Milwaukee V28 0779-20 User manual

Brand: Milwaukee

Model: V28 0779-20

Category: Cordless combi drills

Type: User manual

This manual is also suitable for

Cat. No.

No de cat.

Cat. No.

0779-20

0799-20

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE

MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL

DEL OPERADOR.

IMPACT WRENCH

CLÉ À PERCUSSION

LLAVE DE IMPACTO DE

2 3

1. Hold power tools by insulated grip-

ping surfaces when performing an

operation where the cutting tool may

contact hidden wiring or its own cord.

Contact with a “live” wire will make ex-

posed metal parts of the tool “live” and

shock the operator.

2. Maintain labels and nameplates. These

carry important information. If unread-

able or missing, contact a MILWAUKEE

service facility for a free replacement.

3. WARNING! Some dust created by power

sanding, sawing, grinding, drilling, and

other construction activities contains

chemicals known to cause cancer, birth

defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement

and other masonry products, and

• arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure

to these chemicals: work in a well ven-

tilated area, and work with approved

safety equipment, such as those dust

masks that are specially designed to

ﬁ lter out microscopic particles.

WORK AREA SAFETY

ELECTRICAL SAFETY

PERSONAL SAFETY

WARNING

READ ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or

serious injury. The term "power tool" in all of the warnings listed below refers to your

mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

GENERAL SAFETY RULES-FOR ALL BATTERY OPERATED TOOLS

1. Keep work area clean and well lit.

Cluttered or dark areas invite acci-

dents.

2. Do not operate power tools in ex-

plosive atmospheres, such as in the

presence of ﬂ ammable liquids, gases

or dust. Power tools create sparks which

may ignite the dust or fumes.

3. Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

4. Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power tools.

Unmodiﬁ ed plugs and matching outlets

will reduce risk of electric shock.

5. Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock

if your body is earthed or grounded.

6. Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric

shock.

7. Do not abuse the cord. Never use the

cord for carrying, pulling or unplug-

ging the power tool. Keep cord away

from heat, oil, sharp edges or moving

parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool out-

doors, use an extension cord suitable

for outdoor use. Use of a cord suitable

for outdoor use reduces the risk of elec-

tric shock.

9. Stay alert, watch what you are do-

ing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the inﬂ uence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may result

in serious personal injury.

10. Use safety equipment. Always wear

eye protection. Safety equipment such

as dust mask, non-skid safety shoes,

hard hat, or hearing protection used

for appropriate conditions will reduce

personal injuries.

11. Avoid accidental starting. Ensure the

switch is in the off-position before

plugging in. Carrying power tools with

your ﬁ nger on the switch or plugging in

power tools that have the switch on invites

accidents.

12. Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

13. Do not overreach. Keep proper foot-

ing and balance at all times. This

enables better control of the power tool

in unexpected situations.

14. Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

15. If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of these de-

vices can reduce dust-related hazards.

POWER TOOL USE AND CARE

16. Do not force the power tool. Use the

correct power tool for your applica-

tion. The correct power tool will do the

job better and safer at the rate for which

it was designed.

17. Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

18. Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preven-

tive safety measures reduce the risk of

starting the power tool accidentally.

19. Store idle power tools out of the

reach of children and do not allow

persons unfamiliar with the power

tool or these instructions to operate

the power tool. Power tools are danger-

ous in the hands of untrained users.

20. Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any

other condition that may affect the

power tool's operation. If damaged,

have the power tool repaired before

use. Many accidents are caused by

poorly maintained power tools.

21. Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

22. Use the power tool, accessories and

tool bits etc., in accordance with

these instructions and in the manner

intended for the particular type of

power tool, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

SERVICE

28. Have your power tool serviced by a

qualiﬁ ed repair person using only

identical replacement parts. This will

ensure that the safety of the power tool

is maintained.

23. Ensure the switch is in the off posi-

tion before inserting battery pack.

Inserting the battery pack into power

tools that have the switch on invites

accidents.

