AC power to secondary
operator if required.
Low voltage to secondary
operator if required.
EXPLOSIVE
HAZARDOUS
CURRENT
INPUT
AC
POWER
OUTPUT
AC
POWER
ON
OFF
ON
OFF
BATT
TEST
J2
J8
J5
J4
SW 3
SW 1
SW 2
J3
J6
J1
H
N
G
ON
115 V OUT
TO OPERATOR
115 V UTILITY
INPUT
INVERTER OUTPUT
RESET
DIAGNOSTIC
110 V ON
BATTERY
+
—
SHDN
INVERTER
HRT BEAT
INV ON
B BAD
B OK
BULK
TRICK
TEMP
DOORKING INC.
2355-010
REV__________
H
N
G
H
N
G
Single
Battery
Second
Battery
Connected
in Parallel
DANGER!!
NEVER touch
the positive and negative
battery cables together!
Negative
(-) Black
Positive
(+) Red
NO SMOKING
NO FIRE
Plug J1 in Last
Black (-)
Red (+)
Output
Power
Input AC Power
AC Power to Operator
Low Voltage to Operator
Input
Power
Low
Voltage
• Never run high voltage and low voltage in the same conduit.
• Typical conduit configuration (not supplied).
Note: DoorKing offers a mounting post kit when no
vertical surface is available to mount the Inverter
cabinet to. Refer to the
Owner's manual.
Ground
Neutral
Hot
Ground
Neutral
Hot
Inverter Input AC Power PVC Conduit
DANGER
HIGH VOLTAGE!
1 2 3 4 5 6
7 8 9 10
To J4 terminal 7 (N.O.) and 8 (Com)
To gate operator opening device’s
terminal (N.O.) and (Com).
To gate operator opening device’s
terminal (N.O.) and (Com).
To J4 terminal 9 (N.O.)
and 10 (Com)
To gate operator
power input terminal.
To gate operator
power input terminal.
12 AWG copper wire
(High Voltage)
12 AWG copper wire (High Voltage)
Operator High Voltage PVC Conduit
Operator Low Voltage PVC Conduit
Operator High Voltage PVC Conduit
Operator Low Voltage PVC Conduit
Refer to the Owner’s manual
for complete descriptions of
the switches.
Single Operator
Secondary Operator
Mount in
an area
protected
from
extreme heat
and cold.
Black
White
Green
Note: “Optional” High
Voltage Kit black and
white wires connect the
same as shown.
J6
J8
DO NOT connect the batteries until
instructed to do so in the wiring sequence.
Connecting the battery cables will cause an ARC
usually accompanied by a “SNAP”. This is NORMAL.
Inverter
Inverter LEDs
Green - Power
Red- Overload
QUICKSTART “BASIC” GUIDELINES FOR THE MODEL 1000 INVERTER/ POWER BACK-UP SYSTEM
115 VAC Input Power Wire
Mount Cabinet on Vertical Surface
The Model 1000 should be installed by a qualified electrician. For complete
safety and installation instructions, please refer to the Owner’s manual.
DIP Switches
Gate Operator(s)
1000-066-E-9-18
A
1. OFF
2. OFF
3. ON-1 battery, OFF-2 batteries
4. OFF
5. ON
6. ON
7. ON
8. ON
WARNING! The Model 1000 produces lethal voltages.
ON
SW 3
Copyright 2018 DoorKing, Inc. All rights reserved.
Input power wire must be connected to a grounded, permanent wiring system.
Tip: It is recommended that a surge suppressor be installed on the high voltage
power wire.
A
18 AWG copper wire (Low Voltage)
1
2
4
3
3
3
3
3
3
1
J4 Connector Note: Connect the J4 terminal to the
opening device terminal connections of the gate
operator(s). When the inverter runs low on battery
power, the inverter will automatically open the gate(s).
Note: The Model 1000 operates best
when it can be installed as physically
close as possible to the equipment
that it will operate during power
outages. This reduces line loss.
Note: DoorKing’s Model 1000 Power Inverter uses a modified sine wave as the AC output.
DoorKing gate operators that use a current sensor device (ERD) have been specifically
designed to work within the limits of the Inverter’s modified sine wave. Third party vehicular
gate operators that use a current sensor device (ERD) as an inherent entrapment protection
system may experience false entrapment inputs when the inverter powers them.
Single or Primary 115 VAC Operator
Secondary 115 VAC Operator
WARNING
MOVING GATE CAN CAUSE
Operate gate only when gate area is in sight
and free of people and obstructions.
D
o not allow children to play in gate area
or operate gate.
Do not stand in gate path or walk through
path while gate is moving.
Read owner’s manual and safety instructions.
SERIOUS INJURY OR DEATH
CLASS
CERTIFIED TO
CAN/CSA C22.2 NO. 247
CONFORMS TO
ANSI/UL-325
VEHICULAR GATE OPERATOR
HP
53382
MODEL
SERIAL
VOLTS PHASE
AMPS 60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
WARNING
MOVING GATE CAN CAUSE
Operate gate only when gate area is in sight
and free of people and obstructions.
D
o not allow children to play in gate area
or operate gate.
Do not stand in gate path or walk through
path while gate is moving.
Read owner’s manual and safety instructions.
SERIOUS INJURY OR DEATH
CLASS
CERTIFIED TO
CAN/CSA C22.2 NO. 247
CONFORMS TO
ANSI/UL-325
VEHICULAR GATE OPERATOR
HP
53382
MODEL
SERIAL
VOLTS PHASE
AMPS 60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
3/4” Conduit
Knockouts
Mounting Holes
Mounting Hole
3/4” Conduit
Knockouts
Bottom
Cabinet
Back
Use appropriate hardware (not supplied) in the
existing 3 mounting holes to secure the cabinet to
a vertical surface.
DO NOT drill any additional holes in the cabinet.
Drilling produces metal filings, which can cause
shorts on the circuit board and will void the warranty.
IMPORTANT! The model 1000 can only be used with products that use a PSC (Permanent Split
Capacitor) motor. Do Not use the model 1000 on products that ultilize a motor with start windings
as the start-up amerage draw on this type of motor exceeds the maximum output available from the
model 1000 and will cause damage to the inverter. The differences in these two types of motors is
difficult to recognize, so we suggest that you contact the manufacturer to determine what type of
motor is used in their product.
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
1
3 4
2
Before Wiring Inverter:
Be sure that both the Input AC Power and Output AC Power switches are OFF and remain OFF until
ALL wiring is complete.
Important Wiring Sequence: Connect the gate operator(s). Connect the 115 VAC input AC
power wire. Connect the battery(s). Plug in J1 connector last.
After the J1 plug has been plugged in, the wiring is complete and the Input AC Power and Output AC
Power switches can be turned on to activate the system.
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DKS 1000 User manual
-
DKS 9245 User manual
-
-
-
-
-
-
-
-