Tektronix Z780N - Phaser 780 Color Laser Printer Installation guide

P H A S E R S H A R E

®

N E T W O R K I N G

Manual

®

www.tek.com/Color_Printers/

PhaserShare

®

Networking Manual

V2 January 1999

071-0180-01

Copyright

©

Tektronix, Inc.

Unpublished rights reserved under the copyright laws of the United States. Contents of this publication may not be reproduced in

any form without permission of Tektronix, Inc.

Tektronix

®

, Phaser

®

, PhaserShare

®

, the TekColor logo, ColorStix

®

, ColorCoat

®

, and Made For Each Other

®

are registered

trademarks of Tektronix, Inc. Finepoint™, PhaserLink™, PhaserPrint™, the TekColor name, and PhaserSym™ are trademarks of

Tektronix, Inc.

Adobe

®

and PostScript

®

are trademarks of Adobe Systems Incorporated which may be registered in certain jurisdictions.

Apple

®

, AppleTalk

®

, LocalTalk

®

, EtherTalk

®

, TokenTalk

®

, and Macintosh

®

are registered trademarks of Apple Computer, Inc.

SGI™ is a trademark of Silicon Graphics, Inc.

SPARC

®

is a registered trademark of SPARC International, Incorporated. SPARCstation™ is a trademark of SPARC International,

Inc., licensed exclusively to Sun Microsystems, Inc.

Tektronix Phaser 840, Phaser 740, Phaser 780, and Phaser 360 printers are certiﬁed as NetWare print server

devices, on both 3.12 and 4.1

x

NetWare systems. Bindery mode is also certiﬁed to comply on both 3.12 and 4.1

x

NetWare systems. NetWare NDS is certiﬁed on 4.1

x

NetWare systems.

Novell® and NetWare® are registered trademarks of Novell, Inc.

UNIX

®

is a registered trademark in the United States and other countries, licensed exclusively through X/Open

Company, Ltd.

Times™, Helvetica™ and Palatino™ are trademarks of Linotype-Hell AG and/or its subsidiaries.

Other marks are trademarks or registered trademarks of the companies with which they are associated.

PANTONE

®

*

Colors generated by Phaser Color Printers are four- and/or three-color process simulations and

may not match PANTONE-identiﬁed solid color standards. Use current PANTONE Color Reference Manuals

for accurate colors.

PANTONE Color simulations are only obtainable on these products when driven by qualiﬁed Pantone-licensed software

packages. Contact Pantone, Inc. for a current list of qualiﬁed licensees.

*

Pantone, Inc.’s check-standard trademark for color reproduction and color reproduction materials.

