Metabo GE710 Plus User manual

Brand: Metabo

Model: GE710 Plus

Category: Power tools

Type: User manual

This manual is also suitable for

www.metabo.com Made in Germany

en Operating Instructions 4

fr Mode d'emploi 11

es Instrucciones de manejo 19

GA 18 LTX

GA 18 LTX G

GE 710 Compact

GE 710 Plus

GE 950 G Plus

Page is loading ...

ENGLISHen

Operating Instructions

The straight grinders are designed...

- ... for fine grinding work with abrasive points on

metal.

- ... for fine cutting work with small cutting wheels on

metal.

- ... for routing with end mill cutters on non-ferrous

metals, plastics, hardwood, etc.

- ...for working with paint and round wire brushes

- ...for working with polishing bobs

- ...for working with felt polishing tools

- ...for working with lamellar grinding wheels

The machine is not suitable for working with

polishing bells.

The user bears sole responsibility for any damage

caused by improper use.

Generally accepted accident prevention regula-

tions and the enclosed safety information must be

observed.

For your own protection and for the

protection of your electrical tool, pay

attention to all parts of the text that are

marked with this symbol!

WARNING – Reading the operating instruc-

tions will reduce the risk of injury.

Pass on your electrical tool only together with these

documents.

General Power Tool Safety Warnings

WARNING – Read all safety warnings and

all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire

and/or serious injury.

Save all warnings and instructions for future

reference! The term "power tool" in the warnings

refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

2.1 Work area safety

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of flam-

mable liquids, gases or dust. Power tools create

sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2.2 Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching out-

lets will reduce risk of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased

risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location is

unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

2.3 Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery

or long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

2.4 Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

1. Specified conditions of use

2. General safety instructions

ENGLISH en

power tool will do the job better and safer at the rate

for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and must

be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage of

parts and any other condition that may affect

the power tool's operation. If damaged, have

the power tool repaired before use. Many acci-

dents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

2.5 Battery tool use and care

a) Recharge only with the charger specified by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire

when used with another battery pack.

b) Use power tools only with specifically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irri-

tation or burns.

2.6 Service

a) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

3.1 Safety Warnings Common for Grinding,

Sanding, Wire Brushing, Polishing or

Abrasive Cutting-Off Operations:

Use

a) This power tool is intended to function as a

grinder, sander, wire brush, polisher or cut-off

tool. Read all

safety warnings,

instructions,

illustrations and specifications provided with

this power tool. Failure to follow all the instructions

may result in electric shock, fire and/or serious

injury.

b) Do not use any accessories that are not

specifically designed and recommended by the

tool manufacturer. Just because the accessory

can be attached to your power tool, it does not

assure safe operation.

c) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

d) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized acces-

sories cannot be adequately guarded or controlled.

e) The arbour size of wheels, flanges, backing

pads or any other accessory must properly fit

the spindle of the power tool. Accessories with

arbour holes that do not match the mounting hard-

ware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

f) Do not use damaged accessories. Before

each use, inspect accessories such as abra-

sive wheels for chips and cracks, backing pad

for cracks, tear or excess wear, wire brush for

loose or cracked wires. If a power tool or

accessory is dropped, check it for damage or

install an undamaged accessory. After

inspecting and installing an accessory, posi-

tion yourself and bystanders away from the

plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute. Damaged accessories will normally break

apart during this test time.

g) Wear personal protective equipment.

Depending on application, use a face shield,

safety goggles or safety glasses. As appro-

priate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments.

The eye protection must be capable of stopping

flying debris generated by various operations. The

dust mask or respirator must be capable of filtering

particles generated by your operation. Prolonged

exposure to high intensity noise may cause hearing

loss.

h) Keep bystanders a safe distance away from

the work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

3. Special Safety Instructions

ENGLISHen

i) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. A cutting acces-

sory that comes in contact with a "live" wire may

render exposed metal parts of the power tool "live"

and give the operator an electric shock.

j) Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into

the spinning accessory.

k) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grip the surface and pull

the power tool out of your control.

l) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

m) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

n) Do not operate the power tool near flam-

mable materials. Sparks could ignite these mate-

rials.

o) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution or shock.

3.2 Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or any

other accessory. Pinching or snagging causes rapid

stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite to the accessory’s rotation at

the point of jamming.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of

the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these condi-

tions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use the auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or kick-

back forces, if proper precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in a direction opposite to the

wheel’s movement at the point of snagging.

d) Use special care when working around

corners, sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp edges or

bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades create

frequent kickback and loss of control.

3.3 Safety Warnings Specific for Grinding

and Abrasive Cutting-Off Operations:

a) Use only wheel types that are recommended

for your power tool and the specific guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot be

adequately guarded and are unsafe.

b) Wheels must be used only for recommended

applications. For example: do not grind with

the side of the cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them to

shatter.

c) Always use undamaged wheel flanges that

are the correct size and shape for your selected

wheel. Proper wheel flanges support the wheel

thus reducing the possibility of wheel breakage.

Flanges for cut-off wheels may be different from

grinding wheel flanges.

d) Do not use worn down wheels from larger

power tools. Wheels intended for larger power

tools are not suitable for the higher speed of a

smaller tool and may burst.

3.4 Additional Safety Warnings Specific for

Abrasive Cutting-Off Operations:

a) Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to make

excessively deep cuts. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility

of kickback or wheel breakage.

b) Do not position your body in line with and

behind the rotating wheel. When the wheel, at the

point of operation, is moving away from your body,

the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) If the wheel jams or if you interrupt a cut for

any reason, switch off the power tool and hold

the power tool motionless until the wheel

comes to a complete stop. Never attempt to

remove the cut-off wheel from the cut while the

wheel is in motion, otherwise kickback may

occur. Investigate and take corrective action to

eliminate the cause of the wheel jam.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully reenter the cut. The wheel may jam,

walk up or kickback if the power tool is restarted in

the workpiece.

e) Support panels or any oversized workpiece

to minimise the risk of wheel pinching and kick-

ENGLISH en

back. Large workpieces tend to sag under their own

weight. Supports must be placed under the work-

piece near the line of cut and near the edge of the

workpiece on both sides of the wheel.

f) Use extra caution when making a "pocket

cut" into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, elec-

trical wiring or objects that can cause kickback.

3.5 Safety Warnings Specific for Sanding

Operations:

a) Do not use oversized sanding disc paper.

Follow manufacturer's recommendations when

selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a

laceration hazard and may cause snagging, tearing

of the disc or kickback.

3.6 Safety Warnings Specific for Polishing

Operations:

a) Loose parts on the polishing guard, espe-

cially the fastening cords, are not permitted.

Tuck away or shorten the fastening cords.

Loose, spinning fastening cords may make contact

with your fingers or become caught in the work-

piece.

3.7 Safety Warnings Specific for Wire Brush-

ing Operations:

a) Be aware that wire bristles are lost by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work load

and centrifugal forces.

3.8 Additional Safety Instructions

WARNING – Always wear protective

goggles.

Use elastic cushioning layers if they have been

supplied with the abrasive and if required.

Observe the specifications of the tool or accessory

manufacturer! Protect the discs from grease or

impacts!

Abrasives must be stored and handled with care in

accordance with the manufacturer's instructions.

Never use parting grinder discs for roughing work.

Do not apply pressure to the side of parting grinder

discs.

The workpiece must lay flat and be secured against

slipping, e.g. using clamps. Large workpieces must

be supported adequately.

Engage the spindle locking button (4) only when the

motor is inoperative. (GA 18 LTX, GE 710 Plus,

GA 18 LTX G, GE 950 G Plus)

Keep hands away from the rotating tool! Remove

chips and similar material only when the machine is

at a standstill.

Prior to use, ensure that the coated abrasive is

properly fitted and secured. Run the tool in idling for

60 seconds in a safe position and bring to a stand-

still immediately if there are significant vibrations or

if other deficiencies are determined. If such a situa-

tion occurs, check the machine to determine the

cause.

Ensure that sparks produced during work do not

constitute a risk to the user or other personnel and

are not able to ignite inflammable substances.

Endangered areas must be protected with flame-

resistant covers. Make sure that fire-risk areas are

always provided with suitable fire extinguishers.

Dust from material such as paint containing lead,

some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may

cause allergic reactions and/or respiratory diseases

to the operator or bystanders.

Certain kinds of dust are classified as carcinogenic

such as oak and beech dust especially in

conjunction with additives for wood conditioning

(chromate, wood preservative). Material containing

asbestos must only be treated by specialists.

- Where the use of a dust extraction device is

possible it shall be used.

- The work place must be well ventilated.

- The use of a dust mask of filter class P2 is recom-

mended.

Follow national requirements for the materials you

want to work with.

Materials that generate dusts or vapours that may

be harmful to health (e.g. asbestos) must not be

processed.

When working in dusty conditions, ensure that

ventilation openings are not blocked. If it becomes

necessary to remove dust, first disconnect the

power tool from the mains supply (use non-metallic

objects) and avoid damaging internal components.

Damaged, eccentric or vibrating tools must not be

used.

In the interests of safety, ensure that the rubber

sleeve (3) or additional handle is fitted while

working (5).

3.9 Special safety instructions for mains

powered machines:

Pull the plug out of the plug socket before any

adjustments, conversions or servicing are

performed.

During machining, of metals in

particular, conductive dust can form

deposits inside the machine. This can lead to the

transfer of electrical energy onto the machine

housing. This can mean a temporary danger of

electric shocks. This is why it is necessary when the

machine is running to blow compressed air through

the rear ventilation slots of the machine regularly,

frequently and thoroughly. Here, the machine must

be held firmly.

We recommend using a stationary extractor system

and connecting a residual current circuit-breaker

(RCD) upstream. When the machine is shut down

via the FI circuit-breaker, it must be checked and

ENGLISHen

cleaned. For information on cleaning the motor, see

chapter 7. Cleaning.

3.10 Special safety instructions for cordless

machines:

Remove the battery pack from the machine before

any adjustments, conversions or servicing are

performed.

Protect battery packs from water and mois-

ture!

Do not expose battery packs to naked flame!

Do not use faulty or deformed battery packs!

Do not open battery packs!

Do not touch or short-circuit battery packs!

Slightly acidic, flammable fluid may leak from

defective li-ion battery packs!

If battery fluid leaks out and comes into

contact with your skin, rinse immediately

with plenty of water. If battery fluid leaks out

and comes into contact with your eyes, wash them

with clean water and seek medical attention imme-

diately.

SYMBOLS ON THE TOOL:

...........Class II Construction

V...............volts

A...............amperes

Hz.............hertz

W..............watts

..............alternating current

.......... direct current

rpm ......... revolutions per minute

.../min ..... revolutions per minute

n ............. rated speed

See page 2.

1 Collet chuck

2 Collet chuck nut

3 Rubber sleeve *

4 Spindle locking button*

5 Additional handle *

6 Sliding switch

7 Main handle

8 Setting wheel for speed adjustment *

9 Dust filter

10 Electronic signal indicator*

11 B

attery pack release button *

12 Capacity indicator button *

13 Capacity and signal indicator *

14 Battery pack*

equipment-specific

5.1 For mains powered machines only

Before plugging in the device, check to see

that the rated mains voltage and mains

frequency, as specified on the rating label, match

your power supply.

5.2 For cordless machines only

Dust filter

Always fit the dust filter if the surroundings are

heavily polluted (9).

The machine heats up faster when the dust

filter is fitted (9). It is protected by the elec-

tronics system from overheating (see chapter8.).

To fit:

See page 2, illustration A.

Fit the dust filter (9) as shown.

To remove:

Holding the dust filter (9) by the upper

edges, raise it slightly and then pull it downwards

and remove.

Rotating battery pack

See illustration B on page 2.

The rear section of the machine can be rotated 270°

in three stages, thus allowing the machine's shape

to be adapted to the working conditions. Only

operate the machine when it is in an engaged posi-

tion.

Battery pack

Charge the battery pack before use (14).

If performance diminishes, recharge the battery

pack.

The ideal storage temperature is between 10°C and

30°C.

"Li-Power" li-ion battery packs have a capacity and

signal indicator: (13)

- Press the button (12), the LEDs indicate the

charge level.

- If one LED is flashing, the battery pack is almost

flat and must be recharged.

Removing and inserting the battery pack

To remove:

Press the battery pack release button

(11) and pull the battery pack (14) downwards

To fit:

Slide in the battery pack (14) until it engages.

6.1 Collet chucks

The tool's shank diameter must correspond

exactly to the collet bore of the collet chuck (1)!

Various collet chucks are available for different

shank diameters. See Accessories section.

6.2 Fitting the tools

Pull the mains plug from the socket.

Only use tools that are suited to the no-load

speed of your machine. See Technical Speci-

fications.

4. Overview

5. Initial Operation

6. Use

ENGLISH en

The tool's shank diameter must correspond

exactly to the collet bore of the collet chuck (1)!

For abrasive points, you must never exceed

the maximum open shank length specified by

the manufacturer l

Insert the tool (with the full length of the shank) in the

collet chuck (1).

Bring the spindle to a standstill. (For the

GE 710 Compact, use the 13-mm spanner provided

for this purpose. For the GA 18 LTX, GE 710 Plus,

GA 18 LTX G and GE 950 G Plus, press the spindle

locking button (4)).

Using the 19-mm spanner, tighten the collet chuck

nut (2).

If there is no tool inserted in the collet chuck,

you can tighten the collet chuck manually

rather than with the spanner.

6.3 Switching On and Off

Switch on first, then guide the

accessory

towards the workpiece.

Avoid inadvertent starts: always switch the

tool off when the plug is removed from the

mains socket or if there has been a power cut.

In continuous operation, the machine

continues running if it is forced out of your

hands. You must therefore always hold the machine

with both hands using the handles provided (3), (5),

(7), stand in a safe position and concentrate while

working.

Switching on: Push the slide switch (6) forward.

For continuous activation, now tilt downwards until

it engages.

Switching off: Press the rear end of the slide

switch (6) and release.

6.4 Adjusting speed (mains powered

machines only)

The speed can be preset using the setting wheel (8)

and is infinitely variable. For a list of speeds, see the

table on page 3.

6.5 Working instructions

Grinding, sanding, polishing or using wire

brushes: Press down the machine evenly and

move it from side to side over the surface.

Routing: Press down the machine evenly.

Separating:

Always work against the run of the disc

(see illustration). Otherwise there is

the danger of the machine kicking

back from the cut out of control. Guide

the machine evenly at a speed suit-

able for the material being processed. Do not tilt,

apply excessive force or sway from side to side.

7.1 Motor cleaning

To clean the motor, apply jets of compressed air

through the rear ventilation slots of the machine

regularly, frequently and thoroughly. Here, the

machine must be held firmly.

8.1 Mains powered machines:

- Overload protection: There is a MAJOR

reduction in load speed. The motor temperature

is too high! Allow the machine to run at idle speed

until it has cooled down.

- Overload protection: There is a SLIGHT

reduction in load speed. The machine is over-

loaded. Reduce the load before continuing to

work.

- Metabo S-automatic safety shutdown: The

machine was SWITCHED OFF automatically. If

the slew rate of the current is too high (for

example, if the machine suddenly seizes or kick-

back occurs), the machine switches off. Switch off

the machine at the slide switch (6). Switch it on

again and continue to work as normal. Try to

prevent the machine from seizing. See section

3.2.

- Restart protection: The machine does not

start. The restart protection is active. If the mains

plug is inserted with the machine switched on, or if

the current supply is restored following an inter-

ruption, the machine does not start up. Switch the

machine off and on again.

8.2 Cordless machines:

- The electronic signal display (10) lights up

and the load speed decreases. The tempera-

ture is too high! Run the machine in idling until the

electronics signal indicator switches off.

- The electronic signal display (10) flashes and

the machine does not start. The restart protec-

tion is active. The machine will not start if the

battery pack is inserted while the machine is on.

Switch the machine off and on again.

Use only genuine Metabo accessories.

Use only accessories which fulfil the requirements

and specifications listed in these operating instruc-

tions.

Fit accessories securely. Secure the machine if it is

operated in a bracket. Loss of control can cause

personal injury.

A Collets (including nut)

dia.

3 mm = 6.31947

dia.

1/8“ = 6.31948

dia.

6 mm = 6.31945

dia.

1/4“ = 6.31949

dia.

8 mm = 6.31946

B Clamping frame 6.27354 for clamping during

work with flexible shafts (tighten clamping

7. Cleaning

8. Troubleshooting

9. Accessories

ENGLISHen

screw), including:

C Clamping bracket 6.27107 for safe securing to

the work bench (tighten clamping screw).

D Battery chargers: ASC 15, ASC 30 and others.

E Battery packs: 4.0 Ah (6.25527); 3.0 Ah (6.25455)

For a complete range of accessories, see

www.metabo.com or the catalogue.

Repairs to electrical tools must be carried out

by qualified electricians ONLY!

If you have Metabo electrical tools that require

repairs, please contact your Metabo service centre.

For addresses see www.metabo.com.

You can download spare parts lists from

www.metabo.com.

Observe national regulations on environmentally

compatible disposal and on the recycling of disused

machines, packaging and accessories.

Special instructions for cordless machines:

Battery packs must not be disposed of with regular

waste. Return faulty or used battery packs to your

Metabo dealer!

Do not allow battery packs to come into contact with

water!

Before disposal, discharge the battery pack in the

power tool. Prevent the contacts from short-

circuiting (e. g. by protecting them with adhesive

tape).

Explanation of details on page 3. Subject to

changes serving technical progress.

U =Voltage of battery pack

S =Spindle lock for easy tool changes

n =No-load speed (maximum speed)

=On-load speed

120 V

= Current at 120 V

=Nominal power input

=Power output

max

=maximum grinding wheel diameter

d = Collet bore of the collet chuck

m =Weight with smallest battery pack/weight

without cord

The technical specifications quoted are subject to

tolerances (in compliance with the relevant valid

standards).

Wear ear protectors!

Electromagnetic disturbances:

In individual cases, the speed may fluctuate tempo-

rarily if the machine is exposed to extreme external

electromagnetic disturbances or the electronic

restart protection may respond. In this case, switch

the machine off and on again.

10. Repairs

11. Environmental Protection

12. Technical Specifications

Page is loading ...

Metabowerke GmbH,

72622 Nürtingen, Germany

www.metabo.com

170 27 1310 - 1212

Metabo GE710 Plus User manual

Brand: Metabo

Model: GE710 Plus

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Metabo GE710 Plus Manuel utilisateur
español: Metabo GE710 Plus Manual de usuario

Metabo GE710 Plus User manual

This manual is also suitable for

Metabo GE710 Plus User manual

in other languages

Related papers

Other documents