Heartland 184598 Installation guide

STOP!

Call Us First!

DO NOT RETURN TO STORE.

For immediate help with assembly or product information

call our toll-free number:

or email:

customer service@ba ckyardproductsllc.com

Our staff is ready to provide assistance.

April through October M - F 8:00 AM to 7:00 PM EST

Saturday 8:30 AM to 4:30 PM EST

November through March M - F 8:00 AM to 5:00 PM EST

1-888-827-9056

16676

(This page intentionally left blank.)

A Backyard Products Company

05/16/2013

LIBERTY 10' x 8' (305 x 244 cm)

ASSEMBLY MANUAL

VALUE SERIES

16676

BEFORE YOU BEGIN

IMPORTANT!

READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

- CUSTOMER SERVICE -

Call: 1-888-827-9056 email: customerservice@backyardproductsllc.com

s BUILDING RESTRICTIONS AND APPROVALS

Be sure to check with local building department and homeowners association for speciﬁc restrictions and/ or requirements before building

.

s ENGINEERED DRAWINGS

Contact our Customer Service Team if engineered drawings are needed to pull local permits.

s SURFACE PREPARATION

To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are

s CHECK ALL PARTS

Inventory all parts listed on pages 5 - 7. Contact our Customer Service Team if any parts are missing or damaged.

s ADDITIONAL MATERIALS

You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.

KEEP THIS MANUAL FOR FUTURE REFERENCE

BUILDING SIZE ACTUAL FLOOR SIZE

10' x 8' (305 x 244 cm)

BASE MODEL

10' x 7' 8-5/8" (305 x 235,3 cm)

10' x 12' (305 x 365,8 cm)

ADD ONE 10' x 4'

10' x 11' 8-5/8" (305 x 357,2 cm)

2

4//,3

Safety! Always use approved safety glasses during assembly.

OptionalRequired

(%,0&5,2%-).$%239-"/,3

Look for these symbols for helpful reminders throughout this manual.

/2)%.4,5-"%2!.$42)-&/2"%34!00%!2!.#%

= Assistance Required; two or more people.

= Ensure squareness.

= Important required step or operation.

= Helpful assembly hint.

= Mark part with pencil.

= Beginning of steps for assembly or installation.

= You have ﬁ nished the assembly or installation.

= Level

❑ Gloves

Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.

Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way

negatively affect the strength or integrity of our product. (See Fig. A, B, C.)

A

❑ Safety Glasses

❑ Tape Measure

❑ Paint Tools

❑ Ladder

❑ Caulk Gun

❑ Hammer

❑ Level

FINISH

BEGIN

❑ Pencil

❑ Phillips

Screwdriver

❑ Drill / Driver

❑ 3/8" Drill Bit

❑ #2 Philips Drive Bit

❑ Tool Belt/

Nail Pouch

❑ Chalk Line

❑ Nail Gun

• gun nails

❑ Tin Snips

(for drip edge)

❑ Square

or

❑ Utility Knife

❑ Shingle Blades

B C

3

GABLE 10' x 8'

GABLE 10' x 12'

DRIP EDGE (Feet) .......................................

40 50

#15 ROOFING FELT (Sq ft. to cover) ......... 96 144

1" GALVANIZED ROOFING NAILS (lbs) ....

1/4 1/4

For rooﬁng felt.

3-TAB SHINGLES (Bundles) ......................

4 5

PAINT FOR SIDING (Gallons).....................

1-1/2 2

Use 100% acrylic latex exterior paint.

(2) coats recommended.

1" GALVANIZED ROOFING NAILS (lbs.) ... 2 3

For shingles.

Xf

Xf

!,,3):%3

XfXf

#/-0,%4).'9/523(%$

You will need these additional materials:

!$$)4)/.!,-!4%2)!,3

2%&%24/4(%"!#+/&4()3-!.5!,!.$4(%-!.5&!#452%23).3425#4)/.3

&/2).34!,,!4)/./&3().',%3$2)0%$'%!.$&%,4

PAINT FOR TRIM .............................1 Quart

Use 100% acrylic latex exterior paint.

WOOD GLUE ....................... Exterior Rated

CAULK ..............................................2 Tubes

Use acrylic latex exterior caulk

that is paintable.

&/5.$!4)/./2&,//2-!4%2)!,3

• This shed kit includes a wood ﬂoor system. It does not include any ﬂoor panels.

• See below for the additional ﬂoor panel sizes and quantities required.

• This shed does not include any leveling materials.

• See the FLOOR LEVELING section on page 9 for recommended methods and suggested materials to properly level your

ﬂoor, as this will vary depending on your speciﬁc site.

&,//20!.%,3.OT)NCLUDED

You may need ﬂoor panels and nails to complete your ﬂoor. Floor panel sizes and quantities

are shown below.

Use a minimum of 3/4" (1,9 cm) Oriented Strand Board (OSB)

3/4 x 23-7/8 x 92-5/8" (1,9 x 60,6 x 235,3 cm)

3/4 x 23-7/8 x48" (1,9 x 60,6 x 122 cm) 3/4 x 23-7/8 x 48" (1,9 x 60,6 x 122 cm)

3/4 x 48 x 92-5/8" (1,9 x 122 x 235,3 cm)

3/4 x 48 x 92-5/8" (1,9 x 122 x 235,3 cm) 3/4 x 48 x 96" (1,9 x 122 x 243,8 cm)

x1

x1 x1

x2

x2 x1

/04)/.!,-!4%2)!,3

4

GABLE 10' x 8' GABLE 10' x 12'

2%).&/2#%$Xf7//$&,//2&2!-%/04)/.!,

2%).&/2#%$Xf7//$&,//2&2!-%/04)/.!,

IMPORTANT! The included ﬂoor has been designed for general use. Depending on your speciﬁc use you may want to construct a

heavy duty ﬂoor frame by adding additional ﬂoor joists (shown below as shaded). Below is a list of additional materials (not included):

IMPORTANT! The included ﬂoor has been designed for general use. Depending on your speciﬁc use you may want to construct a

heavy duty ﬂoor frame by adding additional ﬂoor joists (shown below as shaded). Below is a list of additional materials (not included):

x5

x3

x20

x5

x40

2 x 4 x 8' (5 x 10 x 244 cm) Treated Lumber

Cut to (5) 2 x 4 x 89-1/2" (5 x 10 x 227 cm)

ea. 3" (7,6 cm) Hot Dipped Galvanized Nails

2 x 4 x 8' (5 x 10 x 244 cm) Treated Lumber

Cut to (5) 2 x 4 x 45" (5 x 10 x 114,3 cm)

2 x 4 x 8' (5 x 10 x 244 cm) Treated Lumber

Cut to (5) 2 x 4 x 89-1/2" (5 x 10 x 227 cm)

ea. 3" (7,6 cm) Hot Dipped Galvanized Nails

Optional 12" (30,5 cm) spacing

Standard 24" (61 cm) spacing

./4%3

5

GABLE 10' x 8'

GABLE 10' x 12'

0!243)$%.4)&)#!4)/.!.$3):%3

$//2 4253342)- &,//2

7!,,

Treated lumber is stamped:

0!243,)34

INVENTORY YOUR PARTS before you begin.

We suggest sorting parts by the category they are listed in.

ZJ

x1

5/8 x 3 x 72" (1,6 x 7,6 x 183 cm)

OO

x2

2 x 3 x 69" (5 x 7,6 x 175,3 cm)

WOOD SIZE CONVERSION CHART

Nominal Board Size Actual Size

1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)

2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)

2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)

1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)

10x8'

2 x 4 x 65-7/8" (5 x 10 x 167 cm)

x6

CV

2 x 3 x 54-5/16" (5 x 7,6 x 138 cm)

x4

CD

5/8 x 3 x 14" (1,6 x 7,6 x 35,5 cm)

x8

ZZ

Part identiﬁcation is

stamped on some parts.

• Check these locations for part stamp.

RS

6 x 24" (15 x 61 cm)

x6

x1

2 x 3 x 22-1/8" (5 x 7,6 x 56 cm)

LT

x4

2 x 3 x 72" (5 x 7,6 x 183 cm)

OY

x4

7/16 x 2-1/2 x 24-3/4" (1,1 x 6,3 x 62,9 cm)

x6

2 x 3 x 69" (5 x 7,6 x 175,3 cm)

OV

x4

2 x 3 x 77" (5 x 7,6 x 196 cm)

PB

x2

2 x 3 x 92-5/8 " (5 x 7,6 x 235,3 cm)

PM

x2

2 x 3 x 94-1/2" (5 x 7,6 x 240 cm)

PR

2 x 3 x 46-1/4" (5 x 7,6 x 117,5 cm)

x2

NH

1 x 3 x 94-3/4"

(2,5 x 7,6 x 240,1 cm)

x2

HS

1 x 3 x 5" (2,5 x 7,6 x 12,7 cm) ONE USED AS A GAUGE BLOCK FOR 3/4" (19 mm) MEASUREMENT

x5

GAA

x4

1 x 3 x 8-1/4" (2,5 x 7,6 x 21 cm)

GBA

x4

3/4 x 6-1/4 x 11-7/8" (1,9 x 15,8 x 30 cm)

x2

2 x 4 x 48" (5 x 10 x 122 cm)

x6

2 x 4 x 89-1/2" (5 x 10 x 227 cm)

3/4"

(19 mm)

LEFT PAINTED GREEN

RIGHT PAINTED RED

x2

2 x 4 x 72" (5 x 10 x 183 cm)

6

GABLE 10' x 8' GABLE 10' x 12'

7!,,0!.%,$//230!243,)34

2//&0!.%,3

&!34%.%2(!2$7!2%"!'3HOWN!CTUAL3IZE

.!),"/8%33HOWN!CTUAL3IZE

3/&&)40!.%,3

x22

x45

x28

x118

x71

3" (7,6 cm)

2" (5,0 cm)

3/4" (19 mm)

1-1/4" (3,2 cm)

x1 BOXES

x4 BOXES

x2

x2 x4

3/8 x 48 x 72"

(1 x 122 x 183 cm)

x1 x1

x1x1

x1

RIGHT DOOR

x1

LEFT DOOR

x2

3/8 x 5 x 93-1/4" (0,9 x 12,7 x 236,9 cm)

3/4" (19 mm) 3/4" (19 mm) 3/4" (19 mm)

64" Metal Threshold

Bagged seperately / special coating

x1

x4

x1

x7

x11

Roof panels are

7/16" (11 mm)

thick.

x2x2

19" x 96"

(48 x 244 cm)

48" x 96"

(122 x 244 cm)

$//2(!2$7!2%.OT!CTUAL3IZE

7

GABLE 10' x 8'

GABLE 10' x 12'

0!243)$%.4)&)#!4)/.!.$3):%3

Treated lumber is stamped:

Xf%84%.$%20!243,)34

INVENTORY YOUR PARTS before you begin.

We suggest sorting parts by the category they are listed in.

WOOD SIZE CONVERSION CHART

Nominal Board Size Actual Size

1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)

2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)

2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)

1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)

10x4'

Part identiﬁcation is

stamped on some parts.

• Check these locations for part stamp.

RS

Roof panels are 7/16" (1,1 cm) thick

x9

2 x 4 x 45" (5 x 10 x 114,3 cm)

x2

2 x 4 x 72" (5 x 10 x 182,9 cm)

x2

2 x 4 x 48" (5 x 10 x 122 cm)

2//&0!.%,3 42)- 2!&4%237!,,0!.%,3 7!,, &,//2

2 x 3 x 48" (5 x 7,6 x 122 cm)

x2

NK

1 x 3 x 48" (2.5 x 7,6 x 122 cm)

x2

FO

6 x 24" (15 x 61 cm)

x4

7/16 x 2-1/2 x 48" (1,1 x 6,3 x 122 cm)

x2

3/8 x 5 x 48" (0,9 x 12,7 x 122 cm)

x2

7/16 x 47-7/8 x 48" (1,1 x 121,6 x 122 cm)

x2

7/16 x 19 x 48" (1,1 x 48 x 122 cm)

x2

3/8 x 48 x 72" (1 x 122 x 183 cm)

x2

2 x 3 x 69" (5 x 7,6 x 175,3 cm)

x4

OV

2 x 4 x 65-7/8" (5 x 10 x 167 cm)

x4

CV

8

A

B

C

4"

(10 cm)

3-1/2"

(8,9 cm)

D

CONCRETE FOUNDA TION

If you choose to install your kit on a concrete slab refer to the diagram below.

Attach the sill plates on the foundaton as shown, and continue on to page 19.

ABActual Floor SizeBuilding Size

• A treated 2 x 4" (5 x10 cm) sill plate is required when installing your shed on concrete.

Purchase full length treated lumber, or butt shorter pieces end-to-end and seal seams with caulk.

• Use a high quality exterior grade caulk beneath all sill plates.

• Fasten 2 x 4" (5 x 10 cm) sill plates to slab using approved concrete anchors (fasteners not included)

.

• Check local code for concrete foundation requirements.

120" (305 cm)

85-5/8" (217,4 cm)

133-5/8" (339,4 cm)

10'x 7'-8-5/8" (305 x 235,3 cm)

10'x 11'-8-5/8" (305 x 357,2 cm)

10'x 8' (305 x 244 cm)

10'x 12' (305 x 365,8 cm)

92-5/8" (235,3 cm)

151-1/2" (384,8 cm)

140-5/8" (357,2 cm) 184-7/8" (469,5 cm)

Treated Sill Plate

Caulk between

sill plate and

concrete.

10' x 8' Building Requires:

10' x 12' Building Requires:

2 x 4 x 10' (5 x 10 x 305 cm)

x2

2 x 4 x10' (5 x 10 x 305 cm)

x2

2 x 4 x 8' (5 x 10 x 244 cm)

x2

2 x 4 x 12' (5 x 10 x 365,8 cm)

x2

Sill plates MUST be treated lumber.

Caulk

x1

Allow new concrete slabs to cure for at least seven (7) days.

ABC DActual Floor SizeBuilding Size

GABLE 10' x 8' GABLE 10' x 12'

9

• 3" Screws angled into 4x4.

• (2) at each point frame

and 4x4 touch.

Runners are generally

12" (30,5 cm) from

ends of floor frame

and under seams.

FLOOR FRAME NOT INCLUDED

OPTIONAL WOOD FRAME FLOOR LEVELING OPTIONS

There are multiple ways to level your floor frame. Our recommended leveling method is shown below.

Leveling materials are not included in this kit.

PREFERRED METHOD - 4x4 TREATED RUNNERS (Typical for 10' x 8' Kit)

• Level under 4x4 runners only.

• Locate leveling material 12" from ends of runners and no more than 48" apart.

• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use

shingles in direct contact with ground.

• For best results and aiding in water drainage use gravel under each concrete block.

LEVELING METHODS

MATERIAL REQUIRED

x2

4" x 4" x 10' (10 x 10 x 305 cm) Treated Lumber

x3

4" x 4" x 12' (10 x 10 x 365,8 cm) Treated Lumber

Use only wood treated for ground contact and fasteners approved for use with treated wood.

Always support frame seams.

Leveling higher than 16" not recommended.

LEVELING MATERIALS

Gravel

2x4 Treated Lumber

Solid Masonry Blocks in 1", 2", 4" or 8" thickness

Asphalt Shingles

4" Block

8" Block

Gravel

Do not exceed 16".

4x4 Runner

Shingle

Maximum between leveling

material locations.

48"

12"

2x4 Treated Lumber

2" Block

Level

12"

10' x 8'

10' x 12'

Fig. B

x24

x48

3" (7,6 cm)

Fasteners for Frame to 4"x 4".

(3" Screws shown as one option.)

Minimum 3" screws / exterior grade.

DOOR

Fig. A

12"

(30,5 cm)

12"

(30,5 cm)

Measurements to

centers of 4x4's.

GABLE 10' x 8'

GABLE 10' x 12'

10

GABLE 10' x 8' GABLE 10' x 12'

DOOR

HINT:

For easier nailing

stand on frame.

Use two 3" nails at each mark.

PARTS REQUIRED:

x6

x2

x28

48"

(122 cm)

72"

(183 cm)

89-1/2"

(227 cm)

92-5/8"

(235 cm)

Orient parts as shown on ﬂat surface. Measure and mark from end of boards.

fXf&,//2&2!-%

3" (7,6 cm)

2 x 4 x 72" (5 x 10 x 183 cm) Treated Wood

2 x 4 x 89-1/2" (5 x 10 x 227 cm) Treated Wood

2 x 4 x 48" (5 x 10 x 122 cm) Treated Wood

Center

on marks.

Center

on marks.

120"

(305 cm)

48"

(122 cm)

48"

(122 cm)

24"

(61 cm)

72"

(183 cm)

96"

(244 cm)

Offset Seam

Flush

at ends.

BEGIN

2

1

DOOR

You have ﬁnished your 10' x 8' ﬂoor frame. If building 10' x 12' kit go to page 12.

FINISH

3

Toenailing

11

DOOR

• 3" Screw angled into 4x4.

• (2) at each point frame and

4x4 touch.

LEVELING & SQUARING A 10 x 8' FLOOR FRAME

• FOR 10' x 12', SKIP TO PAGE 12

FINISH

5

BEGIN

2

3

4

1

Use level and check the frame is level before applying floor panels.

Check for frame squareness by measuring diagonally across corners. If the

measurements are the same, the frame is square. The diagonal measurement

will be approximately 151-1/2" (385 cm).

When the frame is level and square, secure one side of frame to 4x4 runners using one fastener

at ends of each runner. At the opposite end of the frame, secure the frame to 4x4 runners with

one fastener at ends of each runner making sure the frame remains square (Fig. A).

Once the floor frame is level and square fasten the frame at each point the frame contacts the

4x4 runners (Fig. B). Go to page 15.

See page 9 for the preferred floor leveling method.

First, secure

at ends with

one fastener.

Second,

secure at

ends with

one fastener.

151-1/2"

(385 cm)

151-1/2"

(385 cm)

Fig. A

Fig. B

12"

(30,5 cm)

12"

(30,5 cm)

Runners are generally

12" (30,5 cm) from

ends of floor frame

and under seams.

LEVEL AND SQUARE FLOOR FRAME

Before attaching floor decking, it is important to level and square the floor frame.

A level and square floor frame is required to correctly construct your shed.

GABLE 10' x 8'

GABLE 10' x 12'

12

GABLE 10' x 8' GABLE 10' x 12'

2 x 4 x 45" (5 x 10 x 114,3 cm)

2 x 4 x 48" (5 x 10 x 122 cm)

2 x 4 x 72" (5 x 10 x 183 cm)

Offset Seam

Toenailing

HINT:

For easier nailing

stand on frame.

Section 2

Section 1

3

2

1

3" (7,6 cm)

Use two 3" nails at each mark.

Orient parts as shown on ﬂat surface to build back section 2.

Measure and mark each dimension from end of boards.

Follow steps 1-3 on page 10 to build front 10' x 8' ﬂoor section 1.

PARTS REQUIRED:

Flush

at ends.

Center on

marks.

45"

(114,3 cm)

48 "

(122 cm)

48 "

(122 cm)

1-1/2"

(3,8 cm)

120"

(305 cm)

48"

(122 cm)

48"

(122 cm)

24"

(61 cm)

72"

(183 cm)

96"

(244 cm)

72"

(183 cm)

x2

x28

x2

x6

Xf&,//2&2!-%

BEGIN

You will build two ﬂoor sections.

Offset Seam

DOOR

13

DOOR

GABLE 10' x 8'

GABLE 10' x 12'

(4) Nails per side,

stagger pattern.

140-5/8"

(357,2 cm)

120"

(305 cm)

Put both ﬂ oor sections together and attach as shown using 3" nails.

4

You have ﬁ nished your ﬂ oor frame. Proceed to level and square frame.

Xf&,//2&2!-%

FINISH

5

3" (7,6 cm)

x20

./4%3

Section 2

Section 1

14

Runners are generally

12" (30,5 cm) from

ends of floor frame

and under seams.

• 3" Screw angled into 4x4.

• (2) at each point frame and

4x4 touch.

Fig. B

Fig. A

(30,5 cm)

12"

(30,5 cm)

12"

DOOR

Second,

secure at

ends with

one fastener.

First, secure

at ends with

one fastener.

184-7/8"

(469,5 cm)

184-7/8"

(469,5 cm)

LEVELING & SQUARING A 10 x 12' FLOOR FRAME

BEGIN

2

3

4

1

Use level and check the frame is level before applying floor panels.

Check for frame squareness by measuring diagonally across corners. If the measurements are the

same, the frame is square. The diagonal measurement will be approximately 184-7/8" (469,5 cm).

When the frame is level and square secure one side of frame to the 4x4 runners using one

fastener at ends of each runner. At the opposite end of the frame, secure the frame to 4x4

runners with one fastener at ends of each runner making sure the frame remains square (Fig. A).

Once the floor frame is level and square fasten the frame at each point the frame contacts the 4x4

runners (Fig. B). Go to page 17.

See page 9 for the preferred floor leveling method.

FINISH

5

LEVEL AND SQUARE FLOOR FRAME

Before attaching floor decking, it is important to level and square the floor frame.

A level and square floor frame is required to correctly construct your shed.

GABLE 10' x 8' GABLE 10' x 12'

15

GABLE 10' x 8'

GABLE 10' x 12'

D

OOR

Fig. C

151-1/2"

(385 cm)

151-1/2"

(385 cm)

Attach the 48 x 92-5/8" panel with the rough side up (painted-grid lines side)

with the 48" edge and corner ﬂush to the ﬂoor frame (Fig A). Secure panel

with two 2" nails in the corners.

Move to the opposite end. Using the long edge of the panel as a lever move the

panel side-to-side until the top corner is ﬂush to the ﬂoor frame (Fig. B).

Secure panel with two 2" nails in the corners.

2

BEGIN

1

3

4

Continue attaching the panel using 2" nails 6" apart on edges and 12" apart inside panel.

Use a chalk line or use pre-painted grid lines to nail into joists under panel.

Ensure your ﬂoor frame is square by installing one panel and squaring frame.

Check the ﬂoor frame is square by measuring diagonally across the frame corners. If the measurements are the

same your ﬂoor frame is square. The measurement will be approximately 151-1/2" (385 cm) (Fig. C).

48" x 92-5/8"

(122 x 235,3 cm)

x1

Flush

6" (15 cm) edges of panel.

12" (30,5 cm) inside panel.

Grid lines UP

3/4"

(19 mm)

Approximately

120"

(305 cm)

48"

(122 cm)

Flush

FLOOR PANELS NOT INCLUDED.

SEE PAGE 3 FOR PANEL SIZES

AND QUANTITIES.

PARTS REQUIRED:

92-5/8"

(235 cm)

fXf&,//20!.%,3

.OT)NCLUDED

x55

2" (5 cm)

(2) Nails

Flush

Fig. A

Flush

at top

corner

edge.

Fig. B

(2) Nails

DOOR

16

GABLE 10' x 8' GABLE 10' x 12'

48" x 92-5/8"

(122 x 235,3 cm)

x1 x1

Grid lines UP.

5/8 x 23-7/8 x 92-5/8"

(1,6 x 61 x 235 cm)

FLOOR PANELS NOT

INCLUDED. SEE PAGE 3

FOR PANEL SIZES

AND QUANTITIES.

DO

OR

Use a chalk line or grid lines on panels for 2" nails 6" apart on edges

and 12" apart inside panel. .

Continue installing panels with rough side up (painted grid lines).

5

If building the 10' x 8' kit, you have ﬁ nished Installing your ﬂ oor panels, and can

continue at p. 19. If building the 10' x 12' kit continue at page 17.

PARTS REQUIRED:

x95

fXf&,//20!.%,3

.OT)NCLUDED

6

FINISH

7

2" (5 cm)

92-5/8"

(235 cm)

120"

(305 cm)

23-7/8"

(61 cm)

48"

(122 cm)

Flush

12" (30,5 cm)

6" (15 cm)

Flush

17

GABLE 10' x 8'

GABLE 10' x 12'

92-5/8"

(235 cm)

Attach the 48 x 48" panel with the rough side up (painted-grid lines side) on

Section 2 with the 48" edge and corner ﬂush to the ﬂoor frame and Section 1.

Secure using 2" nails 6" apart on edges and 12" apart inside panel. Use

a chalk line or use pre-painted grid lines to nail into joists under panel.

2

BEGIN

1

x1

6" (15 cm) edges of panel.

120"

(305 cm)

48"

(122 cm)

12" (30,5 cm)

inside panel.

Grid lines

UP.

96"

(243,8 cm)

Flush

3/4" (1,9 cm)

Approximately

48" x 96"

(122 x 243,8 cm)

Section 2

Section 1

FLOOR PANELS NOT

INCLUDED. SEE PAGE 3

FOR PANEL SIZES

AND QUANTITIES.

PARTS REQUIRED:

fXf&,//20!.%,3

.OT)NCLUDED

x57

2" (5 cm)

D

OOR

18

GABLE 10' x 8' GABLE 10' x 12'

6" (15 cm) edges of panel.

120"

(305 cm)

48"

(122 cm)

Grid lines

UP.

23-7/8"

(61 cm)

Flush

92-5/8"

(235 cm)

x1

5/8 x 23-7/8 x 48"

(1,6 x 61 x 122 cm)

Section 2

Section 1

FLOOR PANELS NOT

INCLUDED. SEE PAGE 3

FOR PANEL SIZES

AND QUANTITIES.

fXf&,//20!.%,3

.OT)NCLUDED

Use a chalk line or grid lines on panels for 2" nails 6" apart on edges

and 12" apart inside panel. .

Continue installing panels with rough side up (painted grid lines) as shown.

3

You have ﬁ nished Installing your ﬂ oor panels. Continue on page 19.

PARTS REQUIRED:

x24

4

FINISH

5

2" (5 cm)

D

OOR

Page is loading ...

Heartland 184598 Installation guide

This manual is also suitable for

Heartland 184598 Installation guide

Related papers

Other documents