Robe City Source 96 RGBW RGBW WDMX User manual

Version 1.

6

CitySource 96 (RGBW)

2

Table of contents

1. Safety instructions ...................................................................................................................................................... 3

2. Fixture exterior view ................................................................................................................................................... 5

3. Installation .................................................................................................................................................................. 5

3.1 Rigging the fixture ................................................................................................................................................. 5

3.2 Connection to the mains ...................................................................................................................................... 6

3.3 Changing the lens array ........................................................................................................................................ 6

3.4 Installation of the barn-doors and top hat/half top hat ....................................................................................... 8

3.5 DMX 512 connection ............................................................................................................................................ 8

3.6 Master/slave connection ...................................................................................................................................... 9

3.7 Stand-alone operation ........................................................................................................................................ 10

4. CitySource 96 (RGBCW) - DMX protocol ................................................................................................................... 11

5. Control menu map .................................................................................................................................................... 13

6. Fixture menu ............................................................................................................................................................. 15

6.1 Fixture Address ................................................................................................................................................... 16

6.2 Fixture information ............................................................................................................................................. 16

6.3 Personality .......................................................................................................................................................... 17

6.4 Manual mode ...................................................................................................................................................... 18

6. 5 Test sequences................................................................................................................................................... 18

6.6 Stand-alone setting ............................................................................................................................................. 18

6.7 Special functions ................................................................................................................................................. 20

7. RDM .......................................................................................................................................................................... 21

8. Error and information messages .............................................................................................................................. 22

9. Wireless DMX operation ........................................................................................................................................... 22

10. Technical specifications .......................................................................................................................................... 23

11. Cleaning and maintenance ..................................................................................................................................... 26

CitySource 96 (RGBW)

3

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE POWERING OR INSTALLING YOUR CitySource 96 !

Save it for future reference.

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a

safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in

this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual

or any unauthorized modification to the device.

Please consider that damages caused by manual modifications to the device are not subject to warranty.

1. Safety instructions

DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!

Make sure that the available voltage is not higher than stated on the rear panel of the fixture.

This fixture should be operated only from the type of power source indicated on the marking label. If you are not

sure of the type of power supplied, consult your authorized distributor or local power company.

Always disconnect the fixture from AC power before cleaning, removing or installing the fuses, or any part.

Do not overload wall outlets and extension cords as this can result in fire or electric shock.

Make sure that the power cord is never crimped or damaged by sharp edges. Check the fixture and the power cord

from time to time.

Do not install the unit near naked flames.

During the operation the housing becomes hot (up to 80°C)

Refer servicing to qualified service personnel.

This fixture falls under protection class I. Therefore this fixture has to be connected to a mains socket outlet with

a protective earthing connection.

Do not connect this fixture to a dimmer pack.

LED light emission. Risk of eye injury.

Do not look straight at the fixture´s LEDs during operation. The intense light beam may damage your eyes.

Keep compustible materials at least 30 cm away from the fixture.

If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation water might damage your device. Leave the device switched off until it has

reached room temperature.

Do not shake the fixture. Avoid brute force when installing or operating the fixture.

CitySource 96 (RGBW)

4

This fixture was designed for indoor and outdoor use.

When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.

Avoid using the unit in locations subject to possible impacts.

The fixture body never must be covered with cloth or other materials.

Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.

Do not block the front objective LEDs with any object when the fixture is under operation.

The fixture becomes very hot during operation. Allow the fixture to cool approximately 30 minutes prior to

manipulate with it.

Operate the fixture only after having familiarized with its functions. Do not permit operation by persons not

qualified for operating the fixture. Most damages are the result of unprofessional operation!

Do not attempt to dismantle or modify the unit.

Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!

Please use the original packaging if the fixture is to be transported.

If this device will be operated in any way different to the one described in this manual, the product may suffer

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-

circuit, burns, electric shock etc.

CitySource 96 (RGBW)

5

2. Fixture exterior view

Standard version Wireles DMX version

3. Installation

3.1 Rigging the fixture

Ensure that the structure (truss) to which you are attaching

the fixture is secure

The fixture can be rigged in any orientation on a truss via the omega holder without altering its operation

characteristics. The mounting bracket allows to adjust desired fixture position (0°-360°). The mounting hole in the

mounting bracket has a diameter of 13 mm.

1. Lens array

2. Radiator

3. Mounting bracket

4. Tilt

-

lock screw

5. Power cable

6. Data cable (DMX in/out)

7. Control buttons

8. LED display

9. Antenna

CitySource 96 (RGBW)

6

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working load limits,

installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack

these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger.

Improper installation can result in bodily injury or damage to property.

For overhead use, always install a safety rope that can hold at least 10 times the weight of the fixture. You must

only use safety ropes with screw-on carbines. Pull the safety-rope through the mounting bracket and over the

trussing system etc. Insert the end in the carbine and tighten the fixation screw.

Caution: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety of a

possible installation, do not install the device.

The fixture can also stand directly on the flat surface (e.g. stage) by means of the removable stand:

3.2 Connection to the mains

Fixtures must be installed by a qualified electrician in accordance with all national

and local electrical and construction codes and regulation.

Install a suitable plug on the power cord, note that the cores in the power cord are colored according to the

following table.

Core (Eu)

Core (US)

Connection

Plug Terminal Marking

Brown

Black

Live

L

Light blue

White

Neutral

N

Yellow/Green Green Earth

This device falls under class one and must be grounded!

3.3 Changing the lens array

The standard beam angle of the fixture without lens-array is 12°.

If you need a wider beam angle than 12° , you have to install the eggcrate lens module 25° or the optional

eggcrate lens modules: 45°, 45°x15° or eggcrate top hat (for placing plastic foil under it).

How to install eggcrate lens module:

1. Disconnect the fixture from the mains.

2. Place the new eggcrate lens module (2) on the front side of the fixture and screw it to the housing by

means of the four M5x14 screws (1) with washers (3).

CitySource 96 (RGBW)

7

You can install a frost foil under the eggcrate top hat to get frost light output.

1. Disconnect the fixture from the mains.

2. Uninstall the eggcrate lens module 25° (2) as described above.

3. Place the frost foil (6) under the the eggcrate top hat (7) and secure it by means of the four screws (1) and

washers (3) on the fixture.

The dimension of the frost foil is 154mm x 103mm, max. thickness= 0.5mm.

The frost foil has to stand temperature of 85°C.

CitySource 96 (RGBW)

8

3.4 Installation of the barn-doors and top hat/half top hat

You can install the barn-doors or top hat/half top hat to better define illuminated surface.

1. Disconnect the fixture from the mains.

2. Remove the eggcrate lens module 25°(2) by unscrewing the four M5x14 screws (1) including washers (3).

3. Place the barn-doors module (4) or top hat/half top hat on the eggcrate lens module 25° (2) and screw

them on the fixture using four M5x14 screws (1) and washers (3) as shown on the picture below.

Never close the barn-doors during fixture operation

3.5 DMX 512 connection

The fixture is equipped with two 5-pin XLR connectors for DMX input/output.

Only use a shielded twisted-pair

cable designed for RS-485 and 5-pin XLR- connectors in order to connect the controller with the fixture or one

fixture with another.

Wiring of the XLR connectors:

DMX output DMX input

XLR socket (rear view): XLR plug (rear view):

1

– Shield

2

- Signal (-)

3

- Signal (+)

4

– Not connected

5

– Not connected

CitySource 96 (RGBW)

9

To build a DMX chain

1. Connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain.

2. Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture.

3. Always connect the DMX output with the input of the next fixture until all fixtures are connected.

Do not overload the link. Max. 32 fixtures may be connected on a DMX link.

Caution: Terminate the link by installing a termination plug in the output of the last fixture. The termination plug is

a male 5-pin XLR plug with a 120 Ohm resistor soldered between Signal (–) and Signal (+).

3.6 Master/slave connection

To build a master/slave-chain:

Connect the DMX output of the master fixture in the data chain with the DMX input of the first slave. Always

connect output with the input of the next slave until all slaves are connected (up to 32 fixtures).

Caution: It is necessary to terminate the input of the master fixture and the output of the last slave with a 120 Ohm

resistor in order to ensure the proper transmission on the data link.

CitySource 96 (RGBW)

10

3.7 Stand-alone operation

The fixtures on a data link are not connected to the controller but can execute pre-set programs which can be

different for every fixture. To set the program to be played, see the "Stand-alone setting" (menu "St.AL.").

"Stand-alone operation" can be applied to the single fixture or to multiple fixtures operating synchronously.

Synchronous operation of multiple fixtures requires that they must be connected on a data link and one of them is

set as a master (master mode) and the rest as the slaves (slave mode).

To set the fixture as the master or slave, see the " Fixture Address " (menu "A001").

Only one fixture can be set as the master.

The master fixture starts simultaneous program start in the other slave fixtures. All fixtures have a definite,

synchronized starting point when playing back their programs. The number of running program is the same in all

slaves and depends on the master's choice (menu "St.AL.“). Every fixture runs its program repeatedly, starting the

program step No.1 when requested by the master.

Example:

If the slave fixture has a shorter program length, it will continuously repeat its program until the master fixture

finishes its own program and restarts its program running (slave 1- prog.step 3 will not be finished).

If the slave fixture has a longer program length, it will restart at prog. step 1 before it completes all its prog.steps

(slave 2 - prog.step 5 will not be played)- see the picture bellow.

Note: Disconnect the fixtures from the DMX controller before master/slave operating, otherwise data collisions

can occur and the fixtures will not work properly!

CitySource 96 (RGBW)

11

4. CitySource 96 (RGBCW) - DMX protocol

Version 1.1

Mode/Channel

Value Function Type of control

1

2

*

3

4

5

6

-

1

-

0 - 255

Red LEDs

-

both

LED arrays

Red LEDs saturation control (0-100%)

proportional

-

2

-

0 - 255

Green LEDs

-

both

LED arrays

Green LEDs saturation control (0-100%)

proportional

-

3

-

0 - 255

Blue LEDs

-

both

LED arrays

Blue LEDs saturation control (0-100%)

proportional

-

4

-

0 - 255

White LE

Ds

-

both

LED arrays

White LEDs saturation control (0-100%)

proportional

-

1

0 - 255

Red LEDs

–

LED array

1

Red LEDs saturation control (0-100%)

proportional

-

2

0 - 255

Green LEDs

-

LED array

1

Green LEDs saturation control (0-100%)

proportional

-

3

0 - 255

Blue LEDs

-

LED array

1

Blue LEDs saturation control (0-100%)

proportional

-

4

0 - 255

White LEDs

-

LED array

1

White LEDs saturation control (0-100%)

proportional

-

5

0 - 255

Red LEDs

-

LED array

2

Red LEDs saturation control (0-100%)

proportional

-

6

0 - 255

Green LEDs

-

LED array

2

Green LEDs saturation control (0-100%)

proportional

-

7

0 - 255

Blue LEDs

-

LED array

2

Blue LEDs saturation control (0-100%)

proportional

-

8

0 - 255

White LEDs

-

LED array

2

White LEDs saturation control (0-100%)

proportional

1

-

5

-

9

0

1-15

16

17-55

56

57 - 95

96

97 – 134

135

136 - 174

175

176 -214

215

Colour macros

(255 values)

–

both

LE

D arrays

No function (for DMX mode 4 and 6)

White (for DMX mode 1)

White tones (cool warm)

Blue (Blue=full, Red+Green+White=0)

Red=0, Greenup,Blue =full, White=0

Light Blue (Red=0, Green=full, Blue =full, White=0)

Red=0, Green=full, Bluedown, White=0

Green (Red=0, Green=full, Blue =0, White=0)

Redup, Green=full, Blue=0, White=0

Yellow-green (Red=full, Green=full, Blue=0, White=0)

Red=full, Greendown, Blue=0, White=0

Red(Red=full, Green=0, Blue=0, White=0)

Red=full, Green=0, Blueup, White=0

Magenta (Red=full, Green=0, Blue=full, White=0)

step

proportional

step

proportional

step

proportional

step

proportional

step

proportional

step

proportional

step

CitySource 96 (RGBW)

12

Mode/Channel

Value

Function

Type of control

1

2

*

3

4

5

6

1

-

5

-

9

216 - 254

255

Colour ma

cros

–

both

LED arrays

Reddown, Green=0, Blue=full, White=0

Blue (Red=0, Green=0, Blue=full, White=0)

proportional

step

-

6

-

10

0-31

32-63

64-95

96-127

128-143

144-159

160-191

192-223

224-255

Shutter/ Strobe

–

both

LED arrays

Shutter closed

Shutter open

Strobe-effect from slow to fast

Shutter open

Opening pulses in sequences slow--> fast

Closing pulses in sequences fast --> slow

Shutter open

Random strobe-effects from slow to fast

Shutter open

step

proportional

step

proportional

step

proportional

step

2

-

7

-

11

0 - 255

Dimmer

–

both

LED arrays

Dimmer intensity from 0% to 100%

proportional

-

8

-

12

0 - 255

Dimmer fine

–

both

LED arrays

Fine dimmer intensity from low to high

proportional

*White LEDs lit proportionally when Red+Green+Blue LEDs are saturated together.

CitySource 96 (RGBW)

13

5. Control menu map

Default settings=Bold print

Menu Level 1

Menu Level 2

Menu Level 3

Menu Level 4

Menu Level 5

Menu Level 6

A001

dM.Ad.

001

-

512

MA.SL.

d.A

bL

MASt.

SLA

InFo

Poti.

FuLL

totL

rSEt

EcO

totL

rSEt

DM.In.

rEd1

0

-

255

:

F.dim

0

-

255

tEMP.

Cur.t.

boAr.

LEdS

Hi.tE.

boAr.

LEdS

rSEt

boAr.

LEdS

VErS.

IC1

P

ErS

dM.Pr.

Mod.1

Mod.2

Mod.3

:

Mod.

6

dISP.

d.On

On

, Off

d.Int.

20...

100

turn

CitySource 96 (RGBW)

14

Menu Level 1

Menu Level 2

Menu Level 3

Menu Level 4

Menu Level 5

Menu Level 6

tEM.U.

°

C

,

°

F

bALA

On,

Off

C.bAL.

rEd

0..

200

..255

GrE

n

0..........

255

bLu

E

0..

237

..255

Stor

LOAd

FuLL

EcO

In.Po.

rEd1

0

-

255

:

F.dim

0

-

255

Stor.

dFSE

MAn.M.

PrE.C.

rEd1

rE

.01

..rE

.03

:

dimr

di

.

0

1

...di.

06

Man.C.

rEd1

0

-

255

:

F.

dim

0

-

255

t

ESt

St.AL.

Auto

Off

tESt

PrG.1

:

PrG.3

PLAY

tESt

PrG.1

:

CitySource 96 (RGBW)

15

Menu Level 1

Menu Level 2

Menu Level 3

Menu Level 4

Menu Level 5

Menu Level 6

PrG.3

Edit

PrG.1

St

.01

P.End

1

-

68

:

rEd1

0

-

255

PrG.3

St.

68

:

S.tim.

0

-

25.5

sec

CoPY

SPEC.

rdML

rdMH

Adj.

DMH

rEd1

:

F.dimr

CaL.U.

rEd1

:

W

h

2

Stor.

vAdI*

v.InF.

No.LI (0

-

100)

r.UnL.

No.LI

u

Pd.

* Only for WDMX version

6. Fixture menu

The control panel menu allows to set the fixture according to your needs, obtain information on its operation, test

its various parts and lastly program it, if it has to be used in a Stand-alone mode.

The four control buttons on the front have the following functions:

- ESCAPE button-leaves menu without saving changes.

- ENTER button- enters menu, confirms adjusted values and leaves menu.

- UP and - DOWN buttons - move between menu items on the same level, sets values.

After switching the fixture on, the fixture display shows the current DMX address:

Use the UP/DOWN buttons to scroll through the various menu items. To select desired item, press the ENTER.

CitySource 96 (RGBW)

16

6.1 Fixture Address

Use this menu to set the DMX address of the fixture or set the fixture as a Master (Slave).

dM.Ad. --- DMX addressing. Select this submenu to set a DMX start address.

To set a DMX address.

1. Use the UP/DOWN buttons to find “ A001“ menu.

2. Press the ENTER button.

3. Use the UP/DOWN buttons to select desired start address.

4. Press the ENTER button to confirm the choice.

MA.SL. --- Master/slave addressing. Select this submenu to set the fixture as a master or slave. Option "d.AbL"

deactivates master/slave setting.

To set a fixture as a master or slave.

1. Use the UP/DOWN buttons to find “A001“ menu.

2. Press the ENTER button.

3. Use the UP/DOWN buttons to select “ MA.SL.“ item.

4. Press the ENTER button.

5. Use the UP/DOWN buttons to select either master (MASt) or slave (SLA)

6. Press the ENTER button to confirm the choice.

Note: After switching on, the CitySource 96will automatically detect whether DMX 512 data is received or not.

If there is no data received at the DMX input, the display will start to flash with actually set address.

6.2 Fixture information

Use this menu to read useful information about the fixture status.

To display desired information.

1. Use the UP/DOWN buttons to find the “ InFo“ menu.

2. Press the ENTER button.

3. Use the UP/DOWN buttons to select the required menu item.

4. Press the ENTER button to confirm the choice.

Po.ti. --- Power On Time. Use the menu item to read the number of operation hours for each LEDs operating

mode.

FuLL---Max light output from the fixture.

totL - the function shows the total number of the operation hours in the “FuLL” mode since the

CitySource 96 has been fabricated.

rESEt - the function shows the number of the operation hours that the CitySource 96

has been powered on in the “FuLL” mode since the counter was last reset. In order to reset this

counter to 0 you have to press and hold the UP and DOWN buttons and at the same time press

the ENTER button.

EcO---Economical mode.

totL - the function shows the total number of the operation hours in the “EcO” mode since the

CitySource 96 has been fabricated.

rESEt - the function shows the number of the operation hours that the CitySource 96

has been powered on in the “EcO” mode since the counter was last reset. In order to reset this

counter to 0 you have to press and hold the UP and DOWN buttons and at the same time press

the ENTER button.

CitySource 96 (RGBW)

17

DM.In.---DMX values. Select this function to read DMX values of each channel received by the fixture.

tEMP --- Fixture Temperatures. Select this menu to read the temperatures of the fixture:

Cur.t. --- the current temperature of the fixture inside.

Hi.tE. - the menu item shows the max. temperatures of the fixture inside since

the CitySource 96has been fabricated.

rSEt --- the menu item shows the maximum temperatures of the fixture inside since the counter

was last reset. In order to reset this counter to 0 you have to press and hold the UP and DOWN

buttons and at the same time press the ENTER button.

Note: The ambient temperature should not exceed 40°C.

Measuring points:

LEdS.--- the temperature of the LEDs module.

boAr. --- the temperature on the PCB in the fixture base.

The temperatures can be displayed in either °C or °F units - see option “tEM.U“ in the menu “Pers“.

VErS. ---Software Versions. Select this function to read the software version of the fixture processor.

6.3 Personality

Use this menu to modify the CitySource 96operating behaviour.

DM.Pr. --- DMX preset. Select this menu item to set a desired DMX mode. Please refer to the chapter "DMX

protocol" for detail description of each DMX mode.

DiSP. --- Display adjusting. This function allows you to change the display settings.

d.On --- this function allows you to keep the display on or to turn off automatically 2 minutes

after last pressing any button on the control panel.

d.Int. --- select this function to adjust the display intensity (20-min.,100-max.).

turn --- select this function to turn the display by 180°.

tEM.U. --- Temperature Unit. Use this menu in order to display the fixture temperatures in desired units: °C or °F.

bALA --- Balance Use this menu item to enable (On) or disable (Off) the white balance which is set in the “White

colour balance“ menu below. I f this function is set off, the CitySource 96will use maximum values (255) of

saturation for red, green and blue colour. This function has to be set on before adjusting a white balance.

C.bAL. --- White Colour Balance. The menu gives access to the setting of the white balance.

To set white colour balance.

1. Use a DMX controller or the “ Man.C.“ menu to set all LEDs on max. saturation.

2. Use the UP/DOWN buttons to find the “ Pers.“ menu.

3. Press the ENTER button.

4. Use the UP/DOWN buttons to select the “C.bAL“menu.

5. Press the ENTER button and the “rEd“ item will appear on the display.

6. Press the ENTER button and use the UP/DOWN buttons to set new max. value for the red LEDs.

7. Press the ENTER button to confirm the choice.

8. Use the UP/DOWN buttons to select next colour, the “GrEn“.

9. Repeat steps 6-7 for this channel.

10. Use the UP/DOWN buttons to select the last colour, the „bLuE“ and repeat steps 6-7 for this colour.

LoAd

--- Load of LEDs. The menu allows to choose 2 different operating modes for fixture´s LEDs.

CitySource 96 (RGBW)

18

FuLL --- Maximum light output.

EcO. --- The light output is decreased by 25%.

In.Po. --- Init effect positions. Use this function to set all effects to the desired positions to which they will move

after switching the fixture on (if DMX is not being received).

Note. If DMX mode 1 is selected, only values set at items “MACr” (macro) and dinr (dimmer) will be accepted.

dF.SE. --- Default Settings .The menu item sets all fixture parameters to the default (factory) values.

6.4 Manual mode

Use this menu for control the fixture without connected DMX console.

PrE.C. --- Preset effects control. Select this menu to call up preset positions of the channel effects.

Man.C. --- Manual effect control. Select this menu to control all channels via buttons of the control board.

To control fixture channels.

1. Use the UP/DOWN buttons to find “ Man.C“ menu.

2. Press the ENTER button.

3. Use the UP/DOWN buttons to select desired effect (channel).

List of control channels:

“rEd1” - red LEDs saturations-array1

“GrE1“ - green LEDs saturations-array1

“bLu1“ - blue LEDs saturations-array1

“Whi1“ - white LEDs saturations-array1

“rEd2” - red LEDs saturations-array2

“GrE2“ - green LEDs saturations-array2

“bLu2“ - blue LEDs saturations -array2

“Whi2“ - white LEDs saturations-array2

“MACr“ - colour macros

“Stro.“ - a strobe, shutter

“dimr“ - a dimmer

“F.dim” – a fine dimmer

4. Press the ENTER button and use the UP/DOWN buttons to set value , press the ENTER button to confirm it.

6. 5 Test sequences

Use this menu to run demo-test sequences without an external controller, which will show you some possibilities

of using the CitySource 96.

6.6 Stand-alone setting

The fixtures on a data link are not connected to the controller but can execute pre-set programs which can be

different for every fixture. “Stand-alone operation” can be applied to the single fixture or to multiple fixtures

operating synchronously.

CitySource 96 (RGBW)

19

Synchronous operation of multiple fixtures requires that they must be connected on a data link and one of them is

set as a master (“MASt“) and the rest as the slaves (“SLA“). Up to 32 fixtures can be connected in a master/slave

chain. Only one fixture can be set as the master.

Note: Disconnect the fixtures from the DMX controller before master/slave operating, otherwise data collisions can

occur and the fixtures will not work properly. See the chapters “Stand-alone operation“ and “ Master/slave

connection“.

Auto. --- Automatic playback. This function allows you to select the program which will be played after switching

the fixture on. Selected program will be played continuously in a loop.

1. Use the UP/DOWN buttons to find “ St.AL.“ menu.

2. Press the ENTER button.

3. Use the UP/DOWN buttons to select “ Auto“ item.

4. Press the ENTER button.

5. Use the UP/DOWN buttons to select desired program.

6. Press the ENTER button to confirm the choice.

PLAY --- Playing program. By enter to this menu a complete overview of all programs is offered, from which the

program to be run can be selected.

1. Use the UP/DOWN buttons to find “ St.AL.“ menu.

2. Press the ENTER button.

3. Use the UP/DOWN buttons to select desired program.

4. Press the ENTER button. The selected program runs in a loop.

Edit --- Editing a program. The fixture offers 3 freely editable programs (EPG.1-EPG.3) each up to 68 steps. Every

program step includes a fade time-the time taken by the step´s channel status to reach the desired level and a

step time-the total time occupied by the step in the program.

E.g. If “F.tim.“=5 second and “S.tim.“=20 second, effects will go to the desired position during 5 seconds and after

that they will stay in this position for 15 seconds before going to the next prog. step

1. 1. Use the UP/DOWN buttons to find “ St.AL.“ menu and press the ENTER button.

2. Use the UP/DOWN buttons to select “Edit“ menu and press the ENTER button.

3. Use the UP/DOWN buttons to select a program you want to edit (PrG.1-PrG.3 and press ENTER button.

4. Use the UP/DOWN buttons to select a desired program step ("St.01" - "St.68") and press ENTER button.

5. Use the UP/DOWN buttons to select a channel you want to edit and press the ENTER button.

List of editable items:

“P.End” - a total number of the program steps (value 1-68). This value should be set before start

Programming (e.g. if you want to create program with 10 steps, set P.End=10).

“rEd1”- “rEd2”- a red LEDs saturation array1/array2 (0-255)

“GrE1“-“GrE2“ - a green LEDs saturation array1/array2 (0-255)

“bLu1“-“bLu2“ -a blue LEDs saturation array1/array2 (0-255)

“Whi1“ - “Whi2“ – a white LEDs saturation array1/array2 (0-255)

“MACr“ - colour macros (0-255)

“Stro.“ - a strobe, shutter (0-255)

“dimr“ - a dimmer (0-255)

“F.dim”- a fine dimmer (0-255)

“F.tim.“ - a fade time, (0-25.5) seconds

“S.tim.“ - step time, value (0-25.5) seconds

“COPY“. – this item duplicates the current prog. step to the next prog. step. The item “P.End” is increased

automatically.

6. Use the UP/DOWN buttons to set a DMX value of the channel and then press the ENTER button.

7. Use the UP/DOWN buttons to select next channel and press the ENTER button.

8. After having set all channels in the current program step, press the MODE button to go by one menu level

back and select another program step.

CitySource 96 (RGBW)

20

6.7 Special functions

rdML --- Code.This menu item shows the first part of the RDM identification code.

rdMH --- Code. This menu item shows the second part of the RDM identification code.

AdJ --- Effect Adjustment. The menu allows calibration of each LEDs array.

dMH --- DMX Values. The menu item enables to control all LEDs before calibrating each LEDs array.

CAL.U --- Calibrating unit. The menu serves for fine current calibration of LEDs during fixture burn-in at

a factory. Each LED array can be calibrated separately. Users should not change the setting.

vAdI --- Wireless DMX. The menu serves for reading of the wireless operation status (only for WDMX version).

v.InF. --- Wireless DMX information. The menu item shows level of received signal in %. If the fixture is not

linked to the transmitter, “no.LI” is displayed.

v.UnL. --- Wireless DMX unlink. The item serves for unlinking the fixture from transmitter

uPd.M. --- Updating mode. The menu item allows you to update software in the fixture via either serial or USB port

of PC.

The following are required in order to update software:

- PC running Windows 95/98/2000/XP or Linux

- DMX Software Uploader

- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)

- Robe Universal Interface (if you want to use an USB port of PC)

Note1: Software update should execute a qualified person. If you lack qualification, do not attempt the update

yourself and ask for help your ROBE distributor.

Note 2: DMX address, programs 1-3 and all items in the menu "PErS" will be set to their default values.

To update software in the fixture:

I. Installation of the DMX Software Uploader.

1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.

2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.

3. Unpack the program from the archive.

.

II.Fixture software updating.

1. Determine which of your port is available on your PC and connect it:

- with the DMX input of the fixture if you using the flash cable RS232/DMX

- with the DMX input of the Robe Universal Interface if you using the USB cable.

Disconnect the fixture from the other fixtures in a DMX chain. Turn both the computer and the fixture on.

Make sure the lamp is switched off (only if the fixture involves a lamp).

2. Switch the fixture to the updating mode:

1 Use the UP/DOWN buttons to find “SPEC.“ menu.

2 Press the ENTER button.

3 Use the UP/DOWN buttons to select “ uPd.“ item.

4 Press the ENTER button

5 Use the UP/DOWN buttons to select “ yES“ option

6 Press the ENTER button

Note: If you do not want to continue in software update, you have to switch off and on the fixture

to escape from this menu.

3. We recommend to cancel all running programs before start of the Software Uploader.

4. Run the Software Uploader program. Select desired COM and then click on the Connect button.

Page is loading ...

Robe City Source 96 RGBW RGBW WDMX User manual

Robe City Source 96 RGBW RGBW WDMX User manual

Related papers

Other documents