24. Recharge only with the charger speci-

ﬁ ed by the manufacturer. A charger

that is suitable for one type of battery

pack may create a risk of ﬁ re when used

with another battery pack.

BATTERY TOOL USE AND CARE

SPECIFIC SAFETY RULES

25. Use power tools only with speciﬁ cally

designated battery packs. Use of any

other battery packs may create a risk of

injury and ﬁ re.

26. When battery pack is not in use, keep

it away from other metal objects like

paper clips, coins, keys, nails, screws,

or other small metal objects that can

make a connection from one terminal

to another. Shorting the battery terminals

together may cause burns or a ﬁ re.

27. Under abusive conditions, liquid may

be ejected from the battery, avoid

contact. If contact accidentally oc-

curs, ﬂ ush with water. If liquid con-

tacts eyes, additionally seek medical

help. Liquid ejected from the battery

may cause irritation or burns.

4 5

FUNCTIONAL DESCRIPTION

1. 1/2" drive shank

2. Forward/Reverse switch

3. Trigger

4. Battery pack

5. Battery pack release buttons

6. Tool hanger

7. Tool hanger ring

8. 7/16" hex quick-change chuck

* Output rated at full speed

Impacts

Per

Minute

0 - 2450

Cat.

No.

0779-20

0799-20

Average

Torque

Output*

325 ft-lbs.*

Volts

Speciﬁ cations

Drive

Shank

1/2"

7/16" Hex

No Load

RPM

0 - 1450

Cat. No.

0779-20

0799-20

Quick Change Auger Bits

1-1/2"

Drilling Capacities

Selfeed Bits

2-9/16"

Symbology

Volts Direct Current

Impacts per Minute Under

Load (IPM)

Underwriters Laboratories, Inc.,

United States and Canada

Cat. No. 0799-20

Cat. No. 0779-20

TOOL ASSEMBLY

WARNING

Always lock trigger or remove battery

pack before changing or removing

accessories. Only use accessories

speciﬁ cally recommended for this

tool. Others may be hazardous.

Attaching and Removing the Tool Hanger

1. To attach, remove the two top gear case

screws (Fig. 1).

2. Place the ring through the tool hanger.

3. Position the tool hanger on the tool over

the two gear case screw holes.

4. Replace the two gear case screws.

Hand tighten the screws.

5. To remove, reverse the procedure.

Gear

case

screws

Ring

Fig. 1

Tool

hanger

Attaching and Removing Accessories

(Cat. No. 0779-20)

This impact wrench is intended only for use

with sockets designed for impact wrenches

and that have a 1/2" square drive. Other

sockets could shatter or break, causing

injury.

Fig. 2

Drive shank

Detent pin

WARNING

Use only sockets and other

accessories speciﬁ cally designed for

use on impact wrenches and drivers.

Other sockets and accessories might

shatter or break causing injury.

Removing Battery Pack from Tool

Push in the release buttons and pull the bat-

tery pack away from the tool.

Inserting Battery Pack into Tool

To insert the battery pack onto the tool, slide

the pack onto the body of the tool. Make sure

it latches securely into place.

1. For working in restricted spaces.

Insert the battery pack from the front

by pressing in the release buttons and

sliding battery pack into the body of the

tool. Insert the battery pack until clamp

engages.

2. For optimum weight distribution and

balance. Insert the battery pack from

the back by pressing in the release but-

tons and sliding the battery pack into the

body of the tool. Insert the battery pack

until clamp engages.

6 7

1. To attach a socket or other accessory,

align the hole in the accessory with

the detent pin on the drive shank.

Hold the detent pin in while pushing

the socket onto the drive shank. The

detent pin will snap into place in the hole

to secure the socket.

2. To remove the accessory, insert a nail

or other thin object into the hole in the

accessory and press the detent pin in.

Pull the accessory off the drive shank.

Attaching and Removing Accessories

(Cat. No. 0799-20, or other Impact Wrenches

using the Quick Change 1/2” Square Drive

to 7/16” Hex Adapter)

Cat. No. 0799-20 and accessory Cat. No.

48-66-0061 are intended for use with drill

bits and adapters with a 7/16” Hex Quick.

The Quick Change shank has a ball-retainer

groove. It is not intended for use with Hex

Shank Bit Extensions.

1. To attach an accessory, pull the chuck

collar forward and insert the accessory

shank. Release the collar. It may be

necessary to pull the bit out slightly to

engage the holding mechanism.

2. To remove the accessory, pull the chuck

collar forward and remove the acces-

sory. Release the collar.

Fig. 3

Ball retainer

groove

Open (Release)

Closed (Locked)

WARNING

To reduce the risk of injury, keep

hands away from the bit and all mov-

ing parts. Always wear safety goggles

or glasses with side shields.

OPERATION

Using the Forward/Reverse Switch

The forward/reverse switch may be set to

three positions: forward, reverse and lock.

Due to a lockout mechanism, the forward/

reverse switch can only be adjusted when

the trigger is not depressed. Always al-

low the motor to come to a complete stop

before using the forward/reverse switch.

1. For forward (clockwise) rotation,

push the forward/reverse switch

in the direction shown. Check the

direction of rotation before use.

2. For reverse (counterclockwise)

rotation, push the forward/reverse

switch in the direction shown. Check the

direction of rotation before use.

3. To lock the trigger, push the forward/

reverse switch to the center position.

The trigger will not work when the

forward/reverse switch is in the

locked position. Always lock the

trigger or remove the battery pack

before performing maintenance, chang-

ing accessories, storing the tool and any

time the tool is not in use.

WARNING

To reduce the risk of injury, only

grasp tool by handle and red

insulated surfaces (Fig. 5). Do

not hold gray gear case when

impacting or drilling.

WARNING

To reduce the risk of explosion,

electric shock and property

damage, always check the work area

for hidden pipes and wires before

drilling.

Starting, Stopping and Controlling

Speed

This impact wrench may be operated at any

speed from 0 to full speed.

1. To start the tool, grasp the handle ﬁ rmly

and pull the trigger.

2. To vary the speed, increase or

decrease the pressure on the trigger.

The further the trigger is pulled, the

greater the speed.

3. To stop the tool, release the trigger.

Fig. 4

Reverse

Forward

Forward/

Reverse

switch

Fig. 5

Impacting Techniques

The longer a bolt, screw, or nut is impacted,

the tighter it will become. To help prevent

damaging the fasteners or workpieces,

avoid excessive impacting. Be particularly

careful when impacting smaller fasteners

because they require less impacting to reach

optimum torque.

Practice with various fasteners, noting the

length of time required to reach the desired

torque. Check the tightness with a hand-

torque wrench. If the fasteners are too tight,

reduce the impacting time. If they are not

tight enough, increase the impacting time.

Impacting for two seconds is generally

sufﬁ cient for a 3/8" bolt and one second

for a 5/16" bolt. However, oil, dirt, rust or

other matter on the threads or under the

head of the fastener affects the degree of

tightness.

The torque required to loosen a fastener

averages 75% to 80% of the tightening

torque, depending on the condition of the

contacting surfaces. However, if rust or

corrosion causes seizing, more torque may

be required.

On light gasket jobs, run each fastener down

to a relatively light torque and use a hand

torque wrench for ﬁ nal tightening.

Electric Brake

The electric brake engages when the

trigger is released, causing the socket

to stop and allowing you to proceed with

your work. Generally, the socket stops

within two seconds. However, there may

be a delay between the time you release

the trigger and when the brake engages.

Occasionally the brake may miss completely.

If the brake misses frequently, the impact

wrench needs servicing by an authorized

MILWAUKEE service facility.

8 9

Cleaning

Clean dust and debris from charger and tool

vents. Keep tool handles clean, dry and free

of oil or grease. Use only mild soap and a

damp cloth to clean the tool, battery pack

and charger since certain cleaning agents

and solvents are harmful to plastics and other

insulated parts. Some of these include gaso-

line, turpentine, lacquer thinner, paint thinner,

chlorinated cleaning solvents, ammonia and

household detergents containing ammonia.

