Metabo BE 10 Operating instructions

Page is loading ...

ENGLISHen

8

Original instructions

We, being solely responsible, hereby declare that

these drills, identified by type and serial number *1),

meet all relevant requirements of directives *3) and

standards *3). Technical documents for *4) - see

page 3.

The drill is suitable for drilling in metal, wood, plastic

and similar materials, and also for screwing

operations.

The user bears sole responsibility for damage

caused by improper use.

Generally accepted accident prevention

regulations and the enclosed safety information

must be observed.

WARNING – Reading the operating

instructions will reduce the risk

of injury.

WARNING Read all safety warnings and

instructions. Failure to follow all safety

warnings and instructions may result in electric

shock, fire and/or serious injury.

Keep all safety instructions and information for

future reference.

Before using the power tool, carefully read through

and familiarise yourself with all the enclosed safety

information and the Operating Instructions. Keep all

enclosed documentation for future reference, and

pass on your power tool only together with this

documentation.

For your own protection and the

protection of your power tool, observe the

passages marked by this symbol!

Hold the power tool by insulated gripping

surfaces when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory

contacting a "live" wire may make exposed

metal parts of the power tool "live" and shock the

operator.

Pull the plug out of the plug socket before any

adjustments or servicing are performed.

Take care to avoid gas, electricity, and water

supplies!

Avoid inadvertent starts by always unlocking the

switch when the plug is removed from the mains

socket or in case of a power cut.

Keep hands away from the rotating tool!

Remove chips and similar material only with the

machine at standstill.

Caution must be exercised when driving screws into

hard materials (driving screws with metric or

imperial threads into steel)! The screw head may

break or high reverse torques may build up.

High forces are released if the tool jams or catches.

Always hold the tool firmly, ensure you have good

footing and concentrate when working.

Secure small workpieces. Clamp in a vice for

example.

Do not keep the ventilation slots closed.

Reducing dust exposure:

WARNING - Some dust created by power

sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to

cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

- Lead from lead-based paints,

- Crystalline silica from bricks and cement and

other masonry products, and

- Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are

specially designed to filter out microscopic

particles.

This also applies to dust from other materials such

as some timber types (like oak or beech dust),

metals, asbestos. Other known diseases are e.g.

allergic reactions, respiratory diseases. Do not let

dust enter the body.

Observe the relevant guidelines and national

regulations for your material, staff, application and

place of application (e.g. occupational health and

safety regulations, disposal).

Collect the particles generated at the source, avoid

deposits in the surrounding area.

Use suitable accessories for special work. In this

way, fewer particles enter the environment in an

uncontrolled manner.

Use a suitable extraction unit.

Reduce dust exposure with the following measures:

- do not direct the escaping particles and the

exhaust air stream at yourself or nearby persons

or on dust deposits,

- use an extraction unit and/or air purifiers,

- ensure good ventilation of the workplace and keep

clean using a vacuum cleaner. Sweeping or

blowing stirs up dust.

- Vacuum or wash the protective clothing. Do not

blow, beat or brush.

See page 2.

1 Chuck key (for a geared chuck)

1. Conformity Declaration

2. Specified Use

3. General Safety Instructions

4. Special Safety Instructions

5. Overview

ENGLISH en

9

2Geared chuck

3 Keyless chuck

4 Rotation selector switch

5Trigger

6 Locking button (continuous activation)

Before plugging in, check to see that the

rated mains voltage and mains frequency,

as stated on the rating label, match with your

power supply.

Always install an RCD with a maximum trip

current of 30 mA upstream.

To guarantee secure purchase of the

chuck: After initial drilling (clockwise), use a

screwdriver to firmly tighten the safety screw inside

the drill chuck. Caution left-handed thread! (see

Section 7.5)

7.1 Switching On and Off

To start the machine, press the trigger switch (5).

The speed can be changed using the trigger switch.

For continuous operation the trigger switch can be

locked using the lock button (6). To stop the

machine, press the trigger switch again.

In continuous operation, the machine

continues running if it is forced out of your

hands. Therefore, always hold the machine

with both hands using the handles provided,

stand in a safe position and concentrate.

7.2 Selection of direction of rotation

See illustration, page 2.

Do not activate the rotation selector

switch (4) unless the motor has

completely stopped.

Select direction of rotation:

R=Clockwise

L=Counter-clockwise

The drill chuck must be firmly screwed

onto the spindle and the safety screw

inside the drill chuck must be firmly tightened

with a screwdriver. (Caution, left-handed

thread!) If rotated counterclockwise (e.g. when

screwing) it could otherwise become loose.

7.3 Tool change with a geared chuck (2)

See illustrations, page 2.

Clamping tool:

Insert the tool and use the chuck key (1) to uniformly

clamp tight in all 3 bores.

Removing tool:

Open the geared chuck (2) with chuck key (1) and

remove tool.

7.4 Tool change

with keyless chuck (3)

See illustrations, page 2.

Insert tool. Hold ring (a) and turn the sleeve (b) with

your other hand in direction "GRIP, ZU" until further

rotation is impossible.

With a soft tool shank, retightening may be required

after a short drilling period.

Opening chuck: Hold ring (a) and turn the sleeve (b)

with your other hand in direction "AUF, RELEASE".

If the chuck is very securely tightened: Unplug.

Hold drill chuck using an open-end spanner at the

flats on its head and turn the sleeve (b) vigourously

in direction of "AUF, RELEASE".

7.5 Removing the chuck

Geared chuck (2)

Undo the locking screw. Caution left-handed

thread!

Hold the drill spindle tight with an open-ended

spanner. With a light blow from a rubber hammer,

release the chuck from the inserted chuck key and

unscrew it.

Keyless chuck (3)

Undo the locking screw. Caution left-handed

thread!

6. Commissioning

7. Use

ENGLISHen

10

Hold the drill spindle tight with an open-ended

spanner. With a light blow from a rubber hammer,

release the chuck from the clamped hexagon

spanner and unscrew it.

In the case of deep bores pull the drill bit out of the

bore from time to time in order to remove the bore

dust or shavings.

Keyless chuck cleaning:

After prolonged use hold the chuck vertically, with

the opening facing down, and fully open and close it

several times. The dust collected falls from the

opening. Regular use of cleaning spray on the jaws

and jaw openings is recommended.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

For a complete range of accessories, see

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by

qualified electricians ONLY!

The connection cable must only be replaced by

Metabo or an authorised customer service

workshop.

Contact your local Metabo representative if you

have Metabo power tools requiring repairs. For

addresses see www.metabo.com.

You can download a list of spare parts from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Only for EU countries: Never dispose of

power tools in your household waste! In

accordance with European Guideline 2012/

19/EU on used electronic and electric equipment

and its implementation in national legal systems,

used power tools must be collected separately and

handed in for environmentally compatible recycling.

Explanatory notes on the specifications on page 3.

Changes due to technological progress reserved.

P

1

=Nominal power input

P

2

=Power output

n

0

=No load speed

n

1

=Speed at rated load

ø max =Max. solid drill diameter

b =Chuck capacity

G=Spindle thread

H = Drill spindle with hexagon socket

m =Weight without mains cable

Measured values determined in conformity with

EN 60745.

Machine in protection class II

~ Alternating current

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

Emission values

Using these values, you can estimate the emis-

sions from this power tool and compare these with

the values emitted by other power tools. The actual

values may be higher or lower, depending on the

particular application and the condition of the tool or

power tool. In estimating the values, you should also

include work breaks and periods of low use. Based

on the estimated emission values, specify protective

measures for the user - for example, any organisa-

tional steps that must be put in place.

Vibration total value (vector sum of three directions)

determined in accordance with EN 60745:

a

h, D

=Vibration emission value

(drilling into metal)

K

h,D

=Uncertainty (vibration)

Typical A-effective perceived sound levels:

L

pA

=Sound pressure level

L

WA

=Acoustic power level

K

pA

, K

WA

= Uncertainty

During operation the noise level can exceed

80 dB(A).

Wear ear protectors!

8. Tips and Tricks

9. Maintenance

10. Accessories

11. Repairs

12. Environmental Protection

13. Technical Specifications

Page is loading ...

Metabowerke GmbH

Metabo-Allee 1

72622 Nuertingen

Germany

www.metabo.com

170 27 0640 - 0219

Metabo BE 10 Operating instructions

This manual is also suitable for

Metabo BE 10 Operating instructions

in other languages

Related papers

Other documents