USER GUIDE
enUS
2iGRILL 3
|
USER GUIDE
TABLE OF CONTENTS
Enhance Your Assembly
Experience
Download the free BILT
™
app for
step-by-step 3D instructions showing
how to install your iGRILL 3.
Before you begin
Box Contents ..........................................3
Installation ...........................................4
SPIRIT II...........................................................4
GENESIS II & GENESIS II LX ........................................12
Quick Start Instructions ..............................23
Important Information ...............................28
Intended Use .................................................... 28
Meat Probe Use.................................................. 28
Disposal Requirements .......................................... 29
Technical Specifications......................................... 29
FCC Compliance ................................................. 29
IC Compliance ................................................... 29
3iGRILL 3
|
USER GUIDE
AA
+
AA
AA
+
+
Box Contents
Meat Probe
Red
Coloured
Probe
Indicator
Meat Probe
Yellow
Coloured
Probe
Indicator
Probe Wrap
WARNING!
Probe gets hot.
Use mitts.
Battery Pack
Battery Pack Bracket
iGRILL 3
AA Batteries (3)
Battery Wire
LP Magnet
LP Fuel Sensor
Probe Wrap
Wire Retention Clip
4iGRILL 3
|
USER GUIDE
Installation
Remove cover plate. Some models may have screws.
1
1
5iGRILL 3
|
USER GUIDE
Installation
2
Install batteries. Do not mix old and new batteries. Do not mix alkaline, standard or
rechargeable batteries.
2
-
AA
AA
AA
6iGRILL 3
|
USER GUIDE
Installation
3a
Install bracket on the inside of the wheelframe. Snap battery pack into bracket.
Connect battery wire to the battery pack.
3
a) b)
7iGRILL 3
|
USER GUIDE
Installation
3b
Route battery wire through front of side table. Connect battery wire to the iGRILL.
3
a) b)
8iGRILL 3
|
USER GUIDE
Installation
4a
Install magnet.
4
a) b)
9iGRILL 3
|
USER GUIDE
4b
Installation
Connect LP fuel sensor.
4
a) b)
10iGRILL 3
|
USER GUIDE
Installation
5
Snaps into place. No screws required.
5
11iGRILL 3
|
USER GUIDE
Installation
6
Remove adhesive liner from wire retention clip. Apply clip to cleansed area underneath
sidetable. Wire(s) must be secured using clip.
6
12iGRILL 3
|
USER GUIDE
Installation
1
Remove cover plate. Some models may have screws - OR -
1
13iGRILL 3
|
USER GUIDE
Installation
Remove LED fuel gauge.
1
14iGRILL 3
|
USER GUIDE
Installation
2
Install batteries. Do not mix old and new batteries. Do not mix alkaline, standard or
rechargeable batteries.
2
-
AA
AA
AA
15iGRILL 3
|
USER GUIDE
Installation
3
3
Install bracket underneath side table.
16iGRILL 3
|
USER GUIDE
Installation
4
Connect the battery wire to the battery pack. Then, snap the battery pack into the bracket.
4
17iGRILL 3
|
USER GUIDE
Installation
5
Route battery wire through front of side table. Connect battery wire to the iGRILL.
5
18iGRILL 3
|
USER GUIDE
Installation
6a
Install magnet on GENESIS II models. GENESIS II LX models already have magnet installed.
6
a) b)
19iGRILL 3
|
USER GUIDE
Installation
6b
Connect LP fuel sensor.
6
a) b)
20iGRILL 3
|
USER GUIDE
Installation
7
7
Connect lighted control knob wires. Installationon GENESIS II LX only.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
