NEC NP01TM Installation guide

NP01TM

Installation Manual

English

Deutsch

Français

Italiano

Español

Português

Русский

Türkçe

Polski

한글

日本語

Touch Module

Page is loading ...

Touch Module

NP01TM

Installation Manual

CONTENTS

Introduction

.......................................................................................................... 2

Disposing of your used product

...................................................................... 2

Read This Before Starting

............................................................................... 4

Location to Mount the Touch Module and Mounting Procedure

..... 6

1. Packaged Items

............................................................................................. 7

2. Parts Names

.................................................................................................... 7

Front face

........................................................................................................... 7

Cover Inside

....................................................................................................... 8

Rear Face

.......................................................................................................... 8

3. Setup Procedure

............................................................................................ 9

4. Download the Software Program

............................................................ 9

5. Mount the Touch Module at the Top of the Screen

........................ 10

6. Connecting the USB Cable

..................................................................... 12

7. How to Use the Antireﬂection Sheet

.................................................... 13

8. Speciﬁcations

............................................................................................... 14

ENG-2

Introduction

Thank you for purchasing the NEC Touch Module, NP01TM, hereinafter called the touch mod-

ule or this product in this manual.

By connecting this product to an NEC projector in combined use with an interactive white

board kit, it enables to draw on a screen by fingers instead of using a stylus pen.

Finger touch operation can not be carried on only by this product in independent use.

Make sure to use this product in combined use with the interactive whiteboard kit (camera unit).

Supported interactive whiteboard kit (as of Feb. 2015)

NP03Wi

Supported projectors (as of Feb. 2015)

NP-M352WS, NP-M302WS, NP-M332XS,

NP-UM351W, NP-UM301W, NP-UM361X, NP-UM301X,

NP-UM280X, NP-UM330X, NP-UM280W, NP-UM330W

Disposing of your used product

EU-wide legislation as implemented in each Member State requires that used electrical and

electronic products carrying the mark (left) must be disposed of separately from normal

household waste. When you dispose of such products, please follow the guidance of your

local authority and/or ask the shop where you purchased the product.

After collecting the used products, they are reused and recycled in a proper way. This effort

will help us reduce the wastes as well as the negative impact such as mercury contained in

parts to the human health and the environment at the minimum level.

The mark on the electrical and electronic products only applies to the current European

Union Member States.

Products and company names mentioned in this installation manual may be the trademarks or regis-

tered trademarks of their respective holders.

Note:

(1) Unauthorized reprinting of the contents of this manual is prohibited.

(2) The contents of this manual are subject to change in the future without notice.

(3) The contents of this manual have been prepared with scrupulous care, but please notify

NEC should you have any doubts or notice any mistakes or omissions.

(4) Please note that NEC will accept no responsibility whatsoever for claims for damages, lost

earnings, etc., arising from the use of this product, regardless of article (3) above.

(5) NEC will replace any manuals presenting incorrect collation or missing pages.

ENG-3

DOC Compliance Notice (for Canada only)

This Class B digital apparatus complies with Canadian ICES-003.

RF Interference (for USA only)

WARNING

The Federal Communications Commission does not allow any modiﬁcations or changes to the

unit EXCEPT those speciﬁed by NEC Display Solutions of America, Inc. in this manual. Failure

to comply with this government regulation could void your right to operate this equipment. This

equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connectthe equipment intoanoutletona circuitdifferentfromthattowhichthe receiveris

connected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

WARNING TO CALIFORNIA RESIDENTS:

Handlingthecables suppliedwith this productwill exposeyou to lead,a chemical known to

the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER

HANDLING.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions. (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

U.S.Responsible Party: NEC Display Solutions of America, Inc.

Address: 500 Park Boulevard, Suite 1100

Itasca, Illinois 60143-1248

Tel. No.: (630) 467-3000

Type of Product: Touch Module

Equipment Classiﬁcation: Class B Peripheral

Model No.: NP01TM

We hereby declare that the equipment speciﬁed above conforms to the technical

standards as speciﬁed in the FCC Rules.

ENG-4

Read This Before Starting

About the pictograms

To ensure safe and proper use of the product, this installation manual uses a number of picto-

grams to prevent injury to you and others as well as damage to property.

The pictograms and their meanings are described below. Be sure to understand them thor-

oughly before reading this manual.

WARNING

Failing to heed this pictogram and handling the product errone-

ously could result in accidents leading to death or major injury.

CAUTION

Failing to heed this pictogram and handling the product errone-

ously could result in personal injury or damage to surrounding

property.

Examples of pictograms

The



symbol indicates instructions urging caution (including warnings). A con-

crete indication of the caution is given within the symbol.

The symbol indicates prohibited actions. A concrete indication of the prohib-

ited action is given within the symbol.

The



symbol indicates required actions. A concrete indication of the required

action is given within the symbol.

WARNING

Laser Safety Caution

• Laserdiodeissealedinthisproduct.Useofcontrolsoradjustmentsofproce-

dures other than those specified herein may result in hazardous radiation expo-

sure.

• ThisproductisclassifiedasClass1ofIEC60825-1:2007.

• ThecautionandexplanatorylabelsoftheCLASS1LASERPRODUCTSisonthe

side face of this product body.

24L80101

ENG-5

WARNING

• Donotlookintothelaserdiffusionpartwhilethetouchmoduleison.Serious

damage to your eyes could result.

• Thefollowingcautionpictogramisindicatednearthelaserdiffusionpart.

• Keepanyopticalitems(aloupe,areflectingmirror,etc.)outoftheprojection

screen area. Visual impairment could result.

• Donotremoveanyscrewsbesidesthespecifiedscrewsinthisinstallation

manual for mounting /demounting this product.

• Donotdisassembleandremodel.Donotsubjectthisproducttoshockorex-

cessive forces. It may cause of fire, shock and laser light leakage.

Contact your dealer for the inspection, adjustment and repair.

• Donotplacethisproductindampplace.Avoiddrippingorsplashingwater

near this product. If water has been spilled into this product, contact your

dealer.

• Donotinsertanymetalorflammableobjects.Itmaycauseoffireandshock.

Pay enough attention to children. If something should fall into this product,

disconnect the USB cable connecting with the projector and contact your

dealer.

• ThepowerforthisproductissuppliedfromtheUSBportonthesupported

projector via the USB cable supplied with this product.

Wrong connection may cause of fire and shock.

CAUTION

• Ifthetouchmoduleismountedwiththebuilt-inmagnets,takeappropriate

countermeasure from falling down. If not, the touch module may fall down and

may cause of injury.

Take security measure by an item supports the MicroSaver® security system.

ENG-6

Location to Mount the Touch Module and Mounting Procedure

• Thetouchmoduleisnotusedoutdoorandintheareadirectsunlightorstronglightstrikes

the screen surface. Operation in bright circumstance as beside a window, near a fi lament

lamp, or a halogen lamp issues much infrared light may cause of malfunction.

• Mountthetouchmoduleontoascreenofwhichsurfacedeflectioniswithin8mm.For

smooth operations, recommend to use a screen which surface defl ection is within 3mm.

• Thetouchmoduleusablescreensizeisfrom60”to100”.

• Forusingthetouchmodule,installtheprojectorbyawallmountunit,aceilingmountunit,

or a table mount unit. If the projector installed on a desktop, the touch module cannot be

used.

• Mountthetouchmoduleatthepositionasthebelowillustrationconsideringtheimagepro-

jection area.

Touch module

Over 100 mm / 4 inches

Screen

Projection area

Over 25 mm / 1 inch

25mm - 100mm

*

/ 1 - 4 inches

* Pay attention to mount not to cut into the projection light.

• Forsecuringthetouchmodule,usethebuilt-inmagnetorcommerciallyavailablescrews.

• Forusingcommerciallyavailablescrews,preparetwo(2)boltsofwhichnominaldiameteris

3mm. Choose an appropriate bolt to your circumstances.

ENG-7

1. Packaged Items

Makesureyourboxcontainseverythinglisted.Ifanypiecesaremissing,contactyourdealer.

Touch Module

Mount at the top of a screen or a white board projected an image

by a projector.

USB cable (3.0 m / 118 inches) x 1 (*For power supply)7N520086

For connecting the USB port on the touch module (type B) and the

USB port on a projector (type A)

Antireﬂection sheet (Length 175 mm / 7 inches, 12 pcs)

For hiding bumps and obstructions around the screen that dis-

ables to draw utilizing the touch module.

