1/13
BF-24644 OXFORD HUTCH 56"W WITH 2 DRAWERS
ASSEMBLY INSTRUCTIONS
Made In China
BACK PANELS-2PCS
DRAWER
LARGE BACK PANEL-1PC
SHELVES-2PCS
SMALL STAND PANEL-1PC
J K
2/13
L
LEFT DRAWER
PANEL SIDES-2PCS
LEFT SIDE PANEL-1PC
RIGHT STAND PANEL-1PC
Follow instructions listed below in proper sequence as
PARTS LIST
LEFT STAND PANEL-1PC
BOTTOM PANELS-2PCS
RIGHT SIDE PANEL-1PC
G
H
TOP PANEL-1PC
D
A
E
B
I
C
F
material carefully for small parts,which may have came loose inside the
Department.For efficient and speedy service please indicate the
numbered to assure fast,easy and correct assembly.
missing or damaged,phone,fax,or mail to our Customer Service
compare with parts list to ensure all parts are present.If any parts are
carton during shipment. Count all parts and material hardware and
Thank you for purchasing this quality product.Be sure to check all packing
model number and code letter of part(s) needed
IMPORTANT NOTE:
SMALL
PANEL FRONTS-2PCS
CONNECTED
NOTE:THE SURFACE WITH THE STICKER IS THE BACK SIDE.
3/13
DOWELS-2PCS HARDWARES-2PCS
O
R
U
X
A1
DRAWER
KNOBS-2PCS
SCREWS-16PCS
Y
S
V
Z
CAM-TOOL-1PC
CAM-BOLTS-24PCS
T
W
SCREWS-18PCS
RIGHT DRAWER
P
M
DRAWER
Q
N
SCREWS-2PCS
SHELF SUPPORTS-8PCS
CAM-LOCKS-24PCS
ACROSS PANEL-1PC
PANEL SIDES-2PCS PANEL BACKS-2PCS
PANEL BOTTOMS-2PCS
EVA MATS-8PCS
THE ARROWS ON THE HIDDEN CAM-LOCKS SHOULD POINT TO THE CAM-BOLTS
NOTE:
4/13
UPON OPENING THOROUGHLY CLEAN ALL WOOD SURFACES TO REMOVE DUST
AND DIRT THAT MAY HAVE SETTLED ONTO FINISH DURING SHIPMENT.IN ORDER
TO PREVENT DAMAGE DURING ASSEMBLY,PLEASE ASSEMBLE THIS ITEM WITH AT
HOW TO USE THE CAM-TOOL
SHOULDER
ARROW
R
Q
LEAST TWO PEOPLE.
NOTE:
ARE TIGHT, THE SHOULDER SHOULD BE
AGAINST THE SURFACE OF THE PART.
ARROW
TURN THE CAM-BOLT SCREWS UNTIL THEY
NOTE:
X
L
P
S
K
M
V
B
PLACE CAM-BOLTS(Q)INTO HOLES IN PANEL(B)AND ATTACH USING 4 CAM-LOCKS(R).
ROTATE THE 4 CAM-BOLTS(Q)INTO HOLES IN RIGHT SIDE/STAND PANEL(D/F).
6/13
R
ROTATE THE 4 CAM-BOLTS(Q)INTO HOLES IN LEFT SIDE/STAND PANEL(C/E).
PLACE CAM-BOLTS(Q)INTO HOLES IN PANEL(B)AND ATTACH USING 4 CAM-LOCKS(R).
Q
F
D
R
Q
C
B
E
PLACE CAM-BOLTS(Q)INTO HOLES IN PANEL(G)AND ATTACH USING 2 CAM-LOCKS(R).
ROTATE THE 2 CAM-BOLTS(Q)INTO HOLES IN ACROSS PANEL(O).
PLACE CAM-BOLTS(Q)INTO HOLES IN PANEL(O)AND ATTACH USING 4 CAM-LOCKS(R).
O
7/13
Q
R
E
O
Q
G
F
R
ROTATE THE 4 CAM-BOLTS(Q)INTO HOLES IN STAND PANELS(E/F).
ROTATE THE 10 CAM-BOLTS(Q)INTO HOLES IN TOP PANEL(A).
8/13
C
E
F
G
D
R
A
Q
F
E
H
INSERT THE LARGE BACK PANEL(H)INTO SLOTS IN STAND PANELS(E/F).
PLACE CAM-BOLTS(Q)INTO HOLES IN PANELS(C/D/E/F/G)AND ATTACH USING 10 CAM-LOCKS(R).
J
PLACE THE SHELVES(J)ONTO THE SHELF SUPPORTS(U).
9/13
J
U
INSERT 8 SHELF SUPPORTS(U)INTO HOLES IN PANELS(C/D/E/F).
10/13
Y
ATTACH 2 SMALL BACK PANELS(I) USING 14 SCREWS(T).
T
I
I
T
Z
INSERT 2 DRAWERS TO THE SLIDERS.
INSERT 2 DOWELS(Z)INTO HOLES IN TOP PANEL(A).
ATTACH THE 8 EVA MATS(Y)TO BOTTOM PANEL(B).
11/13
T
(1)
A1
ATTACH 2 CONNECTED HARDWARES(A1) USING 4 SCREWS(T).
12/13
(2)
ATTACH 2 PLATES USING 4 SCREWS.
13/13
(1)
(2)
/
