Huion KAMVAS PRO 12 User manual

GT-116

KAMVAS Pro 12

2

26

46

66

86

106

User Manual

Benutzerhandbuch

Manuel d' utilisateur

ユーザーマニュアル

Manuale d' uso

Manual de Usuario

GT-116

2

EN

【Click on the directory to get to the page】

Contents

1 / Precautions ...............................................................................................................3

2 / Product Overview ....................................................................................................4

2.1 Display Introduction ................................................................................................................... 4

2.2 Product and Accessories ...........................................................................................................4

2.3 Setting Display ..............................................................................................................................6

2.4 Install Driver .................................................................................................................................7

3 / Pen Basic Operation ................................................................................................9

3.1 Hold the pen .................................................................................................................................9

3.2 Position the cursor ...................................................................................................................... 9

3.3 Click .................................................................................................................................................. 10

3.4 Move ................................................................................................................................................10

3.5 Use the side buttons ..................................................................................................................10

3.6 Pen Nib Replacement .................................................................................................................11

4 / Using the Display .....................................................................................................12

4.1 Power Button .................................................................................................................................12

4.2 Press Keys .......................................................................................................................................12

4.3 Touch Bar ........................................................................................................................................12

4.4 OSD Function ................................................................................................................................12

5 / Function Setting .......................................................................................................13

5.1 Working Area Setting .................................................................................................................13

5.2 Press Keys Function Setting .....................................................................................................14

5.3 Pen Buttons Function Setting ..................................................................................................16

5.4 Enable the Windows Ink Feature............................................................................................ 16

5.5 Pressure Sensitivity Setting ......................................................................................................17

5.6 Pen Pressure Testing ...................................................................................................................18

5.7 Enable the Windows Ink Feature............................................................................................ 18

6 / Specifications ...........................................................................................................19

7 / Trouble Shooting .....................................................................................................20

8 / After-service Contact ..............................................................................................23

GT-116

3

EN

【Please read this manual carefully before using, and keep it well for future reference.】

/ Precautions

1

--Before cleaning the display, please unplug the USB cable and wipe with a soft damp

cloth, do not use any kind of detergents.

--Please don't place the display near water sources such as bathtub, washbasin, sinks,

washing machine, damp basement, swimming pool, etc.

--Do not place the display on where is unstable or a height for children reaching easily in

order to avoid danger.

--Do not place the display and digital pen close to the magnetic field.

--The grooves and holes on the back case is designed for ventilation to prevent the

monitor from overheating. Please don't place the display on beds, sofas, carpets or in

embedded device.

--Only power supplies shown on the nameplate can be used for the display. If you have

questions about the power supply which you are using, please consult the distributor of

your display.

--To protect your display, please switch off the power when it is not in use. During

blackouts or not using for long time, please unplug the display from the socket.

--Make sure no foreign bodies get inside the monitor through grooves and prevent liquid

from splashing on the display as to prevent short-circuit or fire.

--If the display has a breakdown, do not open the main case and try to repair it by yourself.

Please ask for a service for proper repair and maintenance.

--When the following situations occur, please unplug the power adapter and you may need

a service for full repair and maintenance:

A. The power wire or plug is damaged or worn out;

B. There is liquid splashed inside of the display;

C. The display has fallen or the LCD is broken;

D. When obvious abnormalities occur to the display.

--While getting the components replaced, you are supposed to guarantee that the

repairman is using the substitute components specified by the manufacturer. Unauthorized

component replacement might cause fire, electric shocks or other dangers.

GT-116

4

EN

/ Product Overview

2

2.1 Display Introduction

Thanks for choosing HUION® KAMVAS® Pro 12 creative display. This is a new

generation of desktop-level professional drawing display, which can greatly improve

your work efficiency of painting and creation, and full of fun. You can freely paint

and write, depicting different lines and colors, just as the pen writes on the paper,

which brings you a real shock experience.

To give you a better understanding and using of your display, please read this user

manual carefully. The user manual only shows the information under Windows,

unless otherwise specified, this information applies to both Windows and Macintosh

systems.

2.2 Product and Accessories

GT-116

5

EN

Battery-free pen Replacement Nibs

(inside the pen holder) Pen Holder

Quick Start GuideStand

Power Adapter

Cleaning Cloth

Pen Nib Clip

(inside the pen holder)

2.2.1 Accessories

3-in-1 Cable

2.2.2 Adjustable Stand

We designed this ergonomic adjustable stand specially for your KAMVAS display,

you can adjust the angle of the display according to your usage habit, and make

you feel more comfortable when painting and creating.

GT-116

6

EN

2.2.3 3-in-1 Cable

①

②

③

④

① USB ② HDMI ③ Power ④ Type-C

2.2.4 Plug

Please choose the right plug according to your country or region, and assemble it

to the power adapter. (It may not come with all the plugs)

GT-116

7

EN

2.3 Setting Up Display

[1] Connect your PC and the display with 3-in-1 cable.

[2] Plug the power adapter into the cable power connector and turn it 90° to

ensure that the plug does not come off and connect the power adapter to the

power source.

[3] Turn on computer and switch on the display, the LED indicator will show the

current status: Green means working normal, Orange means no signal.

2.4 Install Driver

2.4.1 OS Support

Windows 7 or later, macOS 10.12 or later.

2.4.2 Install Driver

Please download the driver from our website: www.huion.com/download

After finishing installation, you can find the driver icon " " in the system tray area,

which means the driver was installed successfully; when you connect the display

to computer, the icon will change to color " ", which means the driver has already

recognized the display and you can start using it now.

Notes:

[1] Before installing, you need to uninstall other driver of similar products, including

the old driver of this product.

[2] Before installing, please close all graphics software and anti-virus software to

avoid unnecessary mistake.

GT-116

8

EN

2.4.3 Driver Page

After the download is successful, double-click to open the driver, connect the

display to your computer with attached cable.

When the connection is complete, watch for a prompt at the bottom left of the

driver page that display two states "Device disconnected" or "Device connected".

GT-116

9

EN

3

3.1 Hold the pen

Hold the pen as you hold a normal pen or pencil. Adjust your grip so that you

can toggle the side switch easily with your thumb or forefinger. Be careful not to

accidentally press the switch while drawing or positioning with the pen.

Notice:

When not in use, place the pen in the pen case or on the desk. Do not place the

pen on the surface of screen, which may interfere with the use of other screen

cursor positioning equipment, may also cause your computer can not enter the

sleep mode.

3.2 Position the cursor

Move the pen slightly above the active area without touching the screen surface,

the cursor will move to the new position accordingly.

Press the pen tip on the screen to make a selection. Tap the screen once with the

pen tip, or touch it to the screen with enough pressure to register a click.

/ Pen Basic Operation

GT-116

10

EN

3.3 Click

Use the pen tip to tap once on the screen to register a click. Tap to highlight or

select an item on the screen and double-click to open it.

3.4 Move

Select the object, then slide the pen tip across the screen to move it.

3.5 Use the side buttons

The buttons on the pen can be set to two different customizable functions.

You can use the buttons whenever the pen tip is within 10mm of the display active

area.

You do not have to touch the pen tip to the display in order to use the switch.

GT-116

11

EN

3.6 Pen Nib Replacement

The nib will be worn off after using for a long time, then you need to replace a

new nib.

[1] Anticlockwise rotate the pen holder to open the cover, take a new nib out.

[2] Insert the pen nib into the hole on the bottom of the holder and tilt the pen to

pull out the old nib.

[3] Insert the new nib straight into the pen and push the nib slowly and firmly

until it stops.

Pen Nibs

Pen Nib Clip

GT-116

12

EN

4/ Using the Display

4.1 Power Button

The power button was placed on the left side of the digital screen, you need to

turn on the power switch before using.

4.2 Press Keys

There are 4 press keys on the top left side of the display, which you can modify

the functions according to your own habits, thus will help to improve your work

efficiency.

4.3 Touch Bar

The left side of the display is provided with a touch bar, you can slide up and

down to achieve zoom function, or you can self-define the function on the driver.

4.4 OSD Function

Enter OSD Menu:

[1] Press ① "Function Button" around three seconds until the OSD menu appears

and meanwhile the indicator will be on. The function of the Keys ② ③ ④ ⑤ will

become OSD function.

[2] In the menu, the function of ②③④⑤ will become as the following:

② AUTO: Before entering menu, its function is "auto adjustment".

After entering menu, its function is "back to previous menu".

③ MENU: Press to call up the menu, after entering menu, its function is "confirm".

④ - : After entering menu, its function is "down/left/decrease".

⑤ +: After entering menu, its function is "up/right/increase".

Exit OSD Menu:

[3] Press ①"Function Button" again for around three seconds until the indicator will

be off, the function of the Keys ②③④⑤ will become "short cuts function again".

GT-116

13

EN

5/ Function Setting

5.1 Working Area Setting

5.1.1 Using Multiple Monitors

Select the Working Area tab to define the relationship between pen movement on

the display and cursor movement on the monitor screen.

By default the entire active area of display maps to the entire monitor. If more

than one monitor is in use and you are in extended mode, you need to choose the

related monitor on the driver interface which you are going to map to.

If your monitors are in mirror mode (All monitors display the same content), the

display maps to the entire space on each monitor and the screen cursor is displayed

on each monitor simultaneously.

5.1.2 Working Area Setting

Define the display area that will be mapped to the screen area.

[1] Full Area: the entire active area of the display. This is the default setting.

[2] Screen Ratio: As a general rule, be 16:9.

[3] Customized Area:

1> Enter coordinate values.

2> Drag the corners of the foreground graphic to select the screen area.

GT-116

14

EN

①

②

③

5.1.3 Rotate Working Area

By changing the direction of the display to adapt to the left and right hand

operation. You can rotate the display by 0° , 90° , 180° or 270° .

5.2 Press Keys Function Setting

Default Setting: Place the cursor on the press key or click the press key to find the

default values.

Customized Setting: Select the function to be achieved on the pop-up dialog box,

then click "Apply" or "OK" to take effect.

Enable/Disable Press Keys: Check/Uncheck "Enable Press Keys".

GT-116

15

EN

①

②

③

④

⑤

The following shortcut key customization interface is displayed, with a total of 5

Settings.

① Custom: according to the use of custom or professional terms to set.

② Key combination function keys: Ctrl, Shift, Alt, Win+ any letter or other. Ctrl,

Shift, Alt, Win, you can select one or more of them, and you can arrange them in

any combination. Enter the corresponding Settings in the input box. For example:

deselect -Ctrl +D, enter task manager -Ctrl+Alt+Delete, etc.

③ Mouse Button Function: click the box, select the required function, can be set to

complete.

④ switch function: also click the box, select the required function.

⑤ Run the program function: click browse, select the connection, to achieve the

required run the program function.

GT-116

16

EN

5.3 Pen Buttons Function Setting

Select the function to be achieved on the pop-up dialog box, then click "Apply" or

"OK" to take effect.

5.4 Enable the Windows Ink feature

Microsoft Windows provides extensive support for pen input. Pen features are

supported in such as Microsoft Office, Windows Journal, Adobe Photoshop CC,

SketchBook 6 and so on.

GT-116

17

EN

5.5 Pressure Sensitivity Setting

The pressure sensitivity will be changed by dragging the slider up and down, the

smaller the value, the more pressure sensitive.

Drag upward (left): the pressure change is more obvious, small pressure produces a

great pressure.

Drag down (right): pressure change is weak, a lot of pressure produces less

pressure.

Click the button at the bottom right of the Settings box to reset the pressure

sensitivity to the default state.

For example: apply *N respectively the same pressure, under different pressure

coefficient produced different pressure effects. According to their habit of holding

the pen posture and the size of the hand for the appropriate pressure Settings.

Same press*N

Pressure 1

Same press *N

Pressure 2

*N *N

Press Sensitivity Adjustment Press Sensitivity Adjustment

GT-116

18

EN

5.6 Pen Pressure Testing

You can gradually apply pressure to the stylus on the screen to test the pressure

level. Click " " button to clear all the ink.

5.7 Enable the Windows Ink feature

Microsoft Windows provides extensive support for pen input. Pen features are

supported in such as Microsoft Office, Windows Journal, Adobe Photoshop CC,

SketchBook 6 and so on.

GT-116

19

EN

/ Specifications

6

Model GT-116

Screen

Panel Size 11.6 inch

Resolution 1920 x 1080 (16:9)

LCD Type IPS

Active Area 256.32 × 144.18mm

Contrast Ratio 1000:1

Brightness 220 cd/m2

Response Time 25ms

View Angle 89° /89° (H) /89° /89° (V) (Typ.) (CR ＞ 10)

Gamut 120% sRGB

Display Color 16.7M (8bit)

Touch

Touch Type Battery-Free Electromagnetic Resonance

Resolution 5080LPI

Pressure Level 8192

Accuracy ±0.5 mm (Center), ±3 mm (Corner)

Sensing Height 10mm

Report Rate 266PPS

Pen

Model PW507

Dimension 163.7 x Φ14.3mm

Buttons Two Customized Press Key

General

Output Voltage 12V 1A

Video Interface USB-C

Press Key 4 Customized Press Key

Dimension 350 x 198.6 x 11mm

Net Weight 0.76kg

OS Support Windows 7 or later, mac OS 10.12 or later

GT-116

20

EN

/ Trouble Shooting

7

Abnormal Phenomena Possible Solutions

Power indicator does not

flash

1. Make sure power is on.

2. Check the socket and power cable.

No display on the screen

1. Make sure power is on.

2. Correctly connect the cables.

3. If you connect the display with a laptop, please make

sure the display is on the right display mode: extend or

duplicate mode.

4. Check whether the side indicator shows green, if not,

it means no signal in. Please reboot your computer or

reconnect the cable.

5. Is the signal wire broken or bent? If so, please replace the

signal wire.

No signal

1. Make sure the cables are well connected.

2. If you use a desktop, make sure the HDMI port is

plugged into the graphic card on the tower, but not into

the motherboard.

3. If you use a Windows OS computer, make sure to press

''Windows+P'' on keyboard, then choose Duplicate or

Extend. Don't choose Computer Only or Projector Only.

4. If there is no HDMI port on your computer, you need

an extra HDMI adapter. We don't recommend a USB to

HDMI adapter. Also, we don't recommend a USB hub. We

recommend DVI/ VGA/ Display Port/ Type-C/ Thunderbolt,

etc. to HDMI adapters.

Images are blurred Please set the display resolution with 1920 x 1880.

7.1 Possible Breakdowns Related to DISPLAY

Page is loading ...

Huion KAMVAS PRO 12 User manual

Huion KAMVAS PRO 12 User manual

in other languages

Related papers

Other documents