PhaserShare Networking Manual

iii

1 Network Printing with Tektronix Color Printers

Key components for networking Tektronix color printers 1

Network installation overview 6

The printer’s Configuration Page 6

How to tell which protocols are enabled 8

The printer’s networking software 8

Support for DOS systems 10

Tektronix PhaserPrint for UNIX software 10

2 PhaserShare Series B Network Interfaces

PhaserShare Series B Ethernet interface 11

PhaserShare Series B Token Ring card 14

PhaserShare Series B LocalTalk card 22

3 EtherTalk, LocalTalk, and TokenTalk Configuration

Before you begin 25

Configuration overview 25

Finding the printer’s name in the Chooser 26

Changing the printer’s name (optional) 27

Changing the printer’s EtherTalk/TokenTalk zone (optional) 29

Troubleshooting 30

4 Novell NetWare Configuration

The printer’s NetWare interface 31

Before beginning the configuration procedure 32

Configuration software for NetWare 33

NetWare configuration for Windows environments 33

Troubleshooting Windows configurations 36

Setting IPX frame types from the front panel 40

5 PhaserShare Administrator Software for NetWare Networks

Introduction to the PhaserShare Administrator 43

NetWare configuration with the PhaserShare Administrator 44

Installation 44

Using the PhaserShare Administrator 46

PhaserShare Administrator on-line help 50

6 TCP/IP Configuration Overview

Before you begin 52

Extracting files from unix.tar 52

Printing the Configuration Page 52

TCP/IP configuration overview 53

Contents

iv

PhaserShare Networking Manual

7 TCP/IP Printer Configuration (All Platforms)

Setting the printer’s IP addressing parameters 55

General information on setting IP parameters (front panel) 57

Setting IP parameters: Phaser 840 printer front panel 57

Setting IP parameters: Phaser 740 printer front panel 58

Setting IP parameters: Phaser 780 printer front panel 60

Setting IP parameters: Phaser 360 printer front panel 63

Setting IP parameters: RARP or BOOTP 65

Setting IP parameters: DHCP 66

Supported BOOTP/DHCP fields 68

Enabling and disabling RARP and BOOTP/DHCP (front panel) 69

Setting IP parameters: PhaserLink Printer Management Software 73

Controlling host access 76

Receiving printer status 79

8 TCP/IP Host Configuration (UNIX)

Configuring a host 83

Troubleshooting 94

9 TCP/IP Configuration (OS/2 Warp/LAN Server)

Setting the printer’s IP addressing parameters 95

Creating an LPR queue in OS/2 Warp Connect (direct LPR connection to the printer) 96

OS/2 client-to-server setup 97

Warp Server 4.0/Warp Connect 98

10 Windows NT

Setting the printer’s IP address 99

Adding the Windows NT 4.0 driver on a Windows NT 4.0 server or workstation 99

Adding the Windows NT 4.0 driver on a Windows NT 3.51 server 104

Adding a Windows NT 3.x driver 109

Windows NT network communication 112

Windows NT network troubleshooting 113

11 Windows 95 and Windows 98: PhaserPort Software

TCP/IP configuration for the PC 117

Setting the printer’s IP address 117

PhaserPort software installation 118

Adding a port for a new printer 120

Adding a port to an existing printer 120

Changing a port’s IP address 121

PhaserShare Networking Manual

v

12 PhaserLink Printer Management Software

System requirements 123

Multiple language support 123

Accessing printer information from a browser 124

Printer information pages 124

Printer status display 126

PhaserLink Printer Management Software help files 127

Setting printer parameters: PhaserLink Printer Management Software pages 128

Information Forwarding 128

13 Printer Management

Job accounting 129

PhaserLink PDF Direct Printing 130

Phaser 840 Intelligent Ready 131

PhaserLink Status Notification (Email Notification) 132

Usage Profile reports (Phaser 840, 740 and 780 printers only) 133

Printing Usage Profile reports from the front panel 134

Printing verbose Usage Profile reports from the front panel 135

Printing Usage Profile reports from PhaserLink Printer Management Software 136

Sending Usage Profile reports via email from the front panel 136

Sending Usage Profile reports via email: PhaserLink Printer Management Software 138

Controlling Usage Profile email reporting 139

Email to Tektronix 140

Reading Usage Profile reports 141

Report fields 142

Logs 147

14 Getting Help

If you need help from Tektronix 155

Using the automated fax systems 157

Receiving email update notices 158

15 Disabling Protocols

Disabling protocols: front panel 160

If the front panel is locked 167

Disabling protocols: PhaserShare Administrator 168

Disabling protocols: PhaserLink Printer Management Software 168

vi

PhaserShare Networking Manual

16 Resetting the Printer

Resetting the printer: PhaserLink Printer Management Software 169

Resetting your printer using the Apple Printer Utility 170

17 FTP Interface

Index

PhaserShare Networking Manual

1

Chapter

1

Network Printing with

Tektronix Color Printers

This manual provides information for system administrators and others who need to

install Tektronix Phaser 840, Phaser 740, Phaser 780, and Phaser 360 printers

equipped with PhaserShare Series B network interfaces.

■

Before using this manual, unpack and set up your printer. Install the

appropriate drivers on any PC and Macintosh computers on your network.

Instructions for unpacking, set-up, and installation are contained in your

printer’s user documentation.

■

After your printer is set up, use this manual in conjunction with your printer’s

PhaserShare Administrator or PhaserLink Printer Management Software to

conﬁgure the printer on the network.

This manual covers the following hardware and software versions:

■

PhaserShare Series B interfaces

■

PhaserShare Administrator version 3.9

Key components for networking Tektronix color printers

The following items are key components for networking your Tektronix printer:

■

PhaserShare Series B network interface.

This brings ease-of-use, superb

shareability and broad compatibility to Tektronix Phaser color printers. For

more information, see “PhaserShare Series B network interface” on page 2.

■

PhaserShare Administrator software.

PhaserShare Administrator

software makes it easy to install, conﬁgure, and manage Phaser printers on

a NetWare network. For more information, see Chapter 5, “PhaserShare

Administrator Software for NetWare Networks”.

■

PhaserLink Printer Management Software.

PhaserLink Printer

Management Software is internal printer software that provides printer

status and supports printer management through a World Wide Web

browser. For more information, see Chapter 12, “PhaserLink Printer

Management Software”.

■

PhaserPrint for UNIX software.

PhaserPrint for UNIX software provides a

driver with push-button control of printer features and fast raster ﬁle

printing capability from UNIX workstations. For more information, see

“Tektronix PhaserPrint for UNIX software” on page 10.

2

PhaserShare Networking Manual

1

Network Printing with Tektronix Color Printers

PhaserShare Series B network interface

The Phaser 840, 740, 780, and 360 printers support the PhaserShare Series B network

interface. These printers are equipped with a built-in PhaserShare Series B network

interface with a 10BaseT Ethernet connector. This printer can be equipped with

these optional PhaserShare Series B network cards:

■

PhaserShare Series B Fast Ethernet card.

This card is equipped with a

combined 10BaseT and 100BaseTx connector and a 10Base2 (BNC)

connector. The combined 10BaseT/100BaseTx connector can be connected

to either a 10BaseT or 100BaseTx network, and it will automatically adjust

to the correct data rate using a process called

auto-negotiation

. If no

connection is made to the 10BaseT/100BaseTx connector, the card is

prepared to communicate using the 10Base2 connector.

■

PhaserShare Series B Token Ring card.

This card is equipped with STP

(Shielded Twisted Pair) and UTP (Unshielded Twisted Pair) connectors.

Only one connector at a time can be used.

■

PhaserShare Series B LocalTalk card (AppleTalk).

PhaserShare network cards can be purchased initially with the printer as options or

added later as upgrade kits. A printer can have only one card at a time installed.

When a PhaserShare Series B Fast Ethernet or Token Ring card is installed, the

standard 10BaseT connector on the printer’s rear panel is disabled. The card and

the printer’s standard parallel port can be simultaneously active. All network

protocols can be simultaneously active.

PhaserShare cards

PhaserShare cards work with the following printers: Phaser 380, 350, 340, 560, 550,

540, and 600. PhaserShare cards enable you to use your printer with Ethernet, Token

Ring, LocalTalk, or serial connections. PhaserShare cards can be purchased initially

with the printer as options or added later as upgrade kits.

A printer can have only one PhaserShare card installed at a time. When a

PhaserShare card is installed, all ports on the card and the printer’s standard parallel

port can be simultaneously active. Also, all network protocols can be

simultaneously active.

For information on networking printers with PhaserShare cards, refer to the

PhaserShare Networking System Administrator Manual

, part number 070-9789-00.

PhaserShare Networking Manual

3

Network Printing with Tektronix Color Printers

1

Recognizing PhaserShare Series B interfaces and earlier PhaserShare cards

On your network, you may have some Tektronix printers equipped with

PhaserShare Series B interfaces and other Tektronix printers equipped with earlier

PhaserShare cards. Printers equipped with earlier PhaserShare cards are supported

differently in printer management software such as the PhaserShare Administrator

and PhaserLink Printer Management Software. There are several ways to determine

if the printer is equipped with a PhaserShare Series B interface or an earlier

PhaserShare card:

■

Printer model.

PhaserShare Series B cards work with Phaser 840, 740, 780,

and 360 printers. PhaserShare cards work with the following printers:

Phaser 380, 350, 340, 560, 550, 540, and 600.

■

Card rear panel.

The cards are labeled on the rear panel.

■

The printer’s Conﬁguration Page.

For Series B interfaces,

Series B

appears following the

Network Information

area on the printer’s

Conﬁguration Page. If an earlier PhaserShare card is installed, the printer’s

Conﬁguration Page reports the type of card installed in the

PhaserShare

ﬁeld.

■

The printer’s Startup Page.

For Series B interfaces,

Series B

appears in the

Ethernet

,

Token Ring

, or

LocalTalk

ﬁelds on the printer’s Startup Page. If

a PhaserShare card is installed, the printer’s Startup Page reports the

available connections in the

Ports

ﬁeld.