Never use ﬂ ammable or combustible sol-

vents around tools.

WARNING

To reduce the risk of injury,

always unplug the charger and

remove the battery pack from

the charger or tool before

performing any maintenance.

Never disassemble the tool,

battery pack or charger. Contact a

MILWAUKEE service facility for ALL

repairs.

Keep your tool, battery pack and char-

ger in good repair by adopting a regular

maintenance program. After six months

to one year, depending on use, return the

tool, battery pack and charger to a

MILWAUKEE service facility for:

• Lubrication

• Mechanical inspection and cleaning

(gears, spindles, bearings, housing,

etc.)

• Electrical inspection (battery pack,

charger, motor)

• Testing to assure proper mechanical and

electrical operation

Maintaining Tool

If the tool does not start or operate at full pow-

er with a fully charged battery pack, clean

the contacts on the battery pack. If the tool

still does not work properly, return the tool,

charger and battery pack, to a MILWAUKEE

service facility for repairs.

MAINTENANCE

WARNING

To reduce the risk of personal injury

and damage, never immerse your

tool, battery pack or charger in liquid

or allow a liquid to ﬂ ow inside them.

Repairs

For repairs, return the tool, battery pack and

charger to the nearest service center listed on

the back cover of this operator's manual.

ACCESSORIES

Always remove battery pack before

changing or removing accessories.

Only use accessories speciﬁ cally

recommended for this tool. Others

may be hazardous.

WARNING

For a complete listing of accessories refer to

your MILWAUKEE Electric Tool catalog or go

on-line to www.milwaukeetool.com. To obtain

a catalog, contact your local distributor or a

service center listed on the back cover of this

operator’s manual.

FIVE YEAR TOOL LIMITED WARRANTY

Every MILWAUKEE electric power tool (including battery charger) is warranted to the original

purchaser only to be free from defects in material and workmanship. Subject to certain excep-

tions, MILWAUKEE will repair or replace any part on a electric power tool which, after examina-

tion, is determined by MILWAUKEE to be defective in material or workmanship for a period of

ﬁ ve (5) years* after the date of purchase. Return the electric power tool and a copy of proof

of purchase to a MILWAUKEE factory Service/Sales Support Branch location or MILWAUKEE

Authorized Service Station, freight prepaid and insured, are requested for this warranty to be

effective. This warranty does not apply to damage that MILWAUKEE determines to be from

repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse,

alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

* The warranty period for Hoists (lever, hand chain, & electric chain hoists), all Ni-CD battery

packs, Work Lights (cordless ﬂ ashlights), Job Site Radios, and Trade Titan™ Industrial Work

Carts is one (1) year from the date of purchase. *The warranty period for Li-Ion battery packs

that do not contain V™-technology – 4.0 volts through 18.0 volts - is two (2) years from the

date of purchase.

*There is a separate warranty for V™-technology Li-Ion Battery Packs V™18 volts and above

that accompany V™-technology cordless power tools:

*Every MILWAUKEE V™-technology Li-Ion Battery Pack 18 volts or above is covered by an

initial 1000 Charges/2 Years free replacement warranty. This means that for the earlier of

the ﬁ rst 1000 charges or two (2) years from the date of purchase/ﬁ rst charge, a replacement

battery will be provided to the customer for any defective battery free of charge. Thereafter,

customers will also receive an additional warranty on a pro rata basis up to the earlier of the

ﬁ rst 2000 charges or ﬁ ve (5) Years from the date of purchase/ﬁ rst charge. This means that

every customer gets an additional 1000 charges or three (3) years of pro rata warranty on

the V™-technology Li-Ion Battery Pack 18 volts or above depending upon the amount of use.

During this additional warranty period, the customer pays for only the useable service received

over and above the ﬁ rst 1000 Charges/2 years, based on the date of ﬁ rst charge and number

of charges found on the battery pack via Milwaukee’s V™-technology Service Reader.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE

product. However, proof of purchase in the form of a sales receipt or other information deemed

sufﬁ cient by MILWAUKEE, is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DE-

SCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF

EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU

SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LI-

ABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES,

OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED

TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY

PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OR CON-

DITIONS, WRITTEN OR ORAL, EXPRESSED OR IMPLIED. WITHOUT LIMITING THE

GENERALITY OF THE FOREGOING, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE, AND ALL

OTHER WARRANTIES.

This warranty applies to product sold in the U.S.A., Canada and Mexico only.

Page is loading ...

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 West Lisbon Road • Brookﬁ eld, Wisconsin, U.S.A. 53005

58-14-0779d5 05/07 Printed in USA

UNITED STATES - MILWAUKEE Service

MILWAUKEE prides itself in producing a premium quality product that is

NOTHING BUT HEAVY DUTY

. Your satisfaction with our products is very important to us!

If you encounter any problems with the operation of this tool, or you would like to

locate the factory Service/Sales Support Branch or authorized service station

nearest you, please call...

1-800-SAWDUST

(1.800.729.3878)

NATIONWIDE TOLL FREE

Monday-Friday • 8:00 AM - 4:30 PM • Central Time

or visit our website at

www.milwaukeetool.com

For service information, use the 'Service Center Search' icon found in the 'Parts & Service' section.

Additionally, we have a nationwide network of authorized Distributors ready to assist you with your

tool and accessory needs. Check your “Yellow Pages” phone directory under “Tools-Electric” for

the names & addresses of those nearest you or see the 'Where To Buy' section of our website.

Corporate After Sales Service - Technical Support

Brookﬁ eld, Wisconsin USA

•Technical Questions •Service/Repair Questions •Warranty

1-800-SAWDUST

(1.800.729.3878) fax: 1.800.638.9582

email: [email protected]

Monday-Friday • 8:00 AM - 4:30 PM • Central Time

Canada - Service MILWAUKEE

Milwaukee Electric Tool, S.A. de C.V.

Blvd. Abraham Lincoln no. 13

Colonia Los Reyes Zona Industrial

Tlalnepantla, Edo. México C.P. 54073

Tel. (55) 5565-1414 Fax: (55) 5565-6874

Adicionalmente, tenemos una red nacional de

distribuidores autorizados listos para ayudarle

con su herramienta y sus accesorios. Por

favor, llame al (55) 5565-1414 para obtener los

nombres y direcciones de los más cercanos a

usted, o consulte la sección ‘Where to buy’

(Dónde comprar) de nuestro sitio web en

www.milwaukeetool.com

MILWAUKEE est ﬁ er de proposer un produit

de première qualité NOTHING BUT HEAVY DUTY

Votre satisfaction est ce qui compte le plus!

En cas de problèmes d’utilisation de l’outil ou

pour localiser le centre de service/ventes ou le

centre d’entretien le plus proche, appelez le...

416.439.4181

fax: 416.439.6210

Milwaukee Electric Tool (Canada) Ltd

755 Progress Avenue

Scarborough, Ontario M1H 2W7

Notre réseau national de distributeurs agréés

se tient à votre disposition pour fournir l’aide

technique, l’outillage et les accessoires

nécessaires. Composez le 416.439.4181 pour

obtenir les noms et adresses des revendeurs

les plus proches ou bien consultez la section

«Où acheter» sur notre site web à l’adresse

www.milwaukeetool.com

MEXICO - Soporte de Servicio

MILWAUKEE

Milwaukee V28 0779-20 User manual

Brand: Milwaukee

Model: V28 0779-20

Category: Cordless combi drills

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Milwaukee V28 0779-20 Manuel utilisateur
español: Milwaukee V28 0779-20 Manual de usuario

Milwaukee V28 0779-20 User manual

This manual is also suitable for

Milwaukee V28 0779-20 User manual

in other languages

Related papers

Other documents