Nieco Corporation 1424 Operating instructions

Brand: Nieco Corporation

Model: 1424

Category: Cookers

Type: Operating instructions

This manual is also suitable for

1124
824

AUTOMATIC

FOODSERVICE

EQUIPMENT

AUTOMATIC CHAR BROILER

MODEL 1424 GAS - “B” Series

OWNER’S MANUAL

IMPORTANT: RETAIN THIS MANUAL IN A SAFE PLACE

FOR FUTURE REFERENCE.

Broiler area must be kept free of combustible materials, and the flow of combustion and ventilation air must not

be obstructed. Operating personnel must not perform any maintenance or repair functions. Contact your Facilities

Maintenance Department.

In a prominent location, post instructions to be followed in the event the user smells gas. This information shall be

obtained by consulting your local gas supplier.

FOR YOUR SAFETY:

Do not store or use gasoline or other flammable vapors or liquids in

the vicinity of this or any other appliance.

WARNING: Improper installation, adjustment, alteration, maintenance

can cause property damage, injury, or death. Read the installation,

operating and maintenance instructions thoroughly before installing

or servicing this equipment.

TABLE OF CONTENTS

A. General Specifications.................................................................................................................2

B. Machine Installation.....................................................................................................................5

Pre-Installation

Mounting

Hood Requirements

Clearance

Gas Connection

Electrical Connection

Pre-Operation Check

Gas Connectors and Restraining Device

C. Operation ......................................................................................................................................8

Controls and Indicators

Gas System Controls

Step-by-Step Lighting Procedure

Shutdown Procedure

Automatic Temperature Control

ATC Temperatures

Broiler Set-up Chart

Bun Platen Adjustment

D. Assembly/Disassembly and Cleaning........................................................................................13

E. Conveyor Belt Removal...............................................................................................................17

F. Conveyor Belt Tension................................................................................................................18

Broil Belt Problems

G. Parts and Location.......................................................................................................................19

Model 1424

H. Trouble Shooting Guide ..............................................................................................................22

I. Wiring Diagrams...........................................................................................................................24

A. GENERAL SPECIFICATIONS

Model 1424 Gas

MODEL 1424 AUTOMATIC CHAR BROILER

Configured exclusively for the Carl’s Jr.

system, the Model 1424 includes accessories and

features that are proprietary and unique for

Carl's’ Jr. product needs.

MODEL 1424G SPECIFICATIONS:

• Single 22” broil belt

• Natural gas, propane, or electric

• Broil belt extension

• Extended product guides

• Enhanced bun grill speed

• Split bun platen

• 3” W.C Gas for low pressure

5” W.C. Gas for high pressure

• Automatic Temperature Control (ATC)

• #50 Main burner orifices

• 2:30 Cook time (approximate)

• Carl’s Jr. Chicken reverberators

OPTIONS:

• Carl’s Jr. Tubular stand (design for

Carl’s only)

AUTOMATIC CHAR BROILER

MODEL 1424G

THE STAR CHAR FOR CARL’S JR.

Model 1424G SPECIFICATION DRAWINGS

DIMENSIONS INCH MM

Length 44 1/4 1124

Height 29 7/32 742

Width 36 3/4 933

ENERGY - GAS MODELS

Gas Connection 3/4” N.P.T.

Electrical Connection (specify exact voltage)

Domestic 208-240Y120V 1Ø 50/60Hz 18A

Export 200-240V 1Ø 50/60Hz 18A

Avg. kW/hr 1.8

Natural Gas 3” W.C. 5” W.C.

BTU/hr 75,000 96,000

KCAL/hr 18,900 24,192

Liquid Propane 8” W.C. 11” W.C.

BTU/hr 82,000 96,000

KCAL/hr 20,664 24,192

WEIGHT LB KG

Shipping 525 240

EXHAUST CFM CMH

Typical 800 1360

NOTE - FOR ALTITUDE INSTALLATION ONLY: Equipment

installation at an altitude above 5,000 feet may require minor adjustments

depending upon the BTU content of incoming natural gas. Propane gas is

not recommended for units installed above 7,000 feet Electric is

recommended.

Model 1424G with Incendalyst

SPECIFICATION DRAWINGS

B. INSTALLATION

PRE-INSTALLATION

Uncrate the broiler, and inspect for shipping damage. Contact the factory if there is obvious damage.

Remove the tape securing the machine parts, and install the parts in their proper location. Refer to the

Parts and Location section of this manual. If you find concealed damage to any part of this unit, contact

your freight carrier immediately. The factory warranty does not cover freight damage.

MOUNTING

If the broiler was shipped with a tubular stand, refer to separate tubular stand assembly instructions.

Note: The four legs of the broiler stand are equipped with casters. Always set the brakes on the

casters to prevent the broiler from shifting during operation or cleaning.

LEVELING

Make sure that the broiler is level. Factory stands are equipped with adjustable casters.

HOOD REQUIREMENTS

This appliance must be installed under a ventilation hood of adequate size and capacity:

Model CFM CMH

1424 800 1360

The hood should be at least 6" (152MM) larger in all dimensions than the appliance top, and be 12" to

18" (305MM - 457MM) above the top. Do not obstruct the flow of combustion and ventilation air. An ade-

quate air supply must be available for safe and proper operation.

Note: See the National Fire Prevention Association booklet on ventilation of cooking equipment.

Write to: NFPA, 470 Atlantic Ave., Boston, MA 02210. Local codes on venting must also be com-

plied with.

CLEARANCE

For proper installation, the minimum clearance from combustible and non-combustible construction is 6"

(152MM) from the back and 6" (152MM) from the front of the machine. Keep appliance area free from

combustibles.

To facilitate disassembly and service of the unit a minimum of 24" (610MM) should be allowed on the

control panel (right) side of the broiler, as well as in front of the broiler.

GAS CONNECTION

At rated BTU capacity, the gas supply should deliver a pressure of at least 6" water column at the broiler

connection for natural gas, and 11" water column for propane gas. Incoming gas supply pressure must

not exceed 14" water column for either type of gas.

The appliance was shipped from the factory ready for gas supply hook-up to the shutoff valve under the

broiler. For disconnect, a manual valve must be located in the gas supply line upstream from the con-

necter.

If the machine is installed on a moveable stand; (1) the installation shall be made with a connector that

complies with the Standard for Connectors for Moveable Gas Appliances, ANSI Z21.69-1987, and

Addenda, Z21.6a-1989, and a quick disconnect device that complies with the Standard for Quick-

Disconnect Devices for Use With Gas Fuel, ANSI Z21.41-1989, and (2) adequate means must be provid-

ed to limit the movement of the appliance without depending on the connector and the quick-disconnect

device or its associated piping to limit the appliance movement. (See figures on page 6.)

Note: Appliance installation must conform with all local codes, or in the absence of local codes,

with the National Fuel Gas Code ANSI Z223.1-1988. Check all fittings for gas leaks, including

pilot tubing and inlet connections as soon as the appliance is connected to the gas supply.

Note: This appliance and its individual shutoff valve must be disconnected from the gas supply

piping system during any pressure testing of that system at test pressures in excess of 1/2 psig

(3.45 kPa).

Note: This appliance must be isolated from the gas supply piping system by closing its individual

manual shutoff valve during any pressure testing of the gas supply piping system at test pres-

sures equal to or less than 1/2 psig (3.45 kPa).

In Canada, installation shall be in accordance with CAN/CGA-B149.1 Natural Gas or CAN/CGA-B149.2

Propane Gas, and local codes where applicable.

By public initiative, the State of California has adopted legislation (Proposition 65) which requires manu-

facturers of many types of products, including gas appliances, to warn consumers of their products that

contain chemicals or produce substances listed by the State of California to either cause cancer, birth

defects, or other reproductive harm.

WARNING: If not installed, operated, and maintained in accordance with the manufacturer's

instructions, this product could expose you to substances in fuel, or from fuel combustion which

can cause cancer, birth defects, or other reproductive harm.

ELECTRICAL CONNECTION

Power requirements are stated on the unit nameplate and must be connected accordingly. Before start-

ing broiler, tighten all electrical connections in control box. An electrical diagram is located inside the con-

trol box.

Note: This appliance must be electrically grounded in accordance with local codes or in the

absence of local codes, the National Electrical Code, ANSI/NFPA No. 70-1990. In Canada, in

accordance with the Canadian Electrical Code CSA 22.1 part 1, or local codes.

WARNING: This appliance should be connected with a four-pronged grounding plug for

your protection against shock hazard. Be sure to plug directly into a properly grounded

four-prong receptacle. Do not cut or remove grounding prong from plug.

Note:

This appliance cannot be safely operated in the event of a power failure. No attempt

should be made to operate during a power failure. Disconnect power supply before servicing.

PRE-OPERATION CHECK

Be sure that all parts are installed in the proper location. Refer to OPERATION section for lighting proce-

dure. Start broiler and test for proper operation.

INSTALLING GAS APPLIANCE CONNECTORS

AND FLEXIBLE GAS LINES CORRECTLY

RESTRAINING DEVICE

INSTALLATION AND USE

This high strength restrainer is to be used with all moveable (castered) appliances. It fully complies with

American Gas Association requirements. References: Z21.69, Z83.11, and Z21.41 with current revisions.

Installation is quick and positive. In Canada, device is in accordance with CAN 1-6.9-M70 Quick

Disconnect Devices for use with gas fuel, and CAN 1-6.10-88 metal connectors for gas appliances.

Correct length for any appliance is simply a matter of loosening two adjuster clips (1) and re-tightening.

(3" to 6" shorter than appliance connector is desired length.)

Restrainer is made of heavy duty steel cable, with a strong scissor hood (2) at one end, and an equally

strong spring hook (3) at the other. Cotter pin (4) is supplied to secure the installation.

For safety in the kitchen area, and to insure maxi-

mum service life, it is vitally important to correctly

install connectors.

In order to avoid sharp kinks or excessive bends

that could have a damaging effect on the connec-

tor, it may be necessary to attach pipe elbows in

order to bring the connector into its proper plane.

For easy movement of the appliance, the connec-

tor should be installed with a "lazy" loop for mini-

mum tension.

Note: Gas appliances should be disconnected

prior to maximum movement. (Minimal move-

ment is possible to connect hose.)

WRONG

Avoid sharp bends and

kinks when pulling equip-

ment away from wall.

RIGHT

Minimum pull of equip-

ment is permissible for

accessibility to quick dis-

connect device.

GAS SYSTEM CONTROLS

1. Main Gas Pressure Regulator.

Controls the gas pressure when the

High Gas is off.

2. High Gas Pressure Regulator.

Controls the gas pressure in High Gas mode.

3. Main Gas Solenoid Valve.

4. High Gas Solenoid Valve.

5. Manual Gas Valve.

Valve is open when in line with pipe.

Gas Safety Valve

(red push button)

5 Amp Fuse

Pilot Ignitor

(red)

Bun Platen Thermostat

Gas Gauge

Recommended Settings:

Natural Gas - 3” Low, 5” High

Propane - 8” Low, 11” High

Motor Breaker Switch

(Model 1450 has two)

Motor Speed Control

(Model 1450 has two)

Main On/Off Switch

Power On Indicator Lamp

(red)

High Gas Indicator Lamp

(amber)

C. OPERATION

Controls and Indicators

WARNING: Use extreme caution when making adjustments to the gas pressure regulator. Only

authorized personnel should open the control box.

STEP-BY-STEP LIGHTING PROCEDURE

Before lighting, make sure that all parts are installed in the proper location, all controls are

turned off, and the ventilation hood fan is turned on.

1. Turn on Main Power Switch. 1 2

2. Turn on Motor Switch.

3. Set Motor Speed Control knob to 3 4

desired setting.

4. Set the Bun Platen Thermostat to

the desired setting. (Use a setting of

475° F to start.)

5. Open the Manual Gas Valve. The valve is 5 6

open when the handle is in-line with the pipe.

6. Push and hold the Red Push Button Valve.

This will start the flow of gas to the pilot lights.

While holding in the Red Button, push the Ignitor

button on the front of the control box. After the

pilot lights, hold the Red Valve in for 30 seconds

to allow the thermocouple to heat. When you

release the Red Push Button, the burners

should ignite.

If the ignitor is not working, use a long-stem

lighter to manually light the pilot.

7. After lighting the broiler, check the gas pressure

to be sure it is adjusted to the levels stated on the

machine rating plate. Allow the broiler at least

40 minutes to warm up.

SHUTDOWN PROCEDURE

For EMERGENCY shutdown, turn off the Main Power switch and shut off the manual gas valve.

For PLANNED shutdowns - Clear machine of all food products. Allow the machine to run empty for 15 minutes in order to

burn off the residue on the belt. Allow the machine to cool with the meat belt running, before you disassemble. Turn Main

Power and Motor switches off.

CAUTION: Turn all appliance switches off before disconnecting cord from power supply.

AUTOMATIC TEMPERATURE CONTROL (ATC)

The Nieco Automatic Temperature Control (ATC) is a system that operates the broiler at two different

energy input rates; a high energy input for initial warm-up and periods of high volume, and low energy for

regular operation. This dual input rate and the ATC allow the broiler to operate at a very consistent tem-

perature throughout the day and thus provide a very consistently broiled product. Since the broiler will

remain on the lower input rate (low gas) most of the day, a substantial energy savings is realized.

The ATC consists of two gas pressure regulators piped in parallel, a solenoid valve in series with the high

gas pressure regulator, a probe to sense the temperature at the loading end of the broiler, and a control

unit which is operated by the signals from the probe. The control unit causes the solenoid valve to open

and close. When the valve is open, the machine is in high gas mode, and the gas pressure is increased

to heat up the broiler.

Under heavy product loads, the temperature sensed by the ATC probe will drop low enough to cause the

ATC to open the solenoid valve. When the solenoid valve opens, the amber indicator light on the control

panel will light. The ATC will keep the broiler on high pressure until the temperature sensed by the probe

returns to the calibrated setting.

CALIBRATING THE ATC

1. Loosen the control knob lock screw and set the ATC control knob to 600° F.

2. Turn on the Main Power Switch.

3. Turn on the Motor Power Switch.

4. Light the broiler following the procedure in this manual.

5. The broiler should be in high gas mode at this time. (Amber light on.)

6. When the broiler reaches 600°, the high gas will shut off, and the broiler will be in low gas.

7. 40 minutes after lighting the broiler,

slowly turn the ATC control knob up (clockwise) until

the high gas clicks on. This is the idle temperature of the broiler.

8. As soon as the high gas turns on, slowly turn the ATC down (counter clockwise) 10° to 20°

below the point where the high gas turns on.

9. Tighten the control knob lock screw to prevent accidental movement.

10. The control knob setting may need a minor adjustment on the first day of use, in order to

maintain 10° to 20° below the normal idle temperature. Once the adjustment is correct, it

need not change from day to day unless the broiler operating conditions change.

WARNING

Never set the ATC control knob at a setting high enough to keep the broiler in high gas pressure. The

machine may be damaged, energy costs will be much higher, and some broiler parts may wear out pre-

maturely.

TYPICAL CARL’S JR. ATC TEMPERATURES

The following are the results of ATC Temperature Setting tests. Tests were performed on the 824B/1424

Carl’s Jr. broiler with 2” pressure difference between high and low. Note: These are as run at Nieco

Corporation and can be expected to vary according to individual store conditions. These temperatures

should be indicative of store temperatures, but not actual:

FOR NATURAL GAS:

1. #50 Orifices: Low Pressure High Pressure ATC Temperature

2” 4” 735°

2.5” 4.5” 745°

3” 5” 790°

3.2” 5.2” 820°

FOR L.P.G. (PROPANE):

2. #57 Orifices: Low Pressure High Pressure ATC Temperature

7” 10” 715°

7.5” 10.5” 725°

8” 11” 770°

8.2” 11.2” 800°

Note: ATC temperature is the dial temperature, not

the set point, which should be about 15° lower.

BUN GRILLING PLATEN

The 1424 is equipped with independently adjustable dual bun grilling platens. The clearance of each platen is adjusted by

turning the black handles located directly above the platens, at the feed end of the machine. Frequent adjustment should

not be necessary. The recommended initial setting for the bun platen is 475°.

CARL’S JR. PRODUCT TEMPERATURE STANDARDS

Meat patties: 160° MINIMUM

Chicken patties: 165° MINIMUM

Steak Sandwich 160° MINIMUM

Set the broil times so that all meat and chicken products are cooked above the minimum temperatures. Always be certain

to check the product temperature frequently. These are the current Carl’s Jr. product specifications as of 8/98. Always

check with management personnel to be certain that proper Carl’s standards are maintained.

CARL’S JR. BROILER SETUP CHART

Start at 2:30 and adjust as needed after product temperature checking and verification.

MODELS 1424/824 & 1124 BELT TIMES AND LINKS PER MINUTE

Time Model 1124 Models 824/1424

2:15 22.8 LPM 22.8 LPM

2:30 20.5 LPM 20.5 LPM

2:45 18.6 LPM 18.6 LPM

3:00 17.1 LPM 17.1 LPM

3:15 15.7 LPM 15.7 LPM

Gas Settings:

Low 4.25” W.C. 3” W.C.

High 4.25” W.C. 5” W.C.

Note: Gas settings are as set at the factory, subject to adjustment at time of start-up and broiling performance

verification.

Broil time is travel time of product from the center line of the feed end shaft to the center line of the discharge

end shaft.

FEED SHAFT

DISCHARGE SHAFT

32”

38.5”

MODEL 1124

MODEL 824/1424

BROIL TIME

D. ASSEMBLY/DISASSEMBLY AND CLEANING

If this appliance is connected to the gas supply by a flexible gas line and quick disconnect coupling, it must also be con-

nected to a restraining device (see installation instructions). If the appliance is moved and then returned to its original

position, it must be reconnected to the restraining device and the casters locked before resuming operation.

1. Clear machine of all food products. Allow the machine to run empty for 15 minutes in order to burn off the residue on

the belt. Allow the machine to cool with the meat belt running, before you disassemble. Turn Main Power and Motor

switches off.

2. Remove the Side Panels by 2 3

lifting up and off. Wipe clean

with a degreaser.

FROM THE FRONT OF THE BROILER

3. Remove the Patty Feeder by

lifting up and out. Clean daily

using soap and water.

4. Remove the Upper Disposable Burner 4 5

Front Reflector, and clean

with soap and water.

5. Remove the Grease Pan by sliding

it out the front. Clean daily using

soap and water.

6. Remove the Belt Scraper. Notice 6 7

the position it sits in before

removing, so that you can replace

it properly. Clean daily using soap

and water or degreaser.

7. Scrape the shafts (axles)with the special

tool provided, or with a flat head

screwdriver.

FROM THE LEFT SIDE OF THE BROILER

8. Remove the Grease Chute and 8

Grease Box, and clean using

soap and water.

9. Remove the Burner Access Cover. 9 10

10. Slide the Lower Disposable Burners out and

remove the Protective Shields.

Clean the shields by scraping off

any built up residue, then soak in

soap and water.

CLEAN THE SHIELDS DAILY.

This will help prolong the life of the

disposable burner and keep the

broiler cooking properly.

FROM THE BACK OF THE BROILER

11. Remove the awning by lifting up 11 12

and off. Clean using soap and

water.

12. Remove the Patty Discharge Pan and

Insert. Clean daily using hot soapy water,

and sanitize.

13. Remove the Stripper Blade (Doctor Blade). 13 14

Scrape any built up residue

from the blade. Clean by soaking

in soap and water. Sanitize.

14. Remove the Lower Burner

Reflector. Notice the position

of the piece before removing it,

so that you can re-install it

properly. Clean by soaking

in soap and water.

APPROVED CARL’S JR. CLEANING TOOLS

BURNER/MEAT BELT

BRUSH

CKE # 70351

SMALL ORIFICE BRUSH

CKE # 70357

MEAT BELT SHAFT

CLEANING TOOL

CKE # 70352

VENTURI BRUSH

CKE # 70358

WEEKLY CLEANING

15. Remove the Lower Disposable Burners 15

through the access hole in

the side of the broiler.