Installation manual (this document)

2. Parts Names

Front face

Dial Cover

USB Port (type B) (*For power supply)

Power Indicator

Security Slot

Centering line

ENG-8

Cover Inside

Adjustment Dial A

Adjustment Dial B

CAUTION

• Whenthetouchmoduleismountedonascreenorawhiteboardbymagnets,holdthe

touch module and then remove the cover. Otherwise, the touch module may fall down and

may cause of injury.

Rear Face

Laser diffusion port

Magnet

Caution:

•Donottouchthelaserdiffusionports.Itmaycauseofmalfunction.

Note:

The security slot supports the MicroSaver® Security system.

ENG-9

3. Setup Procedure

STEP 1 Download and install the software program onto the computer.



STEP 2 Connect the interactive whiteboard kit to the projector for enable to use the stylus

pen.



STEP 3 Perform the calibration of the camera.



STEP 4 Mount the touch module at the top of the screen.



STEP 5 Connect the USB cable.



STEP 6 Perform the touch module adjustment.

Note:

• ConcerningtodetailsoftheSTEP1(Howtoinstallthesoftwareprogram),theSTEP3(How

to calibrate the camera), and the STEP6 (How to adjust the touch module), refer to the

software manual that is available from our company website.

4. Download the Software Program

Perform the calibration of the camera unit for the interactive whiteboard kit and adjustment of

the touch module for using the touch module.

The exclusive software program is available from our company website. Please visit our sup-

port site also about operational conditions as supported OS:

URL: http://www.nec-display.com/dl/en/index.html

PDF (Portable Document Format) explains the operations of camera calibration by the software

program and adjustment of the touch module is available. To view or print the PDF ﬁles Adobe

Reader

TM

is required.

ENG-10

5. Mount the Touch Module at the Top of the Screen

• Built-inmagnetsareloadedontherearfaceofthetouchmoduleasthefactorydefault

setting. No need to secure the touch module by screws on a screen or a white board that

attracts magnets.

• Forusingthetouchmoduleonascreenorawhiteboardthatdoesnotattractmagnets,

remove the built-in magnet from the rear face of the touch module and secure the touch

module with commercially available screws.

• Usecommerciallyavailablescrews(2pcs)innominaldiameter3mm.Prepareboltsthat

are appropriate for your circumstances.

• Projecttheadjustmentscreeninthesoftwareprogram.Thecenterpositionadjustmentline

would be displayed, Align this with the centering line on the touch module.

• Refertopage5aboutthetouchmodulemountingproceduresbythe tableprojection

mount unit.

Note:

• DonotconnecttheUSBcablebeforemountingthetouchmoduleontothescreen.

[1] Decide the position to mount the touch module referring the below picture.

Touch module

Over 25 mm / 1 inch

25mm - 100mm

*

/ 1 - 4 inches

Over 100 mm / 4 inches

Screen

Projection area

Over 25 mm / 1 inch

* Pay attention to mount not to cut into the projection light.

[2] Mount the touch module onto the screen.

Mounting by the built-in magnets

• Puttherearfaceofthetouchmoduleontoascreenorawhiteboardsincethetouchmodule

has built-in magnets on its rear face as the factory default setting.

• Incase,mountingthetouchmodulebythebuilt-inmagnets,takeappropriatecountermeasure

from falling down. Prepare the commercially available Kensington security wire and connect it

to the security slot on the touch module.

ENG-11

Mounting by commercially available screws

IMPORTANT

• Beforemountingthetouchmodulebycommerciallyavailablescrews,makesurethead-

justment of the touch module (hereinafter described) can be performed properly. Please

consider temporally mount until proper performance of adjustment can be checked. Take

preventivemeasurefromfallingdownforthetemporallymount,too.

• Utilizethemagnetsetholesformountingthetouchmodulebyscrews.

Remove the magnets from the touch module by a plus headed Phillips driver. Keep the removed

magnets and screws.

•

Mount the touch module onto a screen or a white board by commercially available screws.

Reference

• Forusingthetableprojectionmountunit,securethetouch

module by a commercially available double sided adhesive

tape sealed on the rear face of the touch module.

Prepare the double sided adhesive tape of which thick-

ness is in the range from 1.2 mm to 1.5 mm.

CAUTION

• Donotuseadoublesidedadhesivetapebesidesformountingthetouchmoduleona

table. It may cause of injury by fallen down touch module.

ENG-12

6. Connecting the USB Cable

Connect the USB port (type B) on the touch module and the USB port (type A) on the projector

by the USB cable supplied with the touch module.

• Makesuretheprojectorandthecomputerareconnectedbythecomputercable.

• MakesurethecameraunitandthecomputerareconnectedbytheUSBcable.(fortheoptional

interactive whiteboard kit)

Note:

• DonotconnecttotheUSBportontheprojectorforawirelessLANunit.

USB cable (for connecting with the touch module)

Projector

Camera unit

Screen or whiteboard

Touch module

USB Cable (for connecting with the interactive

whiteboard kit)

Computer cable

Computer

ENG-13

7. How to Use the Antireﬂection Sheet

Use the antireﬂection sheet supplied with the touch module when ﬁnger drawing is

disabled caused on reﬂection issued by an object laying at the bottom of a screen

such as a pen tray, a whiteboard or a screen frame, etc. Stick on the antireﬂection

sheet to cut the laser beam diffused by the touch module not to hit the reflection

caused object.

Note:

• Donotpeeloffthereflectionsheetonceit’sstuck.Repetitionofstickingonandoffwill

deteriorate the adhesive force of the sheet.

ENG-14

8. Speciﬁcations

Model name NP01TM

Laser class Class 1 (IEC60825-1:2007)

Internal laser diode Total laser power: 200 mW (

×

2 pcs)

Wavelength: 830 nm

Input terminal USB Type B x 1

Power requirement /

Nominal electric current

DC5V / 400 mA

Power consumption 2W

Weight 290 g / 0.64 lbs

External Dimensions 190(W)

•

74.5(D)

•

56.8 (H) (unit in mm) / 7.48(W)

•

2.93(D)

•

2.24(H) (unit in inch) (not including protrusion)

Effective range 60 to 100 inches

Operating temperature and

humidity

5° to 40°C (41° to 104°F) 20% to 80% (non-condensing)

Storage temperature and

humidity

-10° to 50°C (14° to 122°F ) 20% to 80% (noncondensing)

Page is loading ...

Turkish RoHS information relevant for Turkish market

EEE Yönetmeliğine Uygundur.

Ukrainian RoHS Information relevant for Ukrainian market

English

Declaration of Conformity

withtherequirementsofTechnicalRegulationontheRestrictionOftheuseofcertainHazardousSubstances

in Electrical and Electronic Equipment

(adopted by Order Nº 1057 of Cabinet of Ministers of Ukraine)

The Product is in conformity with the requirements of Technical Regulation on the Restriction Of the use of certain

HazardousSubstancesinelectricalandelectronicequipment(TRonRoHS).

ThecontentofhazardoussubstancewiththeexemptionoftheapplicationslistedintheAnnexNº2ofTRonRoHS:

1. Lead (Pb) – not over 0,1wt % or 1000wt ppm;

2. Cadmium (Cd) – not over 0,01wt % or 100wt ppm;

3. Mercury(Hg)–notover0,1wt%or1000wtppm;

4. Hexavalentchromium(Cr

6+

) – not over 0,1wt % or 1000wt ppm;

5. Polybrominated biphenyls (PBBs) – not over 0,1wt % or 1000wt ppm;

6. Polybrominated diphenyl ethers (PBDEs) – not over 0,1wt % or 1000wt ppm.

NEC Display Solutions, Ltd.

Ukrainian

Декларація про Відповідність

Вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в

електричному та електронному обладнанні

(затвердженого Постановою Nº 1057 Кабінету Міністрів України)

Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в елек-

тричному та електронному обладнанні (ТР ОВНР).

Вміст небезпечних речовин у випадках, не обумовлених в Додатку Nº 2 ТР ОВНР, :

1. свинець(Pb) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;

2. кадмій (Cd)– не перевищує 0,01 % ваги речовини або в концентрації до 100 частин на мільйон;

3. ртуть(Hg)–неперевищує0,1%вагиречовиниабовконцентраціїдо1000частиннамільйон;

4. шестивалентний хром (Cr

6+

) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на

мільйон;

5. полібромбіфеноли (PBB) – не перевищує 0,1% ваги речовини або в концентрації до 1000 частин на міль-

йон;

6. полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин

на мільйон.

NEC Display Solutions, Ltd.

Russian

Декларация о Соответствии

Требованиям Технического Регламента об Ограничении Использования некоторых Вредных Веществ в

электрическом и электронном оборудовании

(утверждённого Постановлением Nº 1057 Кабинета Министров Украины)

Изделие соответствует требованиям Технического Регламента об Ограничении Использования некоторых Вред-

ных Веществ в электрическом и электронном оборудовании (ТР ОИВВ).

Содержание вредных веществ в случаях, не предусмотренных Дополнением Nº 2 ТР ОИВВ:

1. свинец (Pb) – не превышает 0,1 % веса вещества или в концентрации до 1000 миллионных частей;

2. кадмий (Cd) – не превышает 0,01 % веса вещества или в концентрации до 100 миллионных частей;

3. ртуть(Hg)–непревышает0,1%весавеществаиливконцентрациидо1000миллионныхчастей;

4. шестивалентный хром (Cr

6+

) – не превышает 0,1 % веса вещества или в концентрации до 1000 миллион-

ных частей;

5. полибромбифенолы (PBB) – не превышает 0,1 % веса вещества или в концентрации до 1000 миллионных

частей;

6. полибромдифеноловые эфиры (PBDE) – не превышает 0,1 % веса вещества или в концентрации до 1000

миллионных частей.

NEC Display Solutions, Ltd.

Printed in China

In Europe

NEC Display Solutions Europe GmbH

Address: Landshuter Allee 12-14

D-80637 München, Germany

Telephone: +49 89 99699 0

Email: infomail@nec-displays.com

In North America

NEC Display Solutions of America, Inc.

Address: 500 Park Boulevard, Suite 1100

Itasca,

Illinois

60143, U.S.A.

Telephone: +1 800 836 0655

In Oceania

Australia

AWA Limited.

Address: 151 Arthur Street

Homebush West NSW 2140 Australia

Customer Call Centre

Telephone: 0297647777

Email Address: commercialsupport@awa.

com.au

New Zealand

Visual Group Ltd.

Address: 28 Walls Road Penrose Auckland

New Zealand

Telephone: 095250740

Email Address: sarah.reed@visualgroup.co.nz

In South America

Brazil

Videocorp Brasil

Address: Avenida Conselheiro Rodrigues

Alves Nro. 820 / Sala 15 - 2°

Andar - Vila Mariana

São Paulo - SP - Brasil

CEP 04014-002

Telefone: + 55-11-2924.2910 / + 55-11-

2924.2911

In Asia

NEC Display Solutions, Ltd.

Address: 686-1, Nishioi, Oi-Machi, Ashigaraka-

mi-Gun,

Kanagawa 258-8533, Japan

Telephone: +81 465 85 2369

NEC Solutions (China) Co.,Ltd.

Address: Rm 1903, Shining Building,35

Xueyuan Rd,

Haidian District Beijing 100191, P.R.C.

Telephone: +8610 59342706

NEC Hong Kong Ltd.

Address: 25/F.,The Metropolis Tower,10

Metropolis

Drive, Hunghom, Kowloon, Hong Kong

Telephone: +852 2369 0335

NEC Taiwan Ltd.

Address: 7F, No.167, SEC.2, Nan King East

Road,

Taipei, Taiwan, R.O.C.

Telephone: +886 2 8500 1710

NEC Asia Paciﬁc Pte Ltd.

Address: 401 Commonwealth Drive, #07-02,

Haw Par

Technocentre, Singapore 149598

Telephone: +65 6 799 6188

NEC Corporation of Malaysia Sdn. Bhd.

Address: 33rd Floor, Menara TA One, 22,

Jalan P.

Ramlee, 50250 Kuala Lumpur, Malaysia

Telephone: +6 03 2178 3600 (ISDN)

*7N8N5422*

NEC NP01TM Installation guide

NEC NP01TM Installation guide

in other languages

Related papers

Other documents