Esoteric N-01XD Owner's manual

N-01XD

D01366121B

OWNER’S MANUAL .................... 3

MODE D’EMPLOI ...................... 25

MANUAL DEL USUARIO ........... 47

Network DAC

Page is loading ...

3

English

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the AC

outlet with its POWER or STANDBY/ON switch not in the ON position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120V SUPPLY.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or equiva-

lent type.

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

Supplier’s Declaration of Conformity

Model number: N-01XD

Trade name: ESOTERIC

Responsible party:

Pioneer & Onkyo U.S.A. Corporation

Address: 22828 Lockness Avenue, Torrance, CA90501 U.S.A.

Telephone number: 1-201-785-2600

This device complies with Part.15 of FCC Rules.

Operation is subject to the following two conditions:

1) This device may not cause harmful interference

2) This device must accept any interference received, including

interference that may cause undesired operation.

Information

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valu-

able resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC, 2013/56/EU), then the chemical symbols

for those elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

5

English

Thank you for purchasing this ESOTERIC product.

Read this manual carefully to get the best performance from this

product. After reading it, keep it in a safe place with the warranty card

for future reference.

The Owner’s Manual can be downloaded from the ESOTERIC website

(--).

To use this unit, you must also use a tablet or smartphone that has

the dedicated app (free) installed and connect it to the same network

as the unit.

ATTENTION

This unit only outputs analog signals from the one selected

type of connector.

Set the analog output before use.

See “Setting mode” on page15 and “Analog output set-

ting” on page17.

Contents

IMPORTANT SAFETY INSTRUCTIONS ...............................3

Before use .........................................................6

Included accessories ...........................................6

Note about pinpoint feet .......................................6

Maintenance ...................................................6

Precautions for use ................................................6

Network connections .............................................. 7

Connections ....................................................... 8

Connecting using ES-LINK Analog .............................10

Downloading the remote app ....................................10

Names and functions of parts .....................................11

MQA (Master Quality Authenticated) ..............................12

Changing the input source .......................................12

Using the USB DAC function ......................................13

Supported operating systems .................................13

Installing the driver ............................................13

Downloading playback application ESOTERIC HR Audio Player . 13

Playing audio files .............................................14

Setting mode .....................................................15

Changing settings .............................................15

Settings 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

PCM signal upconversion setting ..............................16

Clock setting ..................................................16

PCM output gain setting ......................................17

Analog output setting .........................................17

Dimmer setting ...............................................17

Automatic display darkening setting ...........................17

Automatic power saving setting ...............................18

Settings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

D/A converter operation setting ...............................18

DSD filter setting ..............................................18

ETHERNET port LED setting ....................................19

Network input circuit power supply setting ....................19

Remote control operation setting .............................19

Settings 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Audio program update setting ................................20

Troubleshooting ..................................................20

General .......................................................20

Clock sync .....................................................21

USB connections with a computer .............................21

Restoring factory settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Specifications .....................................................22

Dimensional drawings ............................................24

MQA and the Sound Wave Device are registered trade marks of MQA

“DSD” is a registered trademark.

Microsoft and Windows are either registered trademarks or trade-

marks of Microsoft Corporation in the United States and/or other

countries.

Apple, Mac, OS X and macOS are trademarks of Apple Inc., registered

in the U.S. and other countries.

App Store is a service mark of Apple Inc.

Google Play is a trademark of Google Inc.

Wi-Fi is a trademark or registered trademark of Wi-Fi Alliance.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S.

and other countries.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective owners.

Information about copyrights and licensing related to open source

software is provided in the separate “Important Notice Regarding

Software” document.

6

Before use

Included accessories

Check to be sure the box includes all the supplied accessories shown

below. Please contact the store where you purchased this product if

any of these accessories are missing or have been damaged during

transportation.

Power cord × 1

Felt pads × 4

HDMI cable × 1

Owner’s manual (this document) × 1

Warranty card × 1

Note about pinpoint feet

High-precision metal pinpoint feet are attached to the bottom plate

of this unit.

The pinpoint feet and their stands are loose, but when the unit is

placed in position, it is supported by these pinpoint feet, which effec-

tively disperse vibrations.

Chassis

Pinpoint foot (metal)

Foot-stand (metal)

Screws that attach

foot-stand

o Apply the included felt pads to the bottoms of the foot-stands to

avoid scratching the surface where the unit is placed.

Maintenance

Use a soft dry cloth to wipe the surface of the unit clean.

For stubborn smudges, use a damp cloth that has been thoroughly

wrung out to remove excess moisture.

o Avoid allowing rubber or plastic materials to touch the unit for

long periods of time because they could damage the cabinet.

o Never spray liquid directly on this unit.

o Do not wipe with chemical cleaning cloths, thinner or other

chemical agents. Doing so could damage the surface.

V

For safety, disconnect the power plug from the

outlet before cleaning.

o Do not place anything on top of the unit.

o Do not install this unit in a location that could become hot. This

includes places that are exposed to direct sunlight or near a radia-

tor, heater, stove or other heating equipment. Moreover, do not

place it on top of an amplifier or other equipment that generates

heat. Doing so could cause discoloration or deformation.

o In order to enable good heat dissipation, leave at least 20cm (8")

between this unit and walls and other equipment when installing

it. If you put it in a rack, take precautions to prevent overheating

by leaving at least 5cm (2") open above the top of the unit and at

least 10cm (4") open behind the unit.

Failure to provide these gaps could cause heat to build up inside

and result in fire.

o Place the unit in a stable location.

o Do not move the unit during use.

o Be careful to avoid injury when moving the unit due to its weight.

Have someone help you move it if necessary.

o The voltage supplied to the unit should match the voltage printed

on the rear panel. If you are in any doubt regarding this matter,

consult an electrician.

o Do not open the body of the unit as this might result in damage

to the circuitry or cause electric shock. If a foreign object should

get into the unit, contact your dealer.

o When removing the power plug from the wall outlet, always pull

directly on the plug; never yank on the cord.

o The ES-LINK format is unique to ESOTERIC and is not compatible

with the HDMI specification. Do not connect the ES-LINK connec-

tor to an HDMI connector on a device made by another company.

Precautions for use

7

English

Network connections

a NAS (network-attached storage)

Use to store audio files.

Operation as a UPnP server is necessary to use it as a media

server.

Instead of using an NAS, audio files can also be put on a USB

flash drive or other USB storage device and that device con-

nected to a USB DRIVE port on this unit. Then, those files can

be played back using the media server function of the N-01XD

(page10).

b Wi-Fi™ router

Use Wi-Fi to connect the tablet or smartphone to this unit and

the NAS.

c Tablet/smartphone

Install the app to control this unit.

d N-01XD

This unit.

ATTENTION

By default, the ETHERNET port LED (LanLED>) setting is OFF

(page19).

a b

c

d

NAS Wi-Fi™ router

Tablet/smartphone

N-01XD

LAN cable

Connection example

To Internet

o An Internet connection is necessary to

install the app on a tablet or smartphone,

to update this unit’s NET firmware and to

use Internet radio, for example.

8

Connections

V

Precautions when making connections

o After completing all other connections, plug the power plug into a power outlet.

o Read the owner’s manuals of all devices that will be connected, and follow their instructions.

If the clock generator has

two or more outputs, it can

also be connected directly to

each device. Use the connec-

tion method that provides

the preferable sound quality.

RL

Stereo amplifier

Computer

RCA cables

XLR cables

USB cable

Included

power cord

RCA coaxial cable

BNC coaxial cable

Equipment

with digital

audio output

Equipment

with digital

audio output

Equipment

with digital

audio output

Equipment

with digital

audio output

(P-05X, etc.)

Device that outputs

clock signal

(G-01X, G-02X etc.)

DIGITAL OUT

(COAXIAL)

DIGITAL OUT

(XLR)

DIGITAL OUT

(ES-LINK)

DIGITAL OUT

(OPTICAL)

10MHz OUT

Audio input

(LINE IN, etc.)

Optical digital cable

USB flash drive

Make this connection when

using this unit as a USB DAC.

XLR digital cable

HDMI cables

c

Wall outlet

Connect using a set

of only one type.

The polarity of the XLR connectors

can be set so that either 2 or 3 is

HOT (page17).

9

English

A Analog audio output (LINE OUT) connectors

These output 2-channel analog audio. Connect the XLR or RCA

connectors to an amplifier.

Use commercially-available cables for connections.

XLR/ESL-A: XLR cables

RCA: RCA cables

Connect this unit’s R connector to the R connector of the ampli-

fier, and its L connector to the L connector of the amplifier.

Change the analog output setting according to the con-

nector being used (page17).

o Analog audio output can be set to XLR (polarity HOT for pin2

or 3 ), RCA or ESLA (page17).

o When connecting this unit with an amplifier that has ES-LINK

Analog (ESL-A) connectors, we recommend connecting the

analog audio output (XLR/ESL-A) connectors on this unit

to the ES-LINK Analog (ESL-A) connectors on the amplifier

(page10).

B ETHERNET port

Use a LAN cable to connect to a network.

Use a commercially-available LAN cable for connection.

C USB port

Use to input digital audio from a computer. Connect it to a com-

puter’s USB port.

Use a commercially-available USB cable for connection.

o Before connecting, read pages13 to 14.

D USB DRIVE port

Connect USB flash drives that contain audio files here.

o To play audio files on a USB flash drive connected to a USB

DRIVE port, set the input source to NET and use an app for

playback (page10).

E CLOCK IN (10MHz) and OUT connectors

Use the CLOCK IN (10MHz) connector to input 10MHz clock syn-

chronization signals.

To use clock synchronization, connect the clock output con-

nector of the device outputting the clock signal to the CLOCK

IN (10MHz) connector on this unit. Then, set the external clock

(CLK>) setting to IN (page16).

When outputting clock from this unit, connect its CLOCK OUT

connector to the clock input connector on the digital audio

output device. Then, set the clock (CLK>) setting to OUT44 or

OUT48 (page16).

Use commercially-available BNC coaxial cables for

connections.

o BNC coaxial cables with 50Ω or 75Ω impedance can be used.

F SIGNAL GND grounding terminal

The audio quality might be improved by connecting this

grounding terminal to an amplifier or other device that is con-

nected to this unit.

o This is not a safety grounding terminal.

G Digital audio input (DIGITAL IN) connectors

Use to input digital audio signals.

They can be connected to the digital output connectors of a

digital audio device such as the P-05X.

ES-LINK: HDMI cables

o The ES-LINK format is unique to ESOTERIC and is not compat-

ible with the HDMI specification. Do not connect the ES-LINK

connector to an HDMI connector on a device made by

another company.

o We recommend using ES-LINK when connecting to a P-05X.

Use commercially-available cables for the following

connections.

OPTICAL: optical digital cable (TOS)

RCA: RCA coaxial digital cable

XLR: XLR digital cable

o They can receive signals with sampling frequencies of

32–192kHz and bit depths up to 24-bit.

H AC power inlet (~IN)

Connect the included AC power cord to this AC inlet.

After completing all other connections, plug the power plug

into a power outlet.

V

Use only a genuine ESOTERIC power cord. Use of

other power cords could result in fire or electric

shock.

V

Disconnect the power plug from the outlet if you

will not use the unit for a long time.

I SOFTWARE maintenance port

This is used for maintenance. Do not connect anything to this

port unless instructed to do so by our service department.

10

Connecting using ES-LINK Analog

ESL-A

Amplifier with ES-LINK

Analog (ESL-A) connectors

XLR audio cables

ES-LINK Analog

(ESL-A) connectors

Use XLR audio cables to connect the analog audio output (XLR/ESL-

A) connectors on this unit to an amplifier that has ES-LINK Analog

(ESL-A) connectors.

o Set this unit’s analog output (AOUT) to ESLA.

o You can also connect using XLR or RCA connectors. Select the

connection type that provides the audio quality you prefer.

ES-LINK Analog overview

Using a current transmission method that utilizes the high-perfor-

mance of an HCLD buffer circuit, which boasts the ability to supply

strong current at high speed, the effects of impedance on the signal

path are suppressed and transmitting signals purely and powerfully is

possible.

o Ordinary balanced cables (with XLR connectors) are used for

connection. These connectors can only be used with compatible

devices, however, because the transmission format is unique.

Connections (continued) Downloading the remote app

To use the ETHERNET port or USB drive (DRIVE and ) ports, you

must also use a tablet or smartphone that has the dedicated app

(free) installed and connect it to the same network as the unit.

By installing the app on a tablet or smartphone, you can use it over a

wireless network to operate the unit.

o You can download and use the app for free.

Finding the tablet/smartphone app

Search for “ESOTERIC Sound Stream” in the App Store or Google Play

Store.

Playing audio files on a USB flash drive connected

to a USB DRIVE port

1) Put audio files on the USB flash drive or other USB storage device

and connect it to a USB DRIVE port.

2) Follow the procedures in “Getting started” of the ESOTERIC Sound

Stream User’s Manual to open the Setup menu.

3) In the Music Player section, select ESOTERIC N-01XD.

4) Select Music Library, and then select ESOTERIC N-01XD USB Music

Server.

o Refreshing the music library could take several minutes if it has

many audio files.

This completes the preparation for playing music files on a USB flash

drive connected to a USB DRIVE port.

Refer to the ESOTERIC Sound Stream User’s Manual to prepare play-

lists and play audio files.

NOTE

Network module firmware is updated through ESOTERIC Sound

Stream. We recommend that you regularly select this unit in ESOTERIC

Sound Stream, and update it with the latest firmware.

A pop-up window recommending a firmware update will appear if

one is available.

11

English

Names and functions of parts

A POWER button

Press to turn the unit on and off.

When the unit is on, the ring around the button lights.

When the unit is off, it is unlit.

When not using the unit, turn it off.

B CLOCK indicator

This shows the clock synchronization status.

This indicator blinks during clock synchronization and lights

when synchronization completes.

C USB drive port ( )

Connect USB flash drives that contain audio files here.

o To play audio files on a USB flash drive connected to a USB

DRIVE port, set the input source to NET and use an app for

playback (page10).

D Remote control signal receiver

This receives signals from the remote control. When using the

remote control, point the end of it toward this receiver panel.

o This product does not include a remote control.

o The dimmer of this unit can be adjusted using a remote control

included with another ESOTERIC product.

E Display

This shows various information, including the sampling frequency

of the input source.

F INPUT button

Press to change the digital input. Select a connector that has a

digital device connected. If no digital signal is being input, the

display will blink.

G MENU button

Press to enter setting mode.

H Setting adjustment (l/;) buttons

Use to change parameters when in setting mode.

When NET is selected, these can be used to play and skip tracks

in the playlist.

o You cannot change the volume with this unit.

12

Press the INPUT button repeatedly to cycle through the following input

sources.

ESLINK XLR RCA1 RCA2

NET USB OPT

(USB input

for computers)

(optical

digital input)

o If the input signal is not a digital audio signal or uses an audio sig-

nal format that is not supported by this unit (such as Dolby Digital

or DTS) “- - -” appears in place of the sampling frequency. Set the

digital output of the connected equipment to PCM audio output.

o To play audio files on a USB flash drive connected to a USB DRIVE

port, set the input source to NET and use an app for playback.

ATTENTION

When the network input circuit power supply setting (NETin>) is OFF,

NET will not be shown (page19).

Changing the input source

MQA (Master Quality Authenticated)

MQA is an award-winning British technology that delivers the sound

of the original master recording. The master MQA file is fully authenti-

cated and is small enough to stream or download.

Visit mqa.co.uk for more information.

The N-01XD includes MQA technology, which enables you to play

back MQA audio files and streams, delivering the sound of the origi-

nal master recording.

‘MQA’ or ‘MQA.’ indicates that the product is decoding and playing

an MQA stream or file, and denotes provenance to ensure that the

sound is identical to that of the source material. “MQA.” indicates it is

playing an MQA Studio file, which has either been approved in the

studio by the artist/producer or has been verified by the copyright

owner.

13

English

Using the USB DAC function

IMPORTANT NOTICE

You must install the dedicated driver software before connecting this

unit with a computer using a USB cable.

If you connect the unit to the computer by USB before installing the

driver, it will not function properly.

Depending on the composition of the computer hardware and

software, operation might not be possible even with the above oper-

ating systems.

Note about transmission modes

The sampling frequencies that can be transmitted are 44.1kHz,

48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz, 352.8kHz and 384kHz.

2.8MHz, 5.6MHz, 11.2MHz and 22.5MHz DSD are also supported.

o 22.5MHz DSD is only supported with DSD Native playback. It is not

supported with DoP (DSD Audio over PCM Frames) playback.

When connected correctly, you will be able to select “ESOTERIC USB

AUDIO DEVICE” as the audio output for the operating system.

Audio data sent from the computer will be processed using this unit’s

clock during data transmission, enabling reduction of jitter.

Downloading playback application

ESOTERIC HR Audio Player

You can use ESOTERIC HR Audio Player to play audio files on a computer.

Please download this free application from the following URL.

https://www.esoteric.jp/en/product/hr_audio_player/download

ESOTERIC HR Audio Player is a software audio player for Windows and

Mac that supports high-quality playback of high-resolution audio

sources. You can use it to enjoy the high-quality playback of high-

resolution audio sources, including DSD, without needing to make

complicated settings.

ESOTERIC HR Audio Player setting note

To play 22.5MHz DSD recordings with ESOTERIC HR Audio Player,

open the Configure window and set the “Decode mode” to “DSD

Native.”

To play formats other than 22.5MHz DSD, you can set this to either

“DSD over PCM” or “DSD Native” as you like.

For details, see “Selecting DSD decoding mode” in the ESOTERIC HR

Audio Player Owner’s Manual.

Supported operating systems

This unit can be connected by USB and used with a computer run-

ning one of the following operating systems.

Operation with other operating systems cannot be assured (as of

November 2019).

When using Mac

OS X Lion (10.7)

OS X Mountain Lion (10.8)

OS X Mavericks (10.9)

OS X Yosemite (10.10)

OS X El Capitan (10.11)

macOS Sierra (10.12)

macOS High Sierra (10.13)

macOS Mojave (10.14)

macOS Catalina (10.15)

When using Windows

Windows 7 (32/64-bit)

Windows 8 (32/64-bit)

Windows 8.1 (32/64-bit)

Windows 10 (32/64-bit)

Installing the driver

When using Mac

This unit can be operated with the standard OS driver, so there is no

need to install a driver.

When using Windows

To use this unit for playback of files on a computer, install the dedi-

cated driver on the computer.

Installing the driver on a computer

Install the dedicated driver software on the computer after down-

loading it from the following URL.

For detailed instructions about installing the driver, please also see

the following URL.

https://www.esoteric.jp/en/product/n-01xd/download

14

Playing audio files

1 Connect this unit to the computer using a USB

cable.

Use a commercially-available USB cable with a connector that

matches that of this unit.

USB cable

2 Turn the computer on.

Confirm that the operating system has started properly.

3 Press the POWER button to turn the unit on.

4 Press the INPUT button repeatedly to select

USB (page12).

5 Start playback of an audio le on the computer.

For better audio quality, set the computer volume to its maxi-

mum and adjust the volume of the amplifier connected to this

unit. Set the amplifier volume to the minimum when you start

playback and gradually increase it.

o The computer cannot be used to control this unit, nor can this

unit be used to control the computer.

o This unit cannot transmit audio files to the computer by USB.

o Do not do any of the following when playing back audio files over

the USB connection. Doing so could cause the computer to mal-

function. Always quit the audio playback software before conducting

any of these operations.

o Unplug the USB cable

o Turn this unit off

o Change the input

o Computer operation sounds will also be transmitted when play-

ing back audio files over the USB connection. To avoid outputting

these sounds, make the necessary settings on your computer.

o If you start the audio playback software before connecting this

unit with the computer or before setting the input to USB, audio

files might not play back properly. If this occurs, restart the audio

playback software or restart the computer.

Using the USB DAC function (continued)

15

English

Setting mode

3 Use the setting adjustment (l/;) buttons to

change the settings.

To change multiple items, repeat steps

2

and

3

.

4 Press the INPUT button to end setting mode.

Setting mode will also end and the ordinary display will reappear

if nothing is done for ten seconds.

o Settings are retained even if the power plug is disconnected.

The settings for this unit are divided into three groups: Settings1,

Settings2 and Settings3.

The Settings1, Settings2 or Settings3 group will be shown depend-

ing on how the MENU button is pressed.

1

4

2

3

Changing settings

1 When stopped or during playback, press the

MENU button.

Settings1 will be shown.

To show Settings2, press the MENU button again for at least two

seconds while Settings1 is shown.

To show Settings3, press the MENU button again for at least two

seconds while Settings2 is shown.

2 Press the MENU button repeatedly to select the

item to change.

Each time you press the MENU button, the item shown on the

display changes as follows.

Settings 1 Settings 2 Settings 3

UPC>

c

CLK>

c

PCMG>

c

AOUT>

c

DIMMER>

c

DPaOFF>

c

APS>

PCMM>

c

DSDF>

c

LanLED>

c

NETin>

c

REMOTE>

AUD UPDATE>

o If you do nothing for ten or more seconds, setting mode will

end and ordinary display will resume.

However, setting mode will not end when Settings 3 AUD_

UPDATE is in use.

o Depending on the selected source and operation status,

some items might not appear.

16

Settings 1

PCM signal upconversion setting

UPC>***

When PCM signals are being input, they can be upconverted or con-

verted to DSD signals.

o By default, the setting is ORG.

o This setting can be made for each input.

ORG

Upconversion will not occur.

o The input signal is sent as is to the D/A converter without

being upconverted.

2Fs

When PCM signals with frequencies of less than 88.2kHz are

input, they are upconverted before being converted from digital

to analog.

4Fs

When PCM signals with frequencies of less than 176.4kHz are

input, they are upconverted before being converted from digital

to analog.

8Fs

When PCM signals with frequencies of less than 352.8kHz are

input, they are upconverted before being converted from digital

to analog.

16Fs

When PCM signals with frequencies of less than 705.6kHz are

input, they are upconverted before being converted from digital

to analog.

DSD

Signals are converted to DSD before being converted from digital

to analog.

Clock setting

CLK>***

Use this to set synchronization with an external clock or clock output

to an audio source device that supports clock.

o By default, the setting is OFF.

o Set this to OFF when connected to a source device, other than

NET or USB input, that does not support clock synchronization.

o When input is USB or NET, OUT44 and OUT48 cannot be selected.

OFF

Clock synchronization is not used. The unit will operate with the

clock of the input digital signal.

The built-in oscillator will be used with NET and USB input.

The CLOCK indicator lights green.

IN

In this mode, the unit is synchronized with the 10MHz clock sig-

nal input through its CLOCK IN (10MHz) connector from a clock

generator.

The CLOCK indicator lights. The CLOCK indicator blinks when in

the process of synchronizing or unable to synchronize.

o The clock frequency that can be input is 10MHz. The input

audio signal and the input clock signal must be synchronized.

o Be aware that during music playback, if the clock generator

is turned off or the BNC coaxial cable that is supplying the

10MHz clock signal is disconnected, causing the clock signal to

stop, a loud noise could be emitted from the speakers.

OUT44

44.1kHz is output from the CLOCK OUT connector.

OUT48

48kHz is output from the CLOCK OUT connector.

17

English

PCM output gain setting

PCMG>***

Use this to set the gain for PCM signal playback. This can be used to

reduce the volume difference between PCM and DSD signal playback.

Set it as necessary.

o By default, USB and NET are set to LOW and other inputs are set to

FULL.

o This setting can be made for each input.

FULL

The gain is not adjusted.

LOW

The output level of PCM signals during full scale 0dB playback and

the output level of DSD signals during 0dB playback are the same.

Use when the volume of PCM signals during playback seem loud

compared to DSD signals.

Analog output setting

AOUT>***

Use this to select the analog output connector to be used.

o By default, the setting is XLR2.

XLR2

Analog audio signals are output through the XLR connectors with

pin 2 HOT.

XLR3

Analog audio signals are output through the XLR connectors with

pin 3 HOT.

RCA

Analog audio signals are output through the RCA connectors.

ESLA

Analog audio signals are output as ES-LINK Analog (ESL-A)

through the XLR connectors.

o These connections use ordinary XLR cables, but the signals are

transmitted in a unique format, so this setting should only be

used with compatible devices.

o See page10 for more about ES-LINK Analog (ESL-A).

Dimmer setting

DIMMER>***

Use this to adjust the brightness of the unit’s display.

By default, the setting is 2.

DIMMER>3

c

DIMMER>2 (normal brightness)

c

DIMMER>1

c

DIMMER>0 (off)

o Even when set to DIMMER>1 or DIMMER>0, setting menus and

error messages will be shown with normal brightness (DIMMER>2).

Automatic display darkening setting

DPaOFF>***

Use this to set the display to darken automatically.

o By default, the setting is ON.

o If the OEL display is left on with the same indication for a long time,

brightness irregularities can occur. For this reason, we recommend

that you set the automatic display darkening function to ON.

ON

If no operation is conducted for ten minutes, the display automati-

cally turns off.

OFF

The display will not turn off automatically.

o If no operation is conducted for ten minutes, the display will

dim to DIMMER>1 brightness to protect it from excessive wear.

18

D/A converter operation setting

PCMM>***

The D/A converter operation mode used during PCM playback can

be set to three types: M1, M2 or M3.

This changes the ΔΣ modulator operation frequency and randomiza-

tion algorithm used to absorb hardware error.

M1 is the ESOTERIC reference mode.

The operation frequency of the ΔΣ modulator becomes progressively

lower in order from M1 to M2 to M3.

The replacement amount of the randomization algorithm increases

progressively in order from M1 to M2 to M3.

Select the sound setting you prefer.

o By default, the setting is M1.

DSD filter setting

DSDF>***

Use to set the digital filter during DSD playback.

Set it as desired.

o By default, the setting is OFF.

OFF

No digital filter is used.

F1, F2, F3

A digital filter is used. F1, F2 and F3 are digital filters with different

frequency responses. The cutoff frequency becomes progressively

lower from F1 to F2 to F3.

Settings 2

Automatic power saving setting

APS>***

If there is no input from the selected input source for the set time, the

power will turn off automatically.

o By default, the setting is 30m.

o The input sources that are not selected have no effect on auto-

matic power saving.

30m

30 minutes

60m

60 minutes

90m

90 minutes

120m

120 minutes

OFF

The automatic power saving function is disabled.

Settings 1 (continued)

19

English

ETHERNET port LED setting

LanLED>***

Use to set the ETHERNET port LED. When set to OFF, the ETHERNET

port LED will not light, reducing the impact on audio quality.

o By default, the setting is OFF.

o Even when set to OFF, the LED will blink immediately after a LAN

cable is connected and while the unit is initializing after being

turned on (while “WAIT…” displayed).

OFF

The ETHERNET port LED stays unlit.

ON

Lighting and blinking of the ETHERNET port LED are enabled.

Network input circuit power supply

setting

NETin>***

Use to turn the network input circuit power supply on and off.

o By default, the setting is ON.

ON

This turns the network input circuit power supply on and plays

audio files from the network.

OFF

This turns the network input circuit power supply off, stopping

operation of the network input circuit.

NET will not be shown as an input source option (page12).

Remote control operation setting

REMOTE>***

Use this to set signal reception from ESOTERIC remote controls included

with the P-05X and other products.

By default, the setting is OFF.

o Regardless of this setting, remote control DIMMER buttons will

function.

o Set this to OFF when you are using an ESOTERIC amplifier. If set to

ON, the amplifier will be operated at the same time.

OFF

This disables control of this product using the buttons on the remote

control.

ON

This enables control of this product using the buttons for amplifier

control on remote controls.

The following table shows the correspondence between remote

control and unit buttons.

Remote control N-01XD

SETUP button MENU button

INPUT button INPUT button

VOLUME (+/−) buttons

Setting adjustment (l/;) buttons

20

Troubleshooting

If you experience a problem with this product, please take a moment

to review the following information before requesting service.

Moreover, the problem might be caused by something other than

this unit. Please also check the operation of the connected units.

If this product still does not operate correctly, contact the retailer

where you purchased it.

General

The unit does not turn on.

e Insert the power plug into an outlet.

e Check the connection of the power cord to this unit.

e Confirm that power is being supplied to the outlet to which the

power cord is connected by, for example, connecting another

device to it.

The unit automatically turns off.

e This is because the automatic power saving function turned

the unit off.

Press the POWER button on the main unit to turn it on.

Change the automatic power saving setting if necessary

(page18).

The unit does not respond when buttons are pressed.

e Multiple button presses without pause can cause the unit to

stop responding. After pressing a button, wait momentarily for

the unit to respond.

There is noise.

e Place the unit as far away as possible from TVs and other devices

that have strong magnetism.

No sound is output from the speakers. The sound is distorted.

e Check the connections with the amp and the speakers.

e Adjust the volume of the amplifier and other devices.

e No sound is output when playback is paused. Use the app to

resume ordinary playback.

e Check the analog output setting (page17).

Settings 3

Audio program update setting

AUD_UPDATE

Use to update the audio signal processing program of the unit.

See the explanation included with the update program for details

about how to update.

21

English

Clock sync

The CLOCK indicator does not stop blinking.

e Set CLK> to OFF when not using clock sync.

e A clock signal to which the unit cannot synchronize might be

being input. Check the connection of the CLOCK IN (10MHz)

connector and the settings of the connected device.

A cyclical noise is being output.

e If a cyclical noise is being output when the unit is in clock sync

mode, the connected device might not be in clock sync mode.

Check the connection of the CLOCK IN (10MHz) connector and

the clock synchronization setting of the connected device.

An audio file cannot be played back (correctly).

e Different media servers (NAS) support different types of files.

Check the specifications of the media server (NAS), too.

The sound breaks up during playback.

e If files that use lossy compression, including MP3s, and files at

44.1kHz and other low bit rates play back normally, but the

sounds of files at 384kHz and other high bit rates as well as

FLAC and other files that use lossless compression break up,

the ETHERNET speed might be too slow.

The audio data is transmitted from the NAS through the router.

For this reason, using LAN cables to connect the NAS to the

router and the router to this unit is preferable.

USB connections with a computer

Computer does not recognize this unit.

e See page 13 for information about supported operating

systems. Operation with unsupported operating systems is not

guaranteed.

There is noise.

e Starting other applications during playback of an audio file

may interrupt playback or cause noise. Do not start other appli-

cations during playback.

e When the unit is connected to a computer via a USB hub, for

example, noise might be heard. If this occurs, connect the unit

directly to the computer.

Audio files cannot be played back.

e Connect the computer with this unit and switch to USB before

starting the audio playback software and audio file playback.

Audio data might not play back correctly if you connect this

unit with the computer or change its input to USB after start-

ing the audio playback software.

Since this unit uses a microcontroller, external noise and other

interference can cause the unit to malfunction. If this occurs,

turn the unit off and wait about one minute before restarting

operation from the beginning.

Note about condensation

If this unit is brought from a cold outdoor environment into a

warm room, or the heater has just been turned on in the room

where it is located, for example, condensation might occur, result-

ing in improper operation. If this occurs, leave the unit on and wait

1–2 hours. This should enable normal playback.

Page is loading ...

Esoteric N-01XD Owner's manual

Esoteric N-01XD Owner's manual

in other languages

Related papers

Other documents