■

PhaserLink Printer Management Software.

If the

Adobe PostScript

ﬁeld

reads

Adobe PostScript Level 3 Version

, the interface is Series B. If the

ﬁeld reads

Adobe PostScript Level 2 Version

, the printer supports

PhaserShare network cards (not Series B). The

Adobe PostScript

ﬁeld is on

the

View Printer Information

page or on the

View and Conﬁgure General

Settings

page, depending on the printer type. Links to these pages can be

accessed by clicking the

Conﬁguration

link. For more information on

PhaserLink Printer Management Software, see Chapter 12, “PhaserLink

Printer Management Software”.

■

PhaserShare Administrator.

In the PhaserShare Administrator, Series B

interfaces are identiﬁed in the Ethernet or Token Ring tabs, where

Series B

is displayed in the

Interface Information

area. For more information on

the PhaserShare Administrator, see Chapter 5, “PhaserShare Administrator

Software for NetWare Networks”.

4

PhaserShare Networking Manual

1

Network Printing with Tektronix Color Printers

Environments supported

Tektronix Phaser printers are compatible with mixed PC, Macintosh, and UNIX

environments. The printer automatically switches between the printer’s ports and

network protocols to service all computers on the network.

Phaser printers are compatible with nearly all PC client/server environments. The

printer’s Ethernet and Token Ring network interfaces are compatible with the

following:

■

NetWare servers via the IPX (Internet Packet Exchange) protocol

■

Windows NT servers over TCP/IP or EtherTalk protocols

■

LANServer 4.0 servers via TCP/IP

■

UNIX workstation via TCP/IP

■

Macintosh computers via AppleTalk (LocalTalk, EtherTalk and TokenTalk).

■

Windows 98

■

Windows 95

Supported PC platforms

Any PC in the server environments listed in the previous topic, “Environments

supported,” can print over the network to a Phaser printer, including the following:

■

Windows 98

■

Windows 95

■

Windows 3.1

■

Windows NT

■

Windows for Workgroups

■

OS/2 Warp

■ DOS

PhaserShare Networking Manual

5

Network Printing with Tektronix Color Printers

1

Phaser printers are compatible with Banyan Vines and Microsoft LAN Manager

servers; however, third-party interfaces are required. Contact Tektronix Technical

Support for more information (see Chapter 14, “Getting Help”).

Workstations

UNIX

Macintosh

Windows 95

(peer - to - peer)

Server

Novell NetWare (IPX)

Windows NT (EtherTalk

or TCP/IP)

LAN Server 4.0 (TCIP/IP)

UNIX (TCP/IP)

Clients

Windows 95

Windows 3.1

Windows NT

Windows for Workgroups

OS/2 Warp

DOS

Phaser Color Printer

With PhaserShare

Ethernet or Token Ring

interface

9538-04c

6

PhaserShare Networking Manual

1

Network Printing with Tektronix Color Printers

Network installation overview

The printer’s Conﬁguration Page

Your printer can generate a Conﬁguration Page that lists the following information:

■ General printer information, including TekColor settings

■ Communication and network parameters for all ports

■ SCSI disk settings (if the printer has a SCSI port)

The information supplied on the Conﬁguration Page is helpful when you are

installing and conﬁguring the printer on a network. There are two ways to print the

Conﬁguration Page:

■ Use the printer’s front panel. You can easily print the Conﬁguration Page

from the printer’s front panel. Use this method if your printer is not yet

conﬁgured on the network. Refer to:

■ “Printing a Conﬁguration Page: Phaser 840 front panel” on page 7.

■ “Printing a Conﬁguration Page: Phaser 740 and 360 front panels” on

page 7.

■ “Printing a Conﬁguration Page: Phaser 780 front panel” on page 7.

■ Use PhaserLink Printer Management Software. With a TCP/IP

connection and a World Wide Web browser, you can use PhaserLink

Printer Management Software; see “Printing a Conﬁguration Page:

PhaserLink Printer Management Software” on page 7.

Step 1 Unpack and set up

the printer.

This step must be done before attempting to conﬁgure the printer on a network.

Printer setup includes installing ink or toner, loading paper trays, and turning on

the printer. See your printer’s user documentation for information about printer

setup.

Step 2 Install the network

card in the printer.

This step is necessary if the printer is to be equipped with an optional network

card. It is not necessary when using the printer’s built-in Ethernet connector.

This step is done at the factory when a network card is purchased initially with

your printer.

When a network card is purchased later as an upgrade kit, follow the

installation instructions included with the card.

Information on physically connecting the printer to networks is provided in this

manual:

For Ethernet, see “PhaserShare Series B Ethernet interface” on page 11.

For Token Ring, see “PhaserShare Series B Token Ring card” on page 14.

For LocalTalk, see “PhaserShare Series B LocalTalk card” on page 22.

Step 3 Network

conﬁguration.

For LocalTalk, EtherTalk, or TokenTalk, see Chapter 3, “EtherTalk, LocalTalk,

and TokenTalk Conﬁguration”.

For NetWare, see Chapter 4, “Novell NetWare Conﬁguration”.

For TCP/IP, see:

Chapter 6, “TCP/IP Conﬁguration Overview”.

Chapter 7, “TCP/IP Printer Conﬁguration (All Platforms)”.

Chapter 8, “TCP/IP Host Conﬁguration (UNIX)”.

Chapter 9, “TCP/IP Conﬁguration (OS/2 Warp/LAN Server)”

Chapter 11, “Windows 95 and Windows 98: PhaserPort Software”.

For Windows NT, see Chapter 10, “Windows NT”.

PhaserShare Networking Manual

7

Network Printing with Tektronix Color Printers

1

Printing a Conﬁguration Page: Phaser 840 front panel

1.

When the front panel displays READY TO PRINT, press the down-arrow

button until Menu is highlighted. Press Select.

2.

Press the down-arrow button until Printer Configuration is

highlighted. Press Select.

3.

Press the down-arrow button until Print Configuration Page is

highlighted. Press Select.

Printing a Conﬁguration Page: Phaser 740 and 360 front panels

1.

While Ready is displayed, press Menu; the printer displays the ﬁrst item

in the menu:

2.

Press Menu to access the Help Pages; the following message appears:

3.

Press <---- or ----> until the following message appears:

4.

Press Print.

Printing a Conﬁguration Page: Phaser 780 front panel

1.

While Ready is displayed, press Select; the Printer menu is

displayed:

2.

Press Menu; the Help Pages menu is displayed:

3.

Press Print.

Printing a Conﬁguration Page: PhaserLink Printer Management Software

1.

From the printer’s home page, click Conﬁguration; this displays the View

and Conﬁgure Settings page.

2.

On the View and Conﬁgure Settings page, select Conﬁguration Page

from the pull-down list. Click Print.

For more information on PhaserLink Printer Management Software, see Chapter 12,

“PhaserLink Printer Management Software”.

Help Pages

<---- ----> Menu

Menu Map

<---- ----> Print

Configuration Page

<---- ----> Print

Printer Menu

Help Pages Menu

Help Pages

Configuration Page Print

8

PhaserShare Networking Manual

1

Network Printing with Tektronix Color Printers

How to tell which protocols are enabled

All protocols can be enabled and disabled. The Conﬁguration Page reports which

protocols are enabled. If a protocol is enabled, the field for that protocol lists the

current parameters. If the protocol is disabled, the field for that protocol contains an

entry reading Disabled.

The printer’s networking software

The printer is shipped with a software CD-ROM, which contains software that you

may need to install your printer on a network. The CD-ROM also contains on-line

documentation, printer drivers, and other printer software. A single integrated

installer is used to install printer drivers and other software.

Obtaining networking software for Phaser 840, 740, and 780 printers

You obtain the networking software from the CD-ROM by running the installer:

1.

Insert the printer’s software CD-ROM into the CD-ROM drive.

■ If the Windows autorun feature is enabled, the CD-ROM launches

automatically.

■ If the Windows autorun feature is disabled, double-click My

Computer, then double click the CD icon to launch the CD-ROM.

2.

View the brief introductory information, then click Install Drivers to

launch the installer.

3.

When you are prompted to select Easy Install or Custom Install, select

Custom Install.

4.

In the Custom Install dialog box, check the box for Network Utilities.

5.

If you are running the installer on a computer that has NetWare software

installed, you can also check the boxes to install the PhaserShare

Administrator software. For more information on the PhaserShare

Administrator software, see Chapter 5, “PhaserShare Administrator

Software for NetWare Networks”.

6.

To complete the installation, follow the on-screen prompts.

PhaserShare Networking Manual

9

Network Printing with Tektronix Color Printers

1

Obtaining networking software for Phaser 360 printers

You obtain the networking software from the CD-ROM by running the installer:

1.

Locate and run the installer on the printer’s CD-ROM. On a PC, the ﬁle is

SETUP.EXE; on a Macintosh, it is Phaser 360 Installer.

2.

When you are prompted to select Easy Install or Custom Install,

select Custom Install.

3.

In the Custom Install dialog box, check the box for Network Utilities.

4.

If you are running the installer on a computer that has NetWare software

installed, you can also check the boxes to install the PhaserShare

Administrator software. For more information on the PhaserShare

Administrator software, see Chapter 5, “PhaserShare Administrator

Software for NetWare Networks”.

5.

To complete the installation, follow the on-screen prompts.

Network administration software

The following table lists the network administration software according to

environment (network protocol, platform, and printer).

Network administration software

Environment Software

NetWare; Windows 95,

Windows NT, and

Windows 3.1

Network queue conﬁguration: PhaserShare Administrator (Novell PCONSOLE

and NWAdmin can also be used.)

Printer conﬁguration: PhaserShare Administrator (Over TCP/IP, PhaserLink

Printer Management Software can also be used; Novell’s PCONSOLE and

NWAdmin cannot conﬁgure the PhaserShare network interface.)

Printer status monitoring: Windows Print Monitor (over TCP/IP, PhaserLink

Printer Management Software can also be used; PhaserLink Printer Management

Software provides status on additional Tektronix printer features.)

TCP/IP; Windows 95 and

Windows 3.1

Printer conﬁguration: PhaserLink Printer Management Software

Printer status monitoring: PhaserLink Printer Management Software

TCP/IP; Windows NT Printer conﬁguration: PhaserLink Printer Management Software (PhaserLink

Printer Management Software does not set up queues on the print server.)

Printer status monitoring: PhaserLink Printer Management Software

AppleTalk; Macintosh 7.x

and 8.x

Printer conﬁguration: PhaserLink Printer Management Software (MacTCP or

Open Transport required)

Printer status monitoring: PhaserLink Printer Management Software (MacTCP

or Open Transport required)

TCP/IP; UNIX Printer conﬁguration: PhaserLink Printer Management Software (If using

PhaserPrint for UNIX for printing, use PhaserPrint to set up print queues.)

Printer status monitoring: PhaserLink Printer Management Software

10

PhaserShare Networking Manual

1

Network Printing with Tektronix Color Printers

Support for DOS systems

For information on installing Tektronix printers in DOS environments, see the

printer’s CD-ROM. They contain PostScript utility ﬁles that can be sent to the

printer for network conﬁguration in DOS environments. They also contain a DOS

application, NWSET, for printer conﬁguration on NetWare networks.

For information on how to use the DOS conﬁguration ﬁles, see the README ﬁles on

the printer’s CD-ROM. PC users will ﬁnd the README ﬁle for the PostScript utility

ﬁles in the UTILS directory; the README ﬁle for NWSET is in the NETWARE

directory. (Macintosh users will ﬁnd the ReadMe ﬁle for the PostScript utility ﬁles in

the Network Utilities folder).

Tektronix PhaserPrint for UNIX software

For UNIX environments, Tektronix offers PhaserPrint software. PhaserPrint for

UNIX provides fast raster screen copy printing to Tektronix color printers.

PhaserPrint for UNIX also provides a graphical user interface for push-button

control of Tektronix printer features.

PhaserPrint for UNIX is available for these workstations:

■ Sun: SunOS 4.1.4, Solaris 2.3 and 2.4

■ SGI: IRIX 5.2, 5.3, 6.2, 6.3, and 6.4

■ HP 9000 700/800: HP-UX 9.0.5 and 10.2

■ IBM RS/6000: AIX 3.2 and 4.2

■ DECstation: ULTRIX 4.0 and 4.4

■ DEC Alpha AXP: OSF/1 3.0, 3.2, and Digital UNIX 4.0

PhaserPrint for UNIX works with the workstation’s native spooling system to print

PostScript ﬁles and raster ﬁles in these formats: Sun Raster Format (SRF), xwd, SGI

RGB, HP Starbase, TIFF, PBM, GIF, PCX, and BMP.

Your printer’s CD-ROM contains a demonstration copy of PhaserPrint for UNIX and

an on-line instruction guide in the unix/unixdemo directory. You can also obtain a

demonstration copy at this Tektronix site:

ftp.tek.com/cpid/UNIX/phaserprint2.1/demo

PhaserShare Networking Manual

11

Chapter

2

PhaserShare Series B

Network Interfaces

PhaserShare Series B network cards work with the Phaser 840, 740, 780, and 360

printers. Printers that work with PhaserShare Series B network cards have a built-in

PhaserShare Series B Ethernet interface on the rear panel. Earlier printers

(Phaser 380, 350, 340, 560, 550, 540, and 600) may be equipped with earlier

PhaserShare network cards; these printers have no built-in network connections on

the rear panel. If you are not sure which network interface your printer has, see

“Recognizing PhaserShare Series B interfaces and earlier PhaserShare cards” on

page 3.

This chapter provides information on connecting PhaserShare Series B interfaces to

the network; for information on installing PhaserShare Series B network cards, see

the instruction sheet that is shipped with each card.

PhaserShare Series B Ethernet interface

Ethernet is a communication standard that supports very high speed data

transmission. Ethernet offers signiﬁcant speed improvement compared to serial,

parallel, and LocalTalk connections. Speed improvement varies greatly depending

on network trafﬁc, computer hardware, and other factors.

The PhaserShare Series B Ethernet interface conforms to the IEEE 802.3 and Ethernet

II standards. With the printer’s built-in Ethernet interface, you can connect the

printer directly to an Ethernet network using twisted pair (10BaseT) cables. With the

PhaserShare Series B Ethernet card, you can connect the printer directly to an

Ethernet network using twisted pair (10BaseT or 100BaseTx) or thin coax (10Base2)

cables. Connecting the printer using thick coax (10Base5) requires an adapter;

contact your dealer to obtain adapters, cables, and terminators.

When a PhaserShare Series B Ethernet card is installed, the built-in Ethernet

connector is disabled; use the connectors on the card.

When a PhaserShare Series B card is purchased initially with the printer, it is

installed at the factory. When a PhaserShare Series B card is purchased later as an

upgrade kit, follow the instructions that are shipped with the card.

C

A

U

T

I

O

N

To avoid damaging the network interface, turn off the printer before making any

Ethernet connections.

12

PhaserShare Networking Manual

2

PhaserShare Series B Network Interfaces

Ethernet connections and indicators

The printer’s built-in Ethernet connector

The printer’s built-in Ethernet connector has the following connections and

indicators:

1.

LINK indicator (Phaser 360 only); on indicates a working connection to a

hub, off indicates no connection to a hub.

2.

RCV indicator (green); blinks while the network interface is receiving.

3.

XMT indicator (yellow); blinks while the network interface is transmitting.

4.

Twisted pair (10BaseT) connector.

PhaserShare Series B Ethernet card

The PhaserShare Series B Ethernet card has the following connections and

indicators:

1.

TX indicator (yellow); blinks while the network interface is transmitting.

2.

RX Link indicator (green); blinks while the network interface is receiving.

3.

Speed indicator (yellow); on indicates 100 Mbps, off indicates 10 Mbps.

4.

Twisted pair connection indicator; on indicates a working connection to a

hub, off indicates no connection to a hub. If the 10Base2 connector (

6

) is

used, this indicator is off.

5.

Twisted pair (10BaseT or 100BaseTx) connector.

6.

Thin coax (10Base2) connector.

0180-01

Ethernet

RCV XMT

LNK

1

2

4

3

9789-05

13 5 6

24

100

Mbs

10/100Base-TX

10Base2

TP

LINK

TX

RX

PhaserShare

TM

Series B

Ethernet Card

Page is loading ...

Tektronix Z780N - Phaser 780 Color Laser Printer Installation guide

Tektronix Z780N - Phaser 780 Color Laser Printer Installation guide

Related papers

Other documents