Danfoss BasicRail / BasicClip - Cement screed User guide

Danfoss
Brand
Danfoss
Model
BasicRail / BasicClip - Cement screed
Type
User guide

Danfoss BasicRail / BasicClip - Cement screed is a system for installing underfloor heating in residential and commercial buildings. It is a cost-effective and easy-to-install system that can be used with a variety of floor finishes, including carpet, tile, parquet and laminate. The system consists of two main components: BasicRail and BasicClip.

BasicRail is a lightweight, aluminium rail that is fixed to the subfloor using screws or adhesive. BasicClip is a plastic clip that is attached to the BasicRail and holds the heating pipe in place.

The Danfoss BasicRail / BasicClip system offers a number of advantages over traditional underfloor heating systems. It is lightweight and easy to install, it can be used with a variety of floor finishes and it provides excellent thermal performance. The system is also very durable and can withstand heavy loads.

Danfoss BasicRail / BasicClip - Cement screed is a system for installing underfloor heating in residential and commercial buildings. It is a cost-effective and easy-to-install system that can be used with a variety of floor finishes, including carpet, tile, parquet and laminate. The system consists of two main components: BasicRail and BasicClip.

BasicRail is a lightweight, aluminium rail that is fixed to the subfloor using screws or adhesive. BasicClip is a plastic clip that is attached to the BasicRail and holds the heating pipe in place.

The Danfoss BasicRail / BasicClip system offers a number of advantages over traditional underfloor heating systems. It is lightweight and easy to install, it can be used with a variety of floor finishes and it provides excellent thermal performance. The system is also very durable and can withstand heavy loads.

Carpet / Tiles / Parquet /
Laminate / Synthetics
1 Carpet / tiles / parquet
2 Cement screed 85 mm
3 FH composite pipe / FH PE-RT pipe (16 mm)
4 Basic Insulation overlap panels 35-3 35 mm
5 Basic perimeter insulation
Technical Data
Floor finish NA mm Carpet / tiles / parquet / laminate / synthetics
Construction height 120 mm Height excluding floor finish
Weight ~ 176 kg/m² Weight excluding floor finish
Thermal resistance (R) 0.77 m²K/W Thermal resistance value for Basic overlap panel
Thermal transmission
coefficient (U)
1.06 W/m²K Be aware that building regulations can specify
better thermal insulation
Distribution load ≤ 2.0 kN/m²
Point load (≥ 20 cm²) ≤ 2.0 kN
Impact subsonic noise
reduction
29 dB Calculated value according to DIN 4109; applies to
concrete slabs thicker than 12 cm (DIN 4109: m² >
276 kg/m²)
Application area Rooms in residential bulildings and houses; bedrooms and wards in hospitals;
bedrooms in hotels and hostels kitchens and toilets. Correponding to category
A of EN 1991. Office areas. Correponding to category B of EN 1991.
Requirements &
special features
The screed thicknesses must be adjusted in case of higher design load or point
load values. Structural sealing according to EN 13967 must be placed beneath
the floor panel in case of structures facing the ground, and otherwise on the
unfinished floor. Observe all installation instructions and manufacturer’s
instructions.
Additional
insulation
For thermal resistance table and insulation thickness, please refer to the Basic
handbook.
Construction Referring to EN 1264, ISO EN 140-8, EN 1991, EN 13813, EN 13967 and local
building regulations.
Construction number 544
Application Sheet
BasicRail / BasicClip - Cement Screed
Danfoss Heating Solutions VAEKG302 © Danfoss 11/2010 1
Application Sheet BasicRail / BasicClip - Cement Screed
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone:+45 7488 8000
Fax: +45 7488 8100
Email: [email protected]
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
2 VAEKG302 © Danfoss 11/2010 Danfoss Heating Solutions
  • Page 1 1
  • Page 2 2

Danfoss BasicRail / BasicClip - Cement screed User guide

Danfoss
Brand
Danfoss
Model
BasicRail / BasicClip - Cement screed
Type
User guide

Danfoss BasicRail / BasicClip - Cement screed is a system for installing underfloor heating in residential and commercial buildings. It is a cost-effective and easy-to-install system that can be used with a variety of floor finishes, including carpet, tile, parquet and laminate. The system consists of two main components: BasicRail and BasicClip.

BasicRail is a lightweight, aluminium rail that is fixed to the subfloor using screws or adhesive. BasicClip is a plastic clip that is attached to the BasicRail and holds the heating pipe in place.

The Danfoss BasicRail / BasicClip system offers a number of advantages over traditional underfloor heating systems. It is lightweight and easy to install, it can be used with a variety of floor finishes and it provides excellent thermal performance. The system is also very durable and can withstand heavy loads.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents