flir.com/security/pro
6.3”
159mm
6.3”
159mm
MODEL: N357V8
SERIES
QUICK START GUIDE
English Version 2.0
Compatible Accessories
FCC NoticeFCC Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
N357V8_QSG_EN_R2
For a full list of compatible accessories, visit
flir.com/security/cameramounts
Safety Precautions
• Use an appropriate low-voltage power cable to prevent fire or
electrical shock.
• Make sure to install the camera in an area that can support the
camera weight.
• There are no user-serviceable parts inside the camera. Do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Use
a soft cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for
submersion in water.
• Extend the Ethernet-cable run for your camera up to 300ft. You
can use an RJ45 coupler or network switch to connect male
ends of Ethernet cable together. A maximum of 3 connections is
recommended.
Weights & DimensionsWeights & Dimensions
4.7”
118mm
4.7”
118mm
2.0lbs / 0.9kg2.0lbs / 0.9kg
WeightWeight
8MP Motorized Varifocal
Network Vandal Dome Camera
Adjusting Zoom and Focus
A
B
Adjust the camera’s zoom and focus using an NVR, the web
interface, or on the camera. For more information, see your
NVR’s instruction manual on flir.com/security/pro.
NVR: Right-click on the camera’s live view and then
click AutoFocus. Use the sliders to adjust the zoom and
focus.
Web Interface: Use the controls in the right-hand panel
to adjust the zoom and focus.
C
Manual Zoom In/Out: Located on the camera base, press
W to zoom out and T to zoom in.
6.3” / 159mm6.3” / 159mm
Resources
Click on the Downloads tab
Visit flir.com/security/pro
Search for the model number
of your product
Click on your product in the
search results
4
3
2
1
Need Help?
Visit us online for up-to-date software and complete
instruction manuals
FLIR Systems, Inc., Copyright © 2017
As our products are subject to continuous improvement, FLIR Systems Inc. reserves the right to
modify product design, specifications and prices, without notice and without incurring any obligation.
E&OE
Package Contents
• 8MP Network Vandal Dome Camera
• 3× Mounting Screws & Drywall Anchors
• Security Screwdriver
• Mounting Template
Use the included security screw driver to loosen the
dome cover screws (3×). Remove the dome cover.
ATTENTION:
Test the camera prior to selecting a permanent mounting location by
temporarily connecting the camera(s) and cables to the NVR.
Installing the Camera
1
Use the included mounting template to mark holes for
the mounting screws.
2
3
4
5
6
7
Drill holes for the mounting screws. Use the included
drywall anchors if needed.
Connect the cables. See “Camera Connections Overview”
section for details. To ensure weatherproof installation,
when you are running the cable through the cable
conduit:
Attach the camera base to the mounting surface using
the included mounting screws (3×).
Mounting
screws (3×)
Drywall
anchors (3×)
Set the position and angle of the camera:
A) Rotate the camera around the base (rotates 360°
maximum).
B) Use a Phillips screwdriver to loosen the tilt
adjustment screws (2×]. Tilt the camera. Tighten
both screws when finished.
C) Adjust the position of the camera lens by twisting.
A
B
C
Replace the dome cover. Use the included security
screw driver to tighten the dome cover screws (3×).
ATTENTION:
Make sure IR LEDs are not blocked by the dome cover to prevent IR
reflection.
8
Remove the vinyl film from the dome cover.
Camera base
Camera Overview
A. IR LEDs
B. Light Sensor
C. Tilt Adjustment Screws (2×)
D. Reset Button: See “Resetting
the Camera” section for details.
E. microSD Card Slot: See
“Inserting the microSD Card”
section for details.
F. Manual Zoom In/Out: See
“Adjusting Zoom and Focus”
section for details.
Tilt adjustment
screws (2×)
Reset button
Resetting the Camera
1
2
Remove the dome cover. Make sure
the camera is powered on.
Press and hold the reset button for 5
seconds using a thin object to reset
the camera to default settings.
Inserting the microSD Card
1
2
Remove the dome cover.
Insert the microSD card
(not included) into the slot
until you hear a click.
microSD slot
NOTE: For details on configuring microSD recording, see the FLIR
IP Series Instruction Manual on this camera’s product page at
flir.com/security/pro.
For local recording, you can install a microSD card up to 128GB.
SanDisk™ or Kingston™ brand microSD cards recommended.
microSD card Class 10 supported.
L. Dome Cover
M. Dome Cover Screws (3×)
N357V8_QSG_EN_R2
A
B
C
D
E
F
H
J
K
G. For service purposes
only.
H. Audio I/O and Alarm
I/O Block
I. Cable Conduits (2×)
J. Ethernet Port (PoE):
PoE+ supported
(802.3at).
K. 12VDC / 24VAC Power
Input
L
M
I
A) Remove the cable conduit cap.
B) Run the cable through the cap.
C) Insert the cap back into the cable conduit. Use
silicone as needed.
G
Camera Connections Overview
Audio
Output
Audio
Input
Audio
(GND)
Alarm
Output
Alarm
(GND)
Alarm
Input
NOTE: Use junction box model S4JF6G for conduit
installation.
H
Use either of the two cable conduits to run cables through the
camera base.
Ethernet Port
PoE+ (802.3at)
J
12VDC/24VAC
Power (+)
12VDC/24VAC
Power (-)
K
*
NOTE: See “Camera Overview” section for details.
* If not using PoE, connect the camera to a 12VDC/24VAC
power source. See the rating label on the camera for minimum
power requirements.
ATTENTION:
You must connect the camera to a supporting H.265 NVR to take
advantage of H.265 compression. For more information, see your IP
camera’s instruction manual on flir.com/security/pro.
/
