Hitachi CJ 14DSL Operating instructions

Category
Power tools
Type
Operating instructions

This manual is also suitable for

2
English
c) Prevent unintentional starting. Ensure the
switch is in the o position before connecting to
power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and o .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may a ect the
power toolʼs operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations di erent from
those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger speci ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of re when used with another
battery pack.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the in uence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
(Original instructions)
3
English
b) Use power tools only with speci cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
6) Service
a) Have your power tool serviced by a quali ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach of
children and in rm persons.
CORDLESS JIG SAW SAFETY
WARNINGS
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
ADDITIONAL SAFETY WARNINGS
1. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
2. Never disassemble the rechargeable battery and
charger.
3. Never short-circuit the rechargeable battery.
Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
4. Do not dispose of the battery in re. If the battery is burnt,
it may explode.
5. Do not insert object into the air ventilation slots of the
charger. Inserting metal objects or in ammables into the
charger air ventilation slots will result in electrical shock
hazard or damaged charger.
6. Bring the battery to the shop from which it was purchased
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
7. If the machine is used continuously at low speed, an
extra load is applied to the motor which can result in
motor seizure. Always operate the power tool so that
the blade is not caught by the material during operation.
Always adjust the blade speed to enable smooth cutting.
8. Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
9. Preparing and checking the work environment. Make
sure that the work site meets all the conditions laid forth
in the precautions.
10. Make sure that the battery is installed rmly. If it is at all
loose it could come o and cause an accident.
11. Dust produced in operation
The dust produced in normal operation may a ect
the operator’s health. Either of following way is
recommended.
a) Wear a dust mask
b) Use external dust collection equipment
When using the external dust collection equipment,
connect the adapter with the hose from external dust
collection equipment.
12. Changing blades
Be sure to switch power OFF and disconnect the battery
from the body when changing blades.
Do not open the lever when plunger is moving. (Fig. 3)
Con rm the protrusions of blade inserted to the blade
holder surely. (Fig. 3)
Con rm the blade located between the groove of roller.
(Fig. 3)
13. Always make sure to push in the lock o button to the
locked position when not using.
14 Do not look directly into the light from the LED lamp.
Continuous and direct exposure to the light from the LED
lamp can injure your eyes.
15. Using the splinter guard when cutting wood materials will
reduce splintering of cut surfaces.
Insert the splinter guard in the space on the base, and
push it completely.
16. Use chip cover
Chip cover prevents chips from ying o and improves
the e ciency of dust collector.
There is a possibility that chip cover is frosted when
cutting the metal.
17. Use sub base (sold separately)
Using the sub base made from steel will reduce abrasion
of aluminium base especially in cutting metals. Attach
the sub base to the bottom surface of base by attached 4
screws.
Using the sub base made from plastic will reduce
scratching of cut surface. Attach the sub base to the
bottom surface of base by attached 4 screws.
18. In order to prevent blade dislodging, damage or
excessive wear on the plunger, please make sure to
have surface of the base plate attached to the work piece
while sawing.
19 At low speed do not cut a wood with a thickness of more
than 10 mm or metal with a thickness of more than 1 mm.
20. To ensure accurate cutting when using the guide, always
set the orbital position to “0”.
21. When sawing a small circular arc, reduce the feeding
speed of the machine. If the machine is fed too fast, it
could cause the blade to break.
22. Circular cutting must be done with the blade
approximately vertical to the bottom surface of the base.
23. When cutting metallic materials, use an appropriate
cutting uid (spindle oil, soapy water, etc.) to prolong the
bladeʼs service life.
24. Angular cutting can not be done when adopting dust
collector.
25. Connecting with cleaner (sold separately)
By connecting with cleaner through dust collector (sold
separately) and adapter (sold separately), most of dust
can be collected.
4
English
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such a case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
During work make sure that swarf and dust do not fall on
the battery.
Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
Do not store an unused battery in a location exposed to
swarf and dust.
Before storing a battery, remove any swarf and dust that
may adhere to it and do not store it together with metal
parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject the
battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
speci ed.
7. If the battery charging fails to complete even when a
speci ed recharging time has elapsed, immediately stop
further recharging.
8. Do not put or subject the battery to high temperatures or
high pressure such as into a microwave oven, dryer, or
high pressure container.
9. Keep away from re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the rst time, do not use and return it to your
supplier or vendor.
WARNING
If a conductive foreign matter enters in the terminal of lithium
ion battery, the battery may be shorted, causing re. When
storing the lithium ion battery, obey surely the rules of
following contents.
Do not place conductive debris, nail and wires such as
iron wire and copper wire in the storage case.
To prevent shorting from occurring, load the battery in
the tool or insert securely the battery cover for storing
until the ventilator is not seen.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
CJ14DSL / CJ18DSL: Cordless Jig Saw
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V Rated voltage
n
0
No-load speed
Wood
Metal
Switching ON
Switching OFF
Disconnect the battery
Swtich lock
Switch unlock
Battery capacity
Remaining battery indicator switch
The battery remaining power is nearly empty.
Recharge the battery soonest possible
The battery remaining power is a half.
The battery remaining power is enough.
Prohibited action
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the
accessories listed on page 188.
Standard accessories are subject to change without notice.
5
English
APPLICATIONS
Cutting various lumber and pocket cutting
Cutting mild steel plate, aluminum plate, and copper
plate
Cutting synthetic resins, such as phenol resin and vinyl
chloride
Cutting thin and soft construction materials
Cutting stainless steel plate (with No. 97 blade)
SPECIFICATIONS
Model CJ14DSL CJ18DSL
Voltage 14.4 V 18 V
Max. cutting depth
Wood 135 mm
Mild steel 10 mm
No-load speed 0 2400 min
-1
Stroke 26 mm
Min. cutting radius 25 mm
Weight 2.3 kg 2.4 kg
NOTE
Due to HITACHI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect to the power source. (Fig. 2)
When charging the battery from an AC power source
Connect the charger’s power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1- second intervals).
CAUTION
Do not use the electrical cord if damaged. Have it
repaired immediately.
When charging the battery from a DC 12V in-car power
source (UC18YML2)
Secure the battery charger in place in the car.
Use the strap supplied with the battery charger to fasten
the battery charger in place and prevent it from moving
inadvertently. (See Fig. 18)
CAUTION
Do not place the battery charger or battery under the
driver’s seat. Secure the battery charger in place to
prevent it from moving inadvertently as this may lead
to an accident.
Fig. 18
Insert the cigarette lighter connecting plug into the
cigarette lighter socket.
If the plug is loose and falls out of the cigarette lighter
socket, repair the socket. As the socket may be faulty,
you are recommended to contact your local car dealer.
Continued use of the socket may result in an accident
due to overheating.
2. Insert the battery into the charger. (Fig. 2)
Firmly insert the battery into the charger.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously in
red.
When the battery becomes fully recharged, the pilot lamp
will blink in red. (At 1-second intervals) (See Table 1)
Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
Table 1
Indications of the pilot lamp
The pilot
lamp lights
or blinks.
Before charging Blinks (red)
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
While charging Lights (red)
Lights continuously
Charging
complete
Blinks (red)
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
Charging
impossible
Flickers (red)
Lights for 0.1 seconds. Does not light for 0.1
seconds. (o for 0.1 seconds)
Malfunction in the
battery or the charger
Overheat
standby
Lights (green)
(UC18YML2)
Lights continuously
Battery overheated.
Unable to charge.
(Charging will
commence when
battery cools)
Blinks (red)
(UC18YFSL)
Lights for 1 second. Does not light for 0.5
seconds. (o for 0.5 seconds)
Charging with in-
car power source
impossible
(UC18YML2)
Blinks (green)
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
Malfunction in the
battery or the charger
NOTE: When standby for cooling battery, UC18YML2 / UC18YFSL cools the overheated battery by cooling fan.
(However, the cooling fan does not function when charging the battery with a DC 12V in-car power source.)
6
English
NOTE
The recharging time may vary according to the ambient
temperature and power source voltage.
<UC18YML2>
Especially, using a DC 12V in-car power source may
require longer recharging time at high temperatures.
CAUTION
When the battery charger has been continuously used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next charging.
4. Disconnect the charger’s power cord from the
receptacle or cigarette lighter socket.
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use,
and then keep it.
CAUTION
If the battery is charged while it is heated because it has
been left for a long time in a location subject to direct
sunlight or because the battery has just been used,
the pilot lamp of the charger lights up green or lights
for 1 second, does not light for 0.5 seconds (o for
0.5 seconds). In such a case, rst let the battery cool,
then start charging.
When the pilot lamp ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
Since the built-in micro computer takes about 3
seconds to con rm that the battery being charged with
charger is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
Check the voltage of the in-car power source when
the pilot lamp ickers in green (every 0.2 seconds)
continuously. (UC18YML2)
If the voltage is 12V or lower, it indicates that the car
battery has weakened and cannot be charged.
Regarding the temperatures and charging time of the battery.
The temperatures and charging time will become as shown in Table 2.
Table 2
Charger
Battery
UC18YFSL
UC18YML2
(AC/DC)*
1
Charging voltage V 14.4 V – 18 V
Weight kg 0.5 0.7
Temperatures at which the battery can be
recharged
0oC – 50oC
Charging time for battery capacity, approx.
(At 20oC)
1.3 Ah
1.5 Ah
2.0 Ah
2.5 Ah
3.0 Ah
4.0 Ah
5.0 Ah
min.
min.
min.
min.
min.
min.
min.
20
22
30
35
45
60
75
20 / 50
22 / 60
30 / 80
35 / 100
45 / 120
60 / 160
75 / 200
Number of battery cells 4 – 10
*1 AC power supply / DC 12V (in-car) power supply
If the pilot lamp does not blink in red (every second) even
though the charger cord or cigarette lighter connecting
plug is connected to the power, it indicates that the
protection circuit of the charger may be activated.
Remove the cord or plug from the power and then
connect it again after 30 seconds or so. If this does
not cause the pilot lamp to blink in red (every second),
please take the charger to the Hitachi Authorized Service
Center.
MOUNTING AND OPERATION
Action Figure Page
Removing and inserting the battery 1 189
Charging 2 189
Changing blades 3 189
Switch operation 4 189
Remaining battery indicator 5 189
Adjusting the orbital operation 6 189
Splinter guard 7 190
Mounting and dismounting the chip
cover
8 190
Housing the hexagonal bar wrench
9 190
Mounting the guide (sold separately)
and rectilinear cutting
10 190
Mounting the guide (sold separately)
and cutting a circle or a circular arc
11 190
Cutting metallic materials 12 190
Angular cutting 13 191
Pocket cutting 14 191
Concerning cutting of stainless steel
plates
15 191
Connecting with cleaner 16 191
Sub base 17 191
Selecting accessories 192
7
English
SELECTION OF BLADES
To ensure maximum operating e ciency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut. The blade
number is engraved in the vicinity of the mounting portion
of each blade. Select appropriate blades by referring to
Table 3.
MAINTENANCE AND INSPECTION
CAUTION
Pull out battery before doing any inspection or
maintenance.
1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting e ciency and may cause overloading of
the motor. Replace the blade with a new one as soon as
excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
5. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Make sure that the battery is fully charged when stored
for a long period (3 months or more). The battery with
smaller capacity may not be able to be charged when
used, if stored for a long period.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage of batteries with a low charge
may result in performance deterioration, signi cantly
reducing battery usage time or rendering the batteries
incapable of holding a charge.
However, signi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
Important notice on the batteries for the Hitachi
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used with
batteries other than these designated by us, or when
the battery is disassembled and modi ed (such as
disassembly and replacement of cells or other internal
parts).
GUARANTEE
We guarantee Hitachi power tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the power tool, undismantled, with the GUARANTEE
CERTIFICATE
found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 95 dB (A).
Measured A-weighted sound pressure level: 84 dB (A).
Uncertainty K: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Cutting wood:
Vibration emission value a
h
, CW = 8.0 m/s
2
Uncertainty K = 4.6 m/s
2
Cutting sheet metal:
Vibration emission value
a
h
, CM = 5.2 m/s
2
Uncertainty K = 1.5 m/s
2
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.
WARNING
The vibration emission during actual use of the power
tool can di er from the declared total value depending in
the ways in which the tool is used.
Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched o and when it is running idle in addition to the
trigger time).
NOTE
Due to HITACHI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
8
English
Table 3 List of appropriate blades
Material to
be cut
Blade
Material quality
No. 1
(Super
long)
No. 11 No. 12 No. 15 No. 16 No. 21 No. 22 No. 41 No. 97
Thickness of material (mm)
Lumber
General lumber
Below 135
10 - 55 Below 20 10 - 55 5 - 40 10 - 65
Plywood 5 - 30 Below 10 5 - 30 3 - 20
Iron plate
Mild steel plate 3 - 6 Below 3 2 - 5
Stainless steel
plate
1.5 - 2.5
Nonferrous
metal
Aluminium
copper, brass
3 - 12 Below 3 Below 5
Aluminium sash
Height up
to 25
Height up
to 25
Plastics
Phenol resin,
melamine, resin,
etc.
5 - 20 Below 6 5 - 15 Below 6 5 - 15
Vinyl chloride,
acryl resin, etc.
5 - 30 Below 10 5 - 20 Below 5 5 - 30 3 - 20 5 - 15
Foamed
polyethylene,
foamed styrol
10 - 55 3 - 25 5 - 25 3 - 25 10 - 55 3 - 40 5 - 25
Pulp
Card board,
corrugated paper
10 - 55 3 - 25 10 - 55 3 - 40
Hardboard 3 - 25 Below 6 3 - 25
Fiberboard Below 6
NOTE
The minimum cutting radius of No. 1 (Super long), No. 21, No. 22 and No. 41 blades is 100 mm.
188
No.41
CJ14DSL
CJ18DSL
111 1 2 1 1 1
CJ14DSL
(NN)
CJ18DSL
(NN)
111 1 ――
189
12
34
56
1
1
1
1 1
2
2
2
2
2
0
2400min
-1
<UC18YML2>
<UC18YFSL>
26 mm
193
English Dansk Română
GUARANTEE CERTIFICATE
1 Model No.
2 Serial No.
3 Date of Purchase
4 Customer Name and Address
5 Dealer Name and Address
(Please stamp dealer name and address)
GARANTIBEVIS
1 Modelnummer
2 Serienummer
3 Købsdato
4 Kundes navn og adresse
5 Forhandlers navn og adresse
(Indsæt stempel med forhandlers navn og
adresse)
CERTIFICAT DE GARANŢIE
1 Model nr.
2 Nr. de serie
3 Data cumpărării
4 Numele și adresa clientului
5 Numele și adresa distribuitorului
(Vă rugăm aplicaţi ștampila cu numele și adresa
distribuitorului)
Deutsch Norsk Slovenščina
GARANTIESCHEIN
1 Modell-Nr.
2 Serien-Nr.
3 Kaufdaturn
4 Name und Anschrift des Kunden
5 Name und Anschrift des Händlers
(Bitte mit Namen und Anschrift des Handlers
abstempeln)
GARANTISERTIFIKAT
1 Modellnr.
2 Serienr.
3 Kjøpsdato
4 Kundens navn og adresse
5 Forhandlerens navn og adresse
(Vennligst stemple forhandlerens navn og adresse)
GARANCIJSKO POTRDILO
1 Št. modela
2 Serijska št.
3 Datum nakupa
4 Ime in naslov kupca
5 Ime in naslov prodajalca
(Prosimo vtisnite žig z imenom in naslovom
prodajalca)
Français Suomi Slovenčina
CERTIFICAT DE GARANTIE
1 No. de modèle
2 No de série
3 Date dʼachat
4 Nom et adresse du client
5 Nom et adresse du revendeur
(Cachet portant le nom et lʼadresse du revendeur)
TAKUUTODISTUS
1 Malli nro
2 Sarja nro
3 Ostopäivämäärä
4 Asiakkaan nimi ja osoite
5 Myyjän nimi ja osoite
(Leimaa myyjän nimi ja osoite)
ZÁRUČNÝ LISTA
1 Č. modelu
2 Sériové č.
3 Dátum zakúpenia
4 Meno a adresa zákazníka
5 Názov a adresa predajcu
(Pečiatka s názvom a adresou predajcu)
Italiano Ελληνικά Български
CERTIFICATO DI GARANZIA
1 Modello
2 N° di serie
3 Data di acquisto
4 Nome e indirizzo dellʼacquirente
5 Nome e indirizzo del rivenditore
(Si prega di apporre il timbro con questi dati)
ΠΙΣΤΟΠΟΙΗΤΙΚΟ ΕΓΓΥΗΣΗΣ
1 Αρ. Μοντέλου
2 Αύξων Αρ.
3 Ημερομηνία αγοράς
4 Όνομα και διεύθυνση πελάτη
5 Όνομα και διεύθυνση μεταπωλητή
(Παρακαλούμε να χρησιμοποιηθεί σφραγίδα)
ГАРАНЦИОНЕН СЕРТИФИКАТ
1 Модел
2 Сериен
3 Дата за закупуване
4 Име и адрес на клиента
5 Име и адрес на търговеца
(Моля, отпечатайте името и адрес на дилъра)
Nederlands Polski Srpski
GARANTIEBEWIJS
1 Modelnummer
2 Serienummer
3 Datum van aankoop
4 Naam en adres van de gebruiker
5 Naam en adres van de handelaar
(Stempel a.u.b. naam en adres vande de
handelaar)
GWARANCJA
1 Model
2 Numer seryjny
3 Data zakupu
4 Nazwa klienta i adres
5 Nazwa dealera i adres
(Pieczęć punktu sprzedaży)
GARANTNI SERTIFIKAT
1 Br. modela.
2 Serijski br.
3 Datum kupovine
4 Ime i adresa kupca
5 Ime i adresa prodavca
(Molimo da stavite pečat na ime i adresu trgovca)
Español Magyar Hrvatski
CERTIFICADO DE GARANTÍA
1 Número de modelo
2 Número de serie
3 Fecha de adquisición
4 Nombre y dirección del cliente
5 Nombre y dirección del distribudor
(Se ruega poner el sello del distribudor con su
nombre y dirección)
GARANCIA BIZONYLAT
1 Típusszám
2 Sorozatszám
3 A vásárlás dátuma
4 A Vásárló neve és címe
5 A Kereskedő neve és címe
(Kérjük ide elhelyezni a Kereskedő nevének és
címének pecsétjét)
JAMSTVENI CERTIFIKAT
1 Br modela.
2 Serijski br.
3 Datum kupnje
4 Ime i adresa kupca
5 Ime i adresa trgovca
(Molimo stavite pečat na ime i adresu trgovca)
Português Čeština Український
CERTIFICADO DE GARANTIA
1 Número do modelo
2 Número do série
3 Data de compra
4 Nome e morada do cliente
5 Nome e morada do distribuidor
(Por favor, carímbe o nome e morada do
distribuidor)
ZÁRUČNÍ LIST
1 Model č.
2 Série č.
3 Datum nákupu
4 Jméno a adresa zákazníka
5 Jméno a adresa prodejce
(Prosíme o razítko se jménem a adresou prodejce)
ГАРАНТІЙНИЙ СЕРТИФІКАТ
1 моделі
2 серії
3 Дата придбання
4 Ім'я і адреса клієнта
5 Ім'я і адреса дилера
(Будь ласка, поставте печатку з іменем і
адресою дилера)
Svenska Türkçe Русский
GARANTICERTIFIKAT
1 Modellnr
2 Serienr
3 Inköpsdatum
4 Kundens namn och adress
5 Försäljarens namn och adress
(Stämpla försäljarens namn och adress)
GARANTİ SERTİFİKASI
1 Model No.
2 Seri No.
3 Satın Alma Tarihi
4şteri Adı ve Adresi
5 Bayi Adı ve Adresi
(Lütfen bayi adını ve adresini kaşe olarak basın)
ГАРАНТИЙНЫЙ СЕРТИФИКАТ
1 Модель
2 Серийный
3 Дата покупки
4 Название и адрес заказчика
5 Название и адрес дилера
(Пожалуйста, внесите название и адрес дилера)
195
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 willich, Germany
Tel: +49 2154 49930
Fax: +49 2154 499350
URL: http://www.hitachi-powertools.de
Hitachi Power Tools Netherlands B. V.
Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands
Tel: +31 30 6084040
Fax: +31 30 6067266
URL: http://www.hitachi-powertools.nl
Hitachi Power Tools (U. K.) Ltd.
Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ,
United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hitachi-powertools.co.uk
Hitachi Power Tools France S. A. S.
Parc de l’Eglantier 22, rue des Cerisiers, Lisses-C.E. 1541,
91015 EVRY CEDEX, France
Tel: +33 1 69474949
Fax: +33 1 60861416
URL: http://www.hitachi-powertools.fr
Hitachi Power Tools Belgium N.V. / S.A.
Koningin Astridlaan 51, B-1780 Wemmel, Belgium
Tel: +32 2 460 1720
Fax: +32 2 460 2542
URL http://www.hitachi-powertools.be
Hitachi Fercad Power Tools Italia S.p.A
Via Retrone 49, 36077, Altavilla Vicentina (VI), Italy
Tel: +39 0444 548111
Fax: +39 0444 548110
URL: http://www.hitachi-powertools.it
Hitachi Power Tools lberica, S.A.
Puigbarral, 26-28 Pol. Ind. Can Petit 08227
TERRSSA(Barcelona) Spain
Tel: +34 93 735 6722
Fax: +34 93 735 7442
URL: http://www.hitachi-powertools.es
Hitachi Power Tools Österreich GmbH
Str. 7, Objekt 58/A6, Industriezentrum NÖ Süd 2355
Wiener Neudorf, Austria
Tel: +43 2236 64673/5
Fax: +43 2236 63373
URL: http://www.hitachi-powertools.at/
Hitachi Power Tools Norway AS
Kjeller Vest 7, N-2007 Kjeller, Norway
Tel: (+47) 6692 6600
Fax: (+47) 6692 6650
URL: http://www.hitachi-powertools.no
Hitachi Power Tools Sweden AB
Rotebergsvagen 2B SE-192 78 Sollentuna, Sweden
Tel: (+46) 8 598 999 00
Fax: (+46) 8 598 999 40
URL: http://www.hitachi-powertools.se
Hitachi Power Tools Denmark A/S
Lillebaeltsvej 90, 6715 Esbjerg N, Denmark
Tel: (+45) 75 14 32 00
Fax: (+45) 75 14 36 66
URL: http://www.hitachi-powertools.dk
Hitachi Power Tools Finland Oy
Tupalankatu 9, 15680 Lahti, Finland
Tel: (+358) 20 7431 530
Fax: (+358) 20 7431 531
URL: http://www.hitachi-powertools.
Hitachi Power Tools Hungary Kft.
1106 Bogancsvirag U.5-7, Budapest, Hungary
Tel: +36 1 2643433
Fax: +36 1 2643429
URL: http://www.hitachi-powertools.hu
Hitachi Power Tools Polska Sp.z o.o.
ul. Gierdziejewskiego 1
02-495 Warszawa, Poland
Tel: +48 22 863 33 78
Fax: +48 22 863 33 82
URL: http://www.hitachi-narzedzia.pl/
Hitachi Power Tools Czech s.r.o.
Modricka 205, 664, 48, Moravany, Czech, Republic
Tel: +420 547 422 660
Fax: +420 547 213 588
URL: http://www.hitachi-powertools.cz
Hitachi Power Tools Netherlands B.V.
Moscow Branch
Kashirskoye Shosse Dom 65, 4F
115583 Moscow, Russia
Tel: +7 495 727 4460
Fax: +7 495 727 4461
URL: http://www.hitachi-pt.ru
Hitachi Power Tools Romania S. R. L.
Bld. Biruintei, Nr. 101, Oras Pentelimon, 077145, Judetul
Ilfov, ROMANIA
Tel: +031 805 27 19
Fax: +031 805 25 77
198
English Nederlands
Object of declaration: Hitachi Cordless Jig Saw CJ14DSL, CJ18DSL
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with standards or standardization documents EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-
2 and EN61000 in accordance with Directives 2004/108/EC and
2006/42/EC. This product also conforms to RoHS Directive 2011/65/
EU.
The European Standards Manager at Hitachi Koki Europe Ltd. is
authorized to compile the technical le.
This declaration is applicable to the product a xed CE marking.
Onderwerp van verklaring: Hitachi Snoerloze
decoupeerzaagmachine CJ14DSL,
CJ18DSL
EC VERKLARING VAN CONFORMITEIT
Wij verklaren onder eigen verantwoordelijkheid dat dit product
conform de richtlijnen of gestandardiseerde documenten EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2
en EN61000 voldoet aan de eisen van bepalingen 2004/108/EC en
2006/42/EC. Dit product voldoet ook aan de RoHS-richtlijn 2011/65/
EU.
De manager voor Europese normen van Hitachi Koki Europe Ltd.
heeft de bevoegdheid tot het samenstellen van het technische
bestand.
Deze verklaring is van toepassing op produkten voorzien van de CE-
markeringen.
Deutsch Español
Gegenstand der Erklärung: Hitachi Akku-Stichsäge CJ14DSL,
CJ18DSL
EG-KONFORMITÄTSERKLÄRUNG
Wir erklären mit alleiniger Verantwortung, dass dieses Produkt
den Standards oder Standardisierungsdokumenten EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2
und EN61000 in Übereinstimmung mit den Direktiven 2004/108/EG
und 2006/42/EG entspricht. Dieses Produkt stimmt auch mit der
RoHS-Richtlinie 2011/65/EU überein.
Der Manager für europäische Standards bei der Hitachi Koki Europe
Ltd. ist zum Verfassen der technischen Datei befugt.
Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.
Objeto de declaración: Hitachi Sierra de calar a batería CJ14DSL,
CJ18DSL
DECLARACIÓN DE CONFORMIDAD DE LA CE
Declaramos bajo nuestra única responsabilidad que este producto
está de acuerdo con las normas o con los documentos de
normalización EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-
29, EN55014-1, EN55014-2 y EN61000, según indican las Directrices
2004/108/CE y 2006/42/CE. Este producto satisface también los
requisitos establecidos por la Directiva 2011/65/EU (RoHS).
El Jefe de Normas Europeas de Hitachi Koki Europe Ltd. está
autorizado para recopilar archivos técnicos.
Esta declaración se aplica a los productos con marcas de la CE.
Français Português
Objet de la déclaration: Hitachi Scie sauteuse à batterie CJ14DSL,
CJ18DSL
DECLARATION DE CONFORMITE CE
Nous déclarons sous notre seule et entière responsabilité que ce
produit est conforme aux normes ou documents de normalisation
EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1,
EN55014-2 et EN61000 en accord avec les Directives 2004/108/CE
et 2006/42/CE. Ce produit est aussi conforme à la Directive RoHS
2011/65/EU.
Le responsable des normes européennes d’Hitachi Koki Europe Ltd.
est autorisé à compiler les données techniques.
Cette déclaration s’applique aux produits désignés CE.
Objeto de declaração: Hitachi Serra de recortes a bateria CJ14DSL,
CJ18DSL
DECLARAÇÃO DE CONFORMIDADE CE
Declaramos, sob nossa única e inteira responsabilidade, que este
produto está de acordo com as normas ou documentos normativos
EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-
1, EN55014-2 e EN61000, em conformidade com as Directrizes
2004/108/CE e 2006/42/CE. Este produto está também em
conformidade com a Directiva RoHS 2011/65/EU.
O Gestor de Normas Europeias da Hitachi Koki Europe Ltd. está
autorizado a compilar o cheiro técnico.
Esta declaração se aplica aos produtos designados CE.
Italiano Svenska
Oggetto della dichiarazione: Hitachi Seghetto alternativo a batteria
CJ14DSL, CJ18DSL
DICHIARAZIONE DI CONFORMITÀ CE
Dichiariamo sotto nostra responsabilità che questo prodotto è
conforme agli standard o ai documenti sulla standardizzazione
EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1,
EN55014-2 e EN61000 in conformità alle Direttive 2004/108/CE
e 2006/42/CE. Il prodotto è inoltre conforme alla direttiva RoHS
2011/65/EU.
Il Responsabile delle Norme Europee di Hitachi Koki Ltd. è autorizzato
a compilare la scheda tecnica.
Questa dichiarazione è applicabile ai prodotti cui sono applicati i
marchi CE.
Objekt för deklaration: Hitachi Batteridriven Sticksåg CJ14DSL,
CJ18DSL
EF-DEKLARATION BETRÄFFANDE LIKFORMIGHET
Vi tillkännagiver med eget ansvar att denna produkt överensstämmer
med standard eller standardiserings dokument EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2
och EN61000 i enlighet med direktiven 2004/108/EF och 2006/42/EF.
Denna produkt efterlever även RoHS-direktiv 2011/65/EU.
Den europeiska standardansvarige på Hitachi Koki Europe Ltd. är
auktoriserad att utarbeta den tekniska len.
Denna deklaration gäller för CE-märkningen pà produkten.
Hitachi Koki Europe Ltd.
Clonshaugh Business & Technology Park, Dublin 17, lreland
28. 9. 2014
John de Loughry
European Standard Manager
28. 9. 2014
A. Yoshida
Vice-President & Director
Representative o ce in Europe
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 Willich 1, F. R. Germany
Head o ce in Japan
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
199
Dansk Polski
Genstand for erklæring: Hitachi Akku stiksav CJ14DSL, CJ18DSL
EF-OVERENSS TEMMELSESERKLÆRING
Vi erlkærer os fuldstændige ansvarlige for, at dette produkt modsvarer
gældende standard eller standardiserings dokumenter EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-
2 og EN61000 i overensstemmelse med direktiver 2004/108/EF og
2006/42/EF. Dette produkt er også i overensstemmelse med RoHS
direktiv 2011/65/ EU.
Chefen for europæiske standarder hos Hitachi Koki Europe Ltd. er
autoriseret til at kompilere den tekniske l.
Denne erklæring qælder produkter, der er mærket med CE.
Przedmiot deklaracji: Hitachi Wyrzynarka bateryjna CJ14DSL,
CJ18DSL
DEKLARACJA ZGODNOŚCI Z EC
Oznajmiamy z całkowitą odpowiedzialnością, że produkt ten jest
zgodny ze standardami lub standardowymi dokumentami EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2
i EN61000 w zgodzie z Zasadami 2004/108/EC i 2006/42/EC. Ten
produkt spełnia także wymagania Dyrektywy RoHS 2011/65/EU.
Menedżer Standardów Europejskich w rmie Hitachi Koki Europe Ltd.
Jest upoważniony do kompilowania pliku technicznego.
To oświadczenie odnosi się do załączonego produktu z oznaczeniami
CE.
Norsk Magyar
Erklæringens objekt: Hitachi Stikksag Elektrisk slagboremaskin
CJ14DSL, CJ18DSL
EF’S ERKLÆRING OM OVERENSSTEMMELSE
Vi erklærer herved at vi påtar oss det fulle ansvar for at dette produktet er
i overensstemmelse med normer eller standardiseringsdokumentene
EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-
1, EN55014-2 og EN61000 i samsvar med direktivene 2004/108/
EF og 2006/42/EF. Dette produktet er også i samsvar med RoHS-
direktivet 2011/65/EU.
Lederen for europeiske standarder ved Hitachi Koki Europe Ltd. har
fullmakt til å utarbeide det tekniske dokumentet.
Denne erklæringen gjelder produktets påklistrede CE-merking.
Megfelelőségi nyilatkozat: Hitachi Akkus szúrófűrész CJ14DSL,
CJ18DSL
EK MEGFELELŐSÉGI NYILATKOZAT
Teljes felelősségünk tudatában kijelentjük, hogy ez a termék
megfelel az EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29,
EN55014-1, EN55014-2, és EN61000 szabványoknak illetve
szabványosítási dokumentumoknak, az Európa Tanács 2004/108/EK
és 2006/42/EK Direktíváival összhangban. Ez a termék is megfelel a
2011/65/EU RoHS irányelvnek.
Az Hitachi Koki Europe Ltd. Európai Szabványkezelője fel van
hatalmazva a műszaki fájl elkészítésére.
Jelen nyilatkozat a terméken feltüntetett CE jelzésre vonatkozik.
Suomi Čeština
Ilmoituksen kohde: Hitachi Akkupistosaha CJ14DSL, CJ18DSL
EY-ILMOITUS YHDENMUKAISUUDESTA
Yksinomaisella vastuudella vakuutamme, että tämä tuote vastaa tai
normitettuja dokumentteja EN60745-1, EN60745-2-11, EN60335-1,
EN60335-2-29, EN55014-1, EN55014-2 ja EN61000 ohjeiden
2004/108/EY ja 2006/42/EY mukaisesti. Tämä tuote on myös RoHS-
direktiivin (2011/65/EU) mukainen.
Hitachi Koki Europe Ltd.:n eurooppalaisten standardien johtaja on
valtuutettu laatimaan tekniset asiakirjat.
Tämä ilmoitus sovelletaan tuotekohtaiseen CE-merkintään.
Předmět prohlášení: Hitachi Akku přímočará pila CJ14DSL, CJ18DSL
PROHLÁŠENÍ O SHODĚ S CE
Prohlašujeme na svoji zodpovědnost, že tento výrobek odpovídá
normám EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-
29, EN55014-1, EN55014-2 a EN61000 v souladu se směrnicemi
2004/108/EC a 2006/42/EC. Tento výrobek je rovněž v souladu se
směrnicí RoHS 2011/65/EU.
Vedoucí pracovník pro Evropské normy v Hitachi Koki Europe Ltd. je
oprávněný ke zpracování technického souboru.
Toto prohlášení platí pro výrobek označený značkou CE.
Ελληνικά Türkçe
Αντικείμενο δήλωσης: Hitachi Σέγα μπαταρίας CJ14DSL, CJ18DSL
EK ΔΗΛΩΣΗ ΕΝΑΡΜΟΝΙΣΜΟΥ
Δηλώνουμε με απόλυτη υπευθυνότητα ότι αυτό το προιόν
είναι εναρμονισμένο με τα πρότυπα ή τα έγραφα δημιουργίας
προτύπων EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29,
EN55014-1, EN55014-2 και EN61000 σε συμφωνία με τις Οδηγίες
2004/108/EK και 2006/42/EK. Αυτό το προϊόν συμμορφώνεται
επίσης με την οδηγία RoHS 2011/65/EU.
Ο υπεύθυνος για τα ευρωπαϊκά πρότυπα στην Hitachi Koki Europe
Ltd. είναι εξουσιοδοτημένος να συντάσσει τον
τεχνικό φάκελο.
Αυτή η δήλωση ισχύει στο προιόν με το σημάδι CE.
Beyan konusu: Hitachi Akülü dekupaj testere CJ14DSL, CJ18DSL
AB UYGUNLUK BEYANI
Bu ürünün, 2004/108/EC, 2006/42/EC sayılı Direkti erine uygun
olarak, EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-
29, EN55014-1, EN55014-2 ve EN61000 sayılı standartlara ve
standardizasyon belgelerine uygun olduğunu, tamamen kendi
sorumluluğumuz altında beyan ederiz. Bu ürün, ayrıca RoHS
Yönergesi 2011/65/EU'ya uygundur.
Hitachi Koki Europe Ltd. Avrupa Standartlar Müdürü, teknik dosyayı
hazırlama yetkisine sahiptir.
Bu beyan, üzerinde CE işareti bulunan ürünler için geçerlidir.
Hitachi Koki Europe Ltd.
Clonshaugh Business & Technology Park, Dublin 17, lreland
28. 9. 2014
John de Loughry
European Standard Manager
28. 9. 2014
A. Yoshida
Vice-President & Director
Representative o ce in Europe
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 Willich 1, F. R. Germany
Head o ce in Japan
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
Română Srpski
Obiectul declaraţiei: Hitachi Fierastrau pendular cu acumulator
CJ14DSL, CJ18DSL
DECLARAŢIE DE CONFORMITATE CE
Declarăm pe propria răspundere că acest produs este conform
cu standardele sau documentele de standardizare EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-
2 şi EN61000 şi cu Directivele 2004/108/CE şi 2006/42/CE. Acest
produs este, de asemenea, conform cu Directiva RoHS 2011/65/EU.
Managerul pentru standarde euopene al Hitachi Koki Europe Ltd. este
autorizat să întocmească şa tehnică.
Prezenta declaraţie se referă la produsul pe care este aplicat semnul
CE.
Predmet deklaracije:
Hitachi Bežična testera za bušenje CJ14DSL,
CJ18DSL
EC DEKLARACIJA O SAOBRAZNOSTI
Pod punom odgovornošću izjavljujemo da je ovaj proizvod
usklađen s normama i dokumentima za standardizaciju EN60745-1,
EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2
i EN61000 shodno Direktivama 2004/108/EC i 2006/42/EC. Ovaj
proizvod je takođe usklađen sa RoHS Direktivom 2011/65/EU.
Direktor za evropske standarde u kompaniji Hitachi Koki Europe Ltd.
ovlašćen je za sastavljanje tehničke dokumentacije.
Ova izjava se odnosi na proizvod na koji je stavljena CE oznaka.
Slovenščina Hrvatski
Predmet deklaracije: Hitachi Akumulatorska vbodna žaga CJ14DSL,
CJ18DSL
ES IZJAVA O SKLADNOSTI
Po lastni odgovornosti objavljamo, da je izdelek v skladu s standardi
ali dokumenti za standardizacijo EN60745-1, EN60745-2-11,
EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 in EN61000
v skladu z direktivami 2004/108/ES in 2006/42/ES. Za izdelek je
skladen tudi z direktivo RoHS 2011/65/EU.
Direktor za evropske standarde podjetja Hitachi Koki Europe Ltd. je
pooblaščen za sestavljanje tehničnih datotek.
Deklaracija je označena na izdelku s pritrjeno CE označbo.
Predmet deklaracije:
Hitachi Bežična ubodna pila CJ14DSL,
CJ18DSL
EC IZJAVA O SUKLADNOSTI
Izjavljujemo s punom odgovornošću da je ovaj proizvod sukladan
normama i dokumentima za standardizaciju EN60745-1, EN60745-2-
11, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 i EN61000
sukladno Direktivama 2004/108/EC i 2006/42/EC. Ovaj proizvod je
također sukladan RoHS Direktivi 2011/65/EU.
Direktor za europske standarde u poduzeću Hitachi Koki Europe Ltd.
ovlašten je za sastavljanje tehničke dokumentacije.
Ova izjava se primjenjuje na proizvod na kojem je stavljena CE
oznaka.
Slovenčina Український
Predmet vyhlásenia: Hitachi Akumulátorová priamočiara píla
CJ14DSL, CJ18DSL
VYHLÁSENIE O ZHODE - EC
Týmto vyhlasujeme na našu vlastnú zodpovednosť že tento výrobok
je v zhode s nasledujúcimi normami a dokumentmi normalizácie,
EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1,
EN55014-2 a EN61000 a v súlade so smernicami 2004/108/ES a
2006/42/ES. Tento výrobok vyhovuje tiež smernici RoHS č. 2011/65/
EU.
Za zostavenie technického súboru je zodpovedný manažér pre
európske normy spoločnosti Hitachi Koki Europe Ltd.
Toto vyhlásenie sa vzťahuje na výrobok označený značkou CE.
Предмет декларування:
Hitachi Акумуляторна ножівкова пилка
CJ14DSL, CJ18DSL
ДЕКЛАРАЦІЯ ВІДПОВІДНОСТІ ЕС
Ми декларуємо, що цей виріб відповідає стандартам або
стандартизаційним документам EN60745-1, EN60745-2-11,
EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 і EN61000
згідно Директив 2004/108/EC і 2006/42/EC. Цей виріб також
відповідає Директиві про вміст небезпечних речовин 2011/65/EU.
Менеджер Євростандартів з Hitachi Koki Europe Ltd.
вповноважений заповнити таблицю технічних характеристик.
Ця декларація дійсна щодо вироба, маркованого СЕ.
Български Русский
Предмет на декларацията:
Hitachi Безжичен прободен трион
CJ14DSL, CJ18DSL
ЕО ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ
Ние декларираме на собствена отговорност, че продуктът
е в съответствие със стандартите или стандартизиращи
документи EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29,
EN55014-1, EN55014-2 и EN61000 съгласно Директиви 2004/108/
EО и 2006/42/EО. Този продукт съответства, също така, на
Директива RoHS 2011/65/EС.
Мениджърът Европейски стандарти в Hitachi Koki Europe Ltd. е
упълномощен за съставяне на техническото досие.
Тази декларация е приложима за продуктите с прикрепена
маркировка CE.
Предмет декларирования: Hitachi Аккумуляторный лобзик
CJ14DSL, CJ18DSL
ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ EC
Мы с полной ответственностью заявляем, что данное изделие
соответствует стандартам или документам стандартизации
EN60745-1, EN60745-2-11, EN60335-1, EN60335-2-29, EN55014-1,
EN55014-2 и EN61000 согласно Директивам 2004/108/EC
и 2006/42/EC. Данный продукт соответствует требованиям
Директивы 2011/65/EU по ограничению на использование
опасных веществ.
Менеджер отдела европейских стандартов качества компании
Hitachi Koki Europe Ltd. имеет право составлять технический
файл.
Данная декларация относится к изделиям, на которых имеется
маркировка CE.
Hitachi Koki Europe Ltd.
Clonshaugh Business & Technology Park, Dublin 17, lreland
28. 9. 2014
John de Loughry
European Standard Manager
28. 9. 2014
A. Yoshida
Vice-President & Director
Representative o ce in Europe
Hitachi Power Tools Europe GmbH
Siemensring 34, 47877 Willich 1, F. R. Germany
Head o ce in Japan
Hitachi Koki Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
409
Code No. C99710071 G
Printed in China
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200

Hitachi CJ 14DSL Operating instructions

Category
Power tools
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI