HK Audio Premium PR:O 15 XA User manual

Brand: HK Audio

Model: Premium PR:O 15 XA

Type: User manual

Selfpowered Cabinets

Manual 1.4

English

Deutsch

Français

Español

Italiano

PR:O 8 A • PR:O 10 XA • PR:O 12 A • PR:O 12 MA

PR:O 15 A • PR:O 15 XA • PR:O 18 Sub A • PR: O 210 Sub A

Wichtige Sicherheitshinweise!

Bitte vor Gebrauch lesen und für späteren Gebrauch

aufbewahren!

Important Safety Instructions

Before connecting, read instructions

Important Advice on Safety!

Please read before use and keep for later use!

• Read all of these instructions!

• Save these instructions for later use!

• Follow all warnings and instructions marked on the product!

• Do not use this product near water, i.e. bathtub, sink, swimming pool,

wet basement, etc.

• Do not place this product on an unstable cart, stand or table. The product may fall,

causing serious damage to the product or to persons!

• Slots and openings in the cabinet and the back or bottom are provided for ventilation;

to ensure reliable operation of the product and to protect it from overheating, these

openings must not be blocked or covered. This product should not be placed in a built-

in installation unless proper ventilation is

provided.

• This product should not be placed near a source of heat such as a stove,

radiator, or another heat producing amplifier.

• Use only the supplied power supply or power cord. If you are not sure of the type of

power available, consult your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this product where

persons will walk on the cord.

• Never break off the ground pin on the power supply cord.

• Power supply cords should always be handled carefully. Periodically check cords for

cuts or sign of stress, especially at the plug and the point where the cord exits the

unit.

• The power supply cord should be unplugged when the unit is to be unused for long

periods of time.

• If this product is to be mounted in an equipment rack, rear support should be

provided.

• This product should be used only with a cart or stand that is recommended by

HK AUDIO

• Never push objects of any kind into this product through cabinet slots as they may

touch dangerous voltage points or short out parts that could result in risk of fire or

electric shock. Never spill liquid of any kind on the product.

• Do not attempt to service this product yourself, as opening or removing covers may

expose you to dangerous voltage points or other risks. Refer all servicing to qualified

service personnel.

• Clean only with dry cloth.

• Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade or the third prong are

provided for the safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

• Place the product always in a way that the mains switch is easily accessible.

• Unplug this product from the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

• When the power cord or plug is damaged or frayed.

• If liquid has been spilled into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally when the operating instructions are followed.

• If the product has been dropped or the cabinet has been damaged.

• If the product exhibits a distinct change in performance, indicating a need of service!

• Adjust only these controls that are covered by the operating instructions since impro-

per adjustment of other controls may result in damage and will often require extensive

work by a qualified technician to restore the product to normal operation.

• Exposure to extremely high noise levels may cause a permanent hearing loss.

• Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly

everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient

time. The U.S. Government´s Occupational Safety and Health Administration (OSHA)

has specified the following permissible noise level exposures:

Duration Per Day In Hours Sound LeveldBA, Slow Response

8 90

6 92

4 95

3 97

2 100

11/2 102

1 105

1/2 110

1/4 or less 115

• According to OSHA, any exposure in excess of the above permissible limits could

result in some hearing loss.

• Ear plug protectors in the ear canals or over the ears must be worn when operating this

amplification system in order to prevent a permanent hearing loss if exposure is in excess

of the limits as set forth above. To ensure against potentially dangerous exposure to

high sound pressure levels, it is recommended that all persons exposed to equipment

capable of producing high sound pressure levels such as this amplification system be

protected by hearing protectors while this unit is in operation.

• Fuses: Replace with IEC 127 (5x 20 mms) type and rated fuse for best

performance only.

TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO MOISTURE OR RAIN. DO NOT OPEN CASE; NO USER SERVICE-ABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Version 1.1 11/2006

• The unit has been built by HK AUDIO

in accordance with IEC 60065 and left the

factory in safe working order. To maintain this condition and ensure non-risk opera-

tion, the user must follow the advice and warning comments found in the operating

instructions. The unit conforms to Protection Class 1 (protectively earthed).

• HK AUDIO

ONLY GUARANTEE THE SAFETY, RELIABILITY AND EFFICIENCY OF

THE UNIT IF:

• Assembly, extension, re-adjustment, modifications or repairs are carried out by

HK AUDIO

or by persons authorized to do so.

• The electrical installation of the relevant area complies with the requirements of IEC

(ANSI) specifications.

• The unit is used in accordance with the operating instructions.

• The unit is regularly checked and tested for electrical safety by a competent technician.

WARNING:

• If covers are opened or sections of casing are removed, except where this can be done

manually, live parts can become exposed.

• If it is necessary to open the unit this must be insulated from all power sources. Please

take this into account before carrying out adjustments, maintenance, repairs and

before replacing parts.

• The appliance can only be insulated from all power sources if the mains connection is

unplugged.

• Adjustment, maintenance and repairs carried out when the unit has been opened and is

still live may only be performed by specialist personnel who are authorized by the manuf-

acturer (in accordance with VBG 4) and who are aware of the associated hazards.

• Loudspeaker outputs which have the IEC 417/5036 symbol (Diagram 1, below) can

carry voltages which are hazardous if they are made contact with. Before the unit

is switched on, the loudspeaker should therefore only be connected using the lead

recommended by the manufacturer.

• Where possible, all plugs on connection cables must be screwed or locked onto the

casing.

• Replace fuses only with IEC127 type and specified ratings.

• It is not permitted to use repaired fuses or to short-circuit the fuse holder.

• Never interrupt the protective conductor connection.

• Surfaces which are equipped with the "HOT" mark (Diagram 2, below), rear panels or

covers with cooling slits, cooling bodies and their covers, as well as tubes and their

covers are purposely designed to dissipate high temperatures and should therefore not

be touched.

• High loudspeaker levels can cause permanent hearing damage. You should

therefore avoid the direct vicinity of loudspeakers operating at high levels.

Wear hearing protection if continuously exposed to high levels.

MAINS CONNECTION:

• The unit is designed for continuous operation.

• The set operating voltage must match the local mains supply voltage.

• The unit is connected to the mains via the supplied power unit or power cable.

• Power unit: Never use a damaged connection lead. Any damage must be rectified by a

competent technician.

• Avoid connection to the mains supply in distributor boxes together with several other

power consumers.

• The plug socket for the power supply must be positioned near the unit and must be

easily accessible.

PLACE OF INSTALLATION:

• The unit should stand only on a clean, horizontal working surface.

• The unit must not be exposed to vibrations during operation.

• Place the product always in a way that the mains switch is easily accessible.

• Keep away from moisture and dust where possible.

• Do not place the unit near water, baths, wash basins, kitchen sinks, wet areas, swim-

ming pools or damp rooms. Do not place objects containing liquid on the unit - vases,

glasses, bottles etc.

• Ensure that the unit is well ventilated.

• Any ventilation openings must never be blocked or covered. The unit must be positi-

oned at least 20 cm away from walls. The unit may only be fitted in a rack if adequate

ventilation is ensured and if the manufacturer's installation instructions are followed.

• Keep away from direct sunlight and the immediate vicinity of heating elements and

radiant heaters or similar devices.

• If the unit is suddenly moved from a cold to a warm location, condensation can form

inside it. This must be taken into account particularly in the case of tube units. Before

switching on, wait until the unit has reached room temperature.

• Accessories: Do not place the unit on an unsteady trolley, stand, tripod, base or table.

If the unit falls down, it can cause personal injury and itself become damaged. Use the unit

only with the trolley, rack stand, tripod or base recommended by the manufacturer

or purchased together with the unit. When setting the unit up, all the manufacturer's

instructions must be followed and the setup accessories recommended by the manuf-

acturer must be used. Any combination of unit and stand must be moved carefully. A

sudden stop, excessive use of force and uneven floors can cause the combination of

unit and stand to tip over.

• Additional equipment: Never use additional equipment which has not been

recommended by the manufacturer as this can cause accidents.

• To protect the unit during bad weather or when left unattended for prolonged periods,

the mains plug should be disconnected. This prevents the unit being damaged by

lightning and power surges in the AC mains supply.

Diagram 1 Diagram 2

• Das Gerät wurde von HK AUDIO

gemäß IEC 60065 gebaut und hat das Werk in si-

cherheitstechnisch einwandfreiem Zustand verlassen. Um diesen Zustand zu erhalten

und einen gefahrlosen Betrieb sicherzustellen, muss der Anwender die Hinweise und

die Warnvermerke beachten, die in der Bedienungsanleitung enthalten sind. Das Gerät

entspricht der Schutzklasse I (schutzgeerdet).

• DIE SICHERHEIT, ZUVERLÄSSIGKEIT UND LEISTUNG DES GERÄTES WIRD VON

HK AUDIO

NUR DANN GEWÄHRLEISTET, WENN:

• Montage, Erweiterung, Neueinstellung, Änderungen oder Reparaturen von

HK AUDIO

oder von dazu ermächtigten Personen ausgeführt werden.

• die elektrische Installation des betreffenden Raumes den Anforderungen von IEC

(ANSI)-Festlegungen entspricht.

• das Gerät in Übereinstimmung mit der Gebrauchsanweisung verwendet wird.

WARNUNG:

• Wenn Abdeckungen geöffnet oder Gehäuseteile entfernt werden, außer wenn dies von

Hand möglich ist, können Teile freigelegt werden, die Spannung führen.

• Wenn ein Öffnen des Gerätes erforderlich ist, muss das Gerät von allen Spannungs-

quellen getrennt sein. Berücksichtigen Sie dies vor dem Abgleich, vor einer Wartung,

vor einer Instandsetzung und vor einem Austausch von Teilen.

• Ein Abgleich, eine Wartung oder eine Reparatur am geöffneten Gerät unter Spannung

darf nur durch eine vom Hersteller autorisierte Fachkraft (nach VBG 4) geschehen, die

mit den verbundenen Gefahren vertraut ist.

• Lautsprecher-Ausgänge, die mit dem IEC 417/5036-Zeichen (Abb.1, s.unten) versehen

sind können berührungsgefährliche Spannungen führen. Deshalb vor dem Einschalten

des Gerätes Verbindung nur mit dem vom Hersteller empfohlenen Anschlusskabel

zum Lautsprecher herstellen.

• Alle Stecker an Verbindungskabeln müssen mit dem Gehäuse verschraubt oder verrie-

gelt sein, sofern möglich.

• Es dürfen nur Sicherungen vom Typ IEC 127 und der angegebenen Nennstromstärke

verwendet werden.

• Eine Verwendung von geflickten Sicherungen oder Kurzschließen des Halters ist unzu-

lässig.

• Niemals die Schutzleiterverbindung unterbrechen.

• Oberflächen, die mit dem "HOT"-Zeichen (Abb.2, s.unten) versehen sind, Rückwände

oder Abdeckungen mit Kühlschlitzen, Kühlkörper und deren Abdeckungen, sowie

Röhren und deren Abdeckungen können im Betrieb erhöhte Temperaturen annehmen

und sollten deshalb nicht berührt werden.

• Hohe Lautstärkepegel können dauernde Gehörschäden verursachen. Vermeiden Sie

deshalb die direkte Nähe von Lautsprechern, die mit hohen Pegeln betrieben werden.

Verwenden Sie einen Gehörschutz bei dauernder Einwirkung hoher Pegel.

NETZANSCHLUSS:

• Das Gerät ist für Dauerbetrieb ausgelegt.

• Die eingestellte Betriebsspannung muss mit der örtlichen Netzspannung

übereinstimmen.

• Der Anschluss an das Stromnetz erfolgt mit dem mitgelieferten Netzteil oder

Netzkabel.

• Netzteil: Eine beschädigte Anschlussleitung kann nicht ersetzt werden.

Das Netzteil darf nicht mehr betrieben werden.

• Vermeiden Sie einen Anschluss an das Stromnetz in Verteilerdosen zusammen mit

vielen anderen Stromverbrauchern.

• Die Steckdose für die Stromversorgung muss nahe am Gerät angebracht und leicht

zugänglich sein.

AUFSTELLUNGSORT:

• Das Gerät sollte nur auf einer sauberen, waagerechten Arbeitsfläche stehen.

• Das Gerät darf während des Betriebs keinen Erschütterungen ausgesetzt sein.

• Feuchtigkeit und Staub sind nach Möglichkeit fernzuhalten.

• Das Gerät muss immer so aufgestellt werden, dass der Netzschalter frei zugänglich ist.

• Das Gerät darf nicht in der Nähe von Wasser, Badewanne, Waschbecken, Küchenspüle,

Nassraum, Swimmingpool oder feuchten Räumen betrieben werden. Keine mit Flüs-

sigkeit gefüllten Gegenstände -Vase, Gläser, Flaschen etc. auf das Gerät stellen.

• Sorgen Sie für ausreichende Belüftung der Geräte.

• Eventuelle Ventilationsöffnungen dürfen niemals blockiert oder abgedeckt werden.

Das Gerät muss mindestens 20 cm von Wänden entfernt aufgestellt werden. Das

Gerät darf nur dann in ein Rack eingebaut werden, wenn für ausreichende Ventilation

gesorgt ist und die Einbauanweisungen des Her stellers eingehalten werden.

• Vermeiden Sie direkte Sonneneinstrahlung sowie die unmittelbare Nähe von Heizkör-

pern und Heizstrahlern oder ähnlicher Geräte.

• Wenn das Gerät plötzlich von einem kalten an einen warmen Ort gebracht wird, kann

sich im Geräteinnern Kondensfeuchtigkeit bilden. Dies ist insbesondere bei Röhrenge-

räten zu beachten. Vor dem Einschalten solange warten bis das Gerät Raumtempera-

tur angenommen hat.

• Zubehör: Das Gerät nicht auf einen instabilen Wagen, Ständer, Dreifuß, Untersatz

oder Tisch stellen. Wenn das Gerät herunterfällt, kann es Personenschäden verur-

sachen und selbst beschädigt werden. Verwenden Sie das Gerät nur mit einem vom

Hersteller empfohlenen oder zusammen mit dem Gerät verkauften Wagen, Rack, Stän-

der, Dreifuß oder Untersatz. Bei der Aufstellung des Gerätes müssen die Anweisungen

des Herstellers befolgt und muss das vom Hersteller empfohlene Aufstellzubehör

verwendet werden. Eine Kombination aus Gerät und Gestell muss vorsichtigt bewegt

werden. Plötzliches Anhalten, übermäßige Kraftanwendung und ungleichmäßige

Böden können das Umkippen der Kombination aus Gerät und Gestell bewirken.

• Zusatzvorrichtungen: Verwenden Sie niemals Zusatzvorrichtungen, die nicht vom

Hersteller empfohlen wurden, weil dadurch Unfälle verursacht werden können

• Zum Schutz des Gerätes bei Gewitter oder wenn es längere Zeit nicht beaufsichtigt

oder benutzt wird, sollte der Netzstecker gezogen werden.

Dies verhindert Schäden am Gerät aufgrund von Blitzschlag und Spannungsstößen

im Wechselstromnetz.

Abb.1 Abb.2

Page is loading ...

PREMIUM PR:O Active 1.4

Welcome to the HK Audio family!

Thank you for choosing (yet another) HK AUDIO

product!

PREMIUM PR:O active enclosures are end-to-end

sound reinforcement solutions comprising lou-

dspeakers, power amps, and integrated circuitry

precision-tuned to control these components.

These satellites, bass bins, and monitors may be

combined with one another. Deployed as standalone

enclosures, they readily integrate into other sound

reinforcement systems. Feel free to connect passive

loudspeakers – ideally, a passive PREMIUM PR:O

Series enclosure - to the parallel circuits of all active

models except the PR:O 18 Sub A and the PR:O 210

Sub A to extend your system without having to add

another power amp to your rig. What’s more, our

engineers developed new technologies specifically to

maximize the performance of PREMIUM PR:O active

cabinets.

Warranty

warranty card to extend your warranty to five years

free of charge!

Important note: Be sure to register each PREMIUM

PR:O powered enclosure individually.

To this end, use the convenient online registration

option at www.hkaudio.com.

If you are unable to register online, please complete

the enclosed warranty card completely and mail or

fax it to us. Registration is only valid if the warranty

card is filled out and returned to HK AUDIO or the

device is registered via Internet within the registrati-

on period. We are also interested in learning where

and by whom our devices are used. This information

will help us design future products. Your data are of

course protected by privacy laws.

Thank you!

HK AUDIO

Technical Service

Postfach 1509

66959 St. Wendel, Germany

Table of contents

1 PR:O 8 A, PR:O 10 XA, PR:O 12 A, PR:O 12 MA, PR:O 15 A, PR:O 15 XA . . . . . . . . . . . . . 6

1.1 Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Setting Up and Connecting Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3 Operating Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.5 Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2 PR:O 18 Sub A, PR:O 210 Sub A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2 Setting Up and Connecting the Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Operating Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3 Tips and Tricks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5 Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Digital Amping – Enhanced efficiency and dynamics

With an efficiency rating topping the 90% mark,

digital power amps are smaller, lighter, and more

compact than conventional amps. The reduced ther-

mal load on components clearly enhances reliability.

The slew rate is far faster and the attenuation factor

is higher, resulting in perceptibly more responsive

and accurate performance.

RMS/Peak-Limiter

A smart combination RMS / Peak Limiter achieves

balanced dynamic response at high loads while

protecting components against overload. (The

PR:O 18 Sub A and the PR:O 210 Sub A come

without an RMS Limiter.)

Subsonic-Filter – Protection against low-frequency

rumble

The integrated subsonic filter eliminates accidental

and unintentional signals such footfalls, wind, or

the sound of a hand inadvertently brushing a micro-

phone. It cuts these frequencies drastically, freeing

energy to better render bass impulses. The result:

delightfully dynamic and natural-sounding low-end

response.

DuoTilt 3/7™ – Making the most of sonic energy

The specially developed DuoTilt™ pole mount allows

sound energy to be utilized far more efficiently.

DuoTilt™ offers 3° and 7° angles of tilt, enabling

perfect satellite-to-audience alignment. Troublesome

ceiling reflections are minimized, yielding a clearer,

punchier, and tighter sonic image. MonoTilt™

(PR:O 8 A) offers one angle of tilt.

English

PREMIUM PR:O Active 1.4

1 PR:O 8 A, PR:O 10 XA,

PR:O 12 A, PR:O 12 MA,

PR:O 15 A, PR:O 15 XA

1.1 Control Features

1 Gain

This knob adjusts the input level.

2 Tone (not available on the PR:O 12 MA)

The Tone knob lets you optimize your active speaker

cabinet for music or speech applications. It uses

a special filtering setup that adapts frequency

response to suit the given requirements. Room

acoustics vary as does the cabinet’s position, so we

recommend you find the optimum position by piping

in a full-fledged music signal, using a microphone,

and twisting the knob. Turning it towards Speech

boosts vocal signals, and turning it towards Music

conjures a bigger, bolder sonic image with more low

end and less midrange frequencies.

The Tone knob lets you tune the speaker cabinet to

suit music or public address applications. Its special

filtering circuit adapts its frequency response to the

given requirements.

Note: Twisting the Tone knob counterclockwise to-

wards Music gradually attenuates a broad midrange

frequency band with a center frequency of 1500 Hz

(2500 Hz -PR:O 10 XA, 2600 Hz - PR:O 8 A). The

maximum cut is 2 dB, achieved by setting the knob

to the far left position. At the same time, this ad-

justment boosts bass frequencies in the range of 80

to 100 Hz in equal measure by up to 2 dB. Twisting

the Tone knob counterclockwise towards Speech

achieves the opposite effect, boosting the midrange

frequency band and cutting bass frequencies accor-

dingly by up to 2 dB.

A special corrective circuit compensates for this EQ

effect so that the perceived volume level remains the

same despite the change in tone. Setting the knob to

the center position defeats the filter.

3 Mic/Line Switch (not on the PR:O 12 MA)

When patching in a microphone, adjust the input

gain by setting the Line/Mic button to Mic. This

provides a 30-dB gain boost, thereby optimizing the

input for microphone signals.

4 Input

This electronically balanced XLR/ 1/4" combi input

accepts mixer signals (pin 1= ground, 2= +, 3= -).

5 Through

This parallel output patches the incoming line signal

through, for example, to other PREMIUM PR:O

active speakers or monitors.

6 Limiter Status LED

This dichromic LED indicates the signal level and

limiter status. Green means the signal level is okay;

red means the limiter has engaged and is respon-

ding to high-volume signal peaks.

CAUTION! This is not a clip LED. It’s okay if it

lights up red briefly every now and then; this merely

indicates the RMS Limiter is operating. If the signal

LED remains constantly in the red at signal peaks,

check the source signal’s input level and back off

the speaker’s Gain knob. A status LED that lights

up red continuously indicates there is a fault in the

speaker system.

7 Power Switch

This is the PREMIUM PR:O powered cabinet’s on/off

button. The signal LED lights up green to indicate

the cab is powered up.

Note: The Power button is embedded to prevent

unintentional actuation. When set to POWER ON,

the button sits almost flush with the connector pa-

nel. This ensures it is not engaged accidentally, yet

remains readily accessible.

1 4 5 6 87

8 Mains Input

Use the factory-included locking power cord to con-

nect this socket to a mains outlet. The catch holds

the cord in place, preventing accidental unplugging.

You must release the yellow catch on the bottom of

the plug before you can remove the cord.

Note: This socket also accepts a standard Euro

mains cable, but it will not lock it in place.

9 Parallel Speaker Out

Use this Speakon NL4 output to connect another

passive PREMIUM PR:O enclosure or another

manufacturer’s passive cabinet.

Be sure to watch the impedance rating, connecting

no more than one enclosure with an impedance no

lower than 8 ohms. The power amp delivers up to

300 watts to this output.

1.2 Setting Up and Connecting

Cabinets

Connect cords routed from your mixer (monitor

out, line out, or a similar output) to the balanced

Input sockets using a cord equipped with standard

XLR microphone connectors. Make sure the XLR

connectors’ terminals are configured as follows:

1= ground, 2= +, 3= -.

If you wish to connect a microphone directly to the

PREMIUM PR:O active cabinet without going into

a mixer first, plug it into the balanced Input socket

and set its input sensitivity to Mic. Use a standard

XLR microphone cord to do this. Make sure the XLR

connectors’ terminals are configured as follows:

1= ground, 2= +, 3= -.

1.3 Operating Speakers

• First make sure the powered cabinet is off.

CAUTION! Make sure the local mains voltage mat-

ches the PREMIUM PR:O active cabinet’s specified

voltage. If you connect the PREMIUM PR:O cab to

the wrong mains voltage, you may destroy its elec-

tronic components.

• Back the Gain and Line/Mic knobs all the way off,

turning them counterclockwise as far as they will go.

When connecting line signals, be sure to first switch

on all other connected components first; that is, the

connected mixer and signal sources patched into

it, such as keyboards, instrument amps, effects and

so forth. Confirm that the PREMIUM PR:O powered

enclosure’s Mic/Line control is set to the correct

mode, the standard mode being Line.

Again, always switch on the PREMIUM PR:O active

cabinet last, that is, after you switch on all con-

nected devices. After you power the system up by

engaging the Power switch, a system check prompts

the fan to briefly kick on and back off again in about

five seconds. The fan is temperature-controlled, ac-

tuating only at very high volumes and temperatures

requiring cooling.

After you power up the cab by engaging the Power

switch, the Power LED lights up green when the

cabinet receives mains power. Set the Gain Line In

knob to the center or 12 o’clock position (= 0 dBV).

This is the preferred level if you have connected a

mixer to the PREMIUM PR:O active cabinet. If you

are patching a CD player or keyboard straight into

the cab, turn the Gain Line In knob clockwise all the

way to the far right to achieve maximum volume. If

the input signal is still too weak, boost the level at

the signal source, for instance, by adjusting an MP3

player’s volume knob.

If necessary, you can turn the PREMIUM PR:O

powered enclosure’s Gain knob counterclockwise

to the far left position and then press the Mic/Line

button. This boosts the input signal by 30 dB. Then

adjust the input gain by slowly turning the Gain

knob to the right until you attain the desired volume.

For the best audio results, ensure the Limiter LED

(red) does not light up continuously.

1.4 Settings

Adjusting volume with the Gain knob

Twist this knob and engage the Mic/Line switch line

to adjust microphone and line signal levels.

If you hear distortion or saturated signals, first check

the signal sources and, if possible, reduce the out-

put signal level there. If you cannot adjust the level

of the signal routed to the PREMIUM PR:O active

cabinet at the source, match it to the power amps by

backing off the Gain Line In knob.

CAUTION: Never tape over the plug’s ground

terminal - this endangers lives!

Tone (not available on the PR:O 12 MA)

Starting at the center or 12 o’clock position, you

can EQ the sonic image by turning the knob to the

right or left. Set it to MUSIC to attenuate midrange

frequencies somewhat and boost the low range fre-

quencies for live or CD signals.

Setting the knob to SPEECH enhances intelligibility

for public address purposes.

A corrective circuit automatically compensates

for EQ, balancing out the overall volume for each

setting.

1.5 Alignment

HK Audio DuoTilt™

(apart from the PR:O 12 MA, HK Audio Mono Tilt™

with a 3° angle tilt for the PR:O 8 A)

The HK AUDIO DuoTilt™ pole mount lets you align

PREMIUM PR:O active cabinets along the horizon-

tal plane to prevent or reduce troublesome ceiling

reflections. The front aperture of the HK AUDIO

DuoTilt™ provides a 3° angle, the rear aperture a 7°

angle of tilt.

If you set the full-range cabinets on a fully extended

cabinet tripod or mounting pole, opt for the 7° ang-

le. This setting works especially well when addres-

sing fewer listeners standing close to the speakers.

If you wish to address more listeners further from

the speakers, opt for the 3° angle on the HK AUDIO

DuoTilt™.

English

PREMIUM PR:O Active 1.4

Curving cable (for the PR:O 8 A only)

Included you’ll find a curving cable. It aligns the

PR:O 8 A vertically, for instance, if you wish to

install the enclosure or mount it to a from a truss.

Simply attach it using the bolts at the bottom of the

cabinet’s housing.

45°

Attaching the curving cable: The curving cable lets

you precisely aim the flown PR:O 8 A cab.

It attaches to the back of the PR:O 8 A.

• Remove the bottom two bolts from the connector

panel.

• Place the washers over the two holes.

• Insert the bolts to fasten the two plates attached

to the curving cable to the cabinet at a 45° angle

(refer to the diagram).

Note: The plates must be aligned to a 45° angle to

ensure safe operation!

• Tighten the bolts.

The cable kit includes:

- two washers

- two 5x25 mm recessed

hex-head bolts

- one cable with mounting plates

Caution: The curving cable serves solely to tilt the

cabinet; it is not a rigging point!

2 PR:O 18 Sub A, PR:O 210 Sub A

2.1 Control Features

1 Out L / Out R (Line Out Mid / High)

These two electronically balanced XLR inputs serve

to connect PREMIUM PR:O satellites (pin 1= ground,

2= +, 3= -).

2 Input L / Input R

These two electronically balanced XLR / 1/4" combi

inputs accept signals from mixing consoles

(pin 1= ground, 2= +, 3= -).

3 Through L / Through R

These two parallel outputs patch incoming line

signals through, for example, to other PREMIUM

PR:O active speakers or monitors (pin 1= ground,

2= +, 3= -).

4 Gain Bass

This knob adjusts the input level (center position =

0 dBV).