Clean the Distributor Screen

and Venturi in the same fashion

as the Upper Burners. Refer

to instruction 16 below.

16. Remove the Upper Disposable Burners 16

and clean as follows:

A. Remove Reverberator and clean

with a stiff bristle brush.

REPLACE REVERBERATOR AT

THE FIRST SIGN OF BREAKAGE.

DO NOT SOAK OR SUBMERGE THE DISPOSABLE BURNERS IN WATER. WATER CAN DAMAGE THE

DISPOSABLE BURNER, CAUSING IMPROPER BURNER PERFORMANCE.

17. Wipe off the frame and other internal parts of the broiler. Do not spray anything (i.e. clinging degreaser) inside the

broiler.

B. Clean Distributor Screen with a stiff

bristle brush.

HOLD DISPOSABLE BURNER WITH

THE SCREEN FACING DOWN

WHILE BRUSHING.

This prevents particles from dropping

down and lodging inside the burner.

C. Clean Disposable Burner Venturi

with a stiff bristle brush.

HOLD DISPOSABLE BURNERS

SO THAT PARTICLES WILL NOT

DROP INSIDE.

WEEKLY CLEANING

18. From the exterior of the manifold, wipe the

area around the orifices with a clean towel.

19. Using the Orifice Brush, carefully

clean ALL orifices.

CAUTION: NEVER CLEAN BURNER ORIFICES WITH ANYTHING OTHER THAN THE APPROVED BRUSH,

(ie. PAPER CLIP, TOOTHPICK etc...) AS THE ORIFICE WILL BE DAMAGED. THIS WILL CAUSE

IMPROPER BURNER OPERATION AND WILL AFFECT THE PERFORMANCE OF YOUR BROILER.

18.

19.

E. CONVEYOR BELT REMOVAL

Before beginning, notice the way the belt runs through the broiler. Also notice the direction the knuckles face. Be sure to

re-assemble in the same way.

1. Run belt until the Master Link is 1

near the front idler shaft.

2. Lift shaft and Teflon Blocks up, 2 3

and slide the blocks out.

3. Unhook the Master Link.

To reassemble, reverse the procedure. Be sure to reassemble the belt with the knuckle opening facing away from the

direction of travel.

F. CONVEYOR BELT TENSION

Maintain proper tension on the conveyor belts to prevent jamming. Bearing spacers (pictured below) are

supplied with the broiler to make minor tension adjustments. Major tension adjustments are made by

removing a link or links from the belt.

The diagram on the left shows the spacer in the stored position. The diagram on the right shows the

spacer behind the teflon bearing tightening the belts.

Belt tension should be checked monthly. To do this, allow the machine to cool, then grip the idler shaft at

each end and pull on it. If the shaft and bearings move 3/16” or more, the spacers should be placed

behind the bearings to tighten the belts. If the spacers are already behind the bearings, return them to

the stored position and remove a link from the conveyor belt.

BROIL BELT PROBLEMS

Interference with stripper blade:

The most common belt problem to be expected is the physical interference of the belt with the stripper

blade. This is caused by bent or warped rods on the meat belt, and can be fixed by replacing the rods

that are causing the problem. Other causes are bent stripper blades, or utensils jammed in the belt.

Blocked belts:

When trouble shooting drive problems, it is important to ensure that the belt is not being blocked. To do

this, detach the drive chain and turn the meat belt by hand. The belt, with the motor detached, should

turn freely and easily. If the blockage has occurred which is preventing the belt from turning, the block-

age should be removed before the drive chain is re-attached. The drive chain can be easily removed

from the drive sprocket (on the motor shaft) by loosening the mounting bolts and raising the motor.

NOTE: Restaurant employees are NOT to remove the meat belt. Only Facilities Maintenance Personnel

are authorized to remove this belt.

Page is loading ...

Nieco Corporation 1424 Operating instructions

Brand: Nieco Corporation

Model: 1424

Category: Cookers

Type: Operating instructions

This manual is also suitable for

1124
824

Download PDF

report

Nieco Corporation 1424 Operating instructions

This manual is also suitable for

Nieco Corporation 1424 Operating instructions

Related papers

Other documents