Barbecook Cebu 3.1 Owner's manual

B

a

r

b

e

c

o

k

www.barbecook.com

Cebu 3.1

# 223.6831.000

Man_CEBU_3.1_131004_A.indd 1 7/10/13 09:46

2 www.barbecook.com

Man_CEBU_3.1_131004_A.indd 2 7/10/13 09:46

www.barbecook.com 3

NL

MONTAGE-INSTRUCTIES

Lees aandachtig de instructies alvorens de barbecue te monteren. Monteer de barbecue op een vlakke en propere ondergrond.

Opgelet: Wees voorzichtig tijdens het monteren van de barbecue. Het gereedschap kan het geëmailleerde oppervlak beschadigen. Het

kan gebeuren dat er vijzen over zijn na de montage.

FR

INSTRUCTIONS D’ASSEMBLAGE

Lisez attentivement les instructions avant d’assembler le barbecue. Assemblez le barbecue sur une surface plane et propre.

Attention: Soyez prudent au cours de l’assemblage du barbecue. Les outils peuvent endommager la surface émaillée. Il se peut qu’il

reste des fixations à la fin de l’assemblage.

EN

INSTALLATION INSTRUCTIONS

Carefully read the instructions before installing the barbecue. Install the barbecue on a flat and clean base.

Note: Be careful when installing the barbecue. Tools may damage the enamelled surface. Some screws may be left over after installation.

DE

MONTAGEANWEISUNGEN

Lesen Sie sich die Anweisungen vor der Montage des Grills sorgfältig durch. Montieren Sie den Grill auf einem ebenen und sauberen

Untergrund.

Achtung: Seien Sie vorsichtig, wenn Sie den Grill montieren. Die emaillierte Oberfläche des Grills kann durch das Werkzeug beschädigt

werden. Er kann sein, dass nach der Montage Schrauben übrig sind.

EL

ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ

Διαβάστε προσεχτικά τις οδηγίες πριν από την εγκατάσταση του μπάρμπεκιου. Εγκαταστήστε το μπάρμπεκιου σε επίπεδη και

καθαρή βάση.

Σημείωση: Να είστε προσεχτικοί κατά την εγκατάσταση του μπάρμπεκιου. Τα εργαλεία ενδέχεται να προκαλέσουν ζημιά στην

εμαγιέ επιφάνεια. Ενδέχεται να περισσέψουν κάποιες βίδες μετά την εγκατάσταση.

ES

INSTRUCCIONES DE INSTALACIÓN

Lea atentamente estas instrucciones antes de instalar la barbacoa. Instale la barbacoa sobre una base plana y limpia.

Nota: Tenga cuidado al instalar la barbacoa. Las herramientas pueden dañar la superficie esmaltada. Pueden sobrar algunos tornillos al

terminar la instalación.

BG

ИНСТРУКЦИИ ЗА ИНСТАЛИРАНЕ

Внимателно прочетете инструкциите, преди да инсталирате барбекюто. Инсталирайте барбекюто на равна и чиста повърх-

ност.

Забележка: Внимавайте, когато инсталирате барбекюто. Инструментите могат да повредят емайлираната повърхност.

Някои винтове могат да останат след инсталирането.

ET

PAIGALDUSJUHISED

Lugege hoolikalt juhiseid enne grilli paigaldamist. Asetage grill tasasele ja puhtale aluspinnale.

Märkus: Olge grilli paigaldades ettevaatlik. Tööriistad võivad selle emailitud pinda kahjustada. Mõned kruvid võivad pärast paigal-

damist üle jääda.

FI

ASENNUSOHJEET

Lue ohjeet huolellisesti ennen grillin asentamista. Asenna grilli tasaiselle ja puhtaalle alustalle.

Huomaa: Ole varovainen, kun asennat grilliä. Työkalut voivat vaurioittaa emaloitua pintaa. Asennuksesta voi jäädä ylimääräiseksi joita-

kin ruuveja.

NO

INSTRUKSER FOR MONTERING

Les instruksene nøye før montering av grillen. Monter grillen på en flat og ren base.

Merk: Utvis forsiktighet ved montering av grillen. Verktøy kan skade den emaljerte overflaten. Det kan bli skruer til overs etter monte-

ringen.

SV

INSTRUKTIONER FÖR INSTALLATION

Läs anvisningarna noga innan du installerar grillen. Installera grillen på ett platt och rent underlag.

Observera: Var försiktig när du installerar grillen. Verktygen kan skada den glaserade ytan. Vissa skruvar kan bli över efter installation.

Man_CEBU_3.1_131004_A.indd 3 7/10/13 09:46

Page is loading ...

www.barbecook.com 5

CEBU 3.1

# 223.6831.000

58

59

800

700

600

500

400

300

200

100

09

40

57

56

55

52

02

50

43

44

25

02

04

03

01

03

04

06

08

12

08

22

24

17

13

12

14

51

16

23

24

23

24

23

26

07

31

39

29

33

36

28

45

27

38

37

46

48

30

34

35

41

24

42

47

32

11

10

05

53

54

56

Man_CEBU_3.1_131004_A.indd 5 7/10/13 09:46

6 www.barbecook.com

CEBU 3.1

#223.6831.000

1 2276831010 33 2276831330

2 2276831020 34 2276831340

3 2276831030 35 2276831350

4 2276831040 36 2276831360

5 2276831050 37 2276831370

6 2276831060 38 2276831380

7 2276831070 39 2276831390

8 2276831080 40 2276831400

9 2276831090 41 2276831410

10 2276831100 42 2276831420

11 2276831110 43 2276831430

12 2276831120 44 2276831440

13 2276831130 45 2276831450

14 2276831140 46 2276831460

15 2276831150 47 2276831470

17 2276831170 48 2276831480

22 2276831220 50 2276831500

23 2276831230 51 2276831510

24 2276831240 52 2276831520

25 2276831250 53 2276831530

26 2276831260 54 2276831540

27 2276831270 55 2276831550

28 2276831280 56 2276831560

29 2276831290 57 2276831570

30 2276831300 58 2279900210

31 2276831310 59 2279900230

32 2276831320

Man_CEBU_3.1_131004_A.indd 6 7/10/13 09:46

www.barbecook.com 7

1

2

Man_CEBU_3.1_131004_A.indd 7 7/10/13 09:46

8 www.barbecook.com

3

4 5

Man_CEBU_3.1_131004_A.indd 8 7/10/13 09:46

www.barbecook.com 9

80 0

70 0

600

500400300

20 0

100

6 7

8 9

Man_CEBU_3.1_131004_A.indd 9 7/10/13 09:46

10 www.barbecook.com

10 11

12

Man_CEBU_3.1_131004_A.indd 10 7/10/13 09:46

www.barbecook.com 11

800

700

600

500

400

300

200

100

13 14

15

100

200

300

400

500

600

700

800

3mm

Man_CEBU_3.1_131004_A.indd 11 7/10/13 09:47

12 www.barbecook.com

10 0

200

30 0 400

500

60 0

700

80 0

AA - 1,5 Volt

+ -

16 17

18

Man_CEBU_3.1_131004_A.indd 12 7/10/13 09:47

www.barbecook.com 13

Man_CEBU_3.1_131004_A.indd 13 7/10/13 09:47

14 www.barbecook.com

connection for FRANCE

We recommend:

PROPANE

HOSE CONNECTION

A

1

2

3

4

Man_CEBU_3.1_131004_A.indd 14 7/10/13 09:47

Page is loading ...

16 www.barbecook.com

2. VERY IMPORTANT

Then tighten the connector firmly using

two spanners. Use a 22 mm AF spanner

to tighten the connector while holding

the gas distribution pipe in place with a

16 mm AF spanner.

3. Slide the hose from the regulator over

connector A.

4. Tighten the span ring level with connec

-

tor A. Make sure that the gas hose is

connected tightly to the connector.

B – French connector

FR

1. Fit the supplied connector to the appli-

ance. Tighten first by hand.

2. VERY IMPORTANT

Then tighten the connector firmly using

two spanners. Use a 22 mm AF spanner

to tighten the connector while holding

the gas distribution pipe in place with a

16 mm AF spanner.

3. Tighten the gas hose onto the just-fitted

connector B. Tighten first by hand.

4. VERY IMPORTANT

Then tighten the connector firmly using

two spanners. Use an adjustable span-

ner to tighten the gas hose while holding

the connector in place with a 16 mm AF

spanner.

We recommend connecting the appli-

ance to Propane for the best results.

DE

WICHTIG!

Montieren Sie den rechten Anschluss!

Die Verpackung enthält zwei Anschlüsse.

A – Standardanschluss

BE – CH – CZ – DK – ES – FI – GB – IE –

IT – PT – SI

1. Den mitgelieferten Anschluss am Gerät

anbringen. Zuerst handfest anziehen.

2. SEHR WICHTIG

Anschließend den Anschluss mit zwei

Schraubenschlüssel fest anziehen. Einen

22 mm AF-Schlüssel zum Festziehen

des Anschlusses verwenden. Dabei das

Gasverteilerrohr mit einem 16 mm AF-

Schlüssel gegenhalten.

3. Verlegen Sie den Schlauch vom Regler

zum Anschluss A.

4. Den Überwurf ohne Verkanten an An

-

schluss A festziehen.Darauf achten, dass

der Gasschlauch fest mit dem Anschluss

verbunden ist.

B – Anschluss Frankreich

FR

1. Den mitgelieferten Anschluss am Gerät

anbringen. Zuerst handfest anziehen.

2. SEHR WICHTIG

Anschließend den Anschluss mit zwei

Schraubenschlüssel fest anziehen. Einen

22 mm AF-Schlüssel zum Festziehen

des Anschlusses verwenden. Dabei das

Gasverteilerrohr mit einem 16 mm AF-

Schlüssel gegenhalten.

3. Den Gasschlauch an dem soeben

montierten Anschluss B festschrauben.

Zuerst handfest anziehen.

4. SEHR WICHTIG

Anschließend den Anschluss mit zwei

Schraubenschlüsseln fest anziehen.

Einen verstellbaren Schraubenschlüssel

zum Festziehen des Gasschlauchs ver-

wenden. Dabei den Anschluss mit einem

16 mm AF-Schlüssel gegenhalten.

Für ein optimales Ergebnis empfehlen

wir den Betrieb des Geräts mit Propan-

gas.

EL

ΣΗΜΑΝΤΙΚΟ!

Τοποθετήστε τον σωστό σύνδεσμο!

Στο κουτί περιλαμβάνονται δύο σύνδεσμοι.

A – Τυπικός σύνδεσμος

BE – CH – CZ – DK – ES – FI – GB – IE –

IT – PT – SI

1. Συναρμολογήστε τον παρεχόμενο

σύνδεσμο στη συσκευή. Αρχικά, σφίξτε

τον με το χέρι.

2. ΠΟΛΥ ΣΗΜΑΝΤΙΚΟ

Στη συνέχεια, σφίξτε καλά το σύνδεσμο

χρησιμοποιώντας δύο κλειδιά σύσφιγξης.

Χρησιμοποιήστε ένα κλειδί 22 mm AF για

να σφίξετε το σύνδεσμο, ενώ κρατάτε το

σωλήνα διανομής αερίου στη θέση του

με ένα κλειδί 16 mm AF.

3. Περάστε τον εύκαμπτο σωλήνα από το

ρυθμιστή στο σύνδεσμο A.

4. Σφίξτε τον συνδετικό δακτύλιο

ευθυγραμμισμένα με το σύνδεσμο A.

Βεβαιωθείτε ότι ο εύκαμπτος σωλήνας

αερίου είναι σταθερά συνδεδεμένος στο

σύνδεσμο.

B – Γαλλικός σύνδεσμος

FR

1. Συναρμολογήστε τον παρεχόμενο

σύνδεσμο στη συσκευή. Αρχικά, σφίξτε

τον με το χέρι.

2. ΠΟΛΥ ΣΗΜΑΝΤΙΚΟ

Στη συνέχεια, σφίξτε καλά το σύνδεσμο

χρησιμοποιώντας δύο κλειδιά σύσφιγξης.

Χρησιμοποιήστε ένα κλειδί 22 mm AF για

να σφίξετε το σύνδεσμο, ενώ κρατάτε το

σωλήνα διανομής αερίου στη θέση του

με ένα κλειδί 16 mm AF.

3. Σφίξτε τον εύκαμπτο σωλήνα αερίου στο

σύνδεσμο B που μόλις τοποθετήσατε.

Αρχικά σφίξτε τον με το χέρι.

4. ΠΟΛΥ ΣΗΜΑΝΤΙΚΟ

Στη συνέχεια, σφίξτε καλά το σύνδεσμο

χρησιμοποιώντας δύο κλειδιά σύσφιγξης.

Χρησιμοποιήστε ένα ρυθμιζόμενο κλειδί

για να σφίξετε τον εύκαμπτο σωλήνα

αερίου, ενώ κρατάτε το σύνδεσμο στη

θέση του με ένα κλειδί 16 mm AF.

Για βέλτιστα αποτελέσματα, συνιστάται

η σύνδεση της συσκευής σε προπάνιο.

ES

¡IMPORTANTE!

Ajuste el conector correcto.

Con el aparato se suministran dos conec-

tores.

A – conector convencional

BE – CH – CZ – DK – ES – FI – GB – IE –

IT – PT – SI

1. Ajuste el conector suministrado al

aparato apretándolo primero a mano.

2. MUY IMPORTANTE

Después, apriete bien el conector con

dos llaves de tuercas. Utilice una llave

de tuercas de 22 mm entre caras para

apretar el conector mientras mantiene la

tubería de distribución de gas en su sitio

con una llave de tuerca de 16 mm entre

caras.

3. Deslice el tubo flexible del regulador

sobre el conector A.

4. Apriete el anillo de separación de modo

que quede al nivel del conector A.

Asegúrese de que el tubo flexible de gas

esté firmemente conectado al conector.

B – Conector francés

FR

1. Ajuste el conector suministrado al

aparato apretándolo primero a mano.

2. MUY IMPORTANTE

Después, apriete bien el conector con

dos llaves de tuercas. Utilice una llave

de tuercas de 22 mm entre caras para

apretar el conector mientras mantiene la

tubería de distribución de gas en su sitio

con una llave de tuerca de 16 mm entre

caras.

3. Apriete, primero a mano, el tubo flex

-

ible de gas al conector B que acaba de

ajustar.

4. MUY IMPORTANTE

Después, apriete bien el conector con

dos llaves de tuercas. Utilice una llave

de tuercas ajustable para apretar el

tubo flexible de gas mientras mantiene

el conector en su sitio con una llave de

tuercas de 16 mm entre caras.

Man_CEBU_3.1_131004_A.indd 16 7/10/13 09:47

Page is loading ...

22 www.barbecook.com

NL

Markering van de inspuiters

• Inspuiter hoofdbranders: 0,98

• Inspuiter zijbrander: 0,92

FR

Marquage des injecteurs

• Injecteur des brûleurs principaux: 0,98

• Injecteur du brûleur latéral: 0,92

EN

Marking of the injectors

• Injector main burners: 0,98

• Injector side burner: 0,92

DE

Markierung der Einspritzdüsen

• Einspritzdüse Hauptbrenner: 0,98

• Einspritzdüse Seitenbrenner: 0,92

EL

Σημάδεμα εγχυτήρων

• Κύριοι καυστήρες εγχυτήρα: 0,98

• Πλάγιος καυστήρας εγχυτήρα: 0,92

ES

Marcado de los inyectores

• Quemadores principales del inyector:

0,98

• Quemador lateral del inyector: 0,92

BG

Маркиране на инжекторите

• Инжектор главна горелка: 0,98

• Инжектор странична горелка: 0,92

ET

Pihustite märgistamine

•

Peapőletite pihusti:

0,98

•

Külgpőleti pihusti:

0,92

FI

Injektorien merkinnät

• Injektoripääpolttimet: 0,98

• Injektorisivupoltin: 0,92

NO

Markering av injektorene

• Injektor hovedbrennere: 0,98

• Injektor sidebrenner: 0,92

SV

Markering av injektorerna

• Injektor till huvudbrännarna: 0,98

• Injektor till sidobrännare: 0,92

IT

Indicazioni relative agli iniettori

• Iniettore bruciatori principali: 0,98

• Iniettore bruciatore laterale: 0,92

PT

Marcas dos injectores

• Bicos de gás principais do injector:

0,98

• Bico de gás lateral do injector: 0,92

DA

Markering af dyser

• Dyse hovedbrænder: 0,98

• Dyse sidebrænder: 0,92

HU

A befecskendezők megjelölése

• A központi égőfejek

befecskendezője: 0,98

• Az oldalsó égőfej

befecskendezője: 0,92

RO

Marcarea injectoarelor

• Injector arzătoare principale: 0,98

• Injector arzător lateral: 0,92

CS

Označení trysek

• Tryska hlavních hořáků: 0,98

• Tryska bočního hořáku: 0,92

HR

Oznake na brizgalicama

• Brizgalica glavnog plamenika: 0,98

• Brizgalica bočnog plamenika: 0,92

LT

Purkštuvų žymėjimas

• Pagrindinių degiklių purkštuvas: 0,98

• Šoninio degiklio purkštuvas: 0,92

LV

Iesmidzināšanas apzīmējumi

• Iesmidzināšanas galvenie degļi: 0,98

• Iesmidzināšanas sānu degļi: 0,92

PL

Oznaczenia wtryskiwaczy

• Wtryskiwacz palników głównych: 0,98

• Wtryskiwacz palnika bocznego : 0,92

SK

Označenie trysiek

• Tryska hlavných horákov: 0,98

• Tryska bočných horákov: 0,92

SL

Označevanje injektorjev

• Glavni gorilniki injektorja: 0,98

• Stranski gorilnik injektorja: 0,92

Man_CEBU_3.1_131004_A.indd 22 7/10/13 09:47

Page is loading ...

24 www.barbecook.com

NL

HANDLEIDING VOOR MONTAGE, GEBRUIK EN ONDERHOUD 25

FR

NOTICE DE MONTAGE, D’UTILISATION ET D’ENTRETIEN 31

EN

INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS 38

DE

ANLEITUNG ZU MONTAGE, GEBRAUCH UND PFLEGE 44

EL

ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ, ΧΡΗΣΗΣ ΚΑΙ ΣΥΝΤΗΡΗΣΗΣ 51

ES

INSTRUCCIONES DE INSTALACIÓN, USO Y MANTENIMIENTO 58

BG

ИНСТРУКЦИИ ЗА МОНТАЖ, УПОТРЕБА И ПОДДРЪЖКА 65

ET

PAIGALDUS-, KASUTUS- JA HOOLDUSJUHISED 72

FI

ASENNUS-, KÄYTTÖ- JA HUOLTO-OHJEET 78

NO

INSTRUKSER FOR INSTALLASJON, BRUK OG VEDLIKEHOLD 84

SV

INSTRUKTIONER FÖR INSTALLATION, ANVÄNDNING OCH UNDERHÅLL 90

IT

ISTRUZIONI DI INSTALLAZIONE, USO E MANUTENZIONE 96

PT

INSTRUÇÕES DE INSTALAÇÃO, UTILIZAÇÃO E MANUTENÇÃO 103

DA

INSTRUKTIONER OM INSTALLATION, BRUG OG VEDLIGEHOLDELSE 110

HU

ÜZEMBEHELYEZÉSI, HASZNÁLATI ÉS KARBANTARTÁSI ÚTMUTATÓ 116

RO

INSTRUCŢIUNI DE INSTALARE, UTILIZARE ŞI ÎNTREŢINERE 122

CS

NÁVOD K INSTALACI, POUŽÍVÁNÍ A ÚDRŽBĚ 129

HR

UPUTE ZA UGRADNJU, UPORABU I ODRŽAVANJE 135

LT

MONTAVIMO, NAUDOJIMO IR PRIEŽIŪROS NURODYMAI 141

LV

UZSTĀDĪŠANAS, LIETOŠANAS UN APKOPES INSTRUKCIJA 147

PL

WSKAZÓWKI DOTYCZĄCE MONTAŻU, UŻYTKOWANIA I KONSERWACJI 153

SK

POKYNY K MONTÁŽI, POUŽÍVANIU A ÚDRŽBE 159

SL

NAVODILA ZA NAMESTITEV, UPORABO IN VZDRŽEVANJE 165

Man_CEBU_3.1_131004_A.indd 24 7/10/13 09:47

Page is loading ...

38 www.barbecook.com

EN

INSTALLATION, USE AND MAINTE-

NANCE INSTRUCTIONS

SAFETY INFORMATION

THIS APPLIANCE IS DESIGNED FOR

OUTDOOR USE ONLY

IF YOU SMELL GAS:

1. TURN OFF THE GAS SUPPLY

2. EXTINGUISH ANY OPEN FLAME

3. OPEN THE LID

4. IF ODOUR CONTINUES, IMMEDIA

-

TELY CALL YOUR GAS SUPPLIER

OR THE FIRE DEPARTMENT

• THE USER IS RESPONSIBLE FOR

PROPER INSTALLATION AND APPRO-

PRIATE USE OF THE BARBECUE.

• FAILURE TO COMPLY WITH THE

INSTRUCTIONS IN THIS MANUAL MAY

RESULT IN A DANGEROUS FIRE OR

EXPLOSION.

• FAILURE TO FOLLOW THE INSTRUC-

TIONS IN THIS MANUAL MAY RESULT

IN SERIOUS INJURIES AND MATERIAL

DAMAGE.

• USE PROTECTIVE GLOVES WHEN

HANDLING PARTICULARLY HOT PARTS

• MODIFICATIONS TO THE BARBECUE

ARE DANGEROUS AND NOT PERMIT-

TED. THIS APPLIANCE MUST BE IN-

STALLED IN ACCORDANCE WITH THE

APPLICABLE PROVISIONS.

• STORE THE CYLINDER OUTDOORS IN

A WELL-VENTILATED AREA

• NEVER PLACE THE SPARE CYLINDER

(FULL OR EMPTY) UNDER OR NEXT TO

A BARBECUE IN USE.

• NEVER STORE OR USE GASOLINE OR

OTHER FLAMMABLE VAPOURS AND

LIQUIDS IN THE VICINITY OF THIS OR

ANY OTHER BARBECUE.

• KEEP COMBUSTIBLE MATERIAL AT

LEAST 76 CM AWAY FROM THE BAR-

BECUE

• KEEP THE AREA AROUND YOUR BAR-

BECUE AT ALL TIMES FREE FROM ANY

COMBUSTIBLE MATERIALS, GASOLINE

OR OTHER FLAMMABLE LIQUIDS

• USE THE BARBECUE ONLY OUT-

DOORS IN A WELL-VENTILATED AREA

AND AT LEAST 3 M FROM ANY DWEL-

LING OR BUILDING.

• DO NOT USE THIS APPLIANCE UNDER

AN OVERHANGING STRUCTURE OR

FOLIAGE

• DO NOT USE THE BARBECUE ON

A BOAT OR OTHER RECREATIONAL

VEHICLE

• DO NOT USE THE BARBECUE IN A GA-

RAGE, SHED, CORRIDORS OR OTHER

ENCLOSED AREAS

• NEVER LEAVE THE BARBECUE UNAT-

TENDED WHEN IN USE

• DO NOT OBSTRUCT THE FLOW OF

COMBUSTION AND VENTILATION AIR

TO THE BARBECUE

• DO NOT USE THE BARBECUE WHEN

YOU HAVE CONSUMED ALCOHOL OR

TAKEN DRUGS

• ACCESSIBLE PARTS MAY BECOME

VERY HOT. KEEP (YOUNG) CHILDREN

AND ANIMALS AWAY FROM THE BAR-

BECUE.

• DO NOT MOVE THE BARBECUE WHEN

IN USE

• NEVER USE CHARCOAL, WOOD OR

BRIQUETTES

• NEVER USE LAVA ROCKS OR CERA

-

MIC BRIQUETTES

• KEEP THE VENT HOLES IN THE TROL-

LEY CLEAR AT ALL TIMES.

• PARTS SEALED BY THE MANUFACTU-

RER OR HIS REPRESENTATIVE MAY

NOT BE ALTERED BY THE USER.

• NEVER LIGHT THE SIDE BURNER WIT-

HOUT OPENING THE LID.

• ALWAYS PLACE THE TWO ROUND

OPENINGS IN THE GRID ABOVE THE

AROMAZ® TRAYS.

• ALWAYS PLACE THE BARBECUE ON

FIRM GROUND AWAY FROM OBJECTS

THAT MAY CATCH FIRE OR MELT.

GAS CONNECTION

GAS CYLINDER

Always use an approved cylinder that

complies with all national provisions and

standards.

• We recommend this product is con

-

nected to PROPANE

• Always keep the cylinder in a stable

and upright position.

• Be careful when handling the cylin-

der valves

• Never connect a cylinder without

regulator to the barbecue.

• Never connect a non-regulated

cylinder to the barbecue.

• Always close the cylinder valves

when the barbecue is not in use

• Never place the spare cylinder under

or next to a barbecue in use

• Never expose the cylinder to exces-

sive heat or direct sunlight

• Change the flexible tube if required

by national regulations

HOSE AND REGULATOR

The hose and regulator are not supplied

by the manufacturer. You may only use

a combination of hose and regulator if

this complies with all local and national

standards and rules and corresponds with

the connections on the gas cylinder used

and the gas type/nominal pressure given

on the barbecue. Keep the hose as short

as possible.

• Never connect the barbecue to a

non-regulated gas supply. Never try

to alter the hose or regulator in any

way whatsoever.

• Prior to each use of the barbecue,

check the hose over its full length

for any damage (cracks, tears, burnt

sections) or excessive wear. When

you notice any damage or wear,

replace the hose before using the

barbecue, in accordance with the

national standards

• Fat (or any other hot substance)

must never fall onto the hose, and

the hose must never come into

contact with any hot points on the

barbecue

• The connector of the regulator must

be protected when it is not connec-

ted to the cylinder

• Ensure that the hose does not drag

on the ground, because this can

cause problems for the airtightness

of the connection.

• Do not distort the hose when con-

necting or disconnecting the cylin-

der

• The maximum permissible length of

the hose is 1.5 m

CONNECTING THE GAS CYLINDER

On some gas pressure regulators you must

press ON to connect and OFF to discon

-

nect; other regulators have a nut and a

left-handed screw thread to connect the

regulator to the gas cylinder. Follow the

instructions for the gas pressure regulator

in question.

1. Connect the hose to the gas regulator.

a. Push the hose over the regulator

and tighten up the span ring.

b. Wind the gas hose over the regula-

tor, first by hand and then fasten it

firmly using an adjustable spanner.

Man_CEBU_3.1_131004_A.indd 38 7/10/13 09:47

www.barbecook.com 39

2. Connect the gas regulator to the cylin-

der.

a. Screw the gas pressure regulator

connector to the right on the tank

b. Screw the gas pressure regulator

connector to the left on the tank.

TEST FOR LEAKS

Perform a leak test:

• Before lighting the appliance for the

first time

• Whenever the gas cylinder is chan

-

ged or a gas component is replaced.

• At least once a year, preferably at

the beginning of the season

The leak test must be carried out outdoors,

in a well-ventilated area nowhere close to

naked flames, heat sources or sparks. Do

not smoke! Use a 50/50 mixture of liquid

soap and water or leak spray for the test.

WARNING

Do not look for gas leaks with a lighter or

match! Ensure that there are no sparks

or naked flames in the vicinity when you

check for leaks. Sparks or naked flames

can cause a fire or explosion resulting in

serious or fatal injuries and damage to

property.

All the parts which are connected in the

factory are carefully checked for gas leaks.

The burners have been tested. However,

as a safety measure you must check all the

connections for leaks before use.

Do not light the burners when checking for

leaks.

Method:

• Prepare some soapy water

• Once the full gas cylinder has been

connected to the appliance and

all the control knobs are turned to

‘OFF’, slowly open the gas cylinder

one turn by turning to the right

• Check for leaks by applying soapy

water to the connections. Sealing

should be checked in the following

places:

1. The welds on the cylinder

2. The connection with the appliance

3. The connection between the hose and

the cylinder + The connection between

the regulator and the cylinder

4. The gas hose between the appliance

and the cylinder

• Check that no soap bubbles appear.

If you can see soap bubbles, and

the soap bubbles are growing larger,

there is a gas leak.

NOK OK

If there is a leak, turn off the gas and

tighten the connection. Open the gas

valve and check the connection again with

the soapy water. If the leak has not been

repaired, contact a distributor in your area.

DO NOT USE THE APPLIANCE. You can

find a list of distributors on our web site.

