Chrysler 2012 Town & Country Owner's manual

Town & Country

Chrysler Group LLC

O W N E R ’ S M A N U A L

   

2012 Town & Country

12Y531-126-AA First Edition Printed in U.S.A.

903751 T&C OM cover.indd 1 3/18/11 7:22 AM

VEHICLES SOLD IN CANADA

With respect to any Vehicles Sold in Canada, the name Chrysler

Group LLC shall be deemed to be deleted and the name Chrysler

Canada Inc. used in substitution therefore.

DRIVING AND ALCOHOL

Drunken driving is one of the most frequent causes of accidents.

Your driving ability can be seriously impaired with blood alcohol

levels far below the legal minimum. If you are drinking, don’t drive.

Ride with a designated non-drinking driver, call a cab, a friend, or use

public transportation.

WARNING!

Driving after drinking can lead to an accident. Your percep-

tions are less sharp, your reflexes are slower, and your judg-

ment is impaired when you have been drinking. Never drink

and then drive.

This manual illustrates and describes the operation of features and

equipment that are either standard or optional on this vehicle. This

manual may also include a description of features and equipment

that are no longer available or were not ordered on this vehicle.

Please disregard any features and equipment described in this

manual that are not on this vehicle.

Chrysler Group LLC reserves the right to make changes in design

and specifications, and/or make additions to or improvements to its

products without imposing any obligation upon itself to install them

on products previously manufactured.

TABLE OF CONTENTS

SECTION PAGE

1

INTRODUCTION

............................................................3

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

..............................9

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

............................ 109

4

UNDERSTANDING YOUR INSTRUMENT PANEL

..................................283

5

STARTING AND OPERATING

................................................421

6

WHAT TO DO IN EMERGENCIES

............................................. 519

7

MAINTAINING YOUR VEHICLE

..............................................551

8

MAINTENANCE SCHEDULES

.................................................603

9

IF YOU NEED CONSUMER ASSISTANCE

........................................ 619

10

INDEX

...................................................................629

1

2

3

4

5

6

7

8

9

10

INTRODUCTION

CONTENTS

䡵 Introduction ........................... 4

䡵 How To Use This Manual .................. 4

䡵 Warnings And Cautions ................... 6

䡵 Vehicle Identification Number .............. 6

䡵 Vehicle Modifications/Alterations ............ 7

1

INTRODUCTION

Congratulations on selecting your new Chrysler Group

LLC vehicle. Be assured that it represents precision

workmanship, distinctive styling, and high quality - all

essentials that are traditional to our vehicles.

This Owner’s Manual has been prepared with the assis-

tance of service and engineering specialists to acquaint

you with the operation and maintenance of your vehicle.

It is supplemented by Warranty Information, and various

customer-oriented documents. Please take the time to

read these publications carefully. Following the instruc-

tions and recommendations in this manual will help

assure safe and enjoyable operation of your vehicle.

NOTE: After reviewing the owner information, it

should be stored in the vehicle for convenient referenc-

ing and remain with the vehicle when sold.

When it comes to service, remember that your authorized

dealer knows your vehicle best, has factory-trained tech-

nicians and genuine MOPAR威 parts, and cares about

your satisfaction.

HOW TO USE THIS MANUAL

Consult the Table of Contents to determine which section

contains the information you desire.

Since the specification of your vehicle depends on the

items of equipment ordered, certain descriptions and

illustrations may differ from your vehicle’s equipment.

The detailed index at the back of this Owner’s Manual

contains a complete listing of all subjects.

Consult the following table for a description of the

symbols that may be used on your vehicle or throughout

this Owner’s Manual:

4 INTRODUCTION

INTRODUCTION 5

WARNINGS AND CAUTIONS

This Owner’s Manual contains WARNINGS against op-

erating procedures that could result in a collision or

bodily injury. It also contains CAUTIONS against proce-

dures that could result in damage to your vehicle. If you

do not read this entire manual, you may miss important

information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the

left front corner of the instrument panel, visible through

the windshield. This number also appears stamped on

the right sliding door sill under the sill moulding and

printed on the Automobile Information Disclosure Label

affixed to a window on your vehicle, the vehicle regis-

tration and title.

Vehicle Identification Number

6 INTRODUCTION

NOTE: It is illegal to remove or alter the VIN.

VEHICLE MODIFICATIONS/ALTERATIONS

WARNING!

Any modifications or alterations to this vehicle could

seriously affect its roadworthiness and safety and

may lead to an accident resulting in serious injury or

death.

Stamped VIN Location

1

INTRODUCTION 7

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

CONTENTS

䡵 A Word About Your Keys ................. 12

▫ Wireless Ignition Node (WIN) ............ 12

䡵 Sentry Key威 .......................... 15

▫ Replacement Keys ..................... 16

䡵 Vehicle Security Alarm — If Equipped ........ 17

▫ Rearming Of The System ................ 17

䡵 Illuminated Entry — If Equipped ........... 20

䡵 Remote Keyless Entry (RKE) — If Equipped . . . 20

▫ Using The RKE Transmitter .............. 21

䡵 Remote Starting System — If Equipped ....... 30

▫ How To Use Remote Start ............... 30

䡵 Door Locks ........................... 34

▫ Manual Door Locks ................... 34

▫ Power Door Locks — If Equipped ......... 36

䡵 Keyless Enter-N-Go ..................... 37

䡵 Windows ............................ 41

▫ Power Vent Windows — If Equipped ....... 41

▫ Power Windows ...................... 42

2

䡵 Sliding Side Door ...................... 46

▫ Power Sliding Side Door — If Equipped ..... 47

▫ Sliding Side Door Child Protection Lock ..... 51

䡵 Liftgate ............................. 53

▫ Power Liftgate — If Equipped ............ 54

䡵 Occupant Restraints ..................... 57

▫ Lap/Shoulder Belts .................... 61

▫ Seat Belts In Passenger Seating Positions ..... 67

▫ Automatic Locking Retractor Mode (ALR) —

If Equipped ......................... 68

▫ Energy Management Feature ............. 69

▫ Seat Belt Pretensioners ................. 69

▫ Supplemental Active Head Restraints

(AHR) — If Equipped .................. 70

▫ Enhanced Seat Belt Use Reminder System

(BeltAlert威) ......................... 74

▫ Seat Belt Lock Out .................... 75

▫ Seat Belts And Pregnant Women .......... 75

▫ Seat Belt Extender ..................... 75

▫ Supplemental Restraint System (SRS) — Air

Bags .............................. 75

▫ Air Bag System Components ............. 77

▫ Advanced Front Air Bag Features .......... 78

▫ Air Bag Deployment Sensors And Controls . . . 81

▫ Event Data Recorder (EDR) .............. 88

▫ Child Restraints ...................... 89

10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

䡵 Commercial Cargo Vehicles (No Factory

Installed Rear Seats) — If Equipped ......... 100

▫ Restraining Infants And Small Children In

Commercial Cargo Vehicles ............. 101

䡵 Engine Break-In Recommendations ......... 103

䡵 Safety Tips .......................... 104

▫ Transporting Passengers ............... 104

▫ Exhaust Gas ........................ 104

▫ Safety Checks You Should Make Inside The

Vehicle ............................ 105

▫ Periodic Safety Checks You Should Make

Outside The Vehicle .................. 107

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11

A WORD ABOUT YOUR KEYS

Your vehicle uses a keyless ignition system. This system

consists of a Key Fob with Remote Keyless Entry (RKE)

transmitter and a Wireless Ignition Node (WIN) with

integral ignition switch. You can insert the Key Fob into

the ignition switch with either side up.

Keyless Enter-N-Go Feature

This vehicle may be equipped with the Keyless Enter-

N-Go feature, refer to “Starting Procedures” in “Starting

And Operating” for further information.

Wireless Ignition Node (WIN)

The Wireless Ignition Node (WIN) operates similarly to

an ignition switch. It has four operating positions, three

with detents and one that is spring-loaded. The detent

positions are OFF, ACC, and ON/RUN. The START

position is a spring-loaded momentary contact position.

When released from the START position, the switch

automatically returns to the ON/RUN position.

1 — OFF

2 — ACCESSORY

3 — ON/RUN

4 — START

12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Key Fob

The Key Fob operates the ignition switch. Insert the

square end of the key fob into the ignition switch located

on the instrument panel and rotate to the desired posi-

tion. It also contains the Remote Keyless Entry (RKE)

transmitter and an emergency key, which stores in the

rear of the Key Fob.

The emergency key allows for entry into the vehicle

should the battery in the vehicle or the RKE transmitter

go dead. The emergency key is also for locking the lower

glove compartment. You can keep the emergency key

with you when valet parking.

To remove the emergency key, slide the mechanical latch

at the top of the Key Fob sideways with your thumb and

then pull the key out with your other hand.

NOTE: You can insert the double-sided emergency key

into the lock cylinder with either side up.

Removing Key Fob From Ignition

Place the shift lever in PARK. Turn the Key Fob to the

OFF position and then remove the Key Fob.

Emergency Key Removal

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13

NOTE: Power window switches will also remain active

for up to 90 seconds after the ignition switch has been

turned to OFF, depending upon the accessory delay

setting. Opening the front door will cancel this feature.

WARNING!

•

When leaving the vehicle, always remove the key

fob from the ignition and lock your vehicle.

•

Never leave children alone in a vehicle, or with

access to an unlocked vehicle.

•

Allowing children to be in a vehicle unattended is

dangerous for a number of reasons. A child or

others could be seriously or fatally injured. Chil-

dren should be warned not to touch the parking

brake, brake pedal or the shift lever.

(Continued)

WARNING! (Continued)

•

Do not leave the key fob in or near the vehicle, and

do not leave Keyless Enter-N-Go in the ACC or

ON/RUN mode. A child could operate power win-

dows, other controls, or move the vehicle.

•

Do not leave children or animals inside parked

vehicles in hot weather. Interior heat build-up may

cause serious injury or death.

CAUTION!

An unlocked car is an invitation to thieves. Always

remove the Key Fob from the ignition and lock all

doors when leaving the vehicle unattended.

Key-In-Ignition Reminder

Opening the driver’s door when the Key Fob is in the

ignition and the ignition switch position is OFF or ACC,

a chime will sound to remind you to remove the key.

14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

NOTE: The Key-In-Ignition reminder only sounds

when the Key Fob is placed in the OFF or ACC ignition

position.

SENTRY KEY姞

The Sentry Key威 Immobilizer system prevents unauthor-

ized vehicle operation by disabling the engine. The

system does not need to be armed or activated. Operation

is automatic, regardless of whether the vehicle is locked

or unlocked.

The system uses Key Fob with factory-mated Remote

Keyless Entry (RKE) transmitter and Wireless Ignition

Node (WIN) to prevent unauthorized vehicle operation.

Therefore, only Key Fobs that are programmed to the

vehicle can be used to start and operate the vehicle. The

system will shut the engine off in two seconds if an

invalid Key Fob is used to start the engine.

After turning the ignition switch to the ON/RUN posi-

tion, the Vehicle Security Light will turn on for three

seconds for a bulb check. If the light remains on after the

bulb check, it indicates that there is a problem with the

electronics. In addition, if the light begins to flash after

the bulb check, it indicates that someone used an invalid

Key Fob to start the engine. Either of these conditions will

result in the engine being shut off after two seconds.

If the Vehicle Security Light turns on during normal

vehicle operation (vehicle running for longer than 10 sec-

onds), it indicates that there is a fault in the electronics.

Should this occur, have the vehicle serviced as soon as

possible by an authorized dealer.

CAUTION!

The Sentry Key威 Immobilizer system is not compat-

ible with some after-market remote starting systems.

Use of these systems may result in vehicle starting

problems and loss of security protection.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15

All of the Key Fobs provided with your new vehicle have

been programmed to the vehicle electronics.

Replacement Keys

NOTE: Only Key Fobs that are programmed to the

vehicle electronics can be used to start and operate the

vehicle. Once a Key Fob is programmed to a vehicle, it

cannot be reprogrammed to any other vehicle.

CAUTION!

Always remove the Key Fobs from the vehicle and

lock all doors when leaving the vehicle unattended.

At the time of purchase, the original owner is provided

with a four-digit Personal Identification Number (PIN).

Keep the PIN in a secure location. This number is

required for authorized dealer replacement of Key Fobs.

Duplication of Key Fobs may be performed at an autho-

rized dealer, this procedure consists of programming a

blank Key Fob to the vehicle electronics. A blank Key Fob

is one that has never been programmed.

NOTE: When having the Sentry Key威 Immobilizer

system serviced, bring all vehicle Key Fobs with you to

the authorized dealer.

Customer Key Programming

Programming Key Fobs or RKE transmitters may be

performed at an authorized dealer.

General Information

The Sentry Key威 system complies with FCC rules Part 15

and with RSS-210 of Industry Canada. Operation is

subject to the following conditions:

•

This device may not cause harmful interference.

16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

•

This device must accept any interference that may be

received, including interference that may cause unde-

sired operation.

VEHICLE SECURITY ALARM — IF EQUIPPED

The Vehicle Security Alarm monitors the vehicle doors

for unauthorized entry and the ignition switch for unau-

thorized operation. When the alarm is activated, the

interior switches for door locks, power sliding doors and

power liftgate are disabled. The Vehicle Security Alarm

provides both audible and visible signals, for the first

three minutes, the headlights will turn on, the park lamps

and/or turn signals will flash and Vehicle Security Light

will flash repeatedly and the horn will sound. For an

additional 15 minutes, only the headlights, park lamps

and/or turn signals and Vehicle Security Light will flash.

Rearming Of The System

The Vehicle Security Alarm will rearm itself after the 15

additional minutes of headlights and Vehicle Security

Light flashing, if the Vehicle Security Alarm has not been

disabled. If the condition which initiated the alarm is still

present, the Vehicle Security Alarm will ignore that

condition and monitor the remaining doors and ignition.

To Arm The System

Follow these steps to arm the Vehicle Security Alarm:

1. Remove the key from the ignition system (refer to

⬙Starting Procedures⬙ in ⬙Starting And Operating⬙ for

further information).

• For vehicles equipped with Keyless Enter-N-Go, make

sure the vehicle ignition system is ⬙OFF⬙.

• For vehicles not equipped with Keyless Enter-N-Go,

make sure the vehicle ignition system is ⬙OFF⬙ and the

key is physically removed from the ignition.

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17

2. Perform one of the following methods to lock the

vehicle:

• Press LOCK on the interior power door lock switch

with the driver and/or passenger door open.

• Press the LOCK button on the exterior Passive Entry

Door Handle with a valid Key Fob available in the same

exterior zone (refer to ⬙Keyless Enter-N-Go⬙ in ⬙Things To

Know Before Starting Your Vehicle⬙ for further informa-

tion).

• Press the LOCK button on the Remote Keyless Entry

(RKE) transmitter.

3. If any doors are open, close them.

To Disarm The System

The Vehicle Security Alarm can be disarmed using any of

the following methods:

•

Press the UNLOCK button on the Remote Keyless

Entry (RKE) transmitter.

•

Grasp the Passive Entry Unlock Door Handle (if

equipped, refer to ⬙Keyless Enter-N-Go⬙ in ⬙Things To

Know Before Starting Your Vehicle⬙ for further infor-

mation).

•

Cycle the vehicle ignition system out of the OFF

position.

•

For vehicles equipped with Keyless Enter-N-Go,

press the Keyless Enter-N-Go Start/Stop button

(requires at least one valid Key Fob in the vehicle).

•

For vehicles not equipped with Keyless Enter-N-Go,

insert a valid key into the ignition switch and turn

the key to the ON position.

18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Page is loading ...

Chrysler 2012 Town & Country Owner's manual

This manual is also suitable for

Chrysler 2012 Town & Country Owner's manual

Related papers