Subaru 2015 Forester Owner's manual

Category
Cars
Type
Owner's manual

This manual is also suitable for

Foreword
Congratulations on choosing a SUBARU vehicle equipped with EyeSight
TM
.
EyeSight incorporates the latest driver assistance features available from
SUBARU, including such features as Adaptive Cruise Control, a Lead Vehicle Start
Alert and a Lane Departure and Lane Sway Warning, all of which are designed to
assist the driver in making decisions and increase driver comfort and
convenience. Initially, the operation and use of the various EyeSight features may
be unfamiliar to you. That is why we urge you to read this manual carefully before
using EyeSight. We also recommend that you first take the time to test EyeSight in
order to experience its features for yourself so that you can become familiar with
their operation.
Please keep in mind that it is the responsibility of drivers to operate their vehicles
safely at all times. Drivers should always remain alert and should never become
complacent while operating their vehicles because of the presence of EyeSight.
EyeSight is never a substitute for active driver involvement and it may not operate
optimally under all driving conditions.
This booklet is a supplement to the Owner’s Manual for your SUBARU vehicle and
contains a detailed description of EyeSight. It should be read in conjunction with
your Owner’s Manual so that you will gain a thorough understanding of the proper
operation of your vehicle.
The information, specifications and illustrations found in this booklet are those in
effect at the time of printing. FUJI HEAVY INDUSTRIES LTD. reserves the right to
change specifications and designs at any time without prior notice and without
incurring any obligation to make the same or similar changes on vehicles
previously sold.
Please keep this booklet together with your Owner’s Manual and leave it in the
vehicle at the time of resale. The next owner will need the information it contains.
FUJI HEAVY INDUSTRIES LTD., TOKYO, JAPAN
is a registered trademark of FUJI HEAVY INDUSTRIES LTD.
© Copyright 2015 FUJI HEAVY INDUSTRIES LTD.
2.fm 1 ページ 2015年3月30日 月曜日 午後4時17分
3
1
2
4
5
6
7
8
EyeSight
About EyeSight•••••••••••••••••••••••••••••••••••••••••••••••••••••2
Adaptive Cruise Control •••••••••••••••••••••••••••••••••••••••• 21
Pre-Collision Braking System ••••••••••••••••••••••••••••••••• 43
Pre-Collision Throttle Management •••••••••••••••••••••••••• 52
Lane Departure Warning •••••••••••••••••••••••••••••••••••••• 58
Lane Sway Warning ••••••••••••••••••••••••••••••••••••••••••••• 61
Lead Vehicle Start Alert ••••••••••••••••••••••••••••••••••••••• 64
Conventional Cruise Control••••••••••••••••••••••••••••••••••• 65
List of buzzer sounds •••••••••••••••••••••••••••••••••••••••••• 75
EyeSight malfunction and temporary stop •••••••••••••••••• 76
Customizing functions••••••••••••••••••••••••••••••••••••••••••• 79
List of the pop-up screens on the multi function display ••• 81
Troubleshooting •••••••••••••••••••••••••••••••••••••••••••••••••• 84
B8192BE-C.book 1 ページ 2014年9月16日 火曜日 午後2時25分
2
About EyeSight
EyeSight is a driving support system that uses a range of functions to assist the driver in
making decisions in order to provide for more safe and comfortable driving and to reduce
driver fatigue. EyeSight makes use of original stereo cameras designed by SUBARU. Two
CCD (Charge Coupled Device) cameras are used to process stereo images and identify the
vehicle in front, obstacles, traffic lanes and other items.
EyeSight
WARNING
Drivers are responsible for driving safely. Strive for safe driving at all
times. Always maintain a safe following distance behind the vehicle in
front of you, pay attention to your surroundings and the driving condi-
tions, operate the brake pedal and take other action as necessary in
order to maintain a safe following distance.
Never attempt to drive relying on EyeSight alone.
EyeSight is intended to assist the driver in making decisions in order to
reduce the chance of accidents or damage and lessen the burden on the
driver.
When a warning is activated, pay attention to what is in front of you and
to your surroundings, operate the brake pedal and take other action as
necessary.
This system is not designed to support driving in poor visibility or in
extreme weather conditions, or to protect against careless driving
when the driver is not paying complete attention to the road ahead. It
also cannot prevent collisions from occurring in all driving conditions.
There are limits to the EyeSight recognition performance and control per-
formance. Be sure to read the instructions concerning Adaptive Cruise
Control, the Pre-Collision Braking System, Pre-Collision Throttle
Management and Conventional Cruise Control before using them and be
sure to use them correctly. We are not liable for accidents or other prob-
lems resulting from failure to follow the instructions in this manual.
The EyeSight system in your vehicle is designed for use in countries in
which traffic operates on the right-hand side of the road. EyeSight for
LHD vehicles such as yours is not designed for use in countries in which
vehicles are driven on the left-hand side of the road.
The system may not operate correctly under the conditions listed below. When
these conditions occur, turn off the Pre-Collision Braking System. Also, do not
use Adaptive Cruise Control.
- The tire pressure is not correct.*
- The temporary spare tire is installed on any wheel.*
- Tires that are worn or have large variations in wear conditions are installed.*
- Tires other than those of the designated size are installed.*
- An emergency repair is performed using the flat tire repair kit.
- The suspension has been modified.
- Tire chains are installed.
- The headlights are dirty or the optical axes are not aligned correctly. (Objects
are not correctly illuminated and are difficult to detect.)
- Vehicle operation has become compromised due to an accident or malfunc-
tion.
- The brake warning light is illuminated.
- The vehicle is tilted due to a heavy cargo load.
- The maximum number of occupants and/or the gross vehicle weight rating is
exceeded.
*The wheels and tires have functions that are critically important. Be sure to
use the correct ones. For details, refer to the Owner’s Manual for your vehicle.
The system may not operate correctly when towing a trailer or another vehicle.
Do not use Adaptive Cruise Control in these situations.
B8192BE-C.book 2 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
3
Continued on next page
CAUTION
The characteristics of the stereo cameras are similar to those of human
eyes. For this reason, conditions that make it difficult for the driver to see
in the forward direction have the same effect on the stereo cameras and
make it difficult for the system to detect vehicles, obstacles and traffic
lanes.
Detection by the EyeSight system is limited to objects that are within the
range of the stereo cameras’ field of vision. Also, after an object enters the
range of the cameras’ field of vision, it may take some time for the system
to detect it as a controllable target and warn the driver.
Under the conditions listed below, it will become more difficult for the sys-
tem to detect the vehicle in front, motorcycles, bicycles, pedestrians and
obstacles on the road and lane markers, and EyeSight may temporarily
stop operating. However, the system will resume operation once these
conditions have improved and the vehicle is driven for a short period of
time.
- Bad weather (for example heavy rain, a blizzard or thick fog). In particu-
lar, the system is more likely to temporarily stop operating when there is
an oil film adhering to the windshield, a glass coating has been applied
or old wipers are used.)
- When affected by strong light from the front (sunlight or headlight
beams, etc.)
- The windshield has become fogged, or snow, dirt, dust or frost has
adhered to it, reducing the stereo cameras’ field of view.
- The vehicle is tilted at an extreme angle due to loaded cargo or other
factors.
- When the stereo cameras’ field of view is obstructed (for example by a
canoe on the roof of the vehicle)
- When visibility is poor due to sand, smoke or water vapor in the air, or
when the vehicle in front or oncoming traffic causes water, snow, dirt or
other substances to obscure the view
S00713
Low objects surrounding the vehicle cannot
be detected.
B8192BE-C.book 3 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
4
Continued from previous page
- When passing through the entrance or exit of a tunnel
- When the rear aspect of the vehicle in front is low, small or irregular (for
example a low bed trailer, etc.)
- When there is a fence, a wall or a shutter, etc. with a uniform pattern (a
striped pattern, brick, etc.) or with no pattern in front
- When there is a wall or door made of glass or a mirror in front
- When water droplets or dirt have not been fully wiped off the windshield
- When driving at night or in a tunnel when there is a vehicle in front that
does not have its taillights on
- When passing a banner or flag, low branches on a tree or thick/tall vege-
tation
- On steep uphill or downhill grades
- When the front of the cameras are obstructed by a hand, etc.
- When it is completely dark and no objects are detected
- When the area around the vehicle has a uniform color (such as when
completely covered in snow, etc.)
- When the stereo camera lenses are dirty due to fingerprints, etc.
- When accurate detection is not possible due to reflections in the front
windshield
- When the stereo cameras have become misaligned due to a strong
impact
Under the conditions listed below, EyeSight may temporarily stop
operating. If this occurs, EyeSight will resume operating when the
conditions improve.
- The temperature inside the vehicle is high, such as after the vehicle was
left in bright sunshine, or the temperature inside the vehicle is low, such
as after the vehicle was left in an extremely cold environment.
- Immediately after the engine starts
When there is a malfunction in the EyeSight system, turn off the Pre-Colli-
sion Braking System (refer to page 51) and the Lane Departure Warning
(refer to page 60), and stop using the Adaptive Cruise Control. Contact a
SUBARU dealer and have the system inspected.
B8192BE-C.book 4 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
5
NOTE
EyeSight records and stores the following data when the secondary brak-
ing of the Pre-Collision Braking System is operated. It does not record con-
versations or other audio data.
- Stereo camera image data
- Distance from the vehicle in front
- Vehicle speed
- Steering wheel turning angle
- Lateral movement with regard to the direction of travel
- Accelerator pedal operation status
- Brake pedal operation status
- Select lever position
- Data related to ABS, Vehicle Dynamics Control and Traction Control
Function
SUBARU and third parties contracted by SUBARU may acquire and use
the recorded data for the purpose of vehicle research and development.
SUBARU and third parties contracted by SUBARU will not disclose or
provide the acquired data to any other third party except under the fol-
lowing conditions.
• The vehicle owner has given his/her consent.
• The disclosure/provision is based on a court order or other legally
enforceable request.
• Data that has been modified so that the user and vehicle cannot be
identified is provided to a research institution for statistical processing
or similar purposes.
B8192BE-C.book 5 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
6
The stereo cameras are installed at the posi-
tions of the front map lights.
Handling of the Stereo Cameras
CAUTION
A function is included that will automatically detect that the fronts of the
stereo cameras are dirty. However it is not 100% effective.
Under certain conditions, this function may fail to detect that the fronts of
the stereo cameras have become dirty. In addition, this function may not
detect that there is snow or ice on the windshield close to the stereo cam-
eras. In such conditions, the system may not maintain a suitable distance
between vehicles; therefore, do not use Adaptive Cruise Control and be
sure to pay attention to what is ahead of you while driving. Also be sure to
keep the windshield clean at all times (indicated by ). When this func-
tion detects that the fronts of the stereo cameras are dirty, no EyeSight
functions are activated except for Conventional Cruise Control.
The stereo camera lenses are precision components. Always observe the
following precautions when handling them.
- Never touch the stereo camera lenses, and do not attempt to wipe or
clean the lenses. Doing so could cause lens damage or contamination
and lead to improper system performance.
If you ever touch a lens for any reason, be sure to contact a SUBARU
dealer.
Stereo cameras
S00883
B8192BE-C.book 6 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
7
Continued on next page
- When cleaning the front
windshield, cover the cam-
era covers with plastic
wrap, such as food wrap-
ping, or something similar
to prevent glass cleaner
from getting on the cam-
era lenses.
- If having your vehicle
washed at a service sta-
tion, etc., be sure to
request that the attendant
covers the camera covers
before washing the vehi-
cle.
Do not subject the stereo cameras to a strong impact.
Do not remove or disassemble the stereo cameras.
Do not change the positions where the stereo cameras are installed or
modify any of the surrounding structures.
Do not install an interior rearview mirror other than a genuine SUBARU
rearview mirror (such as a wide-type mirror). Also, use the rearview mirror
so that it does not obstruct the stereo cameras. Failure to do so may affect
the stereo cameras’ field of vision and could prevent the EyeSight system
from functioning properly.
S00808
S00509
B8192BE-C.book 7 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
8
Continued from previous page
Do not affix any stickers or install any accessories on the prohibited areas
shown in the illustrations below (grey zones). Doing so may affect the ste-
reo camera’ field of view and could prevent the EyeSight system from func-
tioning properly. If you must affix any stickers, such as automobile
inspection certificate stickers, or install accessories, do not cover the front
of the cameras. If abnormal EyeSight operation occurs, remove the stick-
ers or accessories.
If the top of the instrument panel is polished with chemicals or other sub-
stances, the stereo cameras may not be able to detect objects accurately
and the EyeSight system may not operate properly due to reflections in the
front windshield.
Side view Front view
Do not place any objects on top of the instrument panel and do not coat
the surface above the instrument panel with chemical liquid. The stereo
cameras may not be able to detect objects accurately and the EyeSight
system may not function properly due to reflections in the front windshield.
For details, contact a SUBARU dealer.
Do not install any wiper blades other than genuine SUBARU wiper blades.
Doing so may affect the stereo cameras’ field of vision and could prevent
the EyeSight system from functioning properly.
Replace damaged wiper blades as soon as possible. The stereo cameras
may not be able to detect objects accurately and the EyeSight system may
not function properly due to liquid remaining on the windshield.
Keep the windshield (outside and inside) clean at all times.
Never mount any device to the center air vent, as any air flow change may
impact EyeSight performance.
Do not place any stickers or accessories on the windshield (outside or
inside). If you have to do so (for example, legally required), avoid the area
in front of the camera. Doing so may adversely affect the field of vision of
the stereo camera and can cause improper operation of the system.
Monitor or other accessories
S00884
本文 .fm 8 ページ 2014年9月16日 火曜日 午後4時32分
About EyeSight
9
Do not use any glass coating agents or similar substances on the wind-
shield. Doing so may prevent the system from operating correctly.
If there are scratches or cracks on the front windshield, contact a SUBARU
dealer.
To have the front windshield replaced or repaired, contact a SUBARU
dealer. Do not install a front windshield other than a genuine SUBARU
front windshield. The stereo cameras may not be able to detect objects
accurately and the EyeSight system may not operate properly.
本文 .fm 9 ページ 2014年9月16日 火曜日 午後4時32分
About EyeSight
10
EyeSight includes the following seven functions.
Adaptive Cruise Control
This function maintains the set vehicle speed and when there is a vehicle in front in the
same traffic lane, it tracks the speed of the vehicle in front up to the maximum of the set
vehicle speed.
* Refer to page 21.
Pre-Collision Braking System
This function uses a following distance warning feature to warn the driver to take evasive
action when there is the possibility of a collision with a vehicle or obstacle in front of the
driver’s vehicle. If the driver still does not take evasive action, the brakes are quickly applied
automatically just before the collision in order to reduce the collision damage or, if possible,
prevent the collision.
* Refer to page 43.
Pre-Collision Throttle Management
This function reduces accidental forward movement caused by the selector lever being
placed in the wrong position or the accelerator pedal being accidently depressed, or
depressed too strongly.
* Refer to page 52.
Lane Departure Warning
This function warns the driver when the vehicle is about to depart the traffic lane during driv-
ing.
* Refer to page 58.
Lane Sway Warning
This system detects vehicle drifting caused by driver fatigue, failure to concentrate on the
road, inattention, strong crosswinds or other factors, and warns the driver.
* Refer to page 61.
Lead Vehicle Start Alert
This function notifies the driver when the vehicle in front has started moving but the driver’s
vehicle has not.
* Refer to page 64.
EyeSight Functions
B8192BE-C.book 10 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
11
Conventional Cruise Control
In this mode, the system maintains a constant vehicle speed. Tracking of the vehicle in front
does not occur. This function can be used even when the stereo cameras have temporarily
stopped operating. (Refer to page 77.) (This function is used by switching from Adaptive
Cruise Control to Conventional Cruise Control.)
* Refer to page 65.
NOTE
EyeSight does not operate when the engine is not running.
B8192BE-C.book 11 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
12
Combination meter
<Meter display (U.S. models)>
Instrument panel display layout
S01001
SI-DRIVE indicator lights
X-mode indicator
light
Customization display
EyeSight temporary
stop indicator
Set vehicle speed display
READY indicator
SET indicator
Steering wheel indicator
Lane indicator (Right)
Lane indicator (Left)
Following distance setting
indicator
Lead vehicle indicator
Selector indicator /
shift position indicator
Conventional
Cruise Control
indicator
Adaptive Cruise
Control indicator
EyeSight
warning
light
Lane Departure Warning
OFF indicator light
SPORT
Eye
Sight
Stay
Alert
Obstacle
Detected
Lane
Departure
Pre-Collision Braking System
OFF indicator light
MPH
miles
B8192BE-C.book 12 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
13
<Meter display (Canada models)>
S01002
SI-DRIVE indicator lights
X-mode indicator
light
Customization display
EyeSight
warning
light
Lane Departure Warning
OFF indicator light
Pre-Collision Braking System
OFF indicator light
EyeSight temporary
stop indicator
Set vehicle speed display
READY indicator
SET indicator
Steering wheel indicator
Lane indicator (Right)
Lane indicator (Left)
Following distance setting
indicator
Lead vehicle indicator
Selector indicator /
shift position indicator
Conventional
Cruise Control
indicator
Adaptive Cruise
Control indicator
B8192BE-C.book 13 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
14
CRUISE indicator
These indicators are displayed when the main cruise control is pushed.
: Adaptive Cruise Control (Adaptive Cruise Control indicator)
: Conventional Cruise Control (Conventional Cruise Control indicator)
* Refer to page 28.
SET indicator [Adaptive Cruise Control/Conventional Cruise Control]
is displayed when cruise control is set. When the vehicle stops, the indicator will blink
until the cruise control is cancelled.
* Refer to page 29.
READY indicator
is displayed when Adaptive Cruise Control can be set.
* Refer to page 28.
Lead vehicle indicator
When Adaptive Cruise Control is set, this indicator will be displayed when a vehicle in
front has been detected.
This indicator and the following distance setting indicator will blink in the following cases.
- The Lead Vehicle Start Alert is active.
- The Pre-Collision Braking System is active.
- The “brake more” warning is active.
- Pre-Collision Throttle Management is active.
These indicators also flash if, after Adaptive Cruise Control is set, it is automatically can-
celed because a vehicle in front of your vehicle is now out of the detectable range of the
EyeSight cameras.
* Refer to page 30.
Following distance setting indicator
(Following distance setting) Indicates the following distance setting that was set with
the following distance setting switch.
This indicator blinks in the following cases.
- The “brake more” warning is active.
- The Pre-Collision Braking System is active.
- Pre-Collision Throttle Management is active.
* Refer to page 36.
Set vehicle speed display
Displays the set vehicle speed.
* Refer to page 28.
SI-DRIVE
*
mode indicator
Indicates the current SI-DRIVE mode.
*
SI-DRIVE refers to SUBARU Intelligent Drive.
* Refer to page 19.
B8192BE-C.book 14 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
15
Selector indicator/shift position indicator
Displays the selector lever position or the selected gear position.
For turbo models, when the Adaptive Cruise Control / Conventional Cruise Control is set
while S# (Sports Sharp mode) of SI-DRIVE is selected, the display switches from the gear
position to the D position.
Lane indicator
When the Lane Departure Warning is activated, both the left and right indicators flash
simultaneously.
When the Lane Sway Warning is activated, the left and right indicators flash alternately.
* Refer to pages 58 and 61.
Steering wheel indicator
Flashes when the Lane Departure Warning or Lane Sway Warning is active.
* Refer to pages 58 and 61.
EyeSight temporary stop indicator
If a malfunction occurs in the EyeSight system, the Pre-Collision Braking System OFF
indicator light and the Lane Departure Warning OFF indicator light illuminate and a sym-
bol from “E1” to “E3” will be displayed on the meter display. However, when the main
cruise control is in the OFF position, the symbol will not be displayed.
When it is displayed, none of the EyeSight functions can be used except for Conventional
Cruise Control.
* Refer to page 77.
Customization display
The settings of the alarm volume, the lead vehicle acquisition sound and the lead vehicle
start alert function can be customized when all of the following conditions are met: the
engine is running, the main cruise control is in the OFF position and the selector lever is in
the P position.
* Refer to page 79.
EyeSight warning light
This indicator illuminates or flashes when a malfunction occurs in the EyeSight system.
It also illuminates when the ignition switch is turned to the ON position and then it turns off
approximately 5 seconds after the engine starts.
When it is illuminated or flashing, none of the EyeSight functions can be used (including
Adaptive Cruise Control and the Pre-Collision Braking System, etc.).
* Refer to page 76.
B8192BE-C.book 15 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
16
Lane Departure Warning OFF indicator light
This indicator illuminates when the Lane Departure Warning and Lane Sway Warning are
off.
It also illuminates when the ignition switch is turned to the ON position, and then turns off
approximately 7 seconds after the engine starts.
* Refer to page 60.
Pre-Collision Braking System OFF indicator light
Illuminates when the Pre-Collision Braking System and Pre-Collision Throttle
Management are off.
It also illuminates when the ignition switch is turned to the ON position, and then turns off
approximately 7 seconds after the engine starts.
* Refer to pages 51 and 57.
Multi function display
Your own vehicle speed indicator
Indicates your own vehicle speed with a red indicator.
Set vehicle speed indicator
Indicates the set vehicle speed.
* Refer to page 29.
Set vehicle speed display
Your own vehicle
indicator
Your own vehicle
speed indicator
Lead vehicle
indicator
Lead vehicle
distance indicator
S00885
本文 .fm 16 ページ 2015年3月30日 月曜日 午後4時12分
About EyeSight
17
Your own vehicle indicator
When the brake pedal is depressed or the brake control function is active, the brake light on
the indicator illuminates in red.
Lead vehicle indicator
While the Adaptive Cruise Control is set to on, this indicator is displayed when a vehicle is
detected in front.
* Refer to page 30.
Lead vehicle distance indicator
While the Adaptive Cruise Control is set to on, the distance to the vehicle in front is visually
displayed when following the vehicle in front.
NOTE
For Canada models, if an EyeSight warning or malfunction is detected, a
corresponding message will be displayed on the multi function display.
However for USA models, only a malfunction message will be displayed.
* Refer to page 81.
B8192BE-C.book 17 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
18
Steering wheel switches
(CRUISE) switch
Switches cruise control
*
on/off.
* Refer to page 28.
When this switch is pressed and “ ” or “ ” appears on the instrument panel, the
main cruise control is on.
*
Adaptive Cruise Control and Conventional Cruise Control
SET/- switch
Can be used to set cruise control
*
.
Can be used to reduce the set vehicle speed (when cruise control
*
is currently set).
* Adaptive Cruise Control and Conventional Cruise Control
RES/+ switch
After cruise control
*
is canceled, this switch can be used to resume the cruise control
function at the vehicle speed that was previously set.
Can be used to increase set vehicle speed (when cruise control
*
is currently set).
*
Adaptive Cruise Control and Conventional Cruise Control
Switch layout
S00812
Switch
Switch
(CRUISE) switch
(INFO)/SET switch
(Following distance
setting) switch
CANCEL switch
RES/+ switch
SET/- switch
<Turbo>
<Except for turbo>
S/I switch
S switch
I switch
S#/I switch
B8192BE-C.book 18 ページ 2014年9月16日 火曜日 午後2時25分
About EyeSight
19
CANCEL switch
Cancels cruise control
*
.
*
Adaptive Cruise Control and Conventional Cruise Control
* Refer to pages 37 and 71.
(Following distance setting) switch
Can be used to switch the set following distance in 3 stages: Far, Medium and Close (only
when Adaptive Cruise Control is set).
* Refer to page 36.
When the (CRUISE) switch is on, press and hold this switch for approximately 2
seconds or longer to select Adaptive Cruise Control or Conventional Cruise Control.
SI-DRIVE
*
switch
Selects the tracking characteristics linked with the SI-DRIVE (only when adaptive cruise
control is set).
*
SI-DRIVE refers to SUBARU Intelligent Drive.
Turbo model
- S/I switch
Switches between I (Intelligent mode) and S (Sports mode) every time it’s pressed.
While S# (Sports Sharp mode) is selected, press the switch to change to S (Sports
mode).
- S#/I switch
Press the switch to change to S# (Sports Sharp mode).
While S# (Sports Sharp mode) is selected, press the switch will change to I (Intelligent
mode).
Except for turbo model
- S switch
Press this switch to change to S (Sports mode).
- I switch
Press this switch to change to I (Intelligent mode).
SI-DRIVE cooperative control
The characteristics of adaptive cruise control will vary depending on the SI-DRIVE mode
selection.
I (Intelligent mode) selected Tracks the vehicle in front speed with smooth motions.
S (Sports mode) selected
Vehicle in front tracking performance is given priority,
resulting in tracking with frequent changes in speed.
S# (Sports Sharp mode)
selected
The same vehicle in front tracking as S (Sports mode) is
performed. The S# (Sports Sharp) response is provided
when the driver operates the accelerator pedal.
B8192BE-C.book 19 ページ 2014年9月16日 火曜日 午後2時25分
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89

Subaru 2015 Forester Owner's manual

Category
Cars
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI