2. Office
  3. Office furniture
  4. Computer desks
  5. Anthro
  6. GT23BK
GT23BK

Anthro GT23BK, MiniCart User manual

  • Hello! I'm a chat assistant and I'm ready to help with questions about the Anthro MiniCart assembly. I've reviewed the assembly instructions provided, and I'm familiar with the steps for installing casters, attaching shelves, and the specific considerations for GT23xx, GT23xx4, and GT23xxGL models. I am also aware of the parts and tools mentioned in the document. Please feel free to ask me anything about the assembly process.
  • What is the overall height of the MiniCart using 2 3/8" casters?
    How much is the overall height increased if using 4" casters?
    How much is the overall height decreased if using Glides?
    How many Base Tube Screws are needed to attach the Base Tube to each Leg?
TECHNOLOGY FURNITURE®
300-5385-00
*300-5385-00*
Anthro MiniCart
Assembly Instructions
01– Insert Screws ............................ Qty. 4................. 325-5052-00
02– 2 3/8" Non-Locking Casters ........ Qty. 2 ............... 150-5002-03*
03– Caster Inserts ........................... Qty. 4...............525-1000-00*
04– 2 3/8" Locking Casters ................ Qty. 2...............150-5003-03*
05– 1.75" Large End Caps ............ Qty. 2..................175-5021-xx
06– Base Tube Screws ..................... Qty. 3................. 325-5000-00
07– MiniCart Base Tube ..................... Qty. 1 .................. 125-5004-xx
08– Support Screws ........................ Qty. 6................. 325-5010-00
09– Vertical Legs .............................. Qty. 3..................125-5020-xx
10– Clamp Screws........................... Qty. 6................. 325-5086-00
11– Shelf Supports .......................... Qty. 6..................175-5060-xx
12– Shelf Clamps ............................. Qty. 6 .................. 175-5059-xx
Enclosed Parts List
Detailed views of all Hardware is provided with each Assembly Step 13– MiniCart Shelves ...................... Qty. 2 ..................100-6003-xx
14– 1.5" Small End Caps ............... Qty. 3 ..................175-5020-xx
All Fastener quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra
Fasteners included, which are not counted in the Parts List.
To make the assembly of your Anthro MiniCart even easier, we have included
all of the required tools (not shown above). The handy Hex Driver Bit can be
used in your electric drill in place of the Hex Driver.
Hex Driver 5/32" ........................ Qty. 1 ................. 375-5000-00
Hex Driver Bit 5/32" .................. Qty. 1 ................. 375-5003-00
8 oz. Rubber Mallet .................. Qty. 1 ................. 375-5022-00
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS! Document # 300-5068-00
Step 7
Install all four Caster Inserts into the Base Tube and
secure (fully tighten) with one Insert Screw per Insert.
Next, push the Casters, (locking ones in front) into the
Caster Inserts.
Step 8
Carefully rotate the Shelf Assembly (from Step 6),
upside down as shown.
Place the Base Tube Assembly (from Step 7) onto the
Vertical Legs of the Shelf Assembly.
Attach the Base Tube to each Leg using a total of three
Base Tube Screws.
Tighten all Support and Base Tube Screws.
Step 9
Rotate your MiniCart over onto the Casters.
Pop the three 1.5" Small End Caps into the Vertical Legs
and the two 1.75" Large End Caps into the Base Tube.
Congratulations! Your MiniCart assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale flyers.
Thank you for choosing Anthro!
March 2006
These Assembly Instructions are
for the GT23xx.
Before beginning assembly of your
Anthro MiniCart, please take a moment
to review the parts listed below to verify
that your shipment is complete.
✔Does your Cart have 4" Casters?*
(Such as a GT23xx4. Your Caster Part
Numbers are given here.)
✔Does your Cart have Glides?*
(Such as a GT23xxGL. Your Glide and Glide
Insert Part Numbers are given here.)
4" Locking Caster
150-5011-03
4" Non-Locking Caster
150-5010-03
Glide Insert
525-1004-00
Glide
325-5042-00
Questions? 1-800-325-3841
Insert Screw
(small pink patch on end)
325-5052-00
Base Tube Screw
325-5000-00
GLIDES ONLY
Thread each Glide
into the Glide Inserts
04 06
07
03 02
09
10
05
12
01
08
11
14
13
1.5" Small End Cap
1.75" Large End Cap
Locking Casters
Anthro MiniCart
Assembly Instructions
Anthro Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062
Step 1
Before proceeding, please review the Assembly
Instructions of all Anthro Products you purchased
and are planning to include in this installation.
Step 3
Attach three Shelf Supports to each Shelf.
Begin by first installing a Shelf Clamp into the Shelf
notch. Be sure the pointed barbs face towards the
outer Shelf edge.
Next, slide a Shelf Support into the recesses of the
Shelf Clamp and Shelf. Push in as far as possible.
Finally, secure with a Clamp Screw.
anthro.com
Step 4
Loosely attach one Shelf to Hole 11 from the bottom (coped
end) of one Vertical Leg using a Support Screw.
NOTE: This will place your lower Shelf 19" from the floor using
the standard 2 3/8" Casters.
Step 5
Loosely attach the remaining Shelf to Hole 2 from the
top (non-coped end) of the Vertical Leg Assembly (from
Step 4) using one Support Screw.
NOTE: Handle the Shelf Assembly carefully until the Cart
is fully assembled.
Step 6
Loosely attach the 2nd and 3rd Vertical Legs to the
Shelf Assembly (from Step 5) using one Support
Screw per Shelf Support.
TIP: Use the holes in the Vertical Legs as a ruler to
ensure that your Support Screws are installed into the
correct locations.
Questions? 1-800-325-3841
First
Next
Finally Support Screw
325-5010-00
Clamp Screw
325-5086-00
Barbs
Step 2
Decide on the Shelf locations for your MiniCart. You can
place your Shelves almost anywhere on the Vertical Legs
(the Legs are stamped at 1" increments).
For a Lower Shelf location that is higher or lower than
19" from the floor, refer to the illustrations shown at right
to determine which holes to attach your Lower Shelf.
Once your MiniCart is assembled, it is very
difficult to move a Shelf without taking the
entire Cart apart and starting over.
NOTE: These instructions will place your Lower Shelf
19" from the floor using the standard 2 3/8" Castors.
GT23xx with 2 3/8" Casters
GT23xx4 with 4" Casters
GT23xxGL with Glides
Hole 12=20"
Hole 11=19" (measured from the coped end)
Hole 10=18"
Hole 11=20"
Hole 10=19"
Hole 9=18"
Hole 9=20"
Hole 8=19"
Hole 7=18"
REMINDER: You may want to
measure your equipment to
make sure it fits between the
selected Shelf locations.
Coped end
19"
19"
19"
Support Screw
325-5010-00
Support Screw
325-5010-00
GT23xx
Overall MiniCart height is
28" using 2 3/8" Casters
NOTE: Add 1" to overall height for 4" Casters and
subtract 3" from overall height for Glides.
Bottom
(coped)
end
Hole 11=19"
(using 2 3/8" Casters)
Insert one Support Screw
through each Shelf Support
To p
(non-coped)
end Hole 2
Top
(non-coped)
end
Bottom
(coped)
end
NOTE: These Instructions
will create approximately
8" of usable space between
your Shelves.
Lower Shelf
/