Creative TD020D User manual

GB

Cordless Impact Driver Instruction Manual

F Visseuse à chocs sans fil

Manuel d’instructions

D Akku-Schlagschrauber

Betriebsanleitung

I Avvitatore ad impulso a batteria

Istruzioni per l’uso

NL Accu-slagschroevendraaier

Gebruiksaanwijzing

E Atornillador de impacto a batería

Manual de instrucciones

P Berbequim de impacto a bateria

Manual de instruções

DK Akku slagskruetrækker

Brugsanvisning

S Sladdlös hammarskruvdragare

Bruksanvisning

N Batteridrevet slagtrekker

Bruksanvisning

FIN Iskevä akkuruuvinväännin

Käyttöohje

GR Ασύρµατ κρυστικ ιδτρύπαν δηγίες ρήσεως

TD020D

Page is loading ...

4

ENGLISH

Explanation of general view

1Button

2 Battery cartridge

3 Lock button

4 Switch

5 Lamp mark

6 Lamp

7Bit

8Sleeve

9 Bit-piece

10 Standard bolt

11 Fastening torque

12 Fastening time

13 Proper fastening torque

14 High tensile bolt

SPECIFICATION

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for screw driving in wood, metal and

plastic.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

SPECIFIC SAFETY RULES

GEB012-2

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict

adherence to impact driver safety rules. If you

use this tool unsafely or incorrectly, you can

suffer serious personal injury.

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

3. Hold the tool firmly.

4. Wear ear protectors.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious per-

sonal injury.

IMPORTANT SAFETY INSTRUCTIONS FOR

CHARGER & BATTERY CARTRIDGE

ENC007-2

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using bat-

tery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

Model TD020D

Capacities

Machine screw 3 mm – 8 mm

Standard bolt 3 mm – 8 mm

High tensile bolt 3 mm – 6 mm

Coarse thread 22 mm – 45 mm

No load speed (min

–1

)2,300

Impacts per minute 3,000

Overall length

Straight type 276 mm

Pistol type 213 mm

Net weight 0.53 kg

Rated voltage D.C. 7.2 V

5

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Lock button (Fig. 2)

When the lock button is in the locked position , the

switch cannot be actuated.

When the lock button is in the unlocked position , the

switch can be actuated.

Switch action (Fig. 3)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released.

To start the tool, first move the lock button to the released

position to release the switch. And then simply push

the switch on the side for the clockwise rotation and

the side for the counterclockwise rotation. Release

the switch to stop.

CAUTION:

• Always check the direction of rotation before operation.

• Change the direction only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always place the lock but-

ton in the locked position .

Lighting up the front lamp (Fig. 4 & 5)

CAUTION:

• Do not look in the light or see the source of light

directly.

To put on the light, first slide the lamp switch to the

position and then push the mark on the lamp switch.

Release it to stop.

NOTE:

• When the lamp switch is in the locked position ,

lamp switch cannot be actuated.

CAUTION:

• Always slide the lamp switch to the locked position

before storing the tool.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

ASSEMBLY

CAUTION:

• Always be sure that the lock button is in the locked

position mark and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit or socket bit

Use only the driver bit or socket bit shown in the figure.

(Fig. 6)

Do not use any other driver bit or socket bit.

For European and North & South American coun-

tries, Australia and New Zealand

For other countries

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit.

(Fig. 7)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 8)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

OPERATION

The tool can be used in two ways; a straight type and a

pistol type which is selectable according to the conditions

of workplace and screwdriving. (Fig. 9 & 10)

CAUTION:

• When bending the tool to use in the pistol type or

straightening to use in the straight type, do not hold the

bendable part of the tool. Failure to do so may cause

your hand and fingers to be pinched and injured by this

part.

Hold the tool firmly and place the point of the driver bit in

the screw head. Apply forward pressure to the tool to the

extent that the bit will not slip off the screw and turn the

tool on to start operation.

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. The relation between fas-

tening torque and fastening time is shown in the figures.

(Fig. 11 & 12)

A=12mm

B=9mm

Use only these types of bits. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A= 17mm

B= 14mm

To install these types of bits, follow the

procedure (1).

(Note) Makita bits are these types.

A= 12mm

B= 9mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for install-

ing the bit.

6

NOTE:

• Use the proper bit for the head of the screw/bolt that

you wish to use.

• Hold the tool pointed straight at the screw.

• If you tighten the screw for a time longer than shown in

the figures, the screw or the point of the driver bit may

be overstressed, stripped, damaged, etc. Before start-

ing your job, always perform a test operation to deter-

mine the proper fastening time for your screw.

The fastening torque is affected by a wide variety of fac-

tors including the following. After fastening, always check

the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

Using the tool as a hand screwdriver (Fig. 13)

Switch off the tool.

Move the lock button to the locked position .

Turn the tool.

NOTE:

• Use the tool with a fastening torque less than 12.5 Nm.

• This use is convenient for checking the screwdriving.

• Do not use the tool for work requiring excessive force,

such as tightening bolt M10 or bolts greater than M10

or removing rusted screws.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Phillips bit

• Socket bit

• Drill chuck attachment

• Soft carrying case

• Bit piece

• Various type of Makita genuine batteries and chargers

Page is loading ...