Log in on www.barbecook.com

Man_CEBU_3.1_131004_A.indd 39 7/10/13 09:47

40 www.barbecook.com

• Once you have checked for leaks,

turn off the gas, rinse the connec-

tions with water and dry to prevent

the formation of rust.

• Turn the cylinder knob to the left to

close the cylinder.

Note: the regulator may be different

from the one illustrated here.

WARNING: You must carry out these

leak tests even if your appliance is set

up by the dealer or the shop.

REPLACING THE CYLINDER

When changing the gas cylinder, ensure

that the knobs on the barbecue are in the

OFF position and that the gas cylinder is

closed. Do not replace the gas cylinder

close to anything that may produce a

flame or spark.

TRANSPORT AND STORAGE OF THE

GAS CYLINDER

Although perfectly safe when handled

correctly, lack of caution may result in fire

and/or explosion.

To minimise the risks:

• Never store the cylinder in a buil

-

ding, garage or other enclosed area,

but always in a well-ventilated area

• Never store the cylinder in the

vicinity of another gas operated ap-

pliance, or in a very warm area, such

as a car or boat

• Always keep the cylinder out of

reach for children

• Always transport and store the cylin-

der in an upright position

• Do not smoke near the gas cylinder.

USE

PRIOR TO FIRST USE / AFTER

PROLONGED PERIOD OF NON-USE

Do not use the barbecue before you have

read, understood and checked all informa

-

tion in this manual.

Ensure that:

• The barbecue is correctly installed

• There is no leak in the gas supply

(see ‘Leakage test’)

• The burners are correctly installed,

the venturi tubes are properly placed

over the openings of the gas valves

(Fig. D), and there are no obstruc-

tions (see safety information and

cleaning of the burners)

• None of the gas supply hoses can

come into contact with a hot surface

• Your barbecue is installed in a safe

place

D

LIGHTING THE BURNERS

Prior to lighting the burners, all checks and

procedures detailed in the chapter ‘Before

the first use’ must have been carried out.

• The lid of the barbecue must always

be open when you light the burner(s)

• Do not bend directly over the barbe

-

cue when lighting the burner(s)

• The control knobs of the barbecue

must be ‘OFF’. Slowly open the gas

cylinder valve. Before opening the

control knob of one burner, wait ap-

prox. 10 seconds to allow to gas to

stabilize

• Important: first light the middle bur-

ner

• As soon as one burner has been

lighted, you only need to put the

control knob of the other burner(s) in

the position ‘HIGH’ to light them.

• Never try to light all burners at once

HIGH

LOW

LIGHTING THE BURNERS WITH THE

IGNITER

The battery is not supplied as standard.

• Open the lid of the barbecue

• Open the gas cylinder valve.

• Press the igniter until you hear

sparks

• Holding down the igniter, press the

control knob of the middle burner

and turn to ‘HIGH’

• If the burner does not light after 3

attempts, disconnect the gas and

wait 5 minutes before trying again.

This will allow the accumulated gas

to escape. Try again, repeating the

above steps.

• If the burner still does not light, read

the chapter ‘Troubleshooting Guide’

to determine the cause and the re-

medy, or use a match as described

below.

LIGHTING THE BURNERS WITH A

MATCH

Left and right at the bottom of the burner

box is a small opening that can be used to

light the burners with a match, if the elec

-

tronic igniter does not work. (Fig. G)

• Open the lid of the barbecue

• Place a match in the match holder

provided (Fig. G)

• Hold a burning match through the

hole, approx. 13 mm from the burner

• Open the gas cylinder valve.

• Push the required control knob and

turn to ‘HIGH’. The burner should

light within 5 seconds. If not, turn

the control knob off and wait 5

minutes to allow the gas to escape.

• Repeat steps 1 through 5. If the

burner still does not light after 3

attempts, read the chapter ‘Trouble

-

shooting Guide’

G

LIGHTING THE OTHER BURNERS

• As soon as the first burner has been

lighted, you only need to put the

control knob of the other burner(s) in

the position ‘HIGH’ to light them.

LIGHTING THE SIDE BURNER USING

THE IGNITER

First open the lid of the side burner.

To light the side burner, use the igniter on

the control panel and the control knob on

the side table.

• Press the igniter until you hear

sparks.

• Holding down the igniter, press the

control knob of the side burner and

turn to ‘HIGH’

• Repeat a number of times if the

burner does not light immediately.

• If the burner does not light after

5 seconds, turn the control knob to

‘OFF’ and wait 5 minutes to allow

the gas to escape.

Man_CEBU_3.1_131004_A.indd 40 7/10/13 09:47

www.barbecook.com 41

• Repeat steps 1 through 3. If the

burner still does not light, read the

chapter ‘Troubleshooting Guide’ or

use a match as described below.

Note:

• the maximum load of the side bur-

ner is 9 kg!

• the maximum diameter of the coo-

king vessel is 220 mm

LIGHTING THE SIDE BURNER WITH A

MATCH

• Place a match in the match holder

provided

• Hold a burning match approx.

13 mm from the burner (Fig. H)

• Push the control knob of the side

burner and turn to ‘HIGH’. The bur-

ner should light within 5 seconds. If

not, turn the control knob ‘OFF’ and

wait 5 minutes to allow the gas to

escape.

• Repeat steps 1 through 3. If the

burner still does not light, read the

chapter ‘Troubleshooting Guide’

to determine the cause and the

remedy.

H

VISUAL CHECK OF THE FLAMES

If the flames of the burners jump out of the

burner box when the barbecue is in use,

immediately turn off the control knobs.

Wait 5 minutes to allow the gas to escape

before relighting the barbecue. Read the

chapter ‘troubleshooting guide’ if the pro

-

blem persists.

Each time you light the barbecue you

should check the flames. (Fig. I) a proper

flame is almost comletely blue, with some

yellow at the top. If the flame is abnormally

small and for the most part yellow, switch

off the barbecue and check the venturi

tubes for obstructions, or read the chapter

‘troubleshooting guide’.

I

SWITCHING OFF THE BARBECUE

• Close the gas cylinder valve

• Turn all control knobs of the burners

to ‘OFF’.

If you follow the above order, there will be

no more pressurized gas in the system.

USEFUL TIPS FOR USE OF THE

BARBECUE

USING YOUR BRAHMA FOR THE FIRST

TIME

When using your gas barbecue for the

first time, you must first allow the unit to

run in by operating it for a short period

of time without any food. To run in the

barbecue, light the barbecue. Close the lid

and maintain the temperature at ‘HIGH’

for 15 minutes. Do not open the lid during

this procedure. You then open the lid and

allow the barbecue to operate for another

5 minutes at ‘HIGH’. The barbecue is now

ready for use.

WARMING UP THE BARBECUE

Allow the barbecue to warm up before pla

-

cing any food on it. Close the lid and heat

the cooking surface for at least 10 minutes

in the setting ‘HIGH’. To bake at a lower

temperature than the setting ‘HIGH’, turn

the control knobs to the required position

before placing any food on the barbecue.

COOKING TIME

The actual cooking time depends on vari

-

ous factors such as taste, outside tempe-

rature and wind. Experience will teach you

how to estimate this time.

KEEPING FLARE-UPS UNDER CONTROL

During barbecuing, some flare-ups are

natural. Too many flare-ups, however, will

increase the temperature in the barbecue,

thereby causing accumulated fat to ignite

and cause fire.

To reduce flare-ups:

• Remove excess fat from the meat

before baking

• Bake fat meat at a low setting

• Check that the hole in front of the fat

drain is not blocked and the fat drip

cup is not full

• Bake with closed lid to cut off the air

supply and lower the heat settings

NOTE: If the lid is closed, your barbecue

will retain a more constant temperature

and food can be baked faster and with less

energy.

Should the burner(s) go out during baking,

open the lid, turn off the burner(s) and

wait 5 minutes to allow the gas to escape

before relighting the burner.

HOW TO PREVENT FOOD FROM

STICKING TO THE GRID

• Rub food lightly with oil before you

place it on the grid

• Or brush the grid with some cooking

oil to prevent food from sticking

• Do not turn food too quickly after

placing it on the grid

WARNING:

• Never leave your barbecue unat

-

tended when in use, especially in

the presence of children or domestic

animals. Regularly check the barbe

-

cue for proper functioning of all its

components

• Accessible parts can become very

hot. Use appropriate protection

when you touch these parts. Keep

young children away from the appli

-

ance.

• Never move the barbecue when in

use

• Never use charcoal, wood or bri-

quettes

• Never use lava rocks or ceramic

briquettes

TIPS FOR CLEANING AND

MAINTENANCE

To prolong the life of your appliance, it

should be cleaned carefully after every

use.

BURNING OFF RESIDUES

After use, you can let your appliance

burn, empty of food and with the cover

closed, for a further ten minutes with all

the burners turned to HIGH. This ensures

that a large proportion of any residues will

be burnt off, making subsequent cleaning

easier. Let the appliance cool down.

You can then remove the burnt residues

with a non-abrasive brush and clean.

GRILLS AND GRIDDLES

After every use, let the barbecue cool

down and clean the grills with a non-abra

-

sive brush. Grills can also be washed with

the special ‘Barbecook® all cleaner’, a soft

detergent or sodium bicarbonate. Do not

use oven cleaners.

To prolong the life of your appliance, you

should carry out all the activities listed be

-

low, preferably at the start of the barbecue

season.

BURNERS AND VENTURI TUBES

IMPORTANT

Natural hazards - spiders and insects:

very small insects might make a web

or nest in the venturi tubes of the gas

burners (fig. E).

Man_CEBU_3.1_131004_A.indd 41 7/10/13 09:47

Page is loading ...

Barbecook Cebu 3.1 Owner's manual

Related papers

Other documents