ZLINE Kitchen and Bath FMTF-SS User manual

ZLINE Kitchen and Bath
Brand
ZLINE Kitchen and Bath
Model
FMTF-SS
Type
User manual

ZLINE Kitchen and Bath FMTF-SS is a pull down faucet with a single handle and a spray head. It is made of brass and features a durable construction with a sophisticated design. It is WaterSense certified, meaning it meets the EPA's criteria for water efficiency and performance, using at least 20% less water than the industry standard without sacrificing performance. It has a flow rate of 1.8 gallons per minute, providing the perfect aerated water pressure to save water, energy, and time. The faucet is easy to install and comes with all the necessary hardware.

ZLINE Kitchen and Bath FMTF-SS is a pull down faucet with a single handle and a spray head. It is made of brass and features a durable construction with a sophisticated design. It is WaterSense certified, meaning it meets the EPA's criteria for water efficiency and performance, using at least 20% less water than the industry standard without sacrificing performance. It has a flow rate of 1.8 gallons per minute, providing the perfect aerated water pressure to save water, energy, and time. The faucet is easy to install and comes with all the necessary hardware.

Kitchen Faucets
Installation Guide
and Users Manual
ZLINE created a wide range of faucet solutions delivering comfortable
elegance and undeniable quality down to the smallest detail. Brass
housing allows ZLINE faucets to be durable and provides sophistication.
It’s what’s on the inside that counts.
Behind the scenes, ZLINE’s main focus is improving water efficiency.
The faucets are manufactured with carefully hand selected materials
that undergo over 50,000 unit tests, well over the industry standard for
certification of 15,000 tests. 1.8 gal/min provides the perfect aerated
water pressure — saving water, energy, and time at the best price point in
the industry.
SAFETY INSTRUCTIONS 1
Prior to Installation
Safety Tips
Installation Preparation
Care and Maintenance
Notes
SPRING FAUCETS 3
Parts
Tools
Models:
FSNZ (Apollo Series)
FSTB (Sierra Series)
12-0140 (Van Gogh Series)
Assembly
PULL DOWN FAUCETS 9
Parts
Tools
Models:
FPBC (Castor Series)
11-0129 (Shakespeare Series)
FPBL (Edison Series)
FPTF (Gemini Series)
11-0130 (Dante Series)
11-0128 (Voltaire Series)
FPTB (Arthur Series)
13-0048 (Renoir Series)
FPNZ (Monet Series)
11-0131 (Dali Series)
Assembly
TABLE OF CONTENTS
FMTF (DA VINCI) PULL DOWN FAUCET 19
Parts
Tools
Model:
FMTF (Da Vinci Series)
Assembly
SINGLE HANDLE FAUCET 24
Parts
Tools
Models:
FFCS (Rembrandt Series)
Assembly
DOUBLE HANDLE FAUCET 30
Parts
Tools
Models:
FFCC (Mona Series)
Assembly
TROUBLESHOOTING 36
TABLE OF CONTENTS
1
Prior to Installation
Make sure that the cold and hot water lines are turned off.
Wrap all threaded connections with plumber’s tape. Always wrap in a clockwise
direction.
Cover your drain to avoid losing parts.
Do not disassemble the main faucet body, as it has been installed and commissioned
correctly and precisely before delivery to the factory.
To keep the faucet from jamming, flush the water pipe before installation.
Operating conditions: Working pressure at 0.05-1.0 MPa (including cold and hot
water pressure) with applicable water temperature: 39.2°F - 194°F.
Installation Preparation
1. Shut off the water and let the water in the current faucet drain.
2. Assemble needed tools. The tools needed for each installation are included at the
beginning of each section.
3. Loosen the hardware that keeps the current faucet in place. Remove faucet.
Care and Maintenance
To keep the product clean and shining, follow the steps below:
1. Rinse clean with water and dry with a soft cloth.
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.
3. Do not use cloth with a coarse surface.
4. Unscrew the aerator and clean when necessary.
Safety Instructions
If soldering the water connections when installing the faucet, remove the O-rings,
cartridges, and washers before applying any heat.
Protect your eyes when cutting or soldering.
Do not over tighten screws/nuts. Finger tighten, then use a wrench/Philips-head
screwdriver to tighten the fixing screw/nut until snug.
2
NOTES
Faucet Model: Purchase Order #: Date:
3
Spring Faucet
4
Tools:
Time required:
+/- 45 minutes
Wrench
Legend:
Hot Water
Warning
Cold Water
Plumber’s Tape-
Used for a watertight seal on
threaded pipe joints.
Grease
Phillips-head screwdriver
Bucket
Spring Faucet
5
Spring Kitchen Faucet Models
FSNZ (Apollo Series)
Spring Faucet
FSTB (Sierra Series)
6
Spring Kitchen Faucet Models
12-0140 (Van Gogh Series)
Spring Faucets
7
Spring Faucet
Plumbers Tape
Loosen the fixing nut and screws and
put aside.
Secure the hardware into place with
the Base O-ring, nuts, and screws.
Mount faucet to counter top.
Secure the hoses to the hot (red) and
cold (blue) lines appropriately.
8
Spring Faucet
Test the faucet.
spray head
spray head
Make sure that the spray head is
properly secured.
Review the diagram to understand the
hot, cold, and open settings.
9
Pull Down Faucets
10
Tools:
Time required:
+/- 45 minutes
Wrench
Legend:
Hot Water
Warning
Cold Water
Plumber’s Tape-
Used for a watertight seal
on threaded pipe joints.
Grease
Phillips-head screwdriver
Bucket
Pull Down Faucets
11
Pull Down Kitchen Faucet Models
FPBC (Castor Series)
Pull Down Faucets
11-0129 (Shakespeare Series)
12
Pull Down Faucets
Pull Down Kitchen Faucet Models
FPBL (Edison Series)
FPTF (Gemini Series)
13
Pull Down Kitchen Faucet Models
11-0130 (Dante Series)
Pull Down Faucets
11-0128 (Voltaire Series)
14
Pull Down Kitchen Faucet Models
FPTB (Arthur Series)
Pull Down Faucets
13-0048 (Renoir Series)
15
Pull Down Kitchen Faucet Models
FPNZ (Monet Series)
Pull Down Faucets
11-0131 (Dali Series)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

ZLINE Kitchen and Bath FMTF-SS User manual

ZLINE Kitchen and Bath
Brand
ZLINE Kitchen and Bath
Model
FMTF-SS
Type
User manual

ZLINE Kitchen and Bath FMTF-SS is a pull down faucet with a single handle and a spray head. It is made of brass and features a durable construction with a sophisticated design. It is WaterSense certified, meaning it meets the EPA's criteria for water efficiency and performance, using at least 20% less water than the industry standard without sacrificing performance. It has a flow rate of 1.8 gallons per minute, providing the perfect aerated water pressure to save water, energy, and time. The faucet is easy to install and comes with all the necessary hardware.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents