the reason yourself - contact the nearest au-

thorised SPARKY service centre. Operating with a

faulty machine may cause an accident!

16. If no trouble is detected then you can start opera-

tion.

AUXILIARY HANDLE

The machine is delivered with the auxiliary handle (7)

mounted. Prior to initial operation tighten the auxiliary

handle in the desired position by tightening bolts (16).

MOUNTING AND DISMOUNTING THE

AUXILIARY HANDLE

1. Ensure the battery is removed from the power tool.

2. Mounting and dismounting the auxiliary handle

(7) is performed by screwing and unscrewing the

screws (16). Place washer (24) under screw (16).

Place washer (19) between the auxiliary handle

plate and the gearbox.

TURNING THE MACHINE CASE

The machine case can be turned to 90° or to 180°. Turn-

ing must be carried out in a specialised service centres

for SPARKY power tools.

RECOMMENDATIONS

When sanding and polishing do not apply pressure

to the processed surface by rearing down

on the machine but move the machine smoothly.

Maintenance

WARNING: Always switch off the power tool

and remove the battery prior to any adjustment, servic-

ing, maintenance.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they are

properly tightened. Should any of the screws be loose,

retighten it immediately to avoid hazards.

pages_SMA 18LiHD-2016.indd 8 6.3.2018 г. 8:35:26

9

Original instructions

EN

CLEANING

For safe operation always keep the machine and its ven-

tilation slots clean.

Regularly check to see if any dust or foreign matter

has entered the ventilation slots and the grills around

the switches. Use a soft brush and/or air jet to remove

any accumulated dust. Wear safety glasses to protect

your eyes whilst cleaning.

Exterior plastic parts may be cleaned with a damp cloth

and mild detergent if necessary.

When operating in heavily dusty environment (cutting

stone) the ventilation slots and the switch slider of the

machine running at no load must be obligatory cleaned

after each shift by compressed air or by gently tapping it

near the ventilation slots with non-metal object .

If the machine is equipped with a lter (6) on the venti-

lation slots it has to be removed and cleaned and then

placed again on the machine.

WARNING: Never use alcohol, petrol or other

cleaning agent. Never use caustic agents to clean

plastic parts.

WARNING: Water must never come into con-

tact with the tool.

IMPORTANT! To assure product safety and reliability,

repairs, maintenance and adjustment should be per-

formed by certied service centres or other qualied

service organisations, always using genuine replace-

ment parts.

Warranty

The guarantee period for SPARKY power tools is deter-

mined in the guarantee card.

Faults due to normal wear, overloading or improper han-

dling will be excluded from the guarantee.

Faults due to defective materials implemented as well as

defects in workmanship will be corrected free of charge

through replacement or repair.

The complaints for defective SPARKY power tools will

be recognized if the machine is sent back to the dealer

or is presented to the authorised warranty service centre

undismantled, in its initial condition.

Notes

Carefully read the entire Instruction Manual before using

this product.

The manufacturer reserves the right to make changes

and improvements to the products and to alter specica-

tions without prior notice.

Specications may differ from country to country.

pages_SMA 18LiHD-2016.indd 9 6.3.2018 г. 8:35:26

Page is loading ...

pages_SMA 18LiHD-2016.indd 102 6.3.2018 г. 8:35:30

pages_SMA 18LiHD-2016.indd 103 6.3.2018 г. 8:35:30

1803R01

pages_SMA 18LiHD-2016.indd 104 6.3.2018 г. 8:35:30

Sparky Group HD Professional HeavyDuty SMA 18Li HD User manual

This manual is also suitable for

Sparky Group HD Professional HeavyDuty SMA 18Li HD User manual

in other languages

Related papers

Other documents