Heath Zenith Motion Sensor Light Control SH-5412 User manual

Brand: Heath Zenith

Model: Motion Sensor Light Control SH-5412

Category: Work lights

Type: User manual

This manual is also suitable for

SH-5412

Requirements

• Thelightcontrolrequires120-voltsAC.

• IfyouwanttouseManualMode,thecontrolmustbe

wiredthroughaswitch.

• Some codes require installation by a

qualiﬁed electrician.

• Thisproductisintendedforusewiththeenclosed

gasketandwithajunctionboxmarkedforuseinwet

locations.

LightControl

Sensor

Cover

Plate

Lamp Holders

Features

• Turnsonlightingwhenmotionisdetected.

• Automaticallyturnslightingoff.

• BulbSaver™-Extendsbulblifebyupto4xstandard

bulbs.Lightsbulbtofullbrightinunder2seconds.

• Photocellkeepsthelightingoffduringdaylighthours.

• LEDindicatesmotionwassensed(dayornight).

PlasticHanger

RubberPlug

Gasket

MountingStrap

MountingBolt

2Wire

Connectors

Thispackageincludes:

6Screws

(3sizesincluded)

OPERATION

*resetstoAutoModeatdawn.

TEST

10 5 1 TEST

ON-TIME

Put the ON-TIME switch on the

bottomofthesensorintheTEST

position.

MANUAL MODE

ON-TIME

10 5 1TEST

...backon.

AUTO

1SecondOFF

then...

Note:Whenrstturnedonwaitabout1

minutesfor

thecircuitrytocalibrate.

Manual mode only works at night

becausedaylightreturns thesensor

toAUTO.

Flipthelightswitchoffforonesecond

thenbackontotogglebetweenAUTO

andMANUALMODE.

Manual mode works only with the

ON-TIME switch in the 1, 5, or 10

position.

PuttheON-TIMEswitchinthe1,5,

or10minuteposition.

Mode: On-Time: Works: Day Night

Test

5Sec x x

Normal

1,5,10min. x

Manual

UntilDawn* x

ModelSH-5412

Motion Sensor

Light Control

MeetstheENERGYSTAR

guidelines

whenusedwith120WMaxbulbs.

2Shells

598-1158-04

INSTALLATION

Foreasyinstallation,selectanexistinglightoperated

byawallswitchforreplacement.

Forbestperformance,mountthextureabout8feet

(2.4m)abovetheground.NOTE:

Ifxtureismounted

higherthan8ft.(2.4m),aimingthesensordownwillreduce

coveragedistance.

Foreavemountonly:

❒Swingthesensorheadtowardstheclampscrew

joint.

If the sensor pops out of the ball joint, loosen the

clampscrewandpushthesensorbackintotheball

joint.Tightentheclampscrewwhendone.

❒Thenrotatethesensorheadclockwise180°sothe

controlsfacedown.

Controls

For under eave installation, the sensor head must

be rotatedasshowninthenexttwostepsforproper

operationandtoavoidtheriskofelectricalshock.

Controls

ClampScrew

Move ON-TIME Switch

to 1, 5, or 10 minutes

Mode Switching Summary

Flip light switch

off for one second

then back on*

MANUAL MODE

AUTO

TEST

* Ifyougetconfusedwhileswitchingmodes,turnthe

poweroffforoneminute,thenbackon.Afterthecali-

brationtimethecontrolwillbeintheAUTOmode.

Wall Mount Eave Mount

598-1158-04

❒ Removetheexistinglightxture.

❒ Installthemountingstrapasshownusingtwoscrews

thattyourjunctionbox.

❒ Theplastichangercanbeusedtoholdthexture

whilewiring.Thesmallendoftheplastichanger

canbethreadedthroughtheholeinthecenterof

thecoverplate.Thesmallendthengoesintoone

oftheslotsonthemountingstrap.

❒ Route the light control’s wires through the large

gasketholes.

❒  Twistthe junctionboxwiresandxturewirestogether

asshown.Securewithwireconnectors.

White to

White

Black to

Black

Junction box ground wire to

green ground screw on ﬁxture.

Gasket

Mounting

Strap

Mounting

Bolt

Rubber

Plug

WARNING: Turn power off at circuit breaker

or fuse.

Wire the Light Control

Mount the Light Control

❒ Alignthelightcontrolcoverplateandcoverplate

gasket.Securewiththemountingbolt.