41

ENH102-5

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product

is in compliance with the following standards of standard-

ized documents,

EN60745, EN55014

in accordance with Council Directives, 89/336/EEC and

98/37/EC.

DÉCLARATION DE CONFORMITÉ CE

Nous déclarons sous notre entière responsabilité que ce

produit est conforme aux normes des documents stan-

dardisés suivants,

EN60745, EN55014

conformément aux Directives du Conseil, 89/336/CEE et

98/37/EG.

CE-KONFORMITÄTSERKLÄRUNG

Hiermit erklärt wir unter unserer alleinigen Verantwor-

tung, daß dieses Produkt gemäß den Ratsdirektiven 89/

336/EWG und 98/37/EG mit den folgenden Normen von

Normendokumenten übereinstimmen:

EN60745, EN55014.

DICHIARAZIONE DI CONFORMITÀ

CON LE NORME DELLA COMUNITÀ EUROPEA

Dichiariamo sotto la nostra sola responsabilità che

questo prodotto è conforme agli standard di documenti

standardizzati seguenti:

EN60745, EN55014

secondo le direttive del Consiglio 89/336/CEE e 98/37/

CE.

EG-VERKLARING VAN CONFORMITEIT

Wij verklaren hierbij uitsluitend op eigen verant-

woordelijkheid dat dit produkt voldoet aan de volgende

normen van genormaliseerde documenten,

EN60745, EN55014

in overeenstemming met de richtlijnen van de Raad 89/

336/EEC en 98/37/EC.

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra sola responsabilidad que este

producto cumple con las siguientes normas de docu-

mentos normalizados,

EN60745, EN55014

de acuerdo con las directivas comunitarias, 89/336/EEC

y 98/37/CE.

Yasuhiko Kanzaki

CE 2006

Director Amministratore

Directeur Directeur

Direktor Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes,

Bucks MK15 8JD, ENGLAND

Responsible manufacturer: Produttore responsabile:

Fabricant responsable

:

Verantwoordelijke fabrikant:

Verantwortlicher Hersteller: Fabricante responsable:

Makita Corporation Anjo Aichi Japan

ENGLISH

FRANÇAISE

DEUTSCH

ITALIANO

NEDERLANDS

ESPAÑOL

Page is loading ...

43

ENG004-2-V3

For European countries only

Noise and Vibration

The typical A-weighted sound pressure level is 85 dB (A).

Uncertainty is 3 dB (A).

The noise level under working may exceed 85 dB (A).

– Wear ear protection. –

The typical weighted root mean square acceleration

value is 4 m/s

2

.

These values have been obtained according to

EN60745.

Pour les pays d’Europe uniquement

Bruit et vibrations

Le niveau de pression sonore pondere type A est de

85 dB (A).

L’incertitude de mesure est de 3 dB (A).

Le niveau de bruit en fonctionnement peut dépasser

85 dB (A).

– Porter des protecteurs anti-bruit. –

L’accélération pondérée est de 4 m/s

2

.

Ces valeurs ont été obtenues selon EN60745.

Nur für europäische Länder

Geräusch- und Vibrationsentwicklung

Der typische A-bewertete Schalldruckpegel beträgt

85 dB (A).

Die Abweichung beträgt 3 dB (A).

Der Lärmpegel kann während des Betriebs 85 dB (A)

überschreiten.

– Gehörschutz tragen. –

Der gewichtete Effektivwert der Beschleunigung beträgt

4m/s

2

.

Diese Werte wurden gemäß EN60745 erhalten.

Modello per l’Europa soltanto

Rumore e vibrazione

Il livello di pressione sonora pesata secondo la curva A è

di 85 dB (A).

L’incertezza è di 3 dB (A).

Il livello di rumore durante il lavoro potrebbe superare gli

85 dB (A).

– Indossare i paraorecchi. –

Il valore quadratico medio di accellerazione è di 4 m/s

2

.

Questi valori sono stati ottenuti in conformità EN60745.

Alleen voor Europese landen

Geluidsniveau en trilling

Het typische A-gewogen geluidsdrukniveau is 85 dB (A).

Onzekerheid is 3 dB (A).

Tijdens het werken kan het geluidsniveau 85 dB (A) over-

schrijden.

– Draag oorbeschermers. –

De typische gewogen effectieve versnellingswaarde is

4m/s

2

.

Deze waarden werden verkregen in overeenstemming

met EN60745.

Para países europeos solamente

Ruido y vibración

El nivel de presión sonora ponderada A es de 85 dB (A).

Incerteza 3 dB (A).

El nivel de ruido en condiciones de trabajo puede que

sobrepase los 85 dB (A).

– Póngase protectores en los oídos. –

El valor ponderado de la aceleración es de 4 m/s

2

.

Estos valores han sido obtenidos de acuerdo con

EN60745.

ENGLISH

FRANÇAISE

DEUTSCH

ITALIANO

NEDERLANDS

ESPAÑOL

Page is loading ...

Creative TD020D User manual

Creative TD020D User manual

in other languages

Other documents