Lindy 25003 User manual

Lindy
Brand
Lindy
Model
25003
Category
Network switches
Type
User manual

This manual is also suitable for

Lindy 25003 is a high-performance Gigabit Ethernet switch ideal for small and medium networks or as a workgroup switch. It features 24x 10/100Base-TX, RJ-45 Fast Ethernet ports and 2x 10/100/1000Base-T, RJ-45 Gigabit Ethernet ports, providing plenty of connectivity options for your devices. The switch utilizes store & forward architecture that filters and forwards data after each packet is received and examined to be free of errors. All of the Fast Ethernet ports support full and half-duplex operation, and the Gigabit Ethernet ports support speeds of up to 1000Mbps.

Lindy 25003 is a high-performance Gigabit Ethernet switch ideal for small and medium networks or as a workgroup switch. It features 24x 10/100Base-TX, RJ-45 Fast Ethernet ports and 2x 10/100/1000Base-T, RJ-45 Gigabit Ethernet ports, providing plenty of connectivity options for your devices. The switch utilizes store & forward architecture that filters and forwards data after each packet is received and examined to be free of errors. All of the Fast Ethernet ports support full and half-duplex operation, and the Gigabit Ethernet ports support speeds of up to 1000Mbps.

24 + 2 GIGA Port
N-Way Switch
User Manual English
LINDY No. 25003
www.lindy.com
Introduction
Thank you for purchasing the LINDY 24+2 GIGA N-Way Switch. This
switch is a high performance Gigabit Ethernet switch which is ideal for
use in small and medium networks or as a workgroup switch.
The switch utilizes store & forward architecture that filters and forwards
data after each packet is received and examined to be free of errors. All
of the Fast Ethernet ports support full and half duplex operation. An auto-
negotiation function provides smooth migration from Ethernet over Fast
Ethernet to Gigabit Ethernet. The switch also supports back pressure
and IEEE 802.3x advanced flow control to reduce congestion and
prevent packet loss.
It features extensive LED’s allowing the operating status to be easily
monitored and can be mounted into a 19” rack using the supplied
brackets and screws.
Features
24 x 10/100Base-TX, RJ-45 Fast Ethernet ports
2 x 10/100/1000Base-T, RJ-45 Gigabit Ethernet ports
All ports support Auto-MDI/MDI-X function
Supports Full/Half-Duplex operation on all 10/100 ports
Extensive front panel diagnostic LED’s
Supports Store & Forward switching architecture
Wire-speed packet filtering and forwarding rate
Realtek 8326 chipset
19” rackmount design, brackets and screws included
Specifications
Standards: IEEE 802.3 (10Base-T), 802.3u (100Base-TX), 802.3ab
(1000Base-TX), 802.3x (Flow control support)
Switching Architecture: Store & Forward
Filter/Forward Rate: 14880pps (10Mbps), 148800pps (100Mbps),
1488100pps (Mbps)
MAC Address Table: 8K entries, self learning
Buffer Memory: 2.5Mbit
MDI / MDI-X function: all ports
N-Way Auto-negotiation: all ports
Full-Duplex/Half-Duplex: all ports
Chipset: Realtek 8326
Power supply: internal 3.3V 4A (100-240V / 50-60Hz, ~20Watts)
Dimensions (WxDxH): 440 x 135 x 44mm
Weight (approx.): 1.5kg (2.2kg incl. packaging)
Operating Temperature: 0°~50°C (32°~122°F)
Operating Humidity: 10%-90%, non-condensing
Package Contents
24+2 GIGA N-Way Switch
Power cable
19” rack mounting brackets and screws
Rubber feet
This manual
Front Panel
24 x 10/100 Ports
2 x 10/100/1000 Ports
24 x 10/100 Port
Link/Activity LED’s
Power LED
2 x 10/100/1000 Port
Link/Activity LED’s
LED Status Indicators
Type LED Status Description
Steady Green Power is on
System Power
Off Power is off
Steady Green
A valid link is
established
Flashing Green
Data packets
transmitted
Port 1-24
One LED per
port (10/100)
LINK/ACT
Off No link is established
Steady Green Port running at 10Mbps
10M
Off
No 10Base-T link is
established
Steady Green
Port running at
100Mbps
100M
Off
No 100Base-T link is
established
Steady Green
Port running at
1000Mbps
1000M
Off
No 1000Base-T link is
established
Green
Data packets
transmitted
Port 25,26 Four
LED’s per port
(10/100/1000)
ACT
Off No link is established
Installation
Operating Environment
This switch must be installed and operated within the specified
limits of the operating temperature and humidity as detailed in the
Specifications section
Do not place objects on top of the unit. Do not obstruct any vents at
the sides of the unit
Do not position the switch in direct exposure to the sun or near any
heat source such as a heater, radiator etc.
Prevent water and moisture entering the unit. If necessary use a
dehumidifier to reduce humidity
Connecting network devices
This switch features Auto MDI/MDI-X RJ-45 ports for easy connection to
other network devices using either a straight-through or crossover type
connecting cable.
1. Connect one end of the network cable to the RJ-45 port on the front
panel and connect the other end of the network cable to the RJ-45
port on the network device.
2. Follow the same procedure to connect each of the RJ-45 ports on
the switch.
3. The network cables must comply with EIA/TIA 568 specifications
and the Category 5 standard for 100Mbps data transmission
and at least Category 5e for 1000Mbps transmission.
4. The maximum length of any Ethernet segment is 100m. For
combined installations the 90m + 10m rule should be regarded
(90m with solid core installation cable + 10m for the patch cables).
Radio Frequency Energy, Certifications
FCC Certifications
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE Certification
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55024 and EN55022 class A for ITE,
EN61000-3-2/-3 the essential protection requirement of Council Directive
89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
LINDY No. 25003
www.lindy.com
1
st
Edition March 2005
  • Page 1 1
  • Page 2 2

Lindy 25003 User manual

Lindy
Brand
Lindy
Model
25003
Category
Network switches
Type
User manual
This manual is also suitable for

Lindy 25003 is a high-performance Gigabit Ethernet switch ideal for small and medium networks or as a workgroup switch. It features 24x 10/100Base-TX, RJ-45 Fast Ethernet ports and 2x 10/100/1000Base-T, RJ-45 Gigabit Ethernet ports, providing plenty of connectivity options for your devices. The switch utilizes store & forward architecture that filters and forwards data after each packet is received and examined to be free of errors. All of the Fast Ethernet ports support full and half-duplex operation, and the Gigabit Ethernet ports support speeds of up to 1000Mbps.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents