Lifetime 290038 Owner's manual

Brand: Lifetime

Model: 290038

Type: Owner's manual

TOOLS REQUIRED

TABLE OF CONTENTS

CONTACT LIFETIME CUSTOMER SERVICE:

Call: 1-800-225-3865

7:00 am–5:00 pm (Monday–Friday) MST

and 9:00 am–1:00 pm Saturday MST

QUESTIONS?

MODEL# AND PRODUCT ID

(you will need both when contacting us)

Model Number: 290038

Product ID:

• Before you start, prepare a level surface with the proper

Safety Zone (see page 12).

• 2+ people recommended for setup

Pour le français, voir la page 2. Para el español, ver la página 3.

ASSEMBLY INSTRUCTIONS

MODEL #60091

MODEL 290038

Save this instruction in the event that the manufacturer has

to be contacted for replacement parts.

For Customer Service in Mainland

Europe and the United Kingdom:

E-mail: [email protected]

Live Chat: www.lifetime.com

(click on “Ask An Expert” tab)

Video Instructions:

www.youtube.com/lifetimeproducts

10 FOOT SWING SET

(2, included)

1/2 in/po (≈13 mm)

(1)

3/16 in/po (≈5 mm)

9/16 in/po (≈14 mm)

(2)

(1)

(2, included)

7/32 in/po (≈6 mm)

(2)

Icon Legend...............................4

Warnings and Notices.................5

Safety Information.....................6

Safe Play Area...........................12

Swing Bar Assembly....................13

A-Frame Assembly....................17

Parts Identiﬁ er..........................i-iv

Final Assembly.........................24

Maintenance Instructions..........27

Registration...........................31

Warning Sticker........................32

Warranty..............................33

(1)

COPY

Page is loading ...

WARNINGS & NOTICES / AVERTISSEMENTS ET AVIS / ADVERTENCIAS Y AVISOS

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing

material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware

identiﬁ er and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the

risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

• If using a ladder during assembly, use extreme caution.

• Two capable adults are recommended for this operation.

• Be aware that parts can be damaged by overtightening the screws.

• All who participate in the assembly process should wear safety glasses throughout the assembly.

SAFETY INSTRUCTIONS

La mayoría de las lesiones ocurren a causa del mal uso y/o por no seguir las instrucciones. Tenga precaución al usar este producto.

A ﬁ n de garantizar la seguridad, no intente ensamblar este producto sin seguir cuidadosamente las instrucciones. Revise en toda la caja y dentro de

todos los materiales del empaque que estén las partes y/o material de instrucción adicional. Antes de comenzar el montaje, lea las instrucciones e

identiﬁ que las piezas utilizando el identiﬁ cador de herrajes y la lista de piezas en este documento. Un ensamblado adecuado y completo, el uso y la

supervisión son fundamentales para tener una operación adecuada y reducir el riesgo de accidentes o lesiones. Existe una alta probabilidad de sufrir

lesiones graves si este producto no se instala, no se le da mantenimiento y/o no se opera de manera adecuada.

NO SEGUIR ESTAS ADVERTENCIAS PUEDE RESULTAR EN LESIONES GRAVES O DAÑOS A LA PROPIEDAD Y ANULARÁ LA GARANTÍA.

El propietario debe asegurarse de que todos los jugadores conozcan y sigan estas reglas para el funcionamiento seguro del sistema.

• Si usa una escalera durante el ensamblado, extreme precauciones.

• Para esta actividad se recomienda contar con el apoyo de dos adultos en posibilidad de llevar a cabo dicha actividad.

• Tenga en cuenta que las piezas pueden dañarse si los tornillos se aprietan de más.

• Todas las personas que participen en el proceso de ensamblado deben usar anteojos de seguridad durante todo el ensamblado.

INSTRUCCIONES DE SEGURIDAD

La majorité des accidents résultent d’une mauvaise utilisation et/ou du fait de n’avoir pas suivi les consignes. Observez toutes précautions utiles pendant

l’utilisation de ce produit.

Pour assurer votre sécurité, ne tentez pas d’assembler cet article sans avoir lu et suivi toutes les consignes attentivement. Vériﬁ ez la totalité de la

boîte et l’intérieur de tous les matériaux d’emballage pour trouver toutes les pièces et/ou matériau contenant des consignes supplémentaires. Avant

de commencer le montage, identiﬁ ez toutes les pièces et tous les accessoires et faites-en l’inventaire en les comparant aux listes et identiﬁ cateurs

de pièces et accessoires contenus dans ce document. Un assemblage correct et complet, ainsi que l’utilisation et la supervision correctes sont des

conditions essentielles à la bonne direction et diminuent les risques d’accident ou de blessure. Une haute probabilité d’accident grave résulte de

mauvaises conditions d’installation, maintenance et/ou utilisation.

LE NON-RESPECT DE CES AVERTISSEMENTS PEUT RÉSULTER EN ACCIDENTS GRAVES OU DOMMAGES MATÉRIELS ET ANNULER LA GARANTIE.

Le propriétaire doit veiller à ce que tous les joueurs connaissent et suivent ces règles pour une exploitation sûre du système.

• Agissez avec la plus grande prudence si vous employez une échelle pour l’assemblage.

• Il est recommandé que cet assemblage soit exécuté par deux personnes adultes.

• Il est possible d’endommager les pièces en serrant les vis excessivement.

• Toutes les personnes qui participent à l’assemblage doivent porter des lunettes de sécurité tout le long de l’assemblage.

CONSIGNES DE SÉCURITÉ

**IMPORTANT SAFETY INFORMATION**

• Place the equipment on a level, well-drained ground, not less than 6.6 ft (2.0 m) from any struc-

ture or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical

wires

• Provide enough room so that children can use the equipment safely. For example, for structures

with multiple play activities, a slide should not exit in front of a swing.

• Separate active and quiet activities from each other. For example, locate sandboxes away from

swings or use a guardrail or barrier to separate the sandbox from the movement of the swings.

• Do not install home playground equipment over concrete, asphalt, packed earth, grass, carpet, or any

other hard surface. A fall onto a hard surface can result in serious injury to the equipment user (see page 7).

• To prevent serious injury, warn children that they must not use the equipment until properly installed.

• Create a site free of obstacles that could cause injuries – such as low overhanging tree branches,

overhead wires, tree stumps and/or roots, large rocks, bricks, and concrete.

• Choose a level location for the equipment. This can reduce the likelihood of the play set tipping

over and loose-ﬁ ll surfacing materials washing away during heavy rains.

• For any questions call our Customer Service Department at 1-800-225-3865 for more information.

• Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging.

• Do not install loose ﬁ ll surfacing over hard surfaces such as concrete or asphalt.

• Installations of rubber tiles or poured-in-place surfaces (other than loose-ﬁ ll materials) generally

require a professional and are not “do-it yourself” projects.

• Use Playground Surfacing Materials (other than loose-ﬁ ll material) which comply to the safety standard

ASTM F1292 Standard Speciﬁ cation for Impact Attenuation of Surfacing Materials within the Use Zone of

Playground Equipment.

INSTALLATION & GROUND PREPARATION INSTRUCTIONS

PLAYGROUND AND SURFACE MATERIALS INSTRUCTIONS

OPERATING INSTRUCTIONS

Observing the following instructions and warnings reduces the likelihood of serious or fatal injury:

• The maximum number of occupants that may safely use the entire play set including all

components is three with a maximum weight of 405 pounds (184 kg).

• On-site adult supervision should be provided for children of all ages.

• Instruct children not to walk close to, in front of, behind, or between moving items.

• Do not move the equipment while it is in use.

• Instruct children not to twist swing chains or ropes or loop them over the top support bar since this

may reduce the strength of the chain or rope.

• Instruct children to avoid swinging empty seats.

• Teach children to sit in the center of the swings with their full weight on the seats.

• Instruct children not to use the equipment in a manner other than intended.

• Instruct children not to get off the equipment while it is in motion.

• To prevent entanglement and strangulation, dress children appropriately using well-ﬁ tting shoes

and avoiding ponchos, scarves, jackets with neck drawstrings, helmets with straps, and other loose-

ﬁ tting clothing that is potentially hazardous while using equipment.

• Instruct children not to play when the equipment is wet.

• Instruct children not to attach items to the playground equipment that are not speciﬁ cally designed

for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables

and chain as they may cause a strangulation hazard.

PLEASE READ BEFORE BEGINNING ASSEMBLY:

*This information has been extracted from the CPSC publications “Playground Surfacing--Technical Information Guide” and

“Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to the: Ofﬁ ce of

Public Affairs, U.S. Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-

2772.

***This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire

samples produced by four manufacturers. It is recommended that persons seeking to install shredded tires as a protective surface

request test data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292.

CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS*

**The maximum fall height for this product is 108 in (274 cm).

We recommend using 9 in (23 cm) of Double Shredded Bark Mulch.**

5 ft 6 ft 7 ft 9 ft 10 ft 11 ft 12 ft

-- 6 in -- -- 9 in 12 in --

-- 6 in 9 in -- -- -- 12 in

6 in -- 9 in 12 in -- -- --

-- 6 in 9 in -- 12 in -- --

-- -- -- -- 6 in -- --

TABLE 1 — Depth of Surfacing Material Required Based on Fall Heights

Double Shredded Bark

Mulch

Wood Chips

Fine Sand

Fine Gravel

Shredded Tires***

(152 cm)

(183 cm) (213 cm)

(274 cm)

(305 cm) (335 cm) (366 cm)

(15 cm)

(23 cm) (30 cm)

(15 cm) (23 cm) (30 cm)

(30 cm)

(23 cm)(15 cm)

(15 cm)

(23 cm)

(30 cm)

(15 cm)

Select Protective Surfacing—One of the most important things you can

do to reduce the likelihood of serious head injuries is to install shock-

absorbing protective surfacing under and around your play equipment.

The protective surfacing should be applied to a depth that is suitable for

the equipment height in accordance with ASTM Speciﬁ cation F1292.

There are different types of surfacing to choose from; whichever product

you select, follow these guidelines:

Loose-Fill Materials—Maintain a minimum depth of 9 inches of looseﬁ ll

materials such as wood mulch/chips, engineered wood ﬁ ber (EWF), or

shredded/recycled rubber mulch for equipment up to 8 feet high; and

9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE:

An initial ﬁ ll level of 12 inches will compress to about a 9-inch depth of

surfacing over time. The surfacing will also compact, displace, and settle,

and should be periodically reﬁ lled to maintain at least a 9-inch depth.

Use a minimum of 6 inches of protective surfacing for play equipment

less than 4 feet in height. If maintained properly, this should be

adequate. (At depths less than 6 inches, the protective material is too

easily displaced or compacted.)

NOTE: Do not install home playground equipment over

concrete, asphalt, or any other hard surface. A fall onto a hard surface

can result in serious injury to the equipment user. Grass and dirt are not

considered protective surfacing because wear and environmental factors

can reduce their shock absorbing effectiveness. Carpeting and thin mats

are generally not adequate protective surfacing. Ground level equipment

– such as a sandbox, activity wall, playhouse or other equipment that has

no elevated play surface – does not need any protective surfacing.

Use containment, such as digging out around the perimeter and/or lining

the perimeter with landscape edging. Don’t forget to account for water

drainage.

Check and maintain the depth of the loose-ﬁ ll surfacing material. To

maintain the right amount of loose-ﬁ ll materials, mark the correct level

on play equipment support posts. That way you can easily see when to

replenish and/or redistribute the surfacing.

Do not install loose ﬁ ll surfacing over hard surfaces such as concrete or

asphalt.

Poured-In-Place Surfaces or Pre-Manufactured

Rubber Tiles—You may be interested in using surfacing other than loose-

ﬁ ll materials – like rubber tiles or poured-in-place surfaces.

Installations of these surfaces generally require a professional and are not

“do-it-yourself” projects.

Review surface speciﬁ cations before purchasing this type of surfacing.

Ask the installer/manufacturer for a report showing that the product has

been tested to the following safety standard: ASTM F1292 Standard

Speciﬁ cation for Impact Attenuation of Surfacing Materials within the

Use Zone of Playground Equipment. This report should show the speciﬁ c

height for which the surface is intended to protect against serious head

injury. This height should be equal to or greater than the fall height –

vertical distance between a designated play surface (elevated surface for

standing, sitting, or climbing) and the protective surfacing below – of your

play equipment.

Check the protective surfacing frequently for wear.

Placements—Proper placement and maintenance of protective surfacing

is essential. Be sure to:

Extend surfacing at least 6.6 feet (2 m) from the equipment in all

directions.

For to-fro swings, extend protective surfacing in front of and behind the

swing to a distance equal to twice the height of the top bar from which

the swing is suspended.

For tire swings, extend surfacing in a circle whose radius is equal to

the height of the suspending chain or rope, plus 6.6 feet (2 m) in all

directions.

Page is loading ...

33 feet (10 m)

36 feet (11,0 m)

6.6 feet

(2,0 m)

6.6 feet

(2,0 m)

18 feet (5,49 m)

ZONE DE SÉCURITÉ — Placez l’équipement à plus de 2,0 m (6.6 pi) de toute structure ou obstruction

telle qu’une clôture, un garage, une maison, des branches basses, des cordes à linge ou des ﬁls

électriques. Assurez-vous que l’espace libre devant et derrière les balançoires soit d’au moins deux fois

la hauteur de la barre de la balançoire. La surface d’impact doit couvrir l’aire de jeu recommandée au

complet. Veuillez vous référer à l’exemple ci-dessous.

Dimensions du Jeu:

13.6' (4,1 m) x 10.6' (3,2 m)

Aire de jeu recommandée:

33' (10 m) x 36' (11 m)

ZONA DE SEGURIDAD — Coloque el equipo a no menos de 2,0 m (6.6 pies) de cualquier estructura u

obstrucción como una cerca, una cochera, una casa, ramas que cuelgan, lazos para tender ropa o cables

eléctricos. Asegúrese de que el espacio libre enfrente y detrás de los columpios es de al menos el doble

de la altura de la barra de los columpios. El revestimiento superﬁcial de impacto necesita cubrir el área

entera de juego recomendada. Consulte al ejemplo a continuación.

Dimensiones del conjunto de juegos

13.6' (4,1 m) x 10.6' (3,2 m)

Área de juego recomendada

33' (10 m) x 36' (11 m)

SAFE PLAY AREA / ZONE DE SÉCURITÉ / ZONA DE SEGURIDAD

SAFETY ZONE —

Place the equipment no less than 6.6 ft. (2.0 m) from any structure or obstruction

such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. Make sure

the clearance in front of and behind the swings is at least twice the height of the swing bar. The impact

surfacing needs to cover the entire recommended play area. Refer to the example below.

Playset dimensions:

13.6' (4,1 m) x 10.6' (3,2 m)

Recommended play area:

33' (10 m) x 36' (11 m)

HARDWARE REQUIRED / ACCESSOIRES REQUIS / HERRAJE REQUERIDO

BFF

DZQ (x6)

PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS

TOOLS REQUIRED / OUTILS REQUIS / INSTRUMENTAL REQUERIDO

1/2 in/po (≈13 mm)

(2)

CONTENTS OF BOX 2 / CONTENU DE LA BOÎTE 2 / CONTENIDO DE LA CAJA 2

SWING BAR ASSEMBLY / ASSEMBLAGE DE LA BALANÇOIRE / ENSAMBLE DE LOS COLUMPIOS

EME (x2)

EMD (x2)

ASV (x2)

DZR (x4)

AAN (x4)

ARL (x2)

BKR (x1)

BKS (x2)

(1)

Hardware Bag / Sac d’accessoires / Bolsa de herraje

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN)

• Slide an Outside Swing Bar (BKS) into the Middle Swing Bar (BKR) as shown, and attach the swing bars together with the

hardware shown.

• Faites glisser une Barre de balançoire externe (BKS) dedans la Barre de balançoire intermédiaire (BKR) comme illustré,

et attachez les Barres à l’aide des accessoires illustrés.

• Deslice una Barra de columpio exterior (BKS) dentro de la Barra de columpio intermedia (BKR) como se muestra, y sujete

las dos con los elementos requeridos.

1.1

EMD (x2)

DZQ (x2)

4 1/2”

EME (x2)

ARL (x2)

• Slide the other Outside Swing Bar (BKS) into the other end of the Middle Swing Bar (BKR) as shown, and attach the swing bars

together with the hardware shown.

• Faites glisser l’autre Barre de balançoire externe (BKS) dedans l’autre extrémité de la Barre de balançoire intermédiaire (BKR)

comme illustré, et attachez les Barres de balançoire à l’aide des accessoires illustrés.

• Deslice la otra Barra de columpio exterior (BKS) dentro del extremo opuesto de la Barra de columpio intermedia (BKR) como se

muestra. Sujete las dos con los elementos requeridos.

BKR

BKS

EME

EMD

DZQ

EMD

EME

ARL

BKR

BKS

EME

EMD

EME

DZQ

EMD

ARL

• Only ﬁ nger tighten the

hardware in this step.

• Serrez les accessoires

à main seulement.

• Apriete los elementos

sólo con las manos en

este paso.

1.2

• Only ﬁ nger tighten the

hardware in this step.

• Serrez les accessoires

à main seulement.

• Apriete los elementos

sólo con las manos en

este paso.

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN)

1.3

• In order to seat the swing bar poles, strike each end of the swing bar very hard ﬁ ve to six times on a piece of scrap

wood or cardboard. After the swing bar poles have been seated, tighten the hardware from steps 1.1 and 1.2.

• Pour pouvoir asseoir les Sections du poteau, frappez bien fermement chaque extrémité du Poteau cinq à six

fois sur un morceau de bois ou de carton. Après avoir assis les Barres de balançoire, serrez les accessoires des

étapes 1,1 et 1,2.

• Para poder asentar los Postes, golpee fuertemente cada extremo cinco a seis veces en un pedazo de madera o

cartón. Después de haber asentado los Postes, apriete los elementos de los pasos 1,1 y 1,2.

• Do not hit your feet with the pole sections, as serious

injury could occur.

• Pour éviter des blessures graves, ne frappez pas vos pieds

avec les Sections du poteau.

• Cuide de no golpear sus pies con las secciones del Poste,

ya que podría sufrir graves lesiones.

BKS

BKR

BKS

• Tighten the hardware from steps 1.1 and 1.2

before continuing to the next step.

• Répétez étapes 1,1 – 1,2 pour tous les quatre

Ensembles du poteau avant de suivre à la

prochaine étape.

• Apriete los elementos de los pasos 1,1 – 1,2

antes de continuar al próximo paso.

WARNING

The Poles must be seated together! They must

be struck on a hard surface ﬁve to six times!

Failure to seat the Poles correctly could allow the

Poles to separate during use, which could lead

to serious personal injuries or property damage.

AVERTISSEMENT

Il est impératif emboîter bien les Sections du poteau ! Il faut

bien les frapper cinq à six fois sur une surface dure ! Sans

emboîter bien les Sections du poteau correctement, les

Sections peuvent séparer pendant l’usage et causer des

blessures graves et/ou dommage à la propiété.

ADVERTENCIA

¡Es imperativo asentar las secciones del poste!

Golpéelas en un pedazo de madera o cartón 5 a 6

veces. El incumplimiento de asentar las secciones

correctamente puede ocasionar la separación de las

secciones durante el juego, la cual puede ocasionar

en lesiones graves personales o daño a la propiedad.

1/2 in/po (≈13 mm)

(2)

(1)

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 1 (CONTINUED) / SECTION 1 (SUITE) / SECCIÓN 1 (CONTINUACIÓN)

AAN (x2)

1.4

• Attach the Swing Hardware to all of the brackets on the Swing Bar Assembly as shown.

• Attachez les accessoires à tous les supports sur le Montage de la barre de balançoire comme illustré.

• Sujete los elementos para el armado de las barras de columpio a todos los soportes del Conjunto de las barras de

columpio como se muestra.

1.5

• Insert the Round Caps (ASV) into the ends of the Swing Bar Assembly as shown.

• Insérez les Capuchons ronds (ASV) dedans les extrémités du Montage de la barre de balançoire comme illustré.

• Introduzca los Tapones redondos (ASV) dentro de los extremos del Conjunto de las barras de columpio como se

muestra.

DZQ (x4)

ASV (x2)

DZR (x4)

DZR

DZQ

AAN

DZQ

DZR

AAN

ASV

1/2 in/po (≈13 mm)

(2)

HARDWARE REQUIRED / ACCESSOIRES REQUIS / HERRAJE REQUERIDO

BFG

PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS

ADS (x8) BFB (x16) BFC (x16)

AOY (x1)

EEO (x2)

DXT (x4)

BTS (x4)

DSA (x4)

CONTENTS OF BOX 1 / CONTENU DE LA BOÎTE 1 / CONTENIDO DE LA CAJA 1

ALE (x4)

ALH (x4)

A-FRAME ASSEMBLY / ASSEMBLAGE DE LA CHARPENTE EN « A » / ENSAMBLE DEL ARMAZÓN EN «A»

Hardware Bag / Sac d’accessoires / Bolsa de herraje

PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS

TOOLS REQUIRED / OUTILS REQUIS / INSTRUMENTAL REQUERIDO

3/16 in/po (≈5 mm)

7/32 in/po (≈6 mm)

9/16 in/po (≈14 mm)

(1)

CONTENTS OF BOX 2 / CONTENU DE LA BOÎTE 2 / CONTENIDO DE LA CAJA 2

A-FRAME ASSEMBLY / ASSEMBLAGE DE LA CHARPENTE EN « A » / ENSAMBLE DEL ARMAZÓN EN «A»

ALF (x4)

BKN (x2)

BKM (x2)

BKO (x2)

BKQ (x2)

BKP (x2)

(1)

(2)

PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS

Remove This Section/ Enlevez Cette Section / Reitire Esta Sección

This page intentionally left blank

Cette page est intentionnellement laissée en blanc

Esta página ha sido dejada en blanco intencionalmente

PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS

Remove This Section / Enlevez Cette Section / Reitire Esta Sección

CONTENTS OF BOX 1 / CONTENU DE LA BOÎTE 1 / CONTENIDO DE LA CAJA 1

ALE (x4)

ALH (x4)

BKR (x1)

BKS (x2)

CONTENTS OF BOX 2 / CONTENU DE LA BOÎTE 2 / CONTENIDO DE LA CAJA 2

iii

PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS

Remove This Section/ Enlevez Cette Section / Reitire Esta Sección

BFGBFF

CONTENTS OF BOX 2 / CONTENU DE LA BOÎTE 2 / CONTENIDO DE LA CAJA 2

ALF (x4)

BKN (x2)

BKM (x2)

BKO (x2)

BKQ (x2)

BKP (x2)

BFH

Hardware Bag / Sac d’accessoires / Bolsa de herraje

PARTS IDENTIFIER / IDENTIFICATEUR DE PIÈCES / IDENTIFICADOR DE PIEZAS

Remove This Section / Enlevez Cette Section / Reitire Esta Sección

This page intentionally left blank

Cette page est intentionnellement laissée en blanc

Esta página ha sido dejada en blanco intencionalmente

Page is loading ...

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN)

2.2

• Align the hole in the Middle Pole (ALF) with the slot in the Bottom Pole (ALE) and slide the Bottom Pole into the

Middle Pole as shown. Insert a Screw (ADS) through the small hole in the Middle Pole and into the slot in the

Bottom Pole as shown.

• Alignez le trou dans la Section intermédiaire du poteau (ALF) avec l’encoche sur la Section inférieure du poteau (ALE),

et faites glisser la Section inférieure du poteau dedans la Section intermédiaire du poteau comme illustré.

Insérez une Vis à tête ronde (ADS) à travers le petit trous dans la Section intermédiaire du poteau et dedans

l’encoche sur la Section inférieure du poteau comme illustré.

• Alinee el agujero en el Poste intermedio (ALF) con la ranura en el Poste inferior (ALE) y deslice el Poste intermedio

sobre el Poste inferior. Introduzca un Tornillo de (ADS) a través del pequeño agujero en el Poste intermedio.

ADS (x7)

ALF

ALE

ADS

ALE

ALF

• The Screw should be ﬂ ush with the pole, but will spin freely once installed. Do not jam the poles together until

instructed.

• La Vis à tête ronde doit être à ras du Poteau, mais tournera librement une fois installée. N’emboîtez pas les Sections

de poteau jusqu’à plus tard.

• El Tornilla debe estar a ras con el Poste, mas girará libremente una vez instalado. No golpee las secciones del Poste

para asentarlas hasta que se le indique.

• Repeat steps 2.1 through 2.2 to assemble all four Pole Assemblies before moving to the next step.

• Répétez étapes 2,1 – 2,2 pour tous les quarte Ensembles du porteau avant de suivre à la prochaine

étape.

• Repita pasos 2,1 a 2,2 para armar los cuatro Conjuntos de poste antes de continuar con el paso

siguiente.

2.3

(1)

Page is loading ...

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN)

2.5

• Lay two Pole Assemblies on the ground with the holes on the poles oriented as shown.

• Posez deux Ensembles de poteaux sur la terre avec les trous sur les poteaux orientés comme illustré.

• Coloque los dos Conjuntos de poste en el suelo con los agujeros en los postes orientados como se muestra.

BFB (x4)

BFC (x4)

ALH

ALF

ALE

ALF

ALH

ALE

2.6

• Attach an Outside Bracket (BKO) and an Inside Bracket (with notches) (BKM) to the ends of two Top Poles (ALH) with the

hardware shown.

• Attachez bien un Support externe (BKO) et un Support interne (avec encoches) (BKM) aux extrémités des deux Sections

supérieures du poteau (ALH) à l’aide des accessoires requis.

• Sujete un Soporte exterior (BKO) y un Soporte interior (con muescas) (BKM) a los extremos de los dos Postes superiores

(ALH) con los elementos requeridos.

ALH

BKO

BKM

BFB

BFC

Notches

Encoches

Muescas

7/32 in/po (≈6 mm)

9/16 in/po (≈14 mm)

(1)

(2)

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 2 (CONTINUED) / SECTION 2 (SUITE) / SECCIÓN 2 (CONTINUACIÓN)

2.7

• Attach an A-Side Bracket (BKQ) to a Top Pole (ALH) by ﬁ nger tightening the hardware shown. Make sure the straight edge of

the A-Side Bracket is against the Outside Bracket (BKO) as shown. Only ﬁ nger tighten the hardware in this step.

• Attachez un Support latéral A (BKQ) aux Sections supérieures du poteau (ALH) comme illustré. Serrez les accessoires à la main

seulement. Vous assurez-vous d’orienter le bord droit du Support latéral A contre le Support externe (BKO) comme

illustré. Serrez les accessoires à la main seulement.

• Sujete el Soporte lateral A (BKQ) al Poste superior (ALH) por apretar sólo a mano los elementos requeridos. Asegure que el

borde derecho del Soporte lateral A está contra el Soporte exterior (BKO) como se muestra.Apriete los elementos sólo a

mano en este paso.

• Repeat steps 2.4 through 2.7 to as-

semble the other A-Frame.

• Répétez étapes 2,4 – 2,7 pour monter

l’autre Cadre en « A ».

• Repita pasos 2,4 – 2.7 para armar el

otro Armazón en «A».

BFB (x8)

DXT (x4)

BTS (x4)

BFC (x8)

DSA (x4)

ALH

BKQ

BFB

BKO

Straight Edge

Bord droit

Borde derecho

DSA

DXT

BTS

BKN

2.8

• Attach a Turn Bar (BKN) to the assembled A-Frame with the hardware shown.

• Attachez une Barre horizontale (BKN) au Cadre en « A » à l’aide des accessoires requis.

• Sujete la Barra (BKN) al Conjunto del armazón en «A» usando los elementos requeridos.

3/16 in/po (≈5 mm)

7/32 in/po (≈6 mm)

9/16 in/po (≈14 mm)

(1)

(2)

BFC

HARDWARE REQUIRED / ACCESSOIRES REQUIS / HERRAJE REQUERIDO

BFH

PARTS REQUIRED / PIÈCES REQUISES / PIEZAS REQUERIDAS

TOOLS REQUIRED / OUTILS REQUIS / INSTRUMENTAL REQUERIDO

7/32 in/po (≈6 mm)

9/16 in/po (≈14 mm)

(1)

(2)

CONTENTS OF BOX 2 / CONTENU DE LA BOÎTE 2 / CONTENIDO DE LA CAJA 2

FINAL ASSEMBLY / ASSEMBLAGE FINAL / ENSAMBLE FINAL

BFB (x4)

BFC (x4)

ARO (x8)

BKT (x2)

BKU (x1)

BFD (x4)

Hardware Bag / Sac d’accessoires / Bolsa de herraje

(1)

TOOLS AND HARDWARE REQUIRED / OUTILS ET ACCESSOIRES REQUIS / INSTRUMENTAL Y HERRAJE REQUERIDOS

X SECTION 3 (CONTINUED) / SECTION 3 (SUITE) / SECCIÓN 3 (CONTINUACIÓN)

• Attach the Swing Bar Assembly to an A-Frame Assembly as shown with the hardware indicated. For easier

assembly, secure the outside hardware ﬁ rst. Return to section two to tighten the hardware in step 2.6. Tighten

the hardware from step 2.6 before continuing to the next step.

• Attachez l’Ensemble de la barre de balançoire à l’Ensemble du Cadre en « A » comme illustré à l’aide des

accessoires requis. Pour faciliter le montage, serrez les accessoires extérieurs en premier. Retournez à

Section 2 pour serrer les accessoires de l’étape 2,6. Serrez les accessoires de l’étape 2,6 avant de continuer

à la prochaine étape.

• Sujete el Conjunto de la barra de columpio a un Conjunto de armazón en «A» como se muestra y con los

elementos requeridos. Para facilitar el armado, asegure los elementos exteriores primero. Vuelva a Sección 2

para apretar los elementos en paso 2,6. Apriete todos los elementos de ﬁ jación del paso 2,6 antes de continuar

al próximo paso.

3.1

• Repeat this step to assemble the other A-Frame Assembly to the other side of the Swing Bar Assembly.

• Répétez cetter étape pour monter l’autre Cadre en « A » à l’autre côté de la Barre de balançoire.

• Repita este paso para armar el otro Conjunto de armazón en «A» al otro lado del Conjunto de la barra

de columpio.

BFB (x4)

BFC (x4)

BFB

BFC

BFB

7/32 in/po (≈6 mm)

9/16 in/po (≈14 mm)

(1)

(2)

Page is loading ...

Lifetime 290038 Owner's manual

Brand: Lifetime

Model: 290038

Type: Owner's manual

Download PDF

report

in other languages

français: Lifetime 290038 Le manuel du propriétaire
español: Lifetime 290038 El manual del propietario

Lifetime 290038 Owner's manual

Lifetime 290038 Owner's manual

in other languages

Related papers

Other documents