❒ Alignthethreeslotsinthedecorativeshellwiththe

lampholderpins.Pushtheshellinandthentwist

clockwisetolock.Repeatforothershell.

LockNut

To avoid water damage and

electrical shock, keep lamp

holders30°belowhorizontal.

❒ Adjustthelampholdersbylooseningthelocknuts

butdonotrotatethelampholdersmorethan180°

from the factory setting. When screwing in the

oodlamps,donotovertighten.

Keeplampsatleast

1"(2.5cm)fromthe

sensor.Donotallow

the lamps to block

thelens.Lens

❒ Pushtherubberplugrmlyintoplace.

❒ Ifawetlocationjunctionboxwasnotused,caulk

the wall plate mounting surface with silicone

weathersealant.

ShellSlot

598-1158-04

TEST AND ADJUSTMENT

❒ Turn on the circuit breaker and light switch.

❒ Loosentheclampscrewinthe

sensor ball joint and gently

rotatethesensor.

❒ Walk through the coverage

area noting where you are

whenthelightsturnon(also,

theLEDwillashseveraltimes

whenmotionisdetected).Move

thesensorheadup,down,or

sidewaystochangethecover-

agearea.Keep the sensor at

least 1" (2.5 cm) away from

the lamps.

❒ AdjusttheRANGEasneeded.

RANGE set too high may

increasefalsetriggering.

❒ Secure the sensor head by

tightening the clamp screw.

Donotovertightenthescrew.

❒ SettheamountofTIMEyouwantthelightstostay

onaftermotionisdetected(1,5,or10minutes).

SPECIFICATIONS

Range............Upto70ft.(21m)[varieswith

surroundingtemperature].

SensingAngle......Upto180°

ElectricalLoad......Upto240WattMaximumTung-

sten[Upto120Wattmaximum

eachlampholder.]

PowerRequirements.120VAC,60Hz

OperatingModes....TEST, AUTO and MANUAL

MODE

TimeDelay ........1,5,10minutes

Range............Adjustable

HeathCoLLCreservestherighttodiscontinueprod-

uctsandtochangespecicationsatanytimewithout

incurringanyobligationtoincorporatenewfeatures

inproductspreviouslysold.

NOTE: Sensor has a 1

 minute warmup period

beforeitwilldetectmotion.Whenrstturned

on,wait1

minutes.

Bottom of Sensor

Avoid aiming the control at:

•Objects that change temperature rapidly, such as

heating vents and air conditioners.These heat

sourcescouldcausefalsetriggering.

•Areaswherepets or trafﬁcmaytriggerthecontrol.

•Nearby large, light-colored objectsreectinglight

maytriggertheshut-offfeature.Donotpointother

lightsatthesensor.

70ft.

(21m)

8ft.

(2.4m)

Clamp

Screw

Ball

Joint

Aim Sensor

Down for Short

Coverage

Aim Sensor

Higher for Long

Coverage

Least Sensitive Most Sensitive

WARNING: Risk of ﬁre. Do not aim the lamps

at a combustible surface within 3 ft. (1 m).

Maximum Range Maximum

Coverage Angle

RANGE

1051TEST

ON-TIME

MAXMIN

RANGEON-TIME

10 5 1 TEST

MINUTES

MIN MAX

NOTE:MeetstheENERGYSTAR

guidelineswhenused

with120WMaxbulbs.

❒ TurntheRANGEcontroltothemidposition(halfway

betweenMINandMAX)andtheON-TIMEcontrol

totheTESTposition.

Motion

180°

Sensor

NOTE:

Ifxtureismountedhigherthan8ft.(2.4m),aiming

thesensordownwillreducecoveragedistance.

Thedetectorislesssensitivetomotiondirectlytowardsit.

598-1158-04

SYMPTOM

Lights will not come

on.

Lights come on

in daylight.

Lights come on

for no apparent

reason.

POSSIBLE CAUSE

1. Lightswitchisturnedoff.

2. F loo d li gh t i s l oo se or

burnedout.

3. Fuseisblownorcircuitbreaker

isturnedoff.

4. Daylightturn-offisineffect(re-

check after dark).

5. Incorrectcircuitwiring,ifthisisa

newinstallation.

6. Re-aimthesensortocoverde-

siredarea.

1. Lightcontrolmaybeinstalledin

arelativelydarklocation.

2. Light control is in Test.

(Set control switch to an

ON-TIME position).

1. Light control may be sensing

smallanimalsorautomobiletraf-

c(re-aim sensor).

2. R a ng e  is  se t t oo hig h.

(Reduce Range).

SYMPTOM

Lights stay on

continuously.

Lights ﬂash on

and off.

POSSIBLE CAUSE

1. Aoodlampispositionedtoocloseto

thesensororpointedatnearbyobjects

thatcauseheattotriggerthesensor.

(Reposition the lamp away from the

sensor or nearby objects).

2.Lightcontrolispointedtowardaheat

sourcelikeanairvent,dryervent,or

brightly-painted heat-reective sur-

face.(Reposition sensor).

3. LightcontrolisinManualMode.(Switch

to Auto.)

1. Heatorlightfromthelampsmaybe

turning the light control on and off.

(Reposition the lamps away from the

sensor).

2. Heatbeingreectedfromotherobjects

maybeaffectingthesensor.(Reposi-

tion sensor).

3. LightcontrolisintheTestmodeand

warmingup.(Flashing is normal under

these conditions).

4. Lightmaybeleakingthroughtheood-

lampreectors.(Make sure the metal

lamp protectors are installed).

TROUBLESHOOTING GUIDE

TECHNICAL SERVICE

Please call 1-800-858-8501 (English speaking only) for assistance

before returning product to store.

Ifyouexperienceaproblem,followthisguide.YoumayalsowanttovisitourWebsiteat:www.hzsupport.com.

Iftheproblempersists,call*forassistanceat1-800-858-8501(Englishspeakingonly),7:30AMto4:30PMCST

(M-F).Youmayalsowrite*to:

HeathCo LLC

P.O.Box90045,BowlingGreen,KY42102-9045

ATTN:TechnicalService

*IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:ModelNumber,DateofPur-

chase,andPlaceofPurchase.

No Service Parts Available for this Product

TEN YEAR LIMITED WARRANTY

Thisisa“LimitedWarranty”whichgivesyouspeciclegalrights.Youmayalsohaveotherrightswhichvaryfromstatetostateor

provincetoprovince.

Foraperiodoftenyearsfromthedateofpurchase,anymalfunctioncausedbyfactorydefectivepartsorworkmanshipwillbecor-

rectedatnochargetoyou.

Not Covered -Repairservice,adjustmentandcalibrationduetomisuse,abuseornegligence,lightbulbs,batteries,andotherexpend-

ableitemsarenotcoveredbythiswarranty.Unauthorizedserviceormodicationoftheproductorofanyfurnishedcomponentwill

voidthiswarrantyinitsentirety.Thiswarrantydoesnotincludereimbursementforinconvenience,installation,setuptime,lossofuse,

unauthorizedservice,orreturnshippingcharges.

ThiswarrantycoversonlyHeathCoLLCassembledproductsandisnotextendedtootherequipmentandcomponentsthatacustomer

usesinconjunctionwithourproducts.

THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRANTIES,EXPRESSORIMPLIED,INCLUDINGANYWARRANTY,

REPRESENTATIONORCONDITIONOFMERCHANTABILITYORTHATTHEPRODUCTSAREFITFORANYPARTICULARPUR-

POSEORUSE,ANDSPECIFICALLYINLIEUOFALLSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGES.

REPAIRORREPLACEMENTSHALLBETHESOLEREMEDYOFTHECUSTOMERANDTHERESHALLBENOLIABILITYONTHE

PARTOFHEATHCOLLCFORANYSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGES,INCLUDINGBUTNOT

LIMITEDTOANYLOSSOFBUSINESSORPROFITS,WHETHERORNOTFORESEEABLE.Somestatesorprovincesdonotallow

theexclusionorlimitationofincidentalorconsequentialdamages,sotheabovelimitationorexclusionmaynotapplytoyou.

Please keep your dated sales receipt, it is required for all warranty requests.

Page is loading ...

Heath Zenith Motion Sensor Light Control SH-5412 User manual

Brand: Heath Zenith

Model: Motion Sensor Light Control SH-5412

Category: Work lights

Type: User manual

This manual is also suitable for

SH-5412

Download PDF

report

Heath Zenith Motion Sensor Light Control SH-5412 User manual

This manual is also suitable for

Heath Zenith Motion Sensor Light Control SH-5412 User manual

in other languages

Related papers

Other documents