Westinghouse 7200200 User manual

Page is loading ...

2

ETL-ES-Carolina-R-WH14

1. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards (ANSI/NFPA 70), including fire-rated construction.

2. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

3. After making the wire connections, gently push connections into outlet box with wire nuts pointing up. The wires should be spread apart with the grounded conductor and the equipment-grounding con

ductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.

4. Before you begin installing the fan, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

5. Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

7. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.

8. To reduce the risk of fire, electric shock, or personal injury, this fan must be mounted to an outlet box marked suitable for fan support, and use the mounting screws provided with the outlet box. (Mounting

must support at least 35 lbs.)

9. WARNING! Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

10. Attach the mounting bracket using only the hardware supplied with the outlet box. Fan is only to be mounted to an outlet box marked “Acceptable for Fan Support”.

11. WARNING! To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

12. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

13. NEVER place a switch where it can be reached from a tub or shower.

14. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufacturer’s guideline safety standards such as

those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

15. Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means can

not be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

16. All set screws must be checked and re-tightened where necessary before installation.

17. The appliance is not intended for use by young children or infirmed persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.

TOOLS REQUIRED

Phillips Screwdriver Wire Cutters Pliers Step Ladder

SAFETY TIPS

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED 'ACCEPTABLE FOR FAN SUPPORT OF 15.9 KG (35 LBS) OR LESS' AND

USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT DIRECTLY FROM BUILDING STRUCTURE. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF

.LUMINARIES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT

Page is loading ...

4

ETL-ES-Carolina-R-WH14

COMBO-BLADE

Combo-Blades feature two high quality finishes on one blade. Select the one that best complements

your decor, or change the style with just a flip of the blade.

NOTE: Combo-Blade finishes vary, depending upon model.

ASPAS DE DOBLE CARA

Las aspas del rotor de doble cara presentan dos superficies con un acabado de alta calidad. Invirtiendo

las aspas puede Ud. producir un efecto decorativo adaptado a su ambiente o crear una decoración

completamente nueva.

Observación: las superficies de las aspas de doble cara son distintas dependiendo del modelo.

FEATURES

CARACTERÍSTICAS

Page is loading ...

6

ETL-ES-Carolina-R-WH14

MOUNTING BRACKET INSTALLATION

INSTALACIÓN CON SOPORTE DE MONTAJE

Remove screws from motor bracket and mounting plate. Hang fan from

mounting plate by inserting "T"-shaped end of bracket into slot opening of

mounting plate. This will allow for hands free wiring.

Extraiga los tornillos del soporte del motor y de la placa de montaje.

Cuelgue el ventilador de la placa de montaje insertando el extremo del

soporte con forma de “T” adentro de la ranura de la placa de montaje. De

este modo, tendrá las dos manos libres para hacer el cableado.

4

3

Remove the screws and star washers (1) from the bracket as shown above.

Loosen (do not remove) the screws (2) from the bracket as shown above.

Install mounting bracket to outlet box in ceiling using the screws and washers pro-

vided with the outlet box.

Quite los tornillos y las arandelas en estrella (1) del soporte como se indica arriba.

Afloje (no quite) los tornillos (2) del soporte como se indica arriba.

Instale el soporte de montaje a la caja de embutir del techo con la tornillería incluidos

con la caja de embutir.

1

2

7

ETL-ES-Carolina-R-WH14

5

While fan is hanging from the mounting plate, connect the wires with wire connectors (included), using the following steps

for wiring options.

Mientras el ventilador está colgado de la placa de montaje, conecte los cables con los conectores para cables (incluidos)

usando los siguientes pasos para opciones de cableado.

MOUNTING

MONTAJE

8

ETL-ES-Carolina-R-WH14

7

*Connect blue wire only if attaching light kit with fan.

Follow diagram above to make wiring connections for wall control operation.

6

*Connect blue wire only if attaching light kit with fan.

Follow diagram above to make wiring connections for fan pull chain control.

PULL CHAIN WIRING OPTION

WALL CONTROL WIRING OPTION

Siga las instrucciones del diagrama anterior para hacer las conexiones de

cableado para el ventilador con control de pared.

Siga las instrucciones del diagrama anterior para hacer las conexiones de

cableado para el ventilador controlado con cadenilla de tiro.

OPCIÓN DE CABLEADO PARA CADENILLA DE TIRO

OPCIÓN DE CABLEADO PARA CONTROL DE PARED

WIRING OPTIONS

OPCIÓN DE CABLEADO

Empuje el motor hacia arriba y fije el motor

a la placa de montaje asegurando firmemente

con los tornillos y las arandelas incluidos.

Push motor upward and attach the motor to

the mounting plate by tightly securing with

screws and washers provided.

9

ETL-ES-Carolina-R-WH14

MOUNTING

MONTAJE

8

The decorative motor housing has two mating slots (1) and

two mating holes (2). Position both slots on the motor housing

directly under and in line with two screws in the mounting

bracket (3). Lift the motor housing, allowing the two screws to

slide into the mating slots. Rotate the motor housing clockwise

until both screws from the mounting bracket drop into the slot

recesses. Tighten screws securely.

El alojamiento decorativo del motor tiene dos ranuras coinciden-

tes (1) y dos agujeros coincidentes (2). Coloque ambas ranuras

del alojamiento del motor directamente abajo y en línea con los

dos tornillos del soporte de montaje (3). Eleve el alojamiento del

motor, permitiendo que los dos tornillos se deslicen dentro de

las ranuras. Gire el alojamiento del motor en sentido horario

hasta que ambos tornillos del soporte de montaje caigan aden-

tro de las ranuras. Apriete los tornillos asegurándolos.

9

Install two screws and star washers into the mating

holes of the motor housing and tighten to secure the

housing to the mounting bracket.

Instale los dos tornillos y las arandelas en estrella en

los agujeros coincidentes del alojamiento del motor y

ajústelos para asegurar el alojamiento al soporte de

montaje.

10

2

1

3

2

1

Page is loading ...

11

ETL-ES-Carolina-R-WH14

LIGHT FIXTURE INSTALLATION

INSTALACIÓN DEL ARTEFACTO LUMINOSO

13

Find the wire plugs from the light kit and from the motor and slide together. Connect the blue wire from the switch housing, to the black wire from the light kit, and the

white wire from the switch housing to the white wire from the light kit. Attach light kit to the switch housing using three small screws provided.

Identifique los conectores para cables de salida del artefacto luminoso y del motor y deslícelos para unirlos. Conecte el cable azul del alojamiento del interruptor al cable

negro del artefacto luminoso y el cable blanco del alojamiento del interruptor al cable blanco del artefacto luminoso. Conecte el artefacto luminoso al alojamiento del inter-

ruptor con los tres tornillos pequeños incluidos.

12

ETL-ES-Carolina-R-WH14

Unscrew and remove the finial (1), decorative cap (2), nut (3), and rubber/metal washer (4) from the bottom of the light kit. Install the bulbs (not included).

Desenrosque y quite el florón (1), la tapa decorativa (2), la tuerca (3) y la arandela de caucho/metal (4) de la parte inferior del juego de luces. Instale las bombillas de luz

(no incluidas).

LIGHT FIXTURE INSTALLATION

INSTALACIÓN DEL ARTEFACTO LUMINOSO

14

4

3

2

1

13

ETL-ES-Carolina-R-WH14

15

Install the glass (5) onto the light kit and tighten the washer (4) and nut (3) onto the bottom of glass. Make sure the ceiling fan pull chain is threaded through the side hole

in the bottom of the glass. Place decorative cap (2) over the bottom of glass and secure by tightening decorative finial (1).

Note: (6) Make sure the side hole on the decorative cap lines up with the side hole on the bottom of the glass so that the fan pull chain operates smoothly.

Instale la pantalla de vidrio (5) en el juego de luces y ajuste la arandela (4) y la tuerca (3) en la parte inferior de la pantalla. Asegúrese de que la cadenilla de tiro del ventila-

dor de techo pasa por el agujero lateral de la parte inferior de la pantalla. Coloque la tapa decorativa (2) sobre la parte inferior de la pantalla de vidrio y asegúrela ajustando

el florón decorativo (1).

Nota: (6) Asegúrese de que el agujero lateral de la tapa decorativa esté alineado con el agujero lateral de la parte inferior de la pantalla de vidrio para que la cadenilla de tiro

del ventilador de techo funcione sin inconvenientes.

5

4

3

2

1

6

Page is loading ...

15

ETL-ES-Carolina-R-WH14

OPERATION AND MAINTENANCE

Operation

Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off.

Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on.

The slide switch controls direction, forward or reverse.

Warm weather/down position - (Forward) Fan turns counterclockwise direction. A downward air flow creates a cooling effect as shown in illustration A.

This allows you to set your air conditioner on a higher temperature setting without affecting your comfort.

Cool weather/up position - (Reverse) Fan turns clockwise direction. An upward airflow moves warm air off the ceiling area as shown in illustration B.

This allows you to set your heating unit on a lower setting without affecting your comfort.

NOTE: Turn off and wait for fan to stop before changing the setting of the forward/reverse slide switch.

Maintenance

1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year.

Make sure they are secure.

2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning.

This could damage the motor, or the wood, or possibly cause electrical shock.

3. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer coating to minimize discoloration or tarnishing.

4. There is no need to oil your fan. The motor has permanently lubricated bearings.

Page is loading ...

17

ETL-ES-Carolina-R-WH14

TROUBLESHOOTING GUIDE

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or

wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please

check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your authorized electrician

and do not attempt any electrical repairs yourself.

TROUBLE SUGGESTED REMEDY

1. If fan does not start: 1. check main and branch circuit fuses or circuit breakers.

2. check wire connections as performed in step #6 or #7 of installation.

CAUTION: Make sure main power is turned off.

3. Make sure forward/reverse switch is firmly in up or down position.

Fan will not operate when switch is in the middle.

4. If the fan still will not start, contact a qualified electrician.

Do not attempt to troubleshoot internal electrical connections yourself.

2. If fan sounds noisy: 1. check to make sure all screws in motor housing are snug (not over tightened).

2. check to make sure the screws which attach the fan blade holder to the motor are tight.

3. Some fan motors are sensitive to signals from Solid State variable speed controls.

DO NOT USe a Solid State variable speed control.

4. Allow “break-in” period of 24 hours. Most noises associated with a new fan will disappear after this period.

3. If fan wobbles: All blades are weighed and grouped by weight. Natural woods vary in density which could cause the fan to wobble even though all blades are weight-matched. The

following procedures should eliminate most of the wobble. check for wobble after each step.

1. check that all blades are screwed firmly into blade holders.

2. check that all blade holders are tightened securely to motor.

3. Make sure that canopy and mounting bracket are tightened securely to ceiling joist.

4. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.

4. If light does not work: 1. check to see that the wire connections in the switch housing are connected.

2. check for faulty light bulbs.

3. If light kit will still not operate, contact a qualified electrician for assistance.

Page is loading ...