The 12 o’clock position is the ideal starting point

when operating the subwoofer in combination with a

PREMIUM PR:O active cabinet. Then you can simply

twist the knob to the left or right to cut and boost

bass frequencies. If you connect a PREMIUM PR:O

satellite, first set the Gain knob to the center detent

and then adjust the level to suit the given sound

reinforcement situation.

5 X-Over-Bass

The active crossover can serve to vary the top cu-

toff frequency of the subwoofer with a range of 75

to 150 Hz. The best cutoff frequency for the given

application depends on the surroundings and

satellite, so you will have to experiment.

Note: If you set the cutoff to a frequency higher than

110 Hz, the subwoofer will render mostly the lower

frequencies of signals generated by bass guitars,

kick drums, and low-end keyboard sounds. If you

set the cutoff to a frequency higher than 110 Hz, the

subwoofer will also render the lower frequencies of

voices and other sound sources.

6 Phase

The Phase switch changes the subwoofer’s phase

position to match it to the connected satellite’s

phase position (0° – 180°). Set the switch to 0° when

operating the PR:O 18 Sub A in combination with a

PREMIUM PR:O active cabinet. The PR:O 210 Sub

A's phase has to be reversed 180° to ensure it is in

phase with PREMIUM PR:O mid-/high-range units.

You may have to invert the phase for combinations

with other enclosures. If you are unsure, simply try

the 180° setting. If the bass response changes and

the signal sounds weak and washed out, the phase

setting is incorrect.

7 Limiter Status LED

This dichromic LED indicates the signal level and

limiter status. Green means the signal level is okay;

red means the limiter has engaged and is respon-

ding to high-volume signal peaks.

CAUTION! This is not a clip LED. It’s okay if it

lights up red briefly every now and then; this merely

indicates the RMS Limiter is operating. If the signal

LED remains constantly in the red at signal peaks,

check the source signal’s input level and back off

the speaker’s Gain knob. A status LED that lights

up red continuously indicates there is a fault in the

speaker system.

8 Power Switch

This is the PREMIUM PR:O powered cabinet’s on/off

button. The signal LED lights up green to indicate

the cab is powered up.

Note: The Power button is embedded to prevent

unintentional actuation. Set to Power On, the button

sits almost flush with the connector panel. This

ensures it is not engaged accidentally, yet remains

readily accessible.

9 Mains Input

Use the factory-included locking power cord to con-

nect this socket to a mains outlet. The catch holds

the cord in place, preventing accidental unplugging.

You must release the yellow catch on the bottom of

the plug before you can unplug the cord.

Note: This socket also accepts a standard Euro

mains cable, but it will not lock it in place.

2.2 Setting Up and Connecting

the Cabinet

Connect cords routed from your mixer (monitor

out, line out, or a similar output) to the balan-

ced Input sockets using a cord equipped with

standard XLR microphone connectors. Then

connect the active satellites to the XLR outputs

labeled X-Over Out. Use the two Through ports

to feed the fullrange signal to other enclosures.

Make sure the XLR connectors’ terminals are

configured as follows: 1= ground, 2= +, 3= -. If

only one Input signal is available, select “Input

L”. To get full power out of the system, connect

“Through L” with “Input R” via XLR cords.

2.3 Operating Speakers

• First make sure the powered cabinet is off.

CAUTION! Connect the cabinet to the mains

supply only after you are certain the local

mains voltage matches the voltage specified

on the rear panel. If you connect the system to

the wrong mains voltage, you may destroy the

electronic components of the PREMIUM PR:O

active cabinet.

• Back the Gain knobs all the way off, turning

them counterclockwise as far as they will go.

Ensure you first switch on all other connected

components, for example, a connected mixing

console as well as all signal sources patched

into it, such as keyboards, instrument amps,

effects and so forth. Always connect PREMIUM

PR:O active cabinets to Line Out Mid/High,

and always switch them on last; that is, after

you switch on all other connected components.

When you powering down, first turn the Gain

knobs to the far left and switch active cabinets

off first, before switching off any connected

devices.

After you power the system up by engaging the

Power switch, a system check prompts the fan

to briefly kick on and back off again in about

five seconds. The fan is temperature-controlled,

actuating only at very high volumes and tempe-

ratures requiring cooling.

• The Power LED lights up green when the cabi-

net receives mains power.

Set the Gain Line In knob to the center or 12

o’clock position (= 0 dBV). This is the preferred

level if you have connected a mixer to the PRE-

MIUM PR:O active cabinet. You can boost the

input level 6 dB by turning up the Gain knob

For the best audio results, ensure the Limiter

LED (red) does not light up continuously.

2.4 Settings

Adjusting volume with the Gain knob

Twist this knob to adjust microphone and line

signal levels.

CAUTION: Never tape over the plug’s ground

terminal – this endangers lives!

If you hear distortion or saturated signals, first

check the signal sources and, if possible, red-

uce the output signal level there. If you cannot

adjust the level of the signal routed to the PRE-

MIUM PR:O active cabinet at the source, match

it to the power amps by backing off the Gain

knob to lower the input level.

English

PREMIUM PR:O Active 1.4

3 Tips and Tricks

1 Do not expose electronic circuitry to moisture!

Protect cabinets against rain when you set them

up outdoors. Keep soft drinks, beer, and any other

liquids away from the electronic components to

prevent short circuits.

2 PREMIUM PR:O active enclosures provide opti-

mum sound to you, so be sure to provide optimum

input signals to them! Noise such as humming is

generally caused by defective cables, the wrong

type of cords, or unbalanced signals routed into the

mixing console. Check all signal and mains cables.

3 Prevent distortion! Not only is it unpleasant to your

audience’s ears, it also endangers your equipment.

Make sure all components that are connected

directly and indirectly to PREMIUM PR:O active

cabinets have sufficient power ratings, and that

they don’t distort because they‘re running at their

respective limits. Ensure all sources deliver clean

audio signals.

4 Avoid ground loops! Annoying humming can arise

even within audio systems with balanced circuits,

for example, when the mixing console’s mains cord

isn’t connected and grounded to the same mains

circuit as PREMIUM PR:O active enclosures. Using

two different ground circuits can create a ground

loop. To prevent this problem, always connect

PREMIUM PR:O active enclosures and the mixing

console to the same electrical circuit; that is, the

same phase!

CAUTION: Never tape over the plug’s ground

terminal - this endangers lives!

4 Troubleshooting

The POWER LED does not light up when switched

on.

• Check if the mains cord is plugged into the Mains

Input.

• Check if the mains power supply is providing

current.

The Power LED lights up red, flashing intermittently.

• The Limiter has actuated; lower the input level if

necessary.

The Power LED lights up red continuously, but no

sound is issuing from the cabinet.

• The enclosure’s protective circuit has tripped.

Please contact your authorized dealer.

The rendered music sounds distorted.

• Check your mixing console’s LED meters. They

should not be constantly in the red. If necessary,

back off the volume at the mixer.

• If the LED displays on your mixer are in the green,

back off the PREMIUM PR:O active cabinet’s Gain

knob.

• Observe the Limiter LEDs on the PREMIUM PR:O

active enclosure’s control panel. These may light up

red, but only intermittently. The red light may not

illuminate continuously. If it does, turn down the

Gain knob.

This is to certify that

PR:O 8 A, PR:O 10 XA,

PR:O 12 A, PR:O 12 MA,

PR:O 15 A, PR:O 15 XA,

PR:O 18 Sub A, PR:O 210 Sub A

complies with the provisions of the Directive of the

Council of the European Communities on the appro-

ximation of the laws of the Member States relating to

electromagnetic compatibility according to EMC directive

2004/108/EC and low voltage directive 2006/95/EC.

This declaration of conformity of the European Com-

munities is the result of an examination carried out by

the Quality Assurance Department of STAMER GmbH

in accordance with European Standards EN61000-6-1,

EN61000-6-2, and EN 60065 for low voltage.

Magdeburger Str. 8, 66606 St. Wendel

Lothar Stamer Dipl.Ing.

Managing Director

St. Wendel, 01/08/2008

Version 2.0 08/2008

PREMIUM PR:O active System Configurations

2 x PR:O 8 A or

2 x PR:O 10 XA or

2 x PR:O 12 A or

2 x PR:O 15 A or

2 x PRO 15 XA

2 x PR:O 8 A or

2 x PR:O 10 XA or

2 x PR:O 12 A or

2 x PR:O 15 A

+ 2 x PR:O 18/210 Sub A

PR:O 8 A + PR:O 8 or

PR:O 10 XA + PR:O 10 XA or

PR:O 12 A + PR:O 12 or

PR:O 15 A + PR:O 15 or

PR:O 15 XA + PR:O 15 X

PR:O 10 XA + PR:O 10 X

PR:O 12 MA + PR:O 12 M

active, stereo active/passive, mono

Monitoring

Systems

4 x PR:O 8 A

+ 2 x PR:O 210 Sub A

4 x PR:O 8 A

+ 2 x PR:O 18 Sub A

English

5 Technical Data

PR:O 8 A PR:O 10 XA PR:O 12 A PR:O 12 MA PR:O 15 A PR:O 15 XA PR:O 18 Sub A PR:O 210 Sub A

Frequency response +/- 3dB: 89 Hz - 19 kHz 89 Hz - 19 kHz 85 Hz - 19 kHz 85 Hz - 19 kHz 55 Hz - 19 kHz 55 Hz - 19 kHz 48 Hz – fx 60 Hz – fx

Frequency response -10 dB: 63 Hz - 19 kHz 67 Hz - 19 kHz 78 Hz - 19 kHz 78 Hz - 19 kHz 48 Hz - 19 kHz 48 Hz - 19 kHz 38 Hz – fx 40 Hz – fx

Max SPL (Half Space): 118 dB 121 dB 123 dB 123 dB 123 dB 123 dB 125 dB 123 dB

Loudspeakers:

Bass / midrange woofer 8" 10" 12" 12" 15" 15" 18" 2x 10"

High-frequency driver 1" 1" 1" 1" 1" 1" - -

HF protection (passive): Dyn. protective circuit Dyn. protective circuit Dyn. protective circuit Dyn. protective circuit Dyn. protective circuit Dyn. protective circuit Dyn. protective circuit Dyn. prot. circuit

Horn directivity: 80° x 80 CD horn 90° x 60 CD horn 60° x 40 CD horn 60° x 40° CD horn 60° x 40° CD horn 60° x 40° CD horn - -

Power amps: 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 Watt 1x 600 Watt

Class D - 4 ohms Class D - 4 ohms Class D - 4 ohms Class D - 4 ohms Class D - 4 ohms Class D - 4 ohms Class D - 4 ohms Class D - 4 ohms

Limiters:

RMS Limiter yes yes yes yes yes yes no no

Peak Limiter yes yes yes yes yes yes no no

Subsonic Filter: 35 Hz 35 Hz 35 Hz 68 Hz 35 Hz 35 Hz 35 Hz 35 Hz

Cutoff frequency - - - - - - 75 - 150 Hz variable 75 - 150 Hz variable

of the active crossover

(12 dB/ octave)

EQ: Tone knob Tone knob Tone knob - Tone knob Tone knob - -

Connectors:

Line/Mic combi jack: 1x combi XLR/1/4" 1x combi XLR/1/4" 1x combi XLR/1/4" 1x combi XLR/1/4" 1x combi XLR/1/4" 1x combi XLR/1/4" 2x 1x combi XLR/1/4" 2x 1x combi XLR/1/4"

balanced

Through, balanced: 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 2x XLR Through 2x XLR Through

Out, balanced: - - - - - - 2x XLR L/R Out Mid/High 2x XLR L/R Out Mid/High

Parallel Speaker Out* 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon - -

Pole mount: MonoTilt™ DuoTilt 3/7 DuoTilt 3/7 - DuoTilt 3/7 DuoTilt 3/7 M20 threaded base plate 2x M20 thread. base plate

Rigging points: 2x M8 3x M8 3x M8 3x M8 3x M8 3x M8 - -

Weight: 11 kg / 24.3 lbs. 13,9 kg / 30.6 lbs. 19,5 kg / 43 lbs. 17,1 kg / 37,7 lbs. 23,5 kg / 51,8 lbs. 22,4 kg / 49,4 lbs. 39,8 kg / 87,8 lbs. 27,2 kg / 55 lbs.

Dimensions (WxHxD) 27 x 42 x 27 cm 32 x 48 x 29 cm 39 x 57 x 36 cm 39 x 55,5 x 38 cm 47 x 61,5 x 41,5 cm 47 x 61,5 x 44,5 cm 53 x 61 x 64 cm 36 x 61 x 53 cm

*) Min impedance 8 ohm/300 W

Page is loading ...

Deutsch

5 Technische Daten

Bezeichnung PR:O 8 A PR:O 10 XA PR:O 12 A PR:O 12 MA PR:O 15 A PR:O 15 XA PR:O 18 Sub A PR:O 210 Sub A

Frequenzgang +/- 3dB: 89 Hz - 19 kHz 89 Hz - 19 kHz 85 Hz - 19 kHz 85 Hz - 19 kHz 55 Hz - 19 kHz 55 Hz - 19 kHz 48 Hz - fx 60 Hz - fx

Frequenzgang -10 dB: 63 Hz - 19 kHz 67 Hz - 19 kHz 78 Hz - 19 kHz 78 Hz - 19 kHz 48 Hz - 19 kHz 48 Hz - 19 kHz 38 Hz - fx 40 Hz - fx

Max SPL (Half Space): 118 dB 121 dB 123 dB 123 dB 123 dB 123 dB 125 dB 123 dB

Lautsprecher:

Bass / Mid: 8" 10" 12" 12" 15" 15" 18" 2x 10"

Hochtontreiber: 1" 1" 1" 1" 1" 1" -

Hochtonschutz (passiv): Dyn. Schutzschaltung Dyn. Schutzschaltung Dyn. Schutzschaltung Dyn. Schutzschaltung Dyn. Schutzschaltung Dyn. Schutzschaltung Dyn. Schutzschaltung Dyn. Schutzschaltung

Horncharakteristik: 80° x 80 CD Horn 90° x 60° CD Horn 60° x 40 CD Horn 60° x 40° CD Horn 60° x 40° CD Horn 60° x 40° CD Horn - -

Endstufen: 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt

Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm

Limiter:

RMS- Soundlimiter: ja ja ja ja ja ja nein nein

Peak Schutzlimiter: ja ja ja ja ja ja ja ja

Subsonic Filter: 35 Hz 35 Hz 35 Hz 68 Hz 35 Hz 35 Hz ja ja

Trennfrequenz - - - - - - 75–150 Hz wählbar 75–150 Hz wählbar

der aktiven Weiche:

(12 dB Oktave)

Klangregelung: Tone Regler Tone Regler Tone Regler - Tone Regler Tone Regler - -

Anschlüsse:

Line/Mic Kombibuchse: 1x Kombi Line In 1x Kombi Line In 1x Kombi Line In 1x Kombi Line In 1x Kombi Line In 1x Kombi Line In 2x Kombi Line In 2x Kombi Line In

symmetrisch

Through, symmetrisch: 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 2x XLR Through 2x XLR Through

Out, symmetrisch: - - - - - - 2x XLR L/R Out Mid/High 2x XLR L/R Out Mid/High

Parallel Speaker Out* 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon - -

Hochständerflansch: MonoTilt™ DuoTilt 3/7 DuoTilt 3/7 - DuoTilt 3/7 DuoTilt 3/7 M20 2x M20

Flugpunkte: 2x M8 3x M8 3x M8 3x M8 3x M8 3x M8 - -

Gewicht: 11 kg / 24.3 lbs. 13,9 kg / 30.6 lbs. 19,5 kg / 43 lbs. 17,1 kg / 37,7 lbs. 23,5 kg / 51,8 lbs. 22,4 kg / 49,4 lbs. 39,8 kg / 87,8 lbs. 27,2 kg / 55 lbs.

Maße (BxHxT): 27 x 42 x 27 cm 32 x 48 x 29 cm 39 x 57 x 36 cm 39 x 55,5 x 38 cm 47 x 61,5 x 41,5 cm 47 x 61,5 x 44,5 cm 53 x 61 x 64 cm 36 x 61 x 53 cm

*) Min impedance 8 Ohm/300 Watt

Page is loading ...

5 Caractéristiques techniques

Description PR:O 8 A PR:O 10 XA PR:O 12 A PR:O 12 MA PR:O 15 A PR:O 15 XA PR:O 18 Sub A PR:O 210 Sub A

Réponse en fréq. +/- 3dB: 89 Hz - 19 kHz 89 Hz - 19 kHz 85 Hz - 19 kHz 85 Hz - 19 kHz 55 Hz - 19 kHz 55 Hz - 19 kHz 48 Hz - fx 60 Hz - fx

Réponse en fréq. -10 dB: 63 Hz - 19 kHz 67 Hz - 19 kHz 78 Hz - 19 kHz 78 Hz - 19 kHz 48 Hz - 19 kHz 48 Hz - 19 kHz 38 Hz - fx 40 Hz - fx

SPL maxi (Half Space): 118 dB 121 dB 123 dB 123 dB 123 dB 123 dB 125 dB 123 dB

Hauts-parleurs :

Basses / Médiums : 8" 10" 12" 12" 15" 15" 18" 2x 10"

Haut-parleur d’aigus : 1" 1" 1" 1" 1" 1" - -

Protection (passive) : Circuit de prot. dyn. Circuit de prot. dyn. Circuit de prot. dynam. Circuit de prot. dynam. Circuit de prot. dynam. Circuit de prot. dynam. Circuit de prot. dynam. Circuit de prot. dynam.

contre les suraigus

Caractéristique de pavillon : CD 80° x 80° CD 90° x 60° CD 60° x 40° CD 60° x 40° CD 60° x 40° CD 60° x 40° - -

Étages de puissance : 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 W 1x 600 W

classe D - 4 ohms classe D - 4 ohms classe D - 4 ohms classe D - 4 ohms classe D - 4 ohms classe D - 4 ohms classe D - 4 ohms classe D - 4 ohms

Limiteur :

Limiteur de son RMS : oui oui oui oui oui oui non non

Limit. de prot. de crêtes : oui oui oui oui oui oui oui oui

Filtre Subsonic : 35 Hz 35 Hz 35 Hz 68 Hz 35 Hz 35 Hz 35 Hz 35 Hz

Fréq. de coupure - - - - - - 75 - 150 Hz, réglable 75 - 150 Hz, réglable

du branchement actif :

(12 dB / octave)

Réglage du son : Potentiomètre Tone Potentiomètre Tone - Potentiomètre Tone Potentiomètre Tone Potentiomètre Tone - -

Connexions :

Line/Mic In: 1x douille XLR comb. 1x douille XLR comb. 1x douille XLR comb. 1x douille XLR comb. 1x douille XLR comb. 1x douille XLR comb. 2x douille XLR comb. 2x douille XLR comb.

symétrisée

Through, symétrisée : 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 2x XLR Through 2x XLR Through

Out, symétrisée : - - - - - - 2x XLR L/R Out Mid/High 2x XLR L/R Out Mid/High

Parallel Speaker Out* 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon - -

Embase pied d’enceinte : MonoTilt™ DuoTilt 3/7 DuoTilt 3/7 - DuoTilt 3/7 DuoTilt 3/7 Plateau fileté M20 2x Plateau fileté M20

Points de fixation : 2x M8 3x M8 3x M8 3x M8 3x M8 3x M8 - -

Poids : 11 kg / 24.3 lbs. 13,9 kg / 30.6 lbs. 19,5 kg / 43 lbs. 17,1 kg / 37,7 lbs. 23,5 kg / 51,8 lbs. 22,4 kg / 49,4 lbs. 39,8 kg / 87,8 lbs. 27,2 kg / 55 lbs.

Dimensions (l x H x P) : 27 x 42 x 27 cm 32 x 48 x 29 cm 39 x 57 x 36 cm 39 x 55,5 x 38 cm 47 x 61,5 x 41,5 cm 47 x 61,5 x 44,5 cm 53 x 61 x 64 cm 36 x 61 x 53 cm

*) impédance mini 8 ohms, 300 watts

Français

Page is loading ...

Español

5 Datos técnicos

Denominación PR:O 8 A PR:O 10 XA PR:O 12 A PR:O 12 MA PR:O 15 A PR:O 15 XA PR:O 18 Sub A PR:O 210 Sub A

Respuesta de frecuencia:

+/- 3dB: 89 Hz - 19 kHz 89 Hz - 19 kHz 85 Hz - 19 kHz 85 Hz - 19 kHz 55 Hz - 19 kHz 55 Hz - 19 kHz 48 Hz - fx 60 Hz - fx

-10 dB: 63 Hz - 19 kHz 67 Hz - 19 kHz 78 Hz - 19 kHz 78 Hz - 19 kHz 48 Hz - 19 kHz 48 Hz - 19 kHz 38 Hz - fx 40 Hz - fx

Max SPL (medio espacio): 118 dB 121 dB 123 dB 123 dB 123 dB 123 dB 125 dB 123 dB

Altavoces:

Bass / Mid: 8" 10" 12" 12" 15" 15" 18" 2x 10"

Driver de agudos: 1" 1" 1" 1" 1" 1" - -

Protección de tonos agudos:

(pasiva) Circuito protector Dyn Circuito protector Dyn Circuito protector Dyn Circuito protector Dyn Circuito protector Dyn Circuito protector Dyn Circuito protector Dyn Circuito protector Dyn

Característica de bocina: 80° x 80 CD bocina 90° x 60° CD bocina 60° x 40 CD bocina 60° x 40° CD bocina 60° x 40° CD bocina 60° x 40° CD bocina - -

Etapas finales: 1x 600 vatios 1x 600 vatios 1x 600 vatios 1x 600 vatios 1x 600 vatios 1x 600 vatios 1x 600 vatios 1x 600 vatios

Class D - 4 Ohmios Class D - 4 Ohmios Class D - 4 Ohmios Class D - 4 Ohmios Class D - 4 Ohmios Class D - 4 Ohmios Class D - 4 Ohmios Class D - 4 Ohmios

Limitador:

Limitador de sonido RMS: si si si si si si no no

Limitador protector de picos: si si si si si si si si

Filtro subsónico: 35 Hz 35 Hz 35 Hz 68 Hz 35 Hz 35 Hz 35 Hz 35 Hz

Frecuencia de separación - - - - - - 75-150 Hz seleccionable 75-150 Hz seleccionable

de crossover: (12 dB octavo)

Regulación de sonido: Regulador de tonos Regulador de tonos Regulador de tonos - Regulador de tonos Regulador de tonos - -

Conexiones:

Line/Mic In: 1x Con.hembra combin. 1x Con.hembra combin. 1x Con.hembra combin. 1x Con.hembra combin. 1x Con.hembra combin. 1x Con.hembra combin. 2x Con.hembra combin. 2x Con.hembra combin.

simétrica

Through, simétrica: 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 2x XLR Through 2x XLR Through

Out, simétrica: - - - - - - 2x XLR L/R Out Mid/High 2x XLR L/R Out Mid/High

Parallel Speaker Out* 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon - -

Brida para soporte en altura: MonoTilt™ DuoTilt 3/7 DuoTilt 3/7 - DuoTilt 3/7 DuoTilt 3/7 Brida roscada M20 2x Brida roscada M20

Puntos de sujeción 2x M8 3x M8 3x M8 3x M8 3x M8 3x M8 - -

Peso: 11 kg / 24.3 lbs. 13,9 kg / 30.6 lbs. 19,5 kg / 43 lbs. 17,1 kg / 37,7 lbs. 23,5 kg / 51,8 lbs. 22,4 kg / 49,4 lbs. 39,8 kg / 87,8 lbs. 27,2 kg / 55 lbs.

Dimensiones (axAxP): 27 x 42 x 27 cm 32 x 48 x 29 cm 39 x 57 x 36 cm 39 x 55,5 x 38 cm 47 x 61,5 x 41,5 cm 47 x 61,5 x 44,5 cm 53 x 61 x 64 cm 36 x 61 x 53 cm

*) impedancia 8 Ohmios, 300 Vatios

Page is loading ...

Italiano

5 Caratteristiche tecniche

Tipo PR:O 8 A PR:O 10 XA PR:O 12 A PR:O 12 MA PR:O 15 A PR:O 15 XA PR:O 18 Sub A PR:O 210 Sub A

Risposta in freq. +/- 3dB: 89 Hz - 19 kHz 89 Hz - 19 kHz 85 Hz - 19 kHz 85 Hz - 19 kHz 55 Hz - 19 kHz 55 Hz - 19 kHz 48 Hz - fx 60 Hz - fx

Risposta in freq. -10 dB: 63 Hz - 19 kHz 67 Hz - 19 kHz 78 Hz - 19 kHz 78 Hz - 19 kHz 48 Hz - 19 kHz 48 Hz - 19 kHz 38 Hz - fx 40 Hz - fx

Max SPL (Half Space): 118 dB 121 dB 123 dB 123 dB 123 dB 123 dB 125 dB 123 dB

Altoparlanti:

Bass / Mid: 8" 10" 12" 12" 15" 15" 18" 2x 10"

Driver acuti: 1" 1" 1" 1" 1" 1" - -

Protezione (passiva): Circuito di prot. din. Circuito di prot. din. Circuito di prot. din. Circuito di prot. din. Circuito di prot. din. Circuito di prot. din. Circuito di prot. din. Circuito di prot. din.

Caratteristiche della tromba: 80° x 80 tromba CD 90° x 60 tromba CD 60° x 40 tromba CD 60° x 40° tromba CD 60° x 40° tromba CD 60° x 40° tromba CD - -

Sezione finale di potenza: 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt 1x 600 Watt

Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm Class D - 4 Ohm

Limiter:

RMS- Soundlimiter: si si si si si si no no

Peak Schutzlimiter: si si si si si si si si

Filtro subsonic: 35 Hz 35 Hz 35 Hz 68 Hz 35 Hz 35 Hz 35 Hz 35 Hz

Frequenza di separazione - - - - - - 75 – 150 Hz regolabile 75 – 150 Hz regolabile

del filtro divisore attivo:

(12 dB/Ottava)

Regolazione di tonalità: controllo Tone controllo Tone controllo Tone - controllo Tone controllo Tone - -

Collegamenti:

Line/Mic In: 1x presa combinata 1x presa combinata 1x presa combinata 1x presa combinata 1x presa combinata 1x presa combinata 2x presa combinata 2x presa combinata

simmetrico

Through, simmetrico: 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 1x XLR Through 2x XLR Through 2x XLR Through

Out, simmetrico: - - - - - - 2x XLR L/R Out Mid/High 2x XLR L/R Out Mid/

High

Parallel Speaker Out* 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon 1x Speakon - -

Flangia di supporto: MonoTilt™ DuoTilt 3/7 DuoTilt 3/7 - DuoTilt 3/7 DuoTilt 3/7 flangia filettata M20 2x flangia filettata M20

Punti da rigging: 2x M8 3x M8 3x M8 3x M8 3x M8 3x M8 - -

Peso: 11 kg / 24.3 lbs. 13,9 kg / 30.6 lbs. 19,5 kg / 43 lbs. 17,1 kg / 37,7 lbs. 23,5 kg / 51,8 lbs. 22,4 kg / 49,4 lbs. 39,8 kg / 87,8 lbs. 27,2 kg / 55 lbs.

Dimensioni (LxAxP): 27 x 42 x 27 cm 32 x 48 x 29 cm 39 x 57 x 36 cm 39 x 55,5 x 38 cm 47 x 61,5 x 41,5 cm 47 x 61,5 x 44,5 cm 53 x 61 x 64 cm 36 x 61 x 53 cm

*) Min impedance 8 Ohm, 